Loaded MCU 'beacon' 45 commands (Beacon 2.1.0 / )
MCU 'beacon' config: ADC_MAX=4095 BEACON_ACCEL_BITS=12 BEACON_ACCEL_SCALE_16G=7.81 BEACON_ACCEL_SCALE_2G=0.98 BEACON_ACCEL_SCALE_4G=1.95 BEACON_ACCEL_SCALE_8G=3.91 BEACON_ADC_SMOOTH_COUNT=16 BEACON_HAS_ACCEL=1 BEACON_REV=H CLOCK_FREQ=32000000 MCU=beacon STATS_SUMSQ_BASE=256
Configured MCU 'beacon' (0 moves)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	x1_step_pin=PF9,
	x1_dir_pin=PF10,
	x1_enable_pin=PG2,
	x1_uart_pin=PF2,
	x1_diag_pin=PG12,
	x1_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA0,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null

[mcu]
serial = /dev/RatOS/btt-octopus-11

[temperature_sensor Octopus_V1.1_F446]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_bus = spi3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD0,
	e_dir_pin=PD1,
	e_enable_pin=PD2,
	e_uart_pin=PA15,
	
	e_heater_pin=PB13,
	e_sensor_pin=PA3,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB12,
	bltouch_sensor_pin=PB8,
	bltouch_control_pin=PB9,
	probe_pin=PB9,
	fan_part_cooling_pin=PA0,
	fan_toolhead_cooling_pin=PA1,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-12-t0

[temperature_sensor EBB42_v1.2_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[adxl345 toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB12
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "back"
variable_start_print_park_z_height = 50
variable_end_print_park_in = "back"
variable_pause_print_park_in = "front"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = False
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.8, 59.8]
variable_bed_margin_y = [14.35, 30]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_true_zero_temp = 150
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = False
variable_beacon_scan_compensation_profile = "Contact"
variable_beacon_scan_compensation_probe_count = 15,15
variable_beacon_contact_poke_bottom_limit = -1
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_x_driver_types = ["tmc2209"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_y_axes = ["x1", "y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_homing %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	STOW_PROBE
	{% else %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_homing %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.configfile.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.configfile.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.configfile.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.configfile.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.configfile.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro _MOVE_TO_SAFE_Z_HOME]
description = Move to safe home position with optional Z_HOP (pass Z_HOP=True as parameter)
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	{% if params.Z_HOP is defined %}
	_Z_HOP
	{% endif %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, safe_home_x: {safe_home_x}, safe_home_y: {safe_home_y}, printable_x_max: {printable_x_max}, printable_y_max: {printable_y_max}"
	
	
	G0 X{safe_home_x} Y{safe_home_y} F{speed}

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis
variable_is_kinematic_position_overriden = False
gcode = 
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed, skipping.."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting presssure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_PARKING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_PARKING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined %}
	
	
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if act_t == toolhead %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% if printer.configfile.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE={default_profile} X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode}
	{% else %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD={default_profile}
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD={printer["gcode_macro RatOS"].bed_mesh_profile}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Recieved coordinates X0={x0} Y0={y0} X1={x1} Y1={y1}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% else %}
	
	{% set mesh_config = printer.configfile.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and printer.configfile.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.configfile.settings.beacon is defined and printer.configfile.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0} Y0={mesh_y0} X1={mesh_x1} Y1={mesh_y1}"
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile} ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile} ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	{% if printer["dual_carriage"] is defined %}
	
	_SET_TOOLHEAD_OFFSET T={printer["gcode_macro RatOS"].default_toolhead|int} MOVE=0
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0 MOVE=0
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% else %}
	M104.1 S{s} T{t}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% endif %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for toolhead T{t} reached."

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_ORG
gcode = 
	SET_GCODE_OFFSET_ORG { rawparams }
	{% if printer.configfile.settings.beacon is defined and (params.Z_ADJUST is defined or params.Z is defined) %}
	_BEACON_APPLY_RUNTIME_MULTIPLIER
	{% endif %}

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.configfile.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.configfile.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.configfile.settings.bltouch is defined  %}
	{% set config_offset = printer.configfile.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.configfile.settings.probe is defined  %}
	{% set config_offset = printer.configfile.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.configfile.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.configfile.config.bed_mesh %}
	
	
	{% if printer.configfile.settings.bltouch is defined %}
	{% set x_offset = printer.configfile.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.configfile.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.configfile.settings.bltouch.z_offset|float %}
	{% elif printer.configfile.settings.probe is defined %}
	{% set x_offset = printer.configfile.settings.probe.x_offset|float %}
	{% set y_offset = printer.configfile.settings.probe.y_offset|float %}
	{% set z_offset = printer.configfile.settings.probe.z_offset|float %}
	{% elif printer.configfile.settings.beacon is defined %}
	{% set x_offset = printer.configfile.settings.beacon.x_offset|float %}
	{% set y_offset = printer.configfile.settings.beacon.y_offset|float %}
	{% set z_offset = printer.configfile.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.configfile.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.configfile.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.configfile.settings.bltouch is not defined and printer.configfile.settings.probe is not defined and printer.configfile.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.configfile.settings.bltouch is not defined and printer.configfile.settings.probe is not defined and printer.configfile.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET TOOLHEAD={current_toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F300 E{14 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead}
	{% endif %}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead}

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}"
	
	{% if not printer.virtual_sdcard.is_active %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull finished!" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	_LED_STANDBY
	CALCULATE_PRINTABLE_AREA
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	HELLO_RATOS

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
gcode = 
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.configfile.settings.ratos_hybrid_corexy is defined and printer.configfile.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.configfile.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro SAVE_Z_OFFSET]
gcode = 
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_SAVE_MULTIPLIER
	{% else %}
	Z_OFFSET_APPLY_PROBE
	{% endif %}

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.configfile.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING

[gcode_macro CANCEL_PRINT]
description = Cancels the printer
rename_existing = CANCEL_PRINT_BASE
gcode = 
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.configfile.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.configfile.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.configfile.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.configfile.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.configfile.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.configfile.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == '' %}
	_SET_TOOLHEAD_OFFSET T={default_toolhead} MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% set x_offset = printer.toolhead.position.x|float - printer.gcode_move.gcode_position.x|float %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	{% if idex_mode != '' %}
	
	{% set act_idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% if act_idex_mode == "copy" or act_idex_mode == "mirror" %}
	SET_GCODE_OFFSET X={x_offset} MOVE=0
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	{% if initial_tool != default_toolhead %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	SAVE_VARIABLE VARIABLE=idex_applied_offset VALUE={default_toolhead}
	
	_SET_TOOLHEAD_OFFSET T={initial_tool} MOVE=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	
	
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	_BEACON_SET_NOZZLE_TEMP_OFFSET TOOLHEAD={initial_tool}
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	{% if auto_z_offset_calibration %}
	{% set safe_distance = printer.configfile.settings.dual_carriage.safe_distance|float %}
	{% if default_toolhead == 0 %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	G1 X{safe_home_x - safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{safe_home_x + safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% elif default_toolhead == 1 %}
	_SELECT_TOOL T=1 TOOLSHIFT=false
	G1 X{safe_home_x + safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{safe_home_x - safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	{% endif %}
	{% else %}
	_MOVE_TO_SAFE_Z_HOME
	{% endif %}
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead}
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1}
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1
	BEACON_QUERY

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_true_zero_location = printer["gcode_macro RatOS"].beacon_contact_true_zero_location|default("front")|lower %}
	{% set beacon_contact_true_zero_margin_x = printer["gcode_macro RatOS"].beacon_contact_true_zero_margin_x|default(30)|int %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead}
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead}
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	SET_GCODE_OFFSET Z=0 MOVE=0
	{% endif %}
	{% endif %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	G91
	
	G1 E-2 F3600
	
	G0 Z{z_safe} F3600
	
	G1 E-{(r-2)} F3600
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS parameter for if you only want to do one axis at a time, (eg. GENERATE_SHAPER_GRAPHS AXIS=X)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=X FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_x
	
	{% elif axis == 'y' %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=Y FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_y
	
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=X FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	TEST_RESONANCES AXIS=Y FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_x
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_y
	
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned.
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	MAYBE_HOME
	TEST_RESONANCES AXIS=1,1  OUTPUT=raw_data NAME=belt-tension-upper FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	TEST_RESONANCES AXIS=1,-1 OUTPUT=raw_data NAME=belt-tension-lower FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_belt_tension_graph
	
	
	
	_LED_INPUT_SHAPER_END
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_LEARN_MORE_CALIBRATION
	
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
allow_unsupported_slicer_versions = True
bypass_post_processing = True

[exclude_object]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.02
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114

[fan]
pin = !toolboard_t0:PA0
shutdown_speed = 1.0
cycle_time = 0.00004

[heater_fan toolhead_cooling_fan]
pin = toolboard_t0:PA1
fan_speed = 1
heater = extruder

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[delayed_gcode _HYBRID_INIT]
initial_duration = 0.1
gcode = 
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}

[stepper_x]
position_max = 559.8
position_endstop = -59.8
position_min = -59.8
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40
homing_speed = 50
endstop_pin = toolboard_t0:PB6

[stepper_y]
position_max = 530
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4
position_min = -5
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[bed_mesh]
horizontal_move_z = 2
mesh_min = 20,30
mesh_max = 470,450
probe_count = 40,40
fade_start = 1.0
fade_end = 10.0
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	30,30
	250,450
	470,30
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 4.63
full_steps_per_rotation = 200
filament_diameter = 1.750
max_extrude_only_velocity = 60
max_extrude_only_distance = 200
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB13
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA3
min_extrude_temp = 170
min_temp = 0
max_temp = 350
pressure_advance = 0.03
step_pin = toolboard_t0:PD0
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PD2
microsteps = 64
control = pid
pid_kp = 36.824
pid_ki = 12.275
pid_kd = 27.618

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.5

[resonance_tester]
accel_chip_x = adxl345 toolboard_t0
accel_chip_y = adxl345 toolboard_t0
probe_points = 
	250,250,20

[tmc2209 stepper_x]
stealthchop_threshold = 0
interpolate = False
uart_pin = PC4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_x1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PF2
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_x1]
step_pin = PF9
dir_pin = x1_dir_pin
enable_pin = !PG2
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40

[tmc2209 stepper_y]
stealthchop_threshold = 0
interpolate = False
uart_pin = PD11
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_y1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PC7
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA0
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = False
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = False
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PA15
run_current = 0.707
driver_tbl = 0
driver_toff = 4
driver_hend = 6
driver_hstrt = 7
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 22.5
mesh_main_direction = x
mesh_runs = 1
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	
	
	{% set svv = printer.save_variables.variables %}
	{% set nozzle_expansion_coefficient_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(0)|float %}
	{% if nozzle_expansion_coefficient_multiplier == 0 %}
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is not defined %}
	{% set nozzle_expansion_coefficient_multiplier = 1.0 %}
	{% else %}
	{% set nozzle_expansion_coefficient_multiplier = printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier|default(1.0)|float %}
	{% endif %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier VALUE={nozzle_expansion_coefficient_multiplier}
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG={'"Please remove the variable beacon_contact_expansion_multiplier from your config file."'}
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_MEASURE_GANTRY_TWIST
	_BEACON_MAYBE_SCAN_COMPENSATION
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	G0 Z2 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set test_margin = 30 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
variable_runtime_temp = 0
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(0)|int %}
	{% set reset = true if params.RESET|default(false)|lower == 'true' else false %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if reset %}
	
	SAVE_VARIABLE VARIABLE=nozzle_expansion_applied_offset VALUE=0
	
	{% else %}
	{% if beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set nozzle_expansion_coefficient_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(1.0)|float %}
	
	
	{% set applied_offset = svv.nozzle_expansion_applied_offset|default(0)|float %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_offset = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = nozzle_expansion_coefficient_multiplier * (temp_offset * (expansion_coefficient / 100)) %}
	
	
	{% set new_offset = ((-applied_offset) + expansion_offset) %}
	SET_GCODE_OFFSET Z_ADJUST={new_offset} MOVE=1 SPEED={z_speed}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_applied_offset VALUE={expansion_offset}
	SET_GCODE_VARIABLE MACRO=_BEACON_SET_NOZZLE_TEMP_OFFSET VARIABLE=runtime_temp VALUE={temp}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="multiplier: {nozzle_expansion_coefficient_multiplier}, coefficient: {expansion_coefficient}, temp_offset: {temp_offset}, expansion_offset: {expansion_offset}, applied_offset: {applied_offset}, new_offset: {new_offset}"
	
	{% endif %}
	{% endif %}

[gcode_macro BEACON_MEASURE_GANTRY_TWIST]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure gantry twist..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_GANTRY_TWIST
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_PROBE_GANTRY_TWIST]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE
	BEACON_QUERY

[gcode_macro _BEACON_STORE_GANTRY_TWIST]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_GANTRY_TWIST]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low gantry twist: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low gantry twist: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High gantry twist: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High gantry twist: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high gantry twist: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Gantry twist relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("Contact")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set probe_count = printer["gcode_macro RatOS"].beacon_scan_compensation_probe_count %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	{% endif %}
	
	
	{% if not automated %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES=2 SAMPLES_DROP=1 SAMPLES_TOLERANCE_RETRIES=10 PROBE_COUNT={probe_count[0]},{probe_count[1]} PROFILE={profile}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE={beacon_scan_compensation_profile}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}

[gcode_macro _BEACON_SAVE_MULTIPLIER]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% set multiplier = printer["gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER"].runtime_multiplier|default(-1.0)|float %}
	
	DEBUG_ECHO PREFIX="_BEACON_SAVE_MULTIPLIER" MSG="multiplier: {multiplier}, beacon_contact_start_print_true_zero: {beacon_contact_start_print_true_zero}, beacon_contact_expansion_compensation: {beacon_contact_expansion_compensation}"
	
	{% if multiplier > 0 and beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier VALUE={multiplier}
	SET_GCODE_VARIABLE MACRO=_BEACON_APPLY_RUNTIME_MULTIPLIER VARIABLE=runtime_multiplier VALUE=-1.0
	CONSOLE_ECHO TITLE="Hotend thermal expansion compensation" TYPE="success" MSG={'"New value is: %.6f_N_The new multiplier value has been saved to the configuration."' % multiplier}
	{% else %}
	Z_OFFSET_APPLY_PROBE
	{% endif %}

[gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER]
variable_runtime_multiplier = -1.0
gcode = 
	
	{% set toolhead = 0 %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	{% if layer_number == 0 and is_printing_gcode %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Documentation" %}
	{% set line_1 = '"Your slicer is not correctly reporting layer information. See the layer change custom g-code in the <a href="%s" target="_blank" >%s</a>".' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Missing layer information" TYPE="warning" MSG={line_1}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_RUNTIME_MULTIPLIER" MSG="layer_number: {layer_number}, is_printing_gcode: {is_printing_gcode}, beacon_contact_start_print_true_zero: {beacon_contact_start_print_true_zero}, beacon_contact_expansion_compensation: {beacon_contact_expansion_compensation}"
	
	{% if layer_number == 1 and is_printing_gcode and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if toolhead == 1 %}
	{% set nozzle_expansion_coefficient = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set beacon_contact_expansion_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(1.0)|float %}
	{% set print_temp = printer["gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET"].runtime_temp|default(0)|int %}
	
	{% if print_temp > 0 %}
	{% set z_offset = printer.gcode_move.homing_origin.z|float %}
	{% set temp_delta = print_temp - beacon_contact_true_zero_temp %}
	{% set coefficient_per_degree = nozzle_expansion_coefficient / 100 %}
	{% set z_offset_per_degree = z_offset / temp_delta %}
	{% set new_multiplier = z_offset_per_degree / coefficient_per_degree %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_RUNTIME_MULTIPLIER" MSG="print_temp: {print_temp}, z_offset: {z_offset}, temp_delta: {temp_delta}, nozzle_expansion_coefficient: {nozzle_expansion_coefficient}, coefficient_per_degree: {coefficient_per_degree}, z_offset_per_degree: {z_offset_per_degree}, old_multiplier: {beacon_contact_expansion_multiplier}, new_multiplier: {new_multiplier}"
	SET_GCODE_VARIABLE MACRO=_BEACON_APPLY_RUNTIME_MULTIPLIER VARIABLE=runtime_multiplier VALUE={new_multiplier}
	
	{% endif %}
	
	{% endif %}

[controller_fan controller_fan]
pin = PD12

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = False
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = False
variable_has_front_arm_nozzle_wiper = False
variable_resume_after_insert = False
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[filament_switch_sensor toolhead_filament_sensor_t0]
pause_on_runout = False
event_delay = 0.1
switch_pin = ^toolboard_t0:PB3
runout_gcode = 
	_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT TOOLHEAD=0
insert_gcode = 
	_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT TOOLHEAD=0

[gcode_button toolhead_filament_sensor_button_t0]
pin = ^!toolboard_t0:PB4
release_gcode = 
	_ON_FILAMENT_SENSOR_BUTTON_PRESSED TOOLHEAD=0
press_gcode = 

[output_pin caselight]
pin = PB11
pwm = True
cycle_time = 0.01
scale = 1.0
value = 1.0
shutdown_value = 0.0

[beacon model default]
model_coef = 1.5262425407123157,
	1.8789172227584032,
	0.847501001243572,
	0.4711280696377741,
	0.1746215419233843,
	-0.10944706696469403,
	-0.09554682575881597,
	0.15659764883575533,
	0.1469143147360675,
	0.005551915327827087
model_domain = 1.8559999301614767e-07,1.9376090302482318e-07
model_range = 0.200000,5.000000
model_temp = 51.224324
model_offset = 0.00000
=======================
Loaded MCU 'mcu' 144 commands (v0.13.0-272-g1be6c0fce / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_sdio=PC12,PD2,PC8,PC9,PC10,PC11 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1_PA6_PA7_PA5=PA6,PA7,PA5 BUS_PINS_spi1_PB4_PB5_PB3=PB4,PB5,PB3 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB14_PB15_PB13=PB14,PB15,PB13 BUS_PINS_spi2_PC2_PC3_PB10=PC2,PC3,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3_PB4_PB5_PB3=PB4,PB5,PB3 BUS_PINS_spi3_PC11_PC12_PC10=PC11,PC12,PC10 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 BUS_PINS_spi4_PE13_PE14_PE12=PE13,PE14,PE12 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=257 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_OPTIMIZED_EDGE=23 STEPPER_STEP_BOTH_EDGE=1
Configured MCU 'mcu' (1024 moves)
Loaded MCU 'rpi' 119 commands (?-20240727_132503-fv-az659-741 / gcc: (Raspbian 10.2.1-6+rpi1) 10.2.1 20210110 binutils: (GNU Binutils for Raspbian) 2.35.2)
MCU 'rpi' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
Configured MCU 'rpi' (1024 moves)
Loaded MCU 'toolboard_t0' 113 commands (v0.12.0-268-g0844388d / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'toolboard_t0' (1024 moves)
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-396-gb7233d119-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/ratos.py, klippy/extras/ratos_homing.py, klippy/extras/resonance_generator.py, klippy/extras/z_offset_probe.py, klippy/kinematics/ratos_hybrid_corexy.py
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Mar 20 2025, 22:21:41) \n[GCC 10.2.1 20210110]'
webhooks client 4123225008: {'program': 'Moonraker', 'version': 'v0.9.3-116-gb11a791'}
=============== Log rollover at Fri Sep 26 12:26:20 2025 ===============
Starting SD card print (position 0)
Error evaluating 'gcode_macro START_PRINT:gcode': gcode.CommandError: Filament not detected! Toolhead T0 filament sensor is empty.
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/extras/gcode_macro.py", line 61, in render
    return str(self.template.render(context))
  File "/home/pi/klippy-env/lib/python3.9/site-packages/jinja2/environment.py", line 1090, in render
    self.environment.handle_exception()
  File "/home/pi/klippy-env/lib/python3.9/site-packages/jinja2/environment.py", line 832, in handle_exception
    reraise(*rewrite_traceback_stack(source=source))
  File "/home/pi/klippy-env/lib/python3.9/site-packages/jinja2/_compat.py", line 28, in reraise
    raise value.with_traceback(tb)
  File "<template>", line 208, in top-level template code
  File "/home/pi/klipper/klippy/extras/gcode_macro.py", line 89, in _action_raise_error
    raise self.printer.command_error(msg)
gcode.CommandError: Filament not detected! Toolhead T0 filament sensor is empty.
Error evaluating 'gcode_macro START_PRINT:gcode': gcode.CommandError: Filament not detected! Toolhead T0 filament sensor is empty.

Exiting SD card print (position 41100)
Filament Sensor toolhead_filament_sensor_t0: insert event detected, Time 70452.15
FORCE_MOVE extruder distance=5.000 velocity=1.000 accel=0.000
Stats 70452.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421047 bytes_read=7895785 bytes_retransmit=9 bytes_invalid=0 send_seq=69855 receive_seq=69855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999627 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=418104 bytes_read=1289333 bytes_retransmit=0 bytes_invalid=0 send_seq=69651 receive_seq=69651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998460 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=419092 bytes_read=7664691 bytes_retransmit=9 bytes_invalid=0 send_seq=69714 receive_seq=69714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999554 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417633 bytes_read=24322345 bytes_retransmit=9 bytes_invalid=0 send_seq=69601 receive_seq=69601 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999944 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.10 cputime=3370.224 memavail=1411324 print_time=70463.021 buffer_time=5.239 print_stall=0 extruder: target=0 temp=25.0 pwm=0.000
Stats 70453.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421069 bytes_read=7895893 bytes_retransmit=9 bytes_invalid=0 send_seq=69857 receive_seq=69857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999634 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418110 bytes_read=1289362 bytes_retransmit=0 bytes_invalid=0 send_seq=69652 receive_seq=69652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998441 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=419126 bytes_read=7664837 bytes_retransmit=9 bytes_invalid=0 send_seq=69717 receive_seq=69717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999607 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.5 raspberry_pi: temp=32.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417639 bytes_read=24322701 bytes_retransmit=9 bytes_invalid=0 send_seq=69602 receive_seq=69602 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999929 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.10 cputime=3370.284 memavail=1411324 print_time=70463.021 buffer_time=4.239 print_stall=0 extruder: target=0 temp=25.0 pwm=0.000
Stats 70454.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421075 bytes_read=7895996 bytes_retransmit=9 bytes_invalid=0 send_seq=69858 receive_seq=69858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999635 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418116 bytes_read=1289378 bytes_retransmit=0 bytes_invalid=0 send_seq=69653 receive_seq=69653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=419160 bytes_read=7664983 bytes_retransmit=9 bytes_invalid=0 send_seq=69720 receive_seq=69720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999596 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417645 bytes_read=24323057 bytes_retransmit=9 bytes_invalid=0 send_seq=69603 receive_seq=69603 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999934 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.09 cputime=3370.343 memavail=1411524 print_time=70463.021 buffer_time=3.239 print_stall=0 extruder: target=0 temp=25.0 pwm=0.000
Stats 70455.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421081 bytes_read=7896126 bytes_retransmit=9 bytes_invalid=0 send_seq=69859 receive_seq=69859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999637 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418122 bytes_read=1289394 bytes_retransmit=0 bytes_invalid=0 send_seq=69654 receive_seq=69654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998430 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=419194 bytes_read=7665157 bytes_retransmit=9 bytes_invalid=0 send_seq=69723 receive_seq=69723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999597 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=30.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417651 bytes_read=24323413 bytes_retransmit=9 bytes_invalid=0 send_seq=69604 receive_seq=69604 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999937 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.09 cputime=3370.404 memavail=1411580 print_time=70463.021 buffer_time=2.238 print_stall=0 extruder: target=0 temp=25.0 pwm=0.000
Stats 70456.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421087 bytes_read=7896223 bytes_retransmit=9 bytes_invalid=0 send_seq=69860 receive_seq=69860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418128 bytes_read=1289410 bytes_retransmit=0 bytes_invalid=0 send_seq=69655 receive_seq=69655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998428 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=419228 bytes_read=7665318 bytes_retransmit=9 bytes_invalid=0 send_seq=69726 receive_seq=69726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999595 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417657 bytes_read=24323769 bytes_retransmit=9 bytes_invalid=0 send_seq=69605 receive_seq=69605 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999960 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.09 cputime=3370.466 memavail=1411580 print_time=70463.021 buffer_time=1.238 print_stall=0 extruder: target=0 temp=25.0 pwm=0.000
Stats 70457.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421093 bytes_read=7896337 bytes_retransmit=9 bytes_invalid=0 send_seq=69861 receive_seq=69861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418134 bytes_read=1289426 bytes_retransmit=0 bytes_invalid=0 send_seq=69656 receive_seq=69656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998414 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=419274 bytes_read=7665463 bytes_retransmit=9 bytes_invalid=0 send_seq=69730 receive_seq=69730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999573 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417663 bytes_read=24324125 bytes_retransmit=9 bytes_invalid=0 send_seq=69606 receive_seq=69606 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999949 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.09 cputime=3370.529 memavail=1411584 print_time=70463.021 buffer_time=0.238 print_stall=0 extruder: target=0 temp=24.9 pwm=0.000
RatOS:: Heating extruder to 220C... Please wait.
RatOS | TEMPERATURE_WAIT:: Waiting for sensor: extruder, MINIMUM: 220
RatOS:: please wait...
Stats 70458.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421099 bytes_read=7896469 bytes_retransmit=9 bytes_invalid=0 send_seq=69862 receive_seq=69862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418140 bytes_read=1289455 bytes_retransmit=0 bytes_invalid=0 send_seq=69657 receive_seq=69657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998414 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=419324 bytes_read=7665633 bytes_retransmit=9 bytes_invalid=0 send_seq=69734 receive_seq=69734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999572 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417669 bytes_read=24324472 bytes_retransmit=9 bytes_invalid=0 send_seq=69607 receive_seq=69607 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999958 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.09 cputime=3370.621 memavail=1411584 print_time=70463.315 buffer_time=0.000 print_stall=0 extruder: target=220 temp=25.7 pwm=1.000
Heater extruder approaching new target of 220.000
Stats 70459.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421105 bytes_read=7896572 bytes_retransmit=9 bytes_invalid=0 send_seq=69863 receive_seq=69863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418146 bytes_read=1289471 bytes_retransmit=0 bytes_invalid=0 send_seq=69658 receive_seq=69658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998423 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=419373 bytes_read=7665777 bytes_retransmit=9 bytes_invalid=0 send_seq=69738 receive_seq=69738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999569 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.7 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417675 bytes_read=24324817 bytes_retransmit=9 bytes_invalid=0 send_seq=69608 receive_seq=69608 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999952 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3370.680 memavail=1406560 print_time=70464.316 buffer_time=0.000 print_stall=0 extruder: target=220 temp=37.2 pwm=1.000
Stats 70460.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421111 bytes_read=7896675 bytes_retransmit=9 bytes_invalid=0 send_seq=69864 receive_seq=69864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999646 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418152 bytes_read=1289487 bytes_retransmit=0 bytes_invalid=0 send_seq=69659 receive_seq=69659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998425 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=419407 bytes_read=7665916 bytes_retransmit=9 bytes_invalid=0 send_seq=69741 receive_seq=69741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999568 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=30.6 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417681 bytes_read=24325162 bytes_retransmit=9 bytes_invalid=0 send_seq=69609 receive_seq=69609 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999951 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3370.707 memavail=1411124 print_time=70465.317 buffer_time=0.000 print_stall=0 extruder: target=220 temp=47.0 pwm=1.000
Stats 70461.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421117 bytes_read=7896807 bytes_retransmit=9 bytes_invalid=0 send_seq=69865 receive_seq=69865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999642 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418158 bytes_read=1289503 bytes_retransmit=0 bytes_invalid=0 send_seq=69660 receive_seq=69660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998406 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419441 bytes_read=7666101 bytes_retransmit=9 bytes_invalid=0 send_seq=69744 receive_seq=69744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999575 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=30.7 raspberry_pi: temp=32.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417687 bytes_read=24325507 bytes_retransmit=9 bytes_invalid=0 send_seq=69610 receive_seq=69610 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999947 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3370.732 memavail=1411124 print_time=70466.318 buffer_time=0.000 print_stall=0 extruder: target=220 temp=58.8 pwm=1.000
Stats 70462.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421123 bytes_read=7896924 bytes_retransmit=9 bytes_invalid=0 send_seq=69866 receive_seq=69866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999640 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418164 bytes_read=1289519 bytes_retransmit=0 bytes_invalid=0 send_seq=69661 receive_seq=69661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998398 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419491 bytes_read=7666252 bytes_retransmit=9 bytes_invalid=0 send_seq=69748 receive_seq=69748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999576 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=30.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417693 bytes_read=24325852 bytes_retransmit=9 bytes_invalid=0 send_seq=69611 receive_seq=69611 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999915 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.08 cputime=3370.758 memavail=1411124 print_time=70467.319 buffer_time=0.000 print_stall=0 extruder: target=220 temp=66.7 pwm=1.000
Stats 70463.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421129 bytes_read=7897027 bytes_retransmit=9 bytes_invalid=0 send_seq=69867 receive_seq=69867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=418170 bytes_read=1289535 bytes_retransmit=0 bytes_invalid=0 send_seq=69662 receive_seq=69662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998379 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419525 bytes_read=7666398 bytes_retransmit=9 bytes_invalid=0 send_seq=69751 receive_seq=69751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999564 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=30.7 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417699 bytes_read=24326197 bytes_retransmit=9 bytes_invalid=0 send_seq=69612 receive_seq=69612 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999907 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.08 cputime=3370.783 memavail=1410624 print_time=70468.319 buffer_time=0.000 print_stall=0 extruder: target=220 temp=74.3 pwm=1.000
Stats 70464.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421135 bytes_read=7897159 bytes_retransmit=9 bytes_invalid=0 send_seq=69868 receive_seq=69868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000013 bytes_write=418176 bytes_read=1289564 bytes_retransmit=0 bytes_invalid=0 send_seq=69663 receive_seq=69663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998326 adj=49998344 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419567 bytes_read=7666588 bytes_retransmit=9 bytes_invalid=0 send_seq=69755 receive_seq=69755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999569 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.8 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417705 bytes_read=24326542 bytes_retransmit=9 bytes_invalid=0 send_seq=69613 receive_seq=69613 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999888 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.08 cputime=3370.816 memavail=1410372 print_time=70469.320 buffer_time=0.000 print_stall=0 extruder: target=220 temp=83.5 pwm=1.000
Stats 70465.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421141 bytes_read=7897262 bytes_retransmit=9 bytes_invalid=0 send_seq=69869 receive_seq=69869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000013 bytes_write=418182 bytes_read=1289580 bytes_retransmit=0 bytes_invalid=0 send_seq=69664 receive_seq=69664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998296 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419601 bytes_read=7666737 bytes_retransmit=9 bytes_invalid=0 send_seq=69758 receive_seq=69758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999569 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.8 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417711 bytes_read=24326887 bytes_retransmit=9 bytes_invalid=0 send_seq=69614 receive_seq=69614 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999886 coil_temp=25.3 refs=0 mcu_temp=23.97 supply_voltage=3.013 sysload=0.08 cputime=3370.875 memavail=1410372 print_time=70470.321 buffer_time=0.000 print_stall=0 extruder: target=220 temp=90.1 pwm=1.000
Stats 70466.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421153 bytes_read=7897381 bytes_retransmit=9 bytes_invalid=0 send_seq=69871 receive_seq=69871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000013 bytes_write=418188 bytes_read=1289596 bytes_retransmit=0 bytes_invalid=0 send_seq=69665 receive_seq=69665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998333 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419657 bytes_read=7666903 bytes_retransmit=9 bytes_invalid=0 send_seq=69763 receive_seq=69763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999552 Octopus_V1.1_F446: temp=26.4 EBB42_v1.2_T0: temp=30.9 raspberry_pi: temp=32.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417717 bytes_read=24327236 bytes_retransmit=9 bytes_invalid=0 send_seq=69615 receive_seq=69615 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999909 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3370.936 memavail=1410152 print_time=70471.322 buffer_time=0.000 print_stall=0 extruder: target=220 temp=96.7 pwm=1.000
Stats 70467.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421159 bytes_read=7897527 bytes_retransmit=9 bytes_invalid=0 send_seq=69872 receive_seq=69872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000013 bytes_write=418194 bytes_read=1289612 bytes_retransmit=0 bytes_invalid=0 send_seq=69666 receive_seq=69666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998316 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419677 bytes_read=7667076 bytes_retransmit=9 bytes_invalid=0 send_seq=69765 receive_seq=69765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999517 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=30.7 raspberry_pi: temp=32.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417723 bytes_read=24327592 bytes_retransmit=9 bytes_invalid=0 send_seq=69616 receive_seq=69616 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999905 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3370.994 memavail=1410404 print_time=70472.322 buffer_time=0.000 print_stall=0 extruder: target=220 temp=105.0 pwm=1.000
Stats 70468.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421165 bytes_read=7897630 bytes_retransmit=9 bytes_invalid=0 send_seq=69873 receive_seq=69873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000013 bytes_write=418200 bytes_read=1289628 bytes_retransmit=0 bytes_invalid=0 send_seq=69667 receive_seq=69667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998327 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419711 bytes_read=7667207 bytes_retransmit=9 bytes_invalid=0 send_seq=69768 receive_seq=69768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999526 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=30.8 raspberry_pi: temp=34.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417729 bytes_read=24327948 bytes_retransmit=9 bytes_invalid=0 send_seq=69617 receive_seq=69617 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999918 coil_temp=25.3 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.08 cputime=3371.054 memavail=1410404 print_time=70473.324 buffer_time=0.000 print_stall=0 extruder: target=220 temp=111.0 pwm=1.000
Stats 70469.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421171 bytes_read=7897733 bytes_retransmit=9 bytes_invalid=0 send_seq=69874 receive_seq=69874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999666 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=418206 bytes_read=1289657 bytes_retransmit=0 bytes_invalid=0 send_seq=69668 receive_seq=69668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998356 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419731 bytes_read=7667351 bytes_retransmit=9 bytes_invalid=0 send_seq=69770 receive_seq=69770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999474 adj=63999529 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=31.0 raspberry_pi: temp=32.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417735 bytes_read=24328304 bytes_retransmit=9 bytes_invalid=0 send_seq=69618 receive_seq=69618 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999924 coil_temp=25.3 refs=0 mcu_temp=23.94 supply_voltage=3.013 sysload=0.07 cputime=3371.112 memavail=1410404 print_time=70474.324 buffer_time=0.000 print_stall=0 extruder: target=220 temp=116.8 pwm=1.000
Stats 70470.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421177 bytes_read=7897865 bytes_retransmit=9 bytes_invalid=0 send_seq=69875 receive_seq=69875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999669 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=418212 bytes_read=1289673 bytes_retransmit=0 bytes_invalid=0 send_seq=69669 receive_seq=69669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998373 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419765 bytes_read=7667529 bytes_retransmit=9 bytes_invalid=0 send_seq=69773 receive_seq=69773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999475 adj=63999528 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.0 raspberry_pi: temp=32.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417741 bytes_read=24328660 bytes_retransmit=9 bytes_invalid=0 send_seq=69619 receive_seq=69619 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999924 coil_temp=25.3 refs=0 mcu_temp=23.93 supply_voltage=3.013 sysload=0.07 cputime=3371.171 memavail=1410404 print_time=70475.325 buffer_time=0.000 print_stall=0 extruder: target=220 temp=124.6 pwm=1.000
Stats 70471.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421183 bytes_read=7897968 bytes_retransmit=9 bytes_invalid=0 send_seq=69876 receive_seq=69876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999670 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=418218 bytes_read=1289689 bytes_retransmit=0 bytes_invalid=0 send_seq=69670 receive_seq=69670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998383 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419810 bytes_read=7667692 bytes_retransmit=9 bytes_invalid=0 send_seq=69776 receive_seq=69776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999529 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=31.1 raspberry_pi: temp=32.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417747 bytes_read=24329016 bytes_retransmit=9 bytes_invalid=0 send_seq=69620 receive_seq=69620 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999915 coil_temp=25.3 refs=0 mcu_temp=23.93 supply_voltage=3.013 sysload=0.07 cputime=3371.231 memavail=1410404 print_time=70476.325 buffer_time=0.000 print_stall=0 extruder: target=220 temp=130.0 pwm=1.000
Stats 70472.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421189 bytes_read=7898085 bytes_retransmit=9 bytes_invalid=0 send_seq=69877 receive_seq=69877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999670 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=418224 bytes_read=1289705 bytes_retransmit=0 bytes_invalid=0 send_seq=69671 receive_seq=69671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998397 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419844 bytes_read=7667841 bytes_retransmit=9 bytes_invalid=0 send_seq=69779 receive_seq=69779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999476 adj=63999550 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.0 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417753 bytes_read=24329372 bytes_retransmit=9 bytes_invalid=0 send_seq=69621 receive_seq=69621 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999913 coil_temp=25.3 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.07 cputime=3371.289 memavail=1410404 print_time=70477.326 buffer_time=0.000 print_stall=0 extruder: target=220 temp=135.3 pwm=1.000
Stats 70473.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421195 bytes_read=7898217 bytes_retransmit=9 bytes_invalid=0 send_seq=69878 receive_seq=69878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999670 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=418230 bytes_read=1289721 bytes_retransmit=0 bytes_invalid=0 send_seq=69672 receive_seq=69672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998409 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419878 bytes_read=7668019 bytes_retransmit=9 bytes_invalid=0 send_seq=69782 receive_seq=69782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999569 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417759 bytes_read=24329728 bytes_retransmit=9 bytes_invalid=0 send_seq=69622 receive_seq=69622 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999916 coil_temp=25.3 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.07 cputime=3371.350 memavail=1410404 print_time=70478.327 buffer_time=0.000 print_stall=0 extruder: target=220 temp=142.1 pwm=1.000
Stats 70474.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421201 bytes_read=7898320 bytes_retransmit=9 bytes_invalid=0 send_seq=69879 receive_seq=69879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418236 bytes_read=1289750 bytes_retransmit=0 bytes_invalid=0 send_seq=69673 receive_seq=69673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998413 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419912 bytes_read=7668168 bytes_retransmit=9 bytes_invalid=0 send_seq=69785 receive_seq=69785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999570 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417765 bytes_read=24330084 bytes_retransmit=9 bytes_invalid=0 send_seq=69623 receive_seq=69623 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999915 coil_temp=25.3 refs=0 mcu_temp=23.89 supply_voltage=3.013 sysload=0.06 cputime=3371.408 memavail=1409688 print_time=70479.327 buffer_time=0.000 print_stall=0 extruder: target=220 temp=147.2 pwm=1.000
Stats 70475.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421207 bytes_read=7898423 bytes_retransmit=9 bytes_invalid=0 send_seq=69880 receive_seq=69880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418242 bytes_read=1289766 bytes_retransmit=0 bytes_invalid=0 send_seq=69674 receive_seq=69674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998419 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419962 bytes_read=7668322 bytes_retransmit=9 bytes_invalid=0 send_seq=69789 receive_seq=69789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999572 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.1 raspberry_pi: temp=31.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417771 bytes_read=24330440 bytes_retransmit=9 bytes_invalid=0 send_seq=69624 receive_seq=69624 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999926 coil_temp=25.3 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.06 cputime=3371.466 memavail=1409688 print_time=70480.328 buffer_time=0.000 print_stall=0 extruder: target=220 temp=152.3 pwm=1.000
Stats 70476.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421213 bytes_read=7898555 bytes_retransmit=9 bytes_invalid=0 send_seq=69881 receive_seq=69881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999673 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418254 bytes_read=1289798 bytes_retransmit=0 bytes_invalid=0 send_seq=69676 receive_seq=69676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998421 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=419996 bytes_read=7668514 bytes_retransmit=9 bytes_invalid=0 send_seq=69792 receive_seq=69792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999580 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417777 bytes_read=24330796 bytes_retransmit=9 bytes_invalid=0 send_seq=69625 receive_seq=69625 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999921 coil_temp=25.3 refs=0 mcu_temp=23.88 supply_voltage=3.013 sysload=0.06 cputime=3371.526 memavail=1409696 print_time=70481.329 buffer_time=0.000 print_stall=0 extruder: target=220 temp=158.6 pwm=1.000
Stats 70477.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421219 bytes_read=7898672 bytes_retransmit=9 bytes_invalid=0 send_seq=69882 receive_seq=69882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418260 bytes_read=1289814 bytes_retransmit=0 bytes_invalid=0 send_seq=69677 receive_seq=69677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998439 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420030 bytes_read=7668663 bytes_retransmit=9 bytes_invalid=0 send_seq=69795 receive_seq=69795 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999585 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=31.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417783 bytes_read=24331152 bytes_retransmit=9 bytes_invalid=0 send_seq=69626 receive_seq=69626 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999917 coil_temp=25.3 refs=0 mcu_temp=23.89 supply_voltage=3.013 sysload=0.06 cputime=3371.561 memavail=1410188 print_time=70482.330 buffer_time=0.000 print_stall=0 extruder: target=220 temp=163.5 pwm=1.000
Stats 70478.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421225 bytes_read=7898789 bytes_retransmit=9 bytes_invalid=0 send_seq=69883 receive_seq=69883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418266 bytes_read=1289830 bytes_retransmit=0 bytes_invalid=0 send_seq=69678 receive_seq=69678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998411 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420072 bytes_read=7668827 bytes_retransmit=9 bytes_invalid=0 send_seq=69799 receive_seq=69799 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999649 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=31.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417789 bytes_read=24331508 bytes_retransmit=9 bytes_invalid=0 send_seq=69627 receive_seq=69627 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999936 coil_temp=25.3 refs=0 mcu_temp=23.89 supply_voltage=3.013 sysload=0.06 cputime=3371.587 memavail=1410188 print_time=70483.331 buffer_time=0.000 print_stall=0 extruder: target=220 temp=167.7 pwm=1.000
Stats 70479.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421231 bytes_read=7898905 bytes_retransmit=9 bytes_invalid=0 send_seq=69884 receive_seq=69884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999661 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=418272 bytes_read=1289859 bytes_retransmit=0 bytes_invalid=0 send_seq=69679 receive_seq=69679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998327 adj=49998394 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420122 bytes_read=7669010 bytes_retransmit=9 bytes_invalid=0 send_seq=69803 receive_seq=69803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999472 adj=63999640 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417795 bytes_read=24331864 bytes_retransmit=9 bytes_invalid=0 send_seq=69628 receive_seq=69628 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999928 coil_temp=25.4 refs=0 mcu_temp=23.89 supply_voltage=3.013 sysload=0.06 cputime=3371.611 memavail=1410188 print_time=70484.331 buffer_time=0.000 print_stall=0 extruder: target=220 temp=174.0 pwm=1.000
Stats 70480.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421237 bytes_read=7899001 bytes_retransmit=9 bytes_invalid=0 send_seq=69885 receive_seq=69885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=418278 bytes_read=1289875 bytes_retransmit=0 bytes_invalid=0 send_seq=69680 receive_seq=69680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998325 adj=49998366 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420156 bytes_read=7669159 bytes_retransmit=9 bytes_invalid=0 send_seq=69806 receive_seq=69806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999612 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417801 bytes_read=24332220 bytes_retransmit=9 bytes_invalid=0 send_seq=69629 receive_seq=69629 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999914 coil_temp=25.4 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.06 cputime=3371.638 memavail=1410188 print_time=70485.331 buffer_time=0.000 print_stall=0 extruder: target=220 temp=178.2 pwm=1.000
Stats 70481.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421243 bytes_read=7899116 bytes_retransmit=9 bytes_invalid=0 send_seq=69886 receive_seq=69886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999652 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=418284 bytes_read=1289891 bytes_retransmit=0 bytes_invalid=0 send_seq=69681 receive_seq=69681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998324 adj=49998362 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420190 bytes_read=7669322 bytes_retransmit=9 bytes_invalid=0 send_seq=69809 receive_seq=69809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999469 adj=63999604 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417807 bytes_read=24332576 bytes_retransmit=9 bytes_invalid=0 send_seq=69630 receive_seq=69630 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999909 coil_temp=25.4 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.06 cputime=3371.664 memavail=1409972 print_time=70486.332 buffer_time=0.000 print_stall=0 extruder: target=220 temp=182.6 pwm=1.000
Stats 70482.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421249 bytes_read=7899248 bytes_retransmit=9 bytes_invalid=0 send_seq=69887 receive_seq=69887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999655 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=418290 bytes_read=1289907 bytes_retransmit=0 bytes_invalid=0 send_seq=69682 receive_seq=69682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998379 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420224 bytes_read=7669500 bytes_retransmit=9 bytes_invalid=0 send_seq=69812 receive_seq=69812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999611 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417813 bytes_read=24332932 bytes_retransmit=9 bytes_invalid=0 send_seq=69631 receive_seq=69631 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999916 coil_temp=25.4 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.06 cputime=3371.716 memavail=1409972 print_time=70487.333 buffer_time=0.000 print_stall=0 extruder: target=220 temp=188.1 pwm=1.000
Stats 70483.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421255 bytes_read=7899351 bytes_retransmit=9 bytes_invalid=0 send_seq=69888 receive_seq=69888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999655 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=418296 bytes_read=1289923 bytes_retransmit=0 bytes_invalid=0 send_seq=69683 receive_seq=69683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998450 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420274 bytes_read=7669654 bytes_retransmit=9 bytes_invalid=0 send_seq=69816 receive_seq=69816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999607 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.4 raspberry_pi: temp=32.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417825 bytes_read=24333304 bytes_retransmit=9 bytes_invalid=0 send_seq=69633 receive_seq=69633 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31999899 coil_temp=25.4 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.06 cputime=3371.776 memavail=1409972 print_time=70488.333 buffer_time=0.000 print_stall=0 extruder: target=220 temp=192.4 pwm=1.000
Stats 70484.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421261 bytes_read=7899468 bytes_retransmit=9 bytes_invalid=0 send_seq=69889 receive_seq=69889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418302 bytes_read=1289952 bytes_retransmit=0 bytes_invalid=0 send_seq=69684 receive_seq=69684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998473 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420308 bytes_read=7669803 bytes_retransmit=9 bytes_invalid=0 send_seq=69819 receive_seq=69819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999602 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417831 bytes_read=24333660 bytes_retransmit=9 bytes_invalid=0 send_seq=69634 receive_seq=69634 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=32000042 coil_temp=25.4 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.05 cputime=3371.834 memavail=1409708 print_time=70489.334 buffer_time=0.000 print_stall=0 extruder: target=220 temp=196.1 pwm=1.000
Stats 70485.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421267 bytes_read=7899586 bytes_retransmit=9 bytes_invalid=0 send_seq=69890 receive_seq=69890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418308 bytes_read=1289968 bytes_retransmit=0 bytes_invalid=0 send_seq=69685 receive_seq=69685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998470 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420342 bytes_read=7669981 bytes_retransmit=9 bytes_invalid=0 send_seq=69822 receive_seq=69822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999598 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417837 bytes_read=24334016 bytes_retransmit=9 bytes_invalid=0 send_seq=69635 receive_seq=69635 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=32000019 coil_temp=25.4 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.05 cputime=3371.891 memavail=1409708 print_time=70490.334 buffer_time=0.000 print_stall=0 extruder: target=220 temp=201.0 pwm=1.000
Stats 70486.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421273 bytes_read=7899689 bytes_retransmit=9 bytes_invalid=0 send_seq=69891 receive_seq=69891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999657 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418314 bytes_read=1289984 bytes_retransmit=0 bytes_invalid=0 send_seq=69686 receive_seq=69686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998473 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420376 bytes_read=7670144 bytes_retransmit=9 bytes_invalid=0 send_seq=69825 receive_seq=69825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999602 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417843 bytes_read=24334372 bytes_retransmit=9 bytes_invalid=0 send_seq=69636 receive_seq=69636 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=32000000 coil_temp=25.4 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.05 cputime=3371.950 memavail=1409760 print_time=70491.335 buffer_time=0.000 print_stall=0 extruder: target=220 temp=205.1 pwm=1.000
Stats 70487.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421279 bytes_read=7899820 bytes_retransmit=9 bytes_invalid=0 send_seq=69892 receive_seq=69892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999657 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418320 bytes_read=1290000 bytes_retransmit=0 bytes_invalid=0 send_seq=69687 receive_seq=69687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998491 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420426 bytes_read=7670298 bytes_retransmit=9 bytes_invalid=0 send_seq=69829 receive_seq=69829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999595 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.6 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417849 bytes_read=24334728 bytes_retransmit=9 bytes_invalid=0 send_seq=69637 receive_seq=69637 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31999984 coil_temp=25.4 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.05 cputime=3372.010 memavail=1409760 print_time=70492.336 buffer_time=0.000 print_stall=0 extruder: target=220 temp=208.8 pwm=1.000
Stats 70488.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421285 bytes_read=7899938 bytes_retransmit=9 bytes_invalid=0 send_seq=69893 receive_seq=69893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418326 bytes_read=1290016 bytes_retransmit=0 bytes_invalid=0 send_seq=69688 receive_seq=69688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998501 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420492 bytes_read=7670486 bytes_retransmit=9 bytes_invalid=0 send_seq=69834 receive_seq=69834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999604 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=31.6 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417855 bytes_read=24335084 bytes_retransmit=9 bytes_invalid=0 send_seq=69638 receive_seq=69638 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31999968 coil_temp=25.4 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.05 cputime=3372.072 memavail=1409760 print_time=70493.338 buffer_time=0.000 print_stall=0 extruder: target=220 temp=213.7 pwm=0.819
Stats 70489.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421291 bytes_read=7900041 bytes_retransmit=9 bytes_invalid=0 send_seq=69894 receive_seq=69894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999654 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=418332 bytes_read=1290045 bytes_retransmit=0 bytes_invalid=0 send_seq=69689 receive_seq=69689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998550 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420558 bytes_read=7670645 bytes_retransmit=9 bytes_invalid=0 send_seq=69839 receive_seq=69839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999604 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417861 bytes_read=24335440 bytes_retransmit=9 bytes_invalid=0 send_seq=69639 receive_seq=69639 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999955 coil_temp=25.4 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.13 cputime=3372.134 memavail=1409760 print_time=70494.342 buffer_time=0.000 print_stall=0 extruder: target=220 temp=216.5 pwm=0.649
Heater extruder within range of 220.000
Stats 70490.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421297 bytes_read=7900158 bytes_retransmit=9 bytes_invalid=0 send_seq=69895 receive_seq=69895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=418338 bytes_read=1290061 bytes_retransmit=0 bytes_invalid=0 send_seq=69690 receive_seq=69690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998589 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=420640 bytes_read=7670809 bytes_retransmit=9 bytes_invalid=0 send_seq=69845 receive_seq=69845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999610 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=32.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417867 bytes_read=24335796 bytes_retransmit=9 bytes_invalid=0 send_seq=69640 receive_seq=69640 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999954 coil_temp=25.4 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.13 cputime=3372.197 memavail=1409760 print_time=70495.345 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.0 pwm=0.416
Stats 70491.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421303 bytes_read=7900276 bytes_retransmit=9 bytes_invalid=0 send_seq=69896 receive_seq=69896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=418344 bytes_read=1290077 bytes_retransmit=0 bytes_invalid=0 send_seq=69691 receive_seq=69691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998569 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=420690 bytes_read=7671006 bytes_retransmit=9 bytes_invalid=0 send_seq=69849 receive_seq=69849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999472 adj=63999600 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417873 bytes_read=24336136 bytes_retransmit=9 bytes_invalid=0 send_seq=69641 receive_seq=69641 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999937 coil_temp=25.4 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.13 cputime=3372.258 memavail=1409760 print_time=70496.348 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.2 pwm=0.652
Stats 70492.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421309 bytes_read=7900393 bytes_retransmit=9 bytes_invalid=0 send_seq=69897 receive_seq=69897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=418350 bytes_read=1290093 bytes_retransmit=0 bytes_invalid=0 send_seq=69692 receive_seq=69692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998540 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=420751 bytes_read=7671160 bytes_retransmit=9 bytes_invalid=0 send_seq=69853 receive_seq=69853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999476 adj=63999590 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=32.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417879 bytes_read=24336492 bytes_retransmit=9 bytes_invalid=0 send_seq=69642 receive_seq=69642 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999930 coil_temp=25.5 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.13 cputime=3372.318 memavail=1409776 print_time=70497.353 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.2 pwm=0.482
Stats 70493.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421315 bytes_read=7900510 bytes_retransmit=9 bytes_invalid=0 send_seq=69898 receive_seq=69898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=418356 bytes_read=1290109 bytes_retransmit=0 bytes_invalid=0 send_seq=69693 receive_seq=69693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998353 adj=49998539 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=420833 bytes_read=7671324 bytes_retransmit=9 bytes_invalid=0 send_seq=69859 receive_seq=69859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999476 adj=63999655 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417885 bytes_read=24336848 bytes_retransmit=9 bytes_invalid=0 send_seq=69643 receive_seq=69643 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999931 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.13 cputime=3372.379 memavail=1409776 print_time=70498.353 buffer_time=0.000 print_stall=0 extruder: target=220 temp=221.3 pwm=0.277
RatOS | TEMPERATURE_WAIT:: Temperature for toolhead T0 reached.
RatOS:: Loading filament into hotend..
Stats 70494.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421321 bytes_read=7900628 bytes_retransmit=9 bytes_invalid=0 send_seq=69899 receive_seq=69899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999660 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000025 bytes_write=418362 bytes_read=1290138 bytes_retransmit=0 bytes_invalid=0 send_seq=69694 receive_seq=69694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998349 adj=49998575 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=422301 bytes_read=7671627 bytes_retransmit=9 bytes_invalid=0 send_seq=69887 receive_seq=69887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999620 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.2 raspberry_pi: temp=32.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417891 bytes_read=24337204 bytes_retransmit=9 bytes_invalid=0 send_seq=69644 receive_seq=69644 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999915 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.28 cputime=3372.461 memavail=1412332 print_time=70499.890 buffer_time=0.073 print_stall=0 extruder: target=220 temp=220.8 pwm=0.412
RatOS:: Filament loaded into hotend.
RatOS:: Loading filament into nozzle... Please wait!
Stats 70495.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421327 bytes_read=7900731 bytes_retransmit=9 bytes_invalid=0 send_seq=69900 receive_seq=69900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999654 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000025 bytes_write=418368 bytes_read=1290154 bytes_retransmit=0 bytes_invalid=0 send_seq=69695 receive_seq=69695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998490 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=422650 bytes_read=7671811 bytes_retransmit=9 bytes_invalid=0 send_seq=69897 receive_seq=69897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999475 adj=63999650 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417897 bytes_read=24337560 bytes_retransmit=9 bytes_invalid=0 send_seq=69645 receive_seq=69645 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999915 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.28 cputime=3372.505 memavail=1412332 print_time=70504.704 buffer_time=3.886 print_stall=0 extruder: target=220 temp=219.1 pwm=0.810
Stats 70496.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421333 bytes_read=7900863 bytes_retransmit=9 bytes_invalid=0 send_seq=69901 receive_seq=69901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000025 bytes_write=418374 bytes_read=1290170 bytes_retransmit=0 bytes_invalid=0 send_seq=69696 receive_seq=69696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998417 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=422711 bytes_read=7671980 bytes_retransmit=9 bytes_invalid=0 send_seq=69901 receive_seq=69901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999476 adj=63999596 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=31.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417903 bytes_read=24337916 bytes_retransmit=9 bytes_invalid=0 send_seq=69646 receive_seq=69646 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999938 coil_temp=25.5 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.28 cputime=3372.531 memavail=1412332 print_time=70504.704 buffer_time=2.886 print_stall=0 extruder: target=220 temp=219.8 pwm=0.575
RatOS:: Filament loaded into nozzle!
Stats 70497.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421339 bytes_read=7900980 bytes_retransmit=9 bytes_invalid=0 send_seq=69902 receive_seq=69902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000025 bytes_write=418380 bytes_read=1290186 bytes_retransmit=0 bytes_invalid=0 send_seq=69697 receive_seq=69697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998377 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=422776 bytes_read=7672168 bytes_retransmit=9 bytes_invalid=0 send_seq=69906 receive_seq=69906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999475 adj=63999590 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417909 bytes_read=24338272 bytes_retransmit=9 bytes_invalid=0 send_seq=69647 receive_seq=69647 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999942 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.28 cputime=3372.567 memavail=1412336 print_time=70504.704 buffer_time=1.886 print_stall=0 extruder: target=220 temp=221.4 pwm=0.227
Stats 70498.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421345 bytes_read=7901083 bytes_retransmit=9 bytes_invalid=0 send_seq=69903 receive_seq=69903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000025 bytes_write=418386 bytes_read=1290202 bytes_retransmit=0 bytes_invalid=0 send_seq=69698 receive_seq=69698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998354 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=422852 bytes_read=7672327 bytes_retransmit=9 bytes_invalid=0 send_seq=69911 receive_seq=69911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999594 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417915 bytes_read=24338628 bytes_retransmit=9 bytes_invalid=0 send_seq=69648 receive_seq=69648 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999937 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.28 cputime=3372.594 memavail=1412344 print_time=70504.704 buffer_time=0.886 print_stall=0 extruder: target=220 temp=219.8 pwm=0.639
RatOS:: Heating extruder to 220C... Please wait.
RatOS | TEMPERATURE_WAIT:: Waiting for sensor: extruder, MINIMUM: 220
RatOS:: please wait...
Stats 70499.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421351 bytes_read=7901215 bytes_retransmit=9 bytes_invalid=0 send_seq=69904 receive_seq=69904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999646 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=418392 bytes_read=1290231 bytes_retransmit=0 bytes_invalid=0 send_seq=69699 receive_seq=69699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998336 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=422937 bytes_read=7672501 bytes_retransmit=9 bytes_invalid=0 send_seq=69917 receive_seq=69917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999595 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=31.9 raspberry_pi: temp=34.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417921 bytes_read=24338984 bytes_retransmit=9 bytes_invalid=0 send_seq=69649 receive_seq=69649 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999934 coil_temp=25.5 refs=0 mcu_temp=23.91 supply_voltage=3.013 sysload=0.26 cputime=3372.672 memavail=1412344 print_time=70505.006 buffer_time=0.187 print_stall=0 extruder: target=220 temp=219.0 pwm=0.749
RatOS | TEMPERATURE_WAIT:: Temperature for toolhead T0 reached.
Stats 70500.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421357 bytes_read=7901318 bytes_retransmit=9 bytes_invalid=0 send_seq=69905 receive_seq=69905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999645 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=418398 bytes_read=1290247 bytes_retransmit=0 bytes_invalid=0 send_seq=69700 receive_seq=69700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998353 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=423018 bytes_read=7672694 bytes_retransmit=9 bytes_invalid=0 send_seq=69923 receive_seq=69923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999473 adj=63999603 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=32.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417927 bytes_read=24339340 bytes_retransmit=9 bytes_invalid=0 send_seq=69650 receive_seq=69650 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999935 coil_temp=25.6 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.26 cputime=3372.734 memavail=1412344 print_time=70509.010 buffer_time=3.191 print_stall=0 extruder: target=220 temp=221.8 pwm=0.050
Stats 70501.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421363 bytes_read=7901421 bytes_retransmit=9 bytes_invalid=0 send_seq=69906 receive_seq=69906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=418404 bytes_read=1290263 bytes_retransmit=0 bytes_invalid=0 send_seq=69701 receive_seq=69701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998408 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000026 mcu_task_stddev=0.000032 bytes_write=423093 bytes_read=7672853 bytes_retransmit=9 bytes_invalid=0 send_seq=69928 receive_seq=69928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999601 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.0 raspberry_pi: temp=32.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417933 bytes_read=24339696 bytes_retransmit=9 bytes_invalid=0 send_seq=69651 receive_seq=69651 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999932 coil_temp=25.6 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.26 cputime=3372.793 memavail=1412344 print_time=70509.010 buffer_time=2.190 print_stall=0 extruder: target=220 temp=221.1 pwm=0.320
Stats 70502.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421369 bytes_read=7901567 bytes_retransmit=9 bytes_invalid=0 send_seq=69907 receive_seq=69907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=418410 bytes_read=1290279 bytes_retransmit=0 bytes_invalid=0 send_seq=69702 receive_seq=69702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998430 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=424233 bytes_read=7673112 bytes_retransmit=9 bytes_invalid=0 send_seq=69950 receive_seq=69950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999595 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417939 bytes_read=24340052 bytes_retransmit=9 bytes_invalid=0 send_seq=69652 receive_seq=69652 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999930 coil_temp=25.6 refs=0 mcu_temp=23.90 supply_voltage=3.013 sysload=0.26 cputime=3372.882 memavail=1412344 print_time=70514.284 buffer_time=6.464 print_stall=0 extruder: target=220 temp=219.0 pwm=0.765
Stats 70503.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421375 bytes_read=7901666 bytes_retransmit=9 bytes_invalid=0 send_seq=69908 receive_seq=69908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=418416 bytes_read=1290295 bytes_retransmit=0 bytes_invalid=0 send_seq=69703 receive_seq=69703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998454 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=424294 bytes_read=7673295 bytes_retransmit=9 bytes_invalid=0 send_seq=69954 receive_seq=69954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999477 adj=63999617 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417945 bytes_read=24340408 bytes_retransmit=9 bytes_invalid=0 send_seq=69653 receive_seq=69653 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999934 coil_temp=25.6 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.26 cputime=3372.941 memavail=1412344 print_time=70514.284 buffer_time=5.464 print_stall=0 extruder: target=220 temp=221.3 pwm=0.129
Stats 70504.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421381 bytes_read=7901762 bytes_retransmit=9 bytes_invalid=0 send_seq=69909 receive_seq=69909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418422 bytes_read=1290324 bytes_retransmit=0 bytes_invalid=0 send_seq=69704 receive_seq=69704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998474 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=424351 bytes_read=7673449 bytes_retransmit=9 bytes_invalid=0 send_seq=69958 receive_seq=69958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999615 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.1 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417951 bytes_read=24340764 bytes_retransmit=9 bytes_invalid=0 send_seq=69654 receive_seq=69654 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999935 coil_temp=25.6 refs=0 mcu_temp=23.92 supply_voltage=3.013 sysload=0.24 cputime=3372.998 memavail=1412092 print_time=70514.284 buffer_time=4.464 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Stats 70505.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421387 bytes_read=7901894 bytes_retransmit=9 bytes_invalid=0 send_seq=69910 receive_seq=69910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418428 bytes_read=1290340 bytes_retransmit=0 bytes_invalid=0 send_seq=69705 receive_seq=69705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998350 adj=49998477 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=424432 bytes_read=7673613 bytes_retransmit=9 bytes_invalid=0 send_seq=69964 receive_seq=69964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999478 adj=63999615 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=32.1 raspberry_pi: temp=33.1  heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417957 bytes_read=24341120 bytes_retransmit=9 bytes_invalid=0 send_seq=69655 receive_seq=69655 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999934 coil_temp=25.6 refs=0 mcu_temp=23.94 supply_voltage=3.013 sysload=0.24 cputime=3373.058 memavail=1412092 print_time=70514.284 buffer_time=3.464 print_stall=0 extruder: target=220 temp=219.2 pwm=0.764
Stats 70506.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421393 bytes_read=7901997 bytes_retransmit=9 bytes_invalid=0 send_seq=69911 receive_seq=69911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418434 bytes_read=1290356 bytes_retransmit=0 bytes_invalid=0 send_seq=69706 receive_seq=69706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998351 adj=49998483 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=424514 bytes_read=7673806 bytes_retransmit=9 bytes_invalid=0 send_seq=69970 receive_seq=69970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999479 adj=63999616 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417963 bytes_read=24341476 bytes_retransmit=9 bytes_invalid=0 send_seq=69656 receive_seq=69656 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999933 coil_temp=25.7 refs=0 mcu_temp=23.94 supply_voltage=3.013 sysload=0.24 cputime=3373.119 memavail=1411868 print_time=70514.284 buffer_time=2.464 print_stall=0 extruder: target=220 temp=220.5 pwm=0.282
Starting SD card print (position 0)
RatOS:: First print coordinates X:-1.0 Y:-1.0
RatOS:: Homing X Y Z 
Stats 70507.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421399 bytes_read=7902114 bytes_retransmit=9 bytes_invalid=0 send_seq=69912 receive_seq=69912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999655 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418440 bytes_read=1290372 bytes_retransmit=0 bytes_invalid=0 send_seq=69707 receive_seq=69707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998352 adj=49998487 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000024 bytes_write=426882 bytes_read=7674180 bytes_retransmit=9 bytes_invalid=0 send_seq=70013 receive_seq=70013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=63999479 adj=63999616 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417969 bytes_read=24341832 bytes_retransmit=9 bytes_invalid=0 send_seq=69657 receive_seq=69657 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999930 coil_temp=25.7 refs=0 mcu_temp=23.95 supply_voltage=3.013 sysload=0.24 cputime=3373.464 memavail=1411616 print_time=70541.831 buffer_time=29.010 print_stall=0 extruder: target=220 temp=222.6 pwm=0.000
Stats 70508.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421405 bytes_read=7902246 bytes_retransmit=9 bytes_invalid=0 send_seq=69913 receive_seq=69913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999651 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418446 bytes_read=1290388 bytes_retransmit=0 bytes_invalid=0 send_seq=69708 receive_seq=69708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998441 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000024 bytes_write=427006 bytes_read=7674339 bytes_retransmit=9 bytes_invalid=0 send_seq=70018 receive_seq=70018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999599 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.1 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417975 bytes_read=24342188 bytes_retransmit=9 bytes_invalid=0 send_seq=69658 receive_seq=69658 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999932 coil_temp=25.7 refs=0 mcu_temp=23.96 supply_voltage=3.013 sysload=0.24 cputime=3373.490 memavail=1411628 print_time=70541.831 buffer_time=28.010 print_stall=0 extruder: target=220 temp=220.2 pwm=0.545
Stats 70509.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421411 bytes_read=7902349 bytes_retransmit=9 bytes_invalid=0 send_seq=69914 receive_seq=69914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=418452 bytes_read=1290417 bytes_retransmit=0 bytes_invalid=0 send_seq=69709 receive_seq=69709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998435 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000024 bytes_write=427088 bytes_read=7674532 bytes_retransmit=9 bytes_invalid=0 send_seq=70024 receive_seq=70024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999475 adj=63999596 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417981 bytes_read=24342544 bytes_retransmit=9 bytes_invalid=0 send_seq=69659 receive_seq=69659 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999932 coil_temp=25.7 refs=0 mcu_temp=23.99 supply_voltage=3.013 sysload=0.22 cputime=3373.517 memavail=1411404 print_time=70541.831 buffer_time=27.010 print_stall=0 extruder: target=220 temp=220.1 pwm=0.411
Stats 70510.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421417 bytes_read=7902452 bytes_retransmit=9 bytes_invalid=0 send_seq=69915 receive_seq=69915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999644 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=418458 bytes_read=1290433 bytes_retransmit=0 bytes_invalid=0 send_seq=69710 receive_seq=69710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998430 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000024 bytes_write=427176 bytes_read=7674696 bytes_retransmit=9 bytes_invalid=0 send_seq=70030 receive_seq=70030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999473 adj=63999596 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417987 bytes_read=24342900 bytes_retransmit=9 bytes_invalid=0 send_seq=69660 receive_seq=69660 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999934 coil_temp=25.7 refs=0 mcu_temp=24.00 supply_voltage=3.013 sysload=0.22 cputime=3373.543 memavail=1411404 print_time=70541.831 buffer_time=26.009 print_stall=0 extruder: target=220 temp=222.6 pwm=0.000
Stats 70511.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421423 bytes_read=7902584 bytes_retransmit=9 bytes_invalid=0 send_seq=69916 receive_seq=69916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999640 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=418464 bytes_read=1290449 bytes_retransmit=0 bytes_invalid=0 send_seq=69711 receive_seq=69711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998424 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000024 bytes_write=427241 bytes_read=7674855 bytes_retransmit=9 bytes_invalid=0 send_seq=70035 receive_seq=70035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999595 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=22.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417993 bytes_read=24343256 bytes_retransmit=9 bytes_invalid=0 send_seq=69661 receive_seq=69661 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999933 coil_temp=25.7 refs=0 mcu_temp=24.02 supply_voltage=3.013 sysload=0.22 cputime=3373.571 memavail=1407140 print_time=70541.831 buffer_time=25.009 print_stall=0 extruder: target=220 temp=221.0 pwm=0.312
Stats 70512.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421429 bytes_read=7902701 bytes_retransmit=9 bytes_invalid=0 send_seq=69917 receive_seq=69917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999638 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=418470 bytes_read=1290465 bytes_retransmit=0 bytes_invalid=0 send_seq=69712 receive_seq=69712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998419 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000026 mcu_task_stddev=0.000031 bytes_write=427323 bytes_read=7675063 bytes_retransmit=9 bytes_invalid=0 send_seq=70041 receive_seq=70041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999594 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417999 bytes_read=24343612 bytes_retransmit=9 bytes_invalid=0 send_seq=69662 receive_seq=69662 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999934 coil_temp=25.7 refs=0 mcu_temp=24.02 supply_voltage=3.014 sysload=0.22 cputime=3373.606 memavail=1412672 print_time=70541.831 buffer_time=24.008 print_stall=0 extruder: target=220 temp=219.3 pwm=0.593
Stats 70513.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421435 bytes_read=7902804 bytes_retransmit=9 bytes_invalid=0 send_seq=69918 receive_seq=69918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999642 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=418476 bytes_read=1290481 bytes_retransmit=0 bytes_invalid=0 send_seq=69713 receive_seq=69713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998412 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000026 mcu_task_stddev=0.000031 bytes_write=427401 bytes_read=7675227 bytes_retransmit=9 bytes_invalid=0 send_seq=70047 receive_seq=70047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999592 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418005 bytes_read=24343968 bytes_retransmit=9 bytes_invalid=0 send_seq=69663 receive_seq=69663 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999933 coil_temp=25.8 refs=0 mcu_temp=24.02 supply_voltage=3.013 sysload=0.22 cputime=3373.664 memavail=1412676 print_time=70541.831 buffer_time=23.008 print_stall=0 extruder: target=220 temp=222.0 pwm=0.000
Stats 70514.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421441 bytes_read=7902936 bytes_retransmit=9 bytes_invalid=0 send_seq=69919 receive_seq=69919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418482 bytes_read=1290510 bytes_retransmit=0 bytes_invalid=0 send_seq=69714 receive_seq=69714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998414 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000026 mcu_task_stddev=0.000031 bytes_write=427450 bytes_read=7675381 bytes_retransmit=9 bytes_invalid=0 send_seq=70051 receive_seq=70051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999589 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418011 bytes_read=24344324 bytes_retransmit=9 bytes_invalid=0 send_seq=69664 receive_seq=69664 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999933 coil_temp=25.8 refs=0 mcu_temp=24.04 supply_voltage=3.013 sysload=0.20 cputime=3373.724 memavail=1412676 print_time=70541.831 buffer_time=22.007 print_stall=0 extruder: target=220 temp=221.3 pwm=0.168
Stats 70515.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421447 bytes_read=7903039 bytes_retransmit=9 bytes_invalid=0 send_seq=69920 receive_seq=69920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418488 bytes_read=1290526 bytes_retransmit=0 bytes_invalid=0 send_seq=69715 receive_seq=69715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998413 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000026 mcu_task_stddev=0.000031 bytes_write=427532 bytes_read=7675574 bytes_retransmit=9 bytes_invalid=0 send_seq=70057 receive_seq=70057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999585 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418017 bytes_read=24344680 bytes_retransmit=9 bytes_invalid=0 send_seq=69665 receive_seq=69665 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999932 coil_temp=25.9 refs=0 mcu_temp=24.05 supply_voltage=3.013 sysload=0.20 cputime=3373.784 memavail=1412680 print_time=70541.831 buffer_time=21.006 print_stall=0 extruder: target=220 temp=218.7 pwm=0.699
Stats 70516.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421453 bytes_read=7903142 bytes_retransmit=9 bytes_invalid=0 send_seq=69921 receive_seq=69921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999651 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418494 bytes_read=1290542 bytes_retransmit=0 bytes_invalid=0 send_seq=69716 receive_seq=69716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998413 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000026 mcu_task_stddev=0.000031 bytes_write=427613 bytes_read=7675738 bytes_retransmit=9 bytes_invalid=0 send_seq=70063 receive_seq=70063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999586 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418023 bytes_read=24345036 bytes_retransmit=9 bytes_invalid=0 send_seq=69666 receive_seq=69666 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999932 coil_temp=25.9 refs=0 mcu_temp=24.05 supply_voltage=3.013 sysload=0.20 cputime=3373.844 memavail=1412456 print_time=70541.831 buffer_time=20.005 print_stall=0 extruder: target=220 temp=221.3 pwm=0.003
Stats 70517.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421459 bytes_read=7903288 bytes_retransmit=9 bytes_invalid=0 send_seq=69922 receive_seq=69922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999652 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418500 bytes_read=1290558 bytes_retransmit=0 bytes_invalid=0 send_seq=69717 receive_seq=69717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998411 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=427647 bytes_read=7675902 bytes_retransmit=9 bytes_invalid=0 send_seq=70066 receive_seq=70066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999585 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418029 bytes_read=24345392 bytes_retransmit=9 bytes_invalid=0 send_seq=69667 receive_seq=69667 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999934 coil_temp=25.9 refs=0 mcu_temp=24.05 supply_voltage=3.013 sysload=0.20 cputime=3373.901 memavail=1412456 print_time=70541.831 buffer_time=19.004 print_stall=0 extruder: target=220 temp=221.8 pwm=0.003
Stats 70518.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421465 bytes_read=7903391 bytes_retransmit=9 bytes_invalid=0 send_seq=69923 receive_seq=69923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999652 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000016 bytes_write=418506 bytes_read=1290574 bytes_retransmit=0 bytes_invalid=0 send_seq=69718 receive_seq=69718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998413 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=427744 bytes_read=7676100 bytes_retransmit=9 bytes_invalid=0 send_seq=70073 receive_seq=70073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999585 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418035 bytes_read=24345748 bytes_retransmit=9 bytes_invalid=0 send_seq=69668 receive_seq=69668 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999936 coil_temp=25.9 refs=0 mcu_temp=24.05 supply_voltage=3.013 sysload=0.20 cputime=3373.963 memavail=1412456 print_time=70541.831 buffer_time=18.003 print_stall=0 extruder: target=220 temp=218.6 pwm=0.766
Stats 70519.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421471 bytes_read=7903494 bytes_retransmit=9 bytes_invalid=0 send_seq=69924 receive_seq=69924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418512 bytes_read=1290603 bytes_retransmit=0 bytes_invalid=0 send_seq=69719 receive_seq=69719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998414 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=427825 bytes_read=7676264 bytes_retransmit=9 bytes_invalid=0 send_seq=70079 receive_seq=70079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999584 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418041 bytes_read=24346104 bytes_retransmit=9 bytes_invalid=0 send_seq=69669 receive_seq=69669 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999936 coil_temp=25.9 refs=0 mcu_temp=24.06 supply_voltage=3.013 sysload=0.18 cputime=3374.022 memavail=1412456 print_time=70541.831 buffer_time=17.002 print_stall=0 extruder: target=220 temp=220.3 pwm=0.239
Stats 70520.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421477 bytes_read=7903626 bytes_retransmit=9 bytes_invalid=0 send_seq=69925 receive_seq=69925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999666 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418518 bytes_read=1290619 bytes_retransmit=0 bytes_invalid=0 send_seq=69720 receive_seq=69720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998416 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=427874 bytes_read=7676418 bytes_retransmit=9 bytes_invalid=0 send_seq=70083 receive_seq=70083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999469 adj=63999581 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418047 bytes_read=24346460 bytes_retransmit=9 bytes_invalid=0 send_seq=69670 receive_seq=69670 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999939 coil_temp=25.9 refs=0 mcu_temp=24.06 supply_voltage=3.013 sysload=0.18 cputime=3374.081 memavail=1412456 print_time=70541.831 buffer_time=16.002 print_stall=0 extruder: target=220 temp=222.3 pwm=0.012
Stats 70521.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421483 bytes_read=7903729 bytes_retransmit=9 bytes_invalid=0 send_seq=69926 receive_seq=69926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999665 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418524 bytes_read=1290635 bytes_retransmit=0 bytes_invalid=0 send_seq=69721 receive_seq=69721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998412 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=427956 bytes_read=7676611 bytes_retransmit=9 bytes_invalid=0 send_seq=70089 receive_seq=70089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999468 adj=63999569 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.3 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418053 bytes_read=24346816 bytes_retransmit=9 bytes_invalid=0 send_seq=69671 receive_seq=69671 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999934 coil_temp=25.9 refs=0 mcu_temp=24.08 supply_voltage=3.013 sysload=0.18 cputime=3374.141 memavail=1412456 print_time=70541.831 buffer_time=15.001 print_stall=0 extruder: target=220 temp=218.7 pwm=0.748
Stats 70522.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421489 bytes_read=7903832 bytes_retransmit=9 bytes_invalid=0 send_seq=69927 receive_seq=69927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999664 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418530 bytes_read=1290651 bytes_retransmit=0 bytes_invalid=0 send_seq=69722 receive_seq=69722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998415 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428022 bytes_read=7676784 bytes_retransmit=9 bytes_invalid=0 send_seq=70094 receive_seq=70094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999467 adj=63999568 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418059 bytes_read=24347172 bytes_retransmit=9 bytes_invalid=0 send_seq=69672 receive_seq=69672 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999935 coil_temp=26.0 refs=0 mcu_temp=24.10 supply_voltage=3.013 sysload=0.18 cputime=3374.201 memavail=1412456 print_time=70541.831 buffer_time=14.001 print_stall=0 extruder: target=220 temp=219.6 pwm=0.430
Stats 70523.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421495 bytes_read=7903978 bytes_retransmit=9 bytes_invalid=0 send_seq=69928 receive_seq=69928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418536 bytes_read=1290667 bytes_retransmit=0 bytes_invalid=0 send_seq=69723 receive_seq=69723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998418 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428085 bytes_read=7676957 bytes_retransmit=9 bytes_invalid=0 send_seq=70099 receive_seq=70099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999466 adj=63999567 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.4 raspberry_pi: temp=32.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418065 bytes_read=24347528 bytes_retransmit=9 bytes_invalid=0 send_seq=69673 receive_seq=69673 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999936 coil_temp=26.0 refs=0 mcu_temp=24.11 supply_voltage=3.013 sysload=0.18 cputime=3374.259 memavail=1412468 print_time=70541.831 buffer_time=13.000 print_stall=0 extruder: target=220 temp=221.7 pwm=0.002
Stats 70524.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421501 bytes_read=7904081 bytes_retransmit=9 bytes_invalid=0 send_seq=69929 receive_seq=69929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999667 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418542 bytes_read=1290696 bytes_retransmit=0 bytes_invalid=0 send_seq=69724 receive_seq=69724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998350 adj=49998425 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428151 bytes_read=7677125 bytes_retransmit=9 bytes_invalid=0 send_seq=70104 receive_seq=70104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999469 adj=63999567 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418071 bytes_read=24347884 bytes_retransmit=9 bytes_invalid=0 send_seq=69674 receive_seq=69674 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999937 coil_temp=26.0 refs=0 mcu_temp=24.12 supply_voltage=3.013 sysload=0.17 cputime=3374.317 memavail=1411712 print_time=70541.831 buffer_time=12.000 print_stall=0 extruder: target=220 temp=219.9 pwm=0.459
Stats 70525.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421507 bytes_read=7904184 bytes_retransmit=9 bytes_invalid=0 send_seq=69930 receive_seq=69930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999664 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418548 bytes_read=1290712 bytes_retransmit=0 bytes_invalid=0 send_seq=69725 receive_seq=69725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998352 adj=49998429 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428217 bytes_read=7677276 bytes_retransmit=9 bytes_invalid=0 send_seq=70109 receive_seq=70109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999469 adj=63999569 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418077 bytes_read=24348240 bytes_retransmit=9 bytes_invalid=0 send_seq=69675 receive_seq=69675 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999937 coil_temp=26.0 refs=0 mcu_temp=24.14 supply_voltage=3.013 sysload=0.17 cputime=3374.374 memavail=1411712 print_time=70541.831 buffer_time=10.999 print_stall=0 extruder: target=220 temp=218.5 pwm=0.759
Stats 70526.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421513 bytes_read=7904316 bytes_retransmit=9 bytes_invalid=0 send_seq=69931 receive_seq=69931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418554 bytes_read=1290728 bytes_retransmit=0 bytes_invalid=0 send_seq=69726 receive_seq=69726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998435 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428296 bytes_read=7677446 bytes_retransmit=9 bytes_invalid=0 send_seq=70115 receive_seq=70115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999469 adj=63999572 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418083 bytes_read=24348596 bytes_retransmit=9 bytes_invalid=0 send_seq=69676 receive_seq=69676 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31999937 coil_temp=26.0 refs=0 mcu_temp=24.14 supply_voltage=3.013 sysload=0.17 cputime=3374.435 memavail=1411712 print_time=70541.831 buffer_time=9.998 print_stall=0 extruder: target=220 temp=221.3 pwm=0.000
Stats 70527.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421525 bytes_read=7904430 bytes_retransmit=9 bytes_invalid=0 send_seq=69933 receive_seq=69933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999680 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418560 bytes_read=1290744 bytes_retransmit=0 bytes_invalid=0 send_seq=69727 receive_seq=69727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998438 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428346 bytes_read=7677631 bytes_retransmit=9 bytes_invalid=0 send_seq=70119 receive_seq=70119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999572 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418089 bytes_read=24348952 bytes_retransmit=9 bytes_invalid=0 send_seq=69677 receive_seq=69677 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31999940 coil_temp=26.0 refs=0 mcu_temp=24.15 supply_voltage=3.013 sysload=0.17 cputime=3374.494 memavail=1411712 print_time=70541.831 buffer_time=8.998 print_stall=0 extruder: target=220 temp=221.1 pwm=0.228
Stats 70528.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421531 bytes_read=7904540 bytes_retransmit=9 bytes_invalid=0 send_seq=69934 receive_seq=69934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999678 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418566 bytes_read=1290760 bytes_retransmit=0 bytes_invalid=0 send_seq=69728 receive_seq=69728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998429 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428428 bytes_read=7677793 bytes_retransmit=9 bytes_invalid=0 send_seq=70125 receive_seq=70125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999468 adj=63999562 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418095 bytes_read=24349308 bytes_retransmit=9 bytes_invalid=0 send_seq=69678 receive_seq=69678 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31999937 coil_temp=26.0 refs=0 mcu_temp=24.17 supply_voltage=3.013 sysload=0.17 cputime=3374.552 memavail=1405668 print_time=70541.831 buffer_time=7.997 print_stall=0 extruder: target=220 temp=218.9 pwm=0.698
Stats 70529.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421537 bytes_read=7904672 bytes_retransmit=9 bytes_invalid=0 send_seq=69935 receive_seq=69935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=418572 bytes_read=1290789 bytes_retransmit=0 bytes_invalid=0 send_seq=69729 receive_seq=69729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998349 adj=49998430 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428494 bytes_read=7677966 bytes_retransmit=9 bytes_invalid=0 send_seq=70130 receive_seq=70130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999468 adj=63999560 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=32.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418101 bytes_read=24349664 bytes_retransmit=9 bytes_invalid=0 send_seq=69679 receive_seq=69679 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31999937 coil_temp=26.0 refs=0 mcu_temp=24.17 supply_voltage=3.013 sysload=0.24 cputime=3374.581 memavail=1411224 print_time=70541.831 buffer_time=6.996 print_stall=0 extruder: target=220 temp=219.8 pwm=0.385
Stats 70530.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421543 bytes_read=7904775 bytes_retransmit=9 bytes_invalid=0 send_seq=69936 receive_seq=69936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999669 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=418578 bytes_read=1290805 bytes_retransmit=0 bytes_invalid=0 send_seq=69730 receive_seq=69730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998424 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428556 bytes_read=7678140 bytes_retransmit=9 bytes_invalid=0 send_seq=70135 receive_seq=70135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999466 adj=63999562 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418107 bytes_read=24350020 bytes_retransmit=9 bytes_invalid=0 send_seq=69680 receive_seq=69680 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31999936 coil_temp=26.0 refs=0 mcu_temp=24.17 supply_voltage=3.013 sysload=0.24 cputime=3374.606 memavail=1411224 print_time=70541.831 buffer_time=5.995 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Stats 70531.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421549 bytes_read=7904878 bytes_retransmit=9 bytes_invalid=0 send_seq=69937 receive_seq=69937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999664 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=418584 bytes_read=1290821 bytes_retransmit=0 bytes_invalid=0 send_seq=69731 receive_seq=69731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998418 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428637 bytes_read=7678304 bytes_retransmit=9 bytes_invalid=0 send_seq=70141 receive_seq=70141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999562 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418113 bytes_read=24350376 bytes_retransmit=9 bytes_invalid=0 send_seq=69681 receive_seq=69681 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999936 coil_temp=26.0 refs=0 mcu_temp=24.17 supply_voltage=3.013 sysload=0.24 cputime=3374.632 memavail=1411224 print_time=70541.831 buffer_time=4.995 print_stall=0 extruder: target=220 temp=219.7 pwm=0.556
Stats 70532.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421555 bytes_read=7905010 bytes_retransmit=9 bytes_invalid=0 send_seq=69938 receive_seq=69938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=418590 bytes_read=1290837 bytes_retransmit=0 bytes_invalid=0 send_seq=69732 receive_seq=69732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998412 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428703 bytes_read=7678491 bytes_retransmit=9 bytes_invalid=0 send_seq=70146 receive_seq=70146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999562 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418119 bytes_read=24350732 bytes_retransmit=9 bytes_invalid=0 send_seq=69682 receive_seq=69682 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999935 coil_temp=26.1 refs=0 mcu_temp=24.18 supply_voltage=3.013 sysload=0.24 cputime=3374.658 memavail=1411004 print_time=70541.831 buffer_time=3.994 print_stall=0 extruder: target=220 temp=219.6 pwm=0.470
Stats 70533.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421561 bytes_read=7905127 bytes_retransmit=9 bytes_invalid=0 send_seq=69939 receive_seq=69939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999672 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=418596 bytes_read=1290852 bytes_retransmit=0 bytes_invalid=0 send_seq=69733 receive_seq=69733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998406 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428768 bytes_read=7678665 bytes_retransmit=9 bytes_invalid=0 send_seq=70151 receive_seq=70151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999561 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418125 bytes_read=24351088 bytes_retransmit=9 bytes_invalid=0 send_seq=69683 receive_seq=69683 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999937 coil_temp=26.1 refs=0 mcu_temp=24.19 supply_voltage=3.013 sysload=0.24 cputime=3374.691 memavail=1411004 print_time=70541.831 buffer_time=2.994 print_stall=0 extruder: target=220 temp=222.3 pwm=0.031
Stats 70534.4: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=421861 bytes_read=7905255 bytes_retransmit=9 bytes_invalid=0 send_seq=69945 receive_seq=69945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=179999675 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=418602 bytes_read=1290880 bytes_retransmit=0 bytes_invalid=0 send_seq=69734 receive_seq=69734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998395 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428828 bytes_read=7678819 bytes_retransmit=9 bytes_invalid=0 send_seq=70155 receive_seq=70155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999554 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.6 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418131 bytes_read=24351444 bytes_retransmit=9 bytes_invalid=0 send_seq=69684 receive_seq=69684 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31999932 coil_temp=26.1 refs=0 mcu_temp=24.19 supply_voltage=3.013 sysload=0.22 cputime=3374.777 memavail=1411008 print_time=70542.896 buffer_time=3.034 print_stall=0 extruder: target=220 temp=220.3 pwm=0.388
Stats 70535.4: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=422981 bytes_read=7906671 bytes_retransmit=9 bytes_invalid=0 send_seq=70012 receive_seq=70012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999683 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=418608 bytes_read=1290895 bytes_retransmit=0 bytes_invalid=0 send_seq=69735 receive_seq=69735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998393 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428878 bytes_read=7678987 bytes_retransmit=9 bytes_invalid=0 send_seq=70159 receive_seq=70159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999553 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418137 bytes_read=24351800 bytes_retransmit=9 bytes_invalid=0 send_seq=69685 receive_seq=69685 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999933 coil_temp=26.1 refs=0 mcu_temp=24.20 supply_voltage=3.013 sysload=0.22 cputime=3374.922 memavail=1411008 print_time=70542.896 buffer_time=2.033 print_stall=0 extruder: target=220 temp=219.3 pwm=0.565
Stats 70536.4: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=423071 bytes_read=7906918 bytes_retransmit=9 bytes_invalid=0 send_seq=70019 receive_seq=70019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999682 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=418620 bytes_read=1290925 bytes_retransmit=0 bytes_invalid=0 send_seq=69737 receive_seq=69737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998388 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=428972 bytes_read=7679185 bytes_retransmit=9 bytes_invalid=0 send_seq=70166 receive_seq=70166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999549 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418143 bytes_read=24352156 bytes_retransmit=9 bytes_invalid=0 send_seq=69686 receive_seq=69686 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999928 coil_temp=26.1 refs=0 mcu_temp=24.21 supply_voltage=3.013 sysload=0.22 cputime=3374.999 memavail=1411008 print_time=70542.896 buffer_time=1.033 print_stall=0 extruder: target=220 temp=221.6 pwm=0.000
Stats 70537.4: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=423379 bytes_read=7907185 bytes_retransmit=9 bytes_invalid=0 send_seq=70030 receive_seq=70030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999679 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=418626 bytes_read=1290940 bytes_retransmit=0 bytes_invalid=0 send_seq=69738 receive_seq=69738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998396 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429037 bytes_read=7679344 bytes_retransmit=9 bytes_invalid=0 send_seq=70171 receive_seq=70171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999550 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418149 bytes_read=24352512 bytes_retransmit=9 bytes_invalid=0 send_seq=69687 receive_seq=69687 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999928 coil_temp=26.1 refs=0 mcu_temp=24.20 supply_voltage=3.013 sysload=0.22 cputime=3375.074 memavail=1410764 print_time=70542.896 buffer_time=0.032 print_stall=0 extruder: target=220 temp=220.3 pwm=0.335
Stats 70538.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=425753 bytes_read=7909464 bytes_retransmit=9 bytes_invalid=0 send_seq=70155 receive_seq=70155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999676 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=418632 bytes_read=1290956 bytes_retransmit=0 bytes_invalid=0 send_seq=69739 receive_seq=69739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998403 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429119 bytes_read=7679522 bytes_retransmit=9 bytes_invalid=0 send_seq=70177 receive_seq=70177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999554 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418155 bytes_read=24352868 bytes_retransmit=9 bytes_invalid=0 send_seq=69688 receive_seq=69688 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999929 coil_temp=26.1 refs=0 mcu_temp=24.21 supply_voltage=3.013 sysload=0.22 cputime=3375.294 memavail=1410764 print_time=70544.062 buffer_time=0.000 print_stall=0 extruder: target=220 temp=218.9 pwm=0.630
Stats 70539.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=426766 bytes_read=7910245 bytes_retransmit=9 bytes_invalid=0 send_seq=70202 receive_seq=70202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000023 bytes_write=418638 bytes_read=1290985 bytes_retransmit=0 bytes_invalid=0 send_seq=69740 receive_seq=69740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998408 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429209 bytes_read=7679701 bytes_retransmit=9 bytes_invalid=0 send_seq=70183 receive_seq=70183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999556 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418161 bytes_read=24353224 bytes_retransmit=9 bytes_invalid=0 send_seq=69689 receive_seq=69689 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999929 coil_temp=26.1 refs=0 mcu_temp=24.21 supply_voltage=3.013 sysload=0.28 cputime=3375.418 memavail=1410764 print_time=70545.062 buffer_time=0.000 print_stall=0 extruder: target=220 temp=221.3 pwm=0.001
Stats 70540.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=427779 bytes_read=7911040 bytes_retransmit=9 bytes_invalid=0 send_seq=70249 receive_seq=70249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=179999673 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000023 bytes_write=418644 bytes_read=1291001 bytes_retransmit=0 bytes_invalid=0 send_seq=69741 receive_seq=69741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998408 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429258 bytes_read=7679855 bytes_retransmit=9 bytes_invalid=0 send_seq=70187 receive_seq=70187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999557 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.8 raspberry_pi: temp=32.1 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418167 bytes_read=24353580 bytes_retransmit=9 bytes_invalid=0 send_seq=69690 receive_seq=69690 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999930 coil_temp=26.1 refs=0 mcu_temp=24.21 supply_voltage=3.013 sysload=0.28 cputime=3375.537 memavail=1410768 print_time=70546.062 buffer_time=0.000 print_stall=0 extruder: target=220 temp=221.2 pwm=0.123
Stats 70541.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=428804 bytes_read=7911855 bytes_retransmit=9 bytes_invalid=0 send_seq=70297 receive_seq=70297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000023 bytes_write=418650 bytes_read=1291017 bytes_retransmit=0 bytes_invalid=0 send_seq=69742 receive_seq=69742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998410 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429335 bytes_read=7680042 bytes_retransmit=9 bytes_invalid=0 send_seq=70192 receive_seq=70192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999557 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418173 bytes_read=24353936 bytes_retransmit=9 bytes_invalid=0 send_seq=69691 receive_seq=69691 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999930 coil_temp=26.1 refs=0 mcu_temp=24.22 supply_voltage=3.013 sysload=0.28 cputime=3375.658 memavail=1410768 print_time=70547.062 buffer_time=0.000 print_stall=0 extruder: target=220 temp=218.6 pwm=0.738
Stats 70542.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=429822 bytes_read=7912641 bytes_retransmit=9 bytes_invalid=0 send_seq=70345 receive_seq=70345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999669 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000023 bytes_write=418656 bytes_read=1291033 bytes_retransmit=0 bytes_invalid=0 send_seq=69743 receive_seq=69743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998408 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429427 bytes_read=7680221 bytes_retransmit=9 bytes_invalid=0 send_seq=70198 receive_seq=70198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999556 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418185 bytes_read=24354308 bytes_retransmit=9 bytes_invalid=0 send_seq=69693 receive_seq=69693 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999928 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.28 cputime=3375.783 memavail=1410768 print_time=70548.062 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.9 pwm=0.091
Stats 70543.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=431163 bytes_read=7913606 bytes_retransmit=9 bytes_invalid=0 send_seq=70404 receive_seq=70404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999664 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000023 bytes_write=418662 bytes_read=1291049 bytes_retransmit=0 bytes_invalid=0 send_seq=69744 receive_seq=69744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998410 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429474 bytes_read=7680375 bytes_retransmit=9 bytes_invalid=0 send_seq=70202 receive_seq=70202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999559 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=33.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418191 bytes_read=24354664 bytes_retransmit=9 bytes_invalid=0 send_seq=69694 receive_seq=69694 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999932 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.28 cputime=3375.918 memavail=1410768 print_time=70549.045 buffer_time=0.000 print_stall=0 extruder: target=220 temp=221.8 pwm=0.000
Stats 70544.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=436959 bytes_read=7914815 bytes_retransmit=9 bytes_invalid=0 send_seq=70526 receive_seq=70526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=418668 bytes_read=1291078 bytes_retransmit=0 bytes_invalid=0 send_seq=69745 receive_seq=69745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998416 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=429588 bytes_read=7680553 bytes_retransmit=9 bytes_invalid=0 send_seq=70208 receive_seq=70208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999562 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=22.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418197 bytes_read=24355020 bytes_retransmit=9 bytes_invalid=0 send_seq=69695 receive_seq=69695 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999933 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.34 cputime=3376.086 memavail=1410524 print_time=70550.197 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.5 pwm=0.568
Stats 70545.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=438660 bytes_read=7917111 bytes_retransmit=9 bytes_invalid=0 send_seq=70652 receive_seq=70652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999651 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=418674 bytes_read=1291094 bytes_retransmit=0 bytes_invalid=0 send_seq=69746 receive_seq=69746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998414 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=430783 bytes_read=7682489 bytes_retransmit=9 bytes_invalid=0 send_seq=70305 receive_seq=70305 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999460 adj=63999563 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418203 bytes_read=24355376 bytes_retransmit=9 bytes_invalid=0 send_seq=69696 receive_seq=69696 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999933 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.34 cputime=3376.172 memavail=1410524 print_time=70551.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.3 pwm=0.247
Stats 70546.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=440850 bytes_read=7920182 bytes_retransmit=9 bytes_invalid=0 send_seq=70821 receive_seq=70821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999645 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=418680 bytes_read=1291110 bytes_retransmit=0 bytes_invalid=0 send_seq=69747 receive_seq=69747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998411 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=432435 bytes_read=7685186 bytes_retransmit=9 bytes_invalid=0 send_seq=70442 receive_seq=70442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999562 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.0 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418209 bytes_read=24355732 bytes_retransmit=9 bytes_invalid=0 send_seq=69697 receive_seq=69697 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31999937 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.34 cputime=3376.283 memavail=1412288 print_time=70552.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=222.1 pwm=0.017
Stats 70547.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=443052 bytes_read=7923287 bytes_retransmit=9 bytes_invalid=0 send_seq=70991 receive_seq=70991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999641 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=418686 bytes_read=1291126 bytes_retransmit=0 bytes_invalid=0 send_seq=69748 receive_seq=69748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998329 adj=49998407 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=434099 bytes_read=7687910 bytes_retransmit=9 bytes_invalid=0 send_seq=70579 receive_seq=70579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=11 freq=63999467 adj=63999571 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418215 bytes_read=24356088 bytes_retransmit=9 bytes_invalid=0 send_seq=69698 receive_seq=69698 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31999941 coil_temp=26.1 refs=0 mcu_temp=24.23 supply_voltage=3.013 sysload=0.34 cputime=3376.378 memavail=1412288 print_time=70553.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.5 pwm=0.534
Stats 70548.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000009 mcu_task_stddev=0.000014 bytes_write=445242 bytes_read=7926388 bytes_retransmit=9 bytes_invalid=0 send_seq=71160 receive_seq=71160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999634 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=418692 bytes_read=1291142 bytes_retransmit=0 bytes_invalid=0 send_seq=69749 receive_seq=69749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998326 adj=49998403 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=435786 bytes_read=7690596 bytes_retransmit=9 bytes_invalid=0 send_seq=70717 receive_seq=70717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999582 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418221 bytes_read=24356444 bytes_retransmit=9 bytes_invalid=0 send_seq=69699 receive_seq=69699 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999940 coil_temp=26.1 refs=0 mcu_temp=24.22 supply_voltage=3.013 sysload=0.34 cputime=3376.473 memavail=1412288 print_time=70554.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.5 pwm=0.455
Stats 70549.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000009 mcu_task_stddev=0.000014 bytes_write=447427 bytes_read=7929454 bytes_retransmit=9 bytes_invalid=0 send_seq=71328 receive_seq=71328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999633 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=418698 bytes_read=1291171 bytes_retransmit=0 bytes_invalid=0 send_seq=69750 receive_seq=69750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998327 adj=49998401 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=437449 bytes_read=7693291 bytes_retransmit=9 bytes_invalid=0 send_seq=70854 receive_seq=70854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999582 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418227 bytes_read=24356800 bytes_retransmit=9 bytes_invalid=0 send_seq=69700 receive_seq=69700 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999940 coil_temp=26.1 refs=0 mcu_temp=24.21 supply_voltage=3.013 sysload=0.39 cputime=3376.637 memavail=1412288 print_time=70555.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=222.0 pwm=0.045
Stats 70550.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000009 mcu_task_stddev=0.000014 bytes_write=449617 bytes_read=7932568 bytes_retransmit=9 bytes_invalid=0 send_seq=71497 receive_seq=71497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=418704 bytes_read=1291187 bytes_retransmit=0 bytes_invalid=0 send_seq=69751 receive_seq=69751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998329 adj=49998404 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=439114 bytes_read=7696006 bytes_retransmit=9 bytes_invalid=0 send_seq=70992 receive_seq=70992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999461 adj=63999581 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418233 bytes_read=24357156 bytes_retransmit=9 bytes_invalid=0 send_seq=69701 receive_seq=69701 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999940 coil_temp=26.1 refs=0 mcu_temp=24.20 supply_voltage=3.013 sysload=0.39 cputime=3376.857 memavail=1412292 print_time=70556.047 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.5 pwm=0.247
Stats 70551.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000009 mcu_task_stddev=0.000014 bytes_write=451377 bytes_read=7934691 bytes_retransmit=9 bytes_invalid=0 send_seq=71618 receive_seq=71618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=418710 bytes_read=1291203 bytes_retransmit=0 bytes_invalid=0 send_seq=69752 receive_seq=69752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998397 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=440169 bytes_read=7697749 bytes_retransmit=9 bytes_invalid=0 send_seq=71077 receive_seq=71077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999562 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=0 temp=23.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418239 bytes_read=24357512 bytes_retransmit=9 bytes_invalid=0 send_seq=69702 receive_seq=69702 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31999932 coil_temp=26.1 refs=0 mcu_temp=24.19 supply_voltage=3.013 sysload=0.39 cputime=3377.042 memavail=1412300 print_time=70557.084 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.0 pwm=0.602
Stats 70552.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000009 mcu_task_stddev=0.000014 bytes_write=454680 bytes_read=7935851 bytes_retransmit=9 bytes_invalid=0 send_seq=71708 receive_seq=71708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=418716 bytes_read=1291219 bytes_retransmit=0 bytes_invalid=0 send_seq=69753 receive_seq=69753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998389 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=440539 bytes_read=7698366 bytes_retransmit=9 bytes_invalid=0 send_seq=71108 receive_seq=71108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999462 adj=63999552 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=32.9 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=0 temp=23.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=418245 bytes_read=24357868 bytes_retransmit=9 bytes_invalid=0 send_seq=69703 receive_seq=69703 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999926 coil_temp=26.1 refs=0 mcu_temp=24.19 supply_voltage=3.013 sysload=0.39 cputime=3377.171 memavail=1412300 print_time=70557.883 buffer_time=0.001 print_stall=0 extruder: target=220 temp=221.0 pwm=0.049
RatOS:: Homing Z
Stats 70553.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000008 mcu_task_stddev=0.000006 bytes_write=456720 bytes_read=7938255 bytes_retransmit=9 bytes_invalid=0 send_seq=71841 receive_seq=71841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=418722 bytes_read=1291235 bytes_retransmit=0 bytes_invalid=0 send_seq=69754 receive_seq=69754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998325 adj=49998386 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=440573 bytes_read=7698544 bytes_retransmit=9 bytes_invalid=0 send_seq=71111 receive_seq=71111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999461 adj=63999554 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=419446 bytes_read=24360049 bytes_retransmit=9 bytes_invalid=0 send_seq=69803 receive_seq=69803 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999927 coil_temp=26.1 refs=0 mcu_temp=24.18 supply_voltage=3.013 sysload=0.39 cputime=3377.276 memavail=1412300 print_time=70559.094 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.5 pwm=0.291
Stats 70554.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000008 mcu_task_stddev=0.000006 bytes_write=459050 bytes_read=7941326 bytes_retransmit=9 bytes_invalid=0 send_seq=72010 receive_seq=72010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999695 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000016 bytes_write=418728 bytes_read=1291264 bytes_retransmit=0 bytes_invalid=0 send_seq=69755 receive_seq=69755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998322 adj=49998383 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=440666 bytes_read=7698708 bytes_retransmit=9 bytes_invalid=0 send_seq=71117 receive_seq=71117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999459 adj=63999555 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=0 temp=23.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=421060 bytes_read=24362937 bytes_retransmit=9 bytes_invalid=0 send_seq=69938 receive_seq=69938 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999926 coil_temp=26.1 refs=0 mcu_temp=24.18 supply_voltage=3.013 sysload=0.44 cputime=3377.378 memavail=1412780 print_time=70560.094 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.1 pwm=0.573
Stats 70555.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000008 mcu_task_stddev=0.000006 bytes_write=461392 bytes_read=7944416 bytes_retransmit=9 bytes_invalid=0 send_seq=72180 receive_seq=72180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999688 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000016 bytes_write=418734 bytes_read=1291280 bytes_retransmit=0 bytes_invalid=0 send_seq=69756 receive_seq=69756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998358 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=440743 bytes_read=7698867 bytes_retransmit=9 bytes_invalid=0 send_seq=71122 receive_seq=71122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999458 adj=63999527 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=422686 bytes_read=24365844 bytes_retransmit=9 bytes_invalid=0 send_seq=70074 receive_seq=70074 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999911 coil_temp=26.2 refs=0 mcu_temp=24.18 supply_voltage=3.013 sysload=0.44 cputime=3377.479 memavail=1412836 print_time=70561.094 buffer_time=0.000 print_stall=0 extruder: target=220 temp=220.1 pwm=0.272
Stats 70556.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000008 mcu_task_stddev=0.000006 bytes_write=462584 bytes_read=7945664 bytes_retransmit=9 bytes_invalid=0 send_seq=72245 receive_seq=72245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999693 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000016 bytes_write=418740 bytes_read=1291296 bytes_retransmit=0 bytes_invalid=0 send_seq=69757 receive_seq=69757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998317 adj=49998355 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440805 bytes_read=7699070 bytes_retransmit=9 bytes_invalid=0 send_seq=71127 receive_seq=71127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999460 adj=63999529 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=0 temp=23.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423074 bytes_read=24368730 bytes_retransmit=9 bytes_invalid=0 send_seq=70109 receive_seq=70109 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999913 coil_temp=26.3 refs=1 mcu_temp=24.19 supply_voltage=3.013 sysload=0.44 cputime=3377.645 memavail=1412836 print_time=70562.102 buffer_time=0.215 print_stall=0 extruder: target=220 temp=221.3 pwm=0.064
RatOS:: Pre-heating extruder...
RatOS:: Heat soaking z probe...
RatOS:: Heating bed...
Stats 70557.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000008 mcu_task_stddev=0.000006 bytes_write=463658 bytes_read=7946178 bytes_retransmit=9 bytes_invalid=0 send_seq=72275 receive_seq=72275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999686 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000016 bytes_write=418746 bytes_read=1291312 bytes_retransmit=0 bytes_invalid=0 send_seq=69758 receive_seq=69758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998315 adj=49998348 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440862 bytes_read=7699224 bytes_retransmit=9 bytes_invalid=0 send_seq=71131 receive_seq=71131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999530 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.0 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=23.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423087 bytes_read=24369742 bytes_retransmit=9 bytes_invalid=0 send_seq=70111 receive_seq=70111 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999911 coil_temp=26.5 refs=0 mcu_temp=24.22 supply_voltage=3.013 sysload=0.44 cputime=3377.827 memavail=1412840 print_time=70564.214 buffer_time=1.326 print_stall=0 extruder: target=150 temp=219.0 pwm=0.000
Heater heater_bed approaching new target of 55.000
Stats 70558.4: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=463860 bytes_read=7946633 bytes_retransmit=9 bytes_invalid=0 send_seq=72290 receive_seq=72290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999679 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000016 bytes_write=418752 bytes_read=1291328 bytes_retransmit=0 bytes_invalid=0 send_seq=69759 receive_seq=69759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998313 adj=49998348 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440896 bytes_read=7699373 bytes_retransmit=9 bytes_invalid=0 send_seq=71134 receive_seq=71134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999462 adj=63999544 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=23.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423093 bytes_read=24370098 bytes_retransmit=9 bytes_invalid=0 send_seq=70112 receive_seq=70112 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999914 coil_temp=26.6 refs=0 mcu_temp=24.25 supply_voltage=3.013 sysload=0.44 cputime=3377.867 memavail=1412840 print_time=70564.214 buffer_time=0.326 print_stall=0 extruder: target=150 temp=216.3 pwm=0.000
Stats 70559.4: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=464295 bytes_read=7947121 bytes_retransmit=9 bytes_invalid=0 send_seq=72309 receive_seq=72309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999673 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=418758 bytes_read=1291357 bytes_retransmit=0 bytes_invalid=0 send_seq=69760 receive_seq=69760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998312 adj=49998349 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440930 bytes_read=7699551 bytes_retransmit=9 bytes_invalid=0 send_seq=71137 receive_seq=71137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999460 adj=63999545 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=23.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423099 bytes_read=24370454 bytes_retransmit=9 bytes_invalid=0 send_seq=70113 receive_seq=70113 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999915 coil_temp=26.6 refs=0 mcu_temp=24.27 supply_voltage=3.013 sysload=0.40 cputime=3377.910 memavail=1412840 print_time=70564.504 buffer_time=0.000 print_stall=0 extruder: target=150 temp=213.2 pwm=0.000
Stats 70560.4: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=464497 bytes_read=7947560 bytes_retransmit=9 bytes_invalid=0 send_seq=72324 receive_seq=72324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=418764 bytes_read=1291373 bytes_retransmit=0 bytes_invalid=0 send_seq=69761 receive_seq=69761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998311 adj=49998349 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440964 bytes_read=7699700 bytes_retransmit=9 bytes_invalid=0 send_seq=71140 receive_seq=71140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999459 adj=63999546 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=23.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423105 bytes_read=24370810 bytes_retransmit=9 bytes_invalid=0 send_seq=70114 receive_seq=70114 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999916 coil_temp=26.8 refs=0 mcu_temp=24.31 supply_voltage=3.013 sysload=0.40 cputime=3377.951 memavail=1412840 print_time=70565.431 buffer_time=0.000 print_stall=0 extruder: target=150 temp=211.4 pwm=0.000
Stats 70561.4: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=464715 bytes_read=7948004 bytes_retransmit=9 bytes_invalid=0 send_seq=72340 receive_seq=72340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=418770 bytes_read=1291389 bytes_retransmit=0 bytes_invalid=0 send_seq=69762 receive_seq=69762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998308 adj=49998350 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=440998 bytes_read=7699849 bytes_retransmit=9 bytes_invalid=0 send_seq=71143 receive_seq=71143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999458 adj=63999548 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=23.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423111 bytes_read=24371166 bytes_retransmit=9 bytes_invalid=0 send_seq=70115 receive_seq=70115 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999918 coil_temp=26.9 refs=0 mcu_temp=24.36 supply_voltage=3.013 sysload=0.40 cputime=3377.992 memavail=1412844 print_time=70566.431 buffer_time=0.000 print_stall=0 extruder: target=150 temp=209.2 pwm=0.000
Stats 70562.4: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=464917 bytes_read=7948472 bytes_retransmit=9 bytes_invalid=0 send_seq=72355 receive_seq=72355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999666 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=418776 bytes_read=1291405 bytes_retransmit=0 bytes_invalid=0 send_seq=69763 receive_seq=69763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998311 adj=49998348 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=441032 bytes_read=7700041 bytes_retransmit=9 bytes_invalid=0 send_seq=71146 receive_seq=71146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999457 adj=63999548 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.3 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=23.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423117 bytes_read=24371522 bytes_retransmit=9 bytes_invalid=0 send_seq=70116 receive_seq=70116 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999919 coil_temp=27.0 refs=0 mcu_temp=24.41 supply_voltage=3.013 sysload=0.40 cputime=3378.076 memavail=1412848 print_time=70567.431 buffer_time=0.000 print_stall=0 extruder: target=150 temp=207.0 pwm=0.000
Stats 70563.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=465119 bytes_read=7948926 bytes_retransmit=9 bytes_invalid=0 send_seq=72370 receive_seq=72370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999664 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=418782 bytes_read=1291421 bytes_retransmit=0 bytes_invalid=0 send_seq=69764 receive_seq=69764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998310 adj=49998353 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=441066 bytes_read=7700190 bytes_retransmit=9 bytes_invalid=0 send_seq=71149 receive_seq=71149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999455 adj=63999546 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=23.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423123 bytes_read=24371878 bytes_retransmit=9 bytes_invalid=0 send_seq=70117 receive_seq=70117 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999919 coil_temp=27.2 refs=0 mcu_temp=24.46 supply_voltage=3.013 sysload=0.40 cputime=3378.135 memavail=1413260 print_time=70568.432 buffer_time=0.000 print_stall=0 extruder: target=150 temp=205.4 pwm=0.000
Stats 70564.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=465321 bytes_read=7949365 bytes_retransmit=9 bytes_invalid=0 send_seq=72385 receive_seq=72385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418788 bytes_read=1291450 bytes_retransmit=0 bytes_invalid=0 send_seq=69765 receive_seq=69765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998308 adj=49998350 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=441100 bytes_read=7700339 bytes_retransmit=9 bytes_invalid=0 send_seq=71152 receive_seq=71152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999543 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=23.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423129 bytes_read=24372234 bytes_retransmit=9 bytes_invalid=0 send_seq=70118 receive_seq=70118 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999918 coil_temp=27.3 refs=0 mcu_temp=24.54 supply_voltage=3.013 sysload=0.37 cputime=3378.176 memavail=1412160 print_time=70569.433 buffer_time=0.000 print_stall=0 extruder: target=150 temp=203.1 pwm=0.000
Stats 70565.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=465539 bytes_read=7949838 bytes_retransmit=9 bytes_invalid=0 send_seq=72401 receive_seq=72401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999654 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418794 bytes_read=1291466 bytes_retransmit=0 bytes_invalid=0 send_seq=69766 receive_seq=69766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998306 adj=49998349 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=441134 bytes_read=7700517 bytes_retransmit=9 bytes_invalid=0 send_seq=71155 receive_seq=71155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999452 adj=63999542 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=24.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423135 bytes_read=24372590 bytes_retransmit=9 bytes_invalid=0 send_seq=70119 receive_seq=70119 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999865 adj=31999919 coil_temp=27.4 refs=0 mcu_temp=24.58 supply_voltage=3.013 sysload=0.37 cputime=3378.215 memavail=1412164 print_time=70570.433 buffer_time=0.000 print_stall=0 extruder: target=150 temp=201.2 pwm=0.000
Stats 70566.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=465741 bytes_read=7950277 bytes_retransmit=9 bytes_invalid=0 send_seq=72416 receive_seq=72416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999650 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418800 bytes_read=1291482 bytes_retransmit=0 bytes_invalid=0 send_seq=69767 receive_seq=69767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998304 adj=49998349 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=441168 bytes_read=7700666 bytes_retransmit=9 bytes_invalid=0 send_seq=71158 receive_seq=71158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999451 adj=63999544 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=24.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423141 bytes_read=24372946 bytes_retransmit=9 bytes_invalid=0 send_seq=70120 receive_seq=70120 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999921 coil_temp=27.5 refs=0 mcu_temp=24.64 supply_voltage=3.013 sysload=0.37 cputime=3378.254 memavail=1412164 print_time=70571.433 buffer_time=0.000 print_stall=0 extruder: target=150 temp=199.2 pwm=0.000
Stats 70567.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=465943 bytes_read=7950716 bytes_retransmit=9 bytes_invalid=0 send_seq=72431 receive_seq=72431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999649 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418806 bytes_read=1291498 bytes_retransmit=0 bytes_invalid=0 send_seq=69768 receive_seq=69768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998303 adj=49998347 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441202 bytes_read=7700829 bytes_retransmit=9 bytes_invalid=0 send_seq=71161 receive_seq=71161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999545 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.3 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=24.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423147 bytes_read=24373302 bytes_retransmit=9 bytes_invalid=0 send_seq=70121 receive_seq=70121 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999923 coil_temp=27.7 refs=0 mcu_temp=24.69 supply_voltage=3.013 sysload=0.37 cputime=3378.294 memavail=1412164 print_time=70572.433 buffer_time=0.000 print_stall=0 extruder: target=150 temp=197.9 pwm=0.000
Stats 70568.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=466145 bytes_read=7951199 bytes_retransmit=9 bytes_invalid=0 send_seq=72446 receive_seq=72446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999654 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418812 bytes_read=1291514 bytes_retransmit=0 bytes_invalid=0 send_seq=69769 receive_seq=69769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998307 adj=49998344 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441236 bytes_read=7701007 bytes_retransmit=9 bytes_invalid=0 send_seq=71164 receive_seq=71164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999542 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=33.3 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=24.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423153 bytes_read=24373658 bytes_retransmit=9 bytes_invalid=0 send_seq=70122 receive_seq=70122 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999925 coil_temp=27.8 refs=0 mcu_temp=24.74 supply_voltage=3.013 sysload=0.37 cputime=3378.377 memavail=1412164 print_time=70573.434 buffer_time=0.000 print_stall=0 extruder: target=150 temp=195.7 pwm=0.000
Stats 70569.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=466347 bytes_read=7951638 bytes_retransmit=9 bytes_invalid=0 send_seq=72461 receive_seq=72461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999666 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=418818 bytes_read=1291543 bytes_retransmit=0 bytes_invalid=0 send_seq=69770 receive_seq=69770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998309 adj=49998350 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441270 bytes_read=7701156 bytes_retransmit=9 bytes_invalid=0 send_seq=71167 receive_seq=71167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999451 adj=63999540 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=25.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423159 bytes_read=24374014 bytes_retransmit=9 bytes_invalid=0 send_seq=70123 receive_seq=70123 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999925 coil_temp=28.0 refs=0 mcu_temp=24.80 supply_voltage=3.013 sysload=0.34 cputime=3378.474 memavail=1412164 print_time=70574.435 buffer_time=0.000 print_stall=0 extruder: target=150 temp=193.9 pwm=0.000
Stats 70570.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=466565 bytes_read=7952082 bytes_retransmit=9 bytes_invalid=0 send_seq=72477 receive_seq=72477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999666 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=418824 bytes_read=1291559 bytes_retransmit=0 bytes_invalid=0 send_seq=69771 receive_seq=69771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998310 adj=49998348 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441304 bytes_read=7701305 bytes_retransmit=9 bytes_invalid=0 send_seq=71170 receive_seq=71170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999529 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.3 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=25.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423165 bytes_read=24374370 bytes_retransmit=9 bytes_invalid=0 send_seq=70124 receive_seq=70124 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999921 coil_temp=28.0 refs=0 mcu_temp=24.85 supply_voltage=3.013 sysload=0.34 cputime=3378.569 memavail=1412164 print_time=70575.436 buffer_time=0.000 print_stall=0 extruder: target=150 temp=192.4 pwm=0.000
Stats 70571.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=466767 bytes_read=7952550 bytes_retransmit=9 bytes_invalid=0 send_seq=72492 receive_seq=72492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999667 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=418830 bytes_read=1291575 bytes_retransmit=0 bytes_invalid=0 send_seq=69772 receive_seq=69772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998313 adj=49998351 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441338 bytes_read=7701483 bytes_retransmit=9 bytes_invalid=0 send_seq=71173 receive_seq=71173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999528 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=33.3 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=25.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423171 bytes_read=24374726 bytes_retransmit=9 bytes_invalid=0 send_seq=70125 receive_seq=70125 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999922 coil_temp=28.1 refs=0 mcu_temp=24.93 supply_voltage=3.013 sysload=0.34 cputime=3378.668 memavail=1412164 print_time=70576.436 buffer_time=0.000 print_stall=0 extruder: target=150 temp=190.2 pwm=0.000
Stats 70572.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=466969 bytes_read=7952989 bytes_retransmit=9 bytes_invalid=0 send_seq=72507 receive_seq=72507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999667 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=418836 bytes_read=1291591 bytes_retransmit=0 bytes_invalid=0 send_seq=69773 receive_seq=69773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998315 adj=49998357 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441372 bytes_read=7701646 bytes_retransmit=9 bytes_invalid=0 send_seq=71176 receive_seq=71176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999449 adj=63999526 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=26.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423177 bytes_read=24375082 bytes_retransmit=9 bytes_invalid=0 send_seq=70126 receive_seq=70126 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999921 coil_temp=28.2 refs=0 mcu_temp=24.99 supply_voltage=3.013 sysload=0.34 cputime=3378.765 memavail=1412164 print_time=70577.437 buffer_time=0.000 print_stall=0 extruder: target=150 temp=188.8 pwm=0.000
Stats 70573.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=467171 bytes_read=7953443 bytes_retransmit=9 bytes_invalid=0 send_seq=72522 receive_seq=72522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=418842 bytes_read=1291607 bytes_retransmit=0 bytes_invalid=0 send_seq=69774 receive_seq=69774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998316 adj=49998362 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441406 bytes_read=7701795 bytes_retransmit=9 bytes_invalid=0 send_seq=71179 receive_seq=71179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999525 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=26.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423183 bytes_read=24375438 bytes_retransmit=9 bytes_invalid=0 send_seq=70127 receive_seq=70127 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999923 coil_temp=28.3 refs=0 mcu_temp=25.05 supply_voltage=3.013 sysload=0.34 cputime=3378.862 memavail=1412164 print_time=70578.437 buffer_time=0.000 print_stall=0 extruder: target=150 temp=187.1 pwm=0.000
Stats 70574.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=467384 bytes_read=7953911 bytes_retransmit=9 bytes_invalid=0 send_seq=72537 receive_seq=72537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999671 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=418848 bytes_read=1291636 bytes_retransmit=0 bytes_invalid=0 send_seq=69775 receive_seq=69775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998320 adj=49998365 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441440 bytes_read=7701973 bytes_retransmit=9 bytes_invalid=0 send_seq=71182 receive_seq=71182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999454 adj=63999535 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=26.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423189 bytes_read=24375794 bytes_retransmit=9 bytes_invalid=0 send_seq=70128 receive_seq=70128 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999925 coil_temp=28.4 refs=0 mcu_temp=25.11 supply_voltage=3.013 sysload=0.31 cputime=3378.960 memavail=1412164 print_time=70579.437 buffer_time=0.000 print_stall=0 extruder: target=150 temp=185.5 pwm=0.000
Stats 70575.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=467586 bytes_read=7954344 bytes_retransmit=9 bytes_invalid=0 send_seq=72552 receive_seq=72552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999673 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=418854 bytes_read=1291652 bytes_retransmit=0 bytes_invalid=0 send_seq=69776 receive_seq=69776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998324 adj=49998373 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441474 bytes_read=7702122 bytes_retransmit=9 bytes_invalid=0 send_seq=71185 receive_seq=71185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999533 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=32.1 sd_pos=41100 heater_bed: target=55 temp=26.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423195 bytes_read=24376150 bytes_retransmit=9 bytes_invalid=0 send_seq=70129 receive_seq=70129 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999924 coil_temp=28.5 refs=0 mcu_temp=25.16 supply_voltage=3.013 sysload=0.31 cputime=3379.057 memavail=1412164 print_time=70580.437 buffer_time=0.000 print_stall=0 extruder: target=150 temp=184.1 pwm=0.000
Stats 70576.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=467788 bytes_read=7954778 bytes_retransmit=9 bytes_invalid=0 send_seq=72567 receive_seq=72567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999674 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=418860 bytes_read=1291668 bytes_retransmit=0 bytes_invalid=0 send_seq=69777 receive_seq=69777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998383 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441508 bytes_read=7702271 bytes_retransmit=9 bytes_invalid=0 send_seq=71188 receive_seq=71188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999529 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=27.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423201 bytes_read=24376506 bytes_retransmit=9 bytes_invalid=0 send_seq=70130 receive_seq=70130 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999923 coil_temp=28.6 refs=0 mcu_temp=25.21 supply_voltage=3.013 sysload=0.31 cputime=3379.152 memavail=1412164 print_time=70581.438 buffer_time=0.000 print_stall=0 extruder: target=150 temp=182.6 pwm=0.000
Stats 70577.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=467990 bytes_read=7955246 bytes_retransmit=9 bytes_invalid=0 send_seq=72582 receive_seq=72582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999677 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=418866 bytes_read=1291684 bytes_retransmit=0 bytes_invalid=0 send_seq=69778 receive_seq=69778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998394 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441542 bytes_read=7702463 bytes_retransmit=9 bytes_invalid=0 send_seq=71191 receive_seq=71191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999455 adj=63999526 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=27.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423207 bytes_read=24376862 bytes_retransmit=9 bytes_invalid=0 send_seq=70131 receive_seq=70131 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999922 coil_temp=28.7 refs=0 mcu_temp=25.26 supply_voltage=3.013 sysload=0.31 cputime=3379.249 memavail=1412164 print_time=70582.438 buffer_time=0.000 print_stall=0 extruder: target=150 temp=180.6 pwm=0.000
Stats 70578.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=468208 bytes_read=7955705 bytes_retransmit=9 bytes_invalid=0 send_seq=72598 receive_seq=72598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999681 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=418872 bytes_read=1291700 bytes_retransmit=0 bytes_invalid=0 send_seq=69779 receive_seq=69779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998403 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441576 bytes_read=7702612 bytes_retransmit=9 bytes_invalid=0 send_seq=71194 receive_seq=71194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999454 adj=63999531 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=27.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423213 bytes_read=24377218 bytes_retransmit=9 bytes_invalid=0 send_seq=70132 receive_seq=70132 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999922 coil_temp=28.8 refs=0 mcu_temp=25.33 supply_voltage=3.013 sysload=0.31 cputime=3379.342 memavail=1411424 print_time=70583.438 buffer_time=0.000 print_stall=0 extruder: target=150 temp=179.5 pwm=0.000
Stats 70579.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=468410 bytes_read=7956144 bytes_retransmit=9 bytes_invalid=0 send_seq=72613 receive_seq=72613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999682 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418878 bytes_read=1291729 bytes_retransmit=0 bytes_invalid=0 send_seq=69780 receive_seq=69780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998408 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441610 bytes_read=7702761 bytes_retransmit=9 bytes_invalid=0 send_seq=71197 receive_seq=71197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999525 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=33.5 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=27.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423219 bytes_read=24377574 bytes_retransmit=9 bytes_invalid=0 send_seq=70133 receive_seq=70133 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999920 coil_temp=28.9 refs=0 mcu_temp=25.38 supply_voltage=3.013 sysload=0.29 cputime=3379.434 memavail=1411180 print_time=70584.439 buffer_time=0.000 print_stall=0 extruder: target=150 temp=177.6 pwm=0.000
Stats 70580.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=468612 bytes_read=7956612 bytes_retransmit=9 bytes_invalid=0 send_seq=72628 receive_seq=72628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999680 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418884 bytes_read=1291745 bytes_retransmit=0 bytes_invalid=0 send_seq=69781 receive_seq=69781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998417 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441644 bytes_read=7702939 bytes_retransmit=9 bytes_invalid=0 send_seq=71200 receive_seq=71200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999452 adj=63999521 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=33.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=28.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423225 bytes_read=24377930 bytes_retransmit=9 bytes_invalid=0 send_seq=70134 receive_seq=70134 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999919 coil_temp=29.0 refs=0 mcu_temp=25.42 supply_voltage=3.013 sysload=0.29 cputime=3379.513 memavail=1405408 print_time=70585.439 buffer_time=0.000 print_stall=0 extruder: target=150 temp=176.4 pwm=0.000
Stats 70581.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=468814 bytes_read=7957051 bytes_retransmit=9 bytes_invalid=0 send_seq=72643 receive_seq=72643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999677 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418890 bytes_read=1291761 bytes_retransmit=0 bytes_invalid=0 send_seq=69782 receive_seq=69782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998423 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441678 bytes_read=7703088 bytes_retransmit=9 bytes_invalid=0 send_seq=71203 receive_seq=71203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999520 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=28.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423231 bytes_read=24378286 bytes_retransmit=9 bytes_invalid=0 send_seq=70135 receive_seq=70135 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31999924 coil_temp=29.0 refs=0 mcu_temp=25.47 supply_voltage=3.013 sysload=0.29 cputime=3379.552 memavail=1411192 print_time=70586.440 buffer_time=0.000 print_stall=0 extruder: target=150 temp=175.1 pwm=0.000
Stats 70582.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=469032 bytes_read=7957495 bytes_retransmit=9 bytes_invalid=0 send_seq=72659 receive_seq=72659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999672 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418896 bytes_read=1291777 bytes_retransmit=0 bytes_invalid=0 send_seq=69783 receive_seq=69783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998415 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441712 bytes_read=7703251 bytes_retransmit=9 bytes_invalid=0 send_seq=71206 receive_seq=71206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999448 adj=63999516 Octopus_V1.1_F446: temp=27.4 EBB42_v1.2_T0: temp=33.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=28.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423237 bytes_read=24378642 bytes_retransmit=9 bytes_invalid=0 send_seq=70136 receive_seq=70136 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31999927 coil_temp=29.1 refs=0 mcu_temp=25.51 supply_voltage=3.013 sysload=0.29 cputime=3379.592 memavail=1411192 print_time=70587.440 buffer_time=0.000 print_stall=0 extruder: target=150 temp=173.9 pwm=0.000
Stats 70583.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=469234 bytes_read=7957978 bytes_retransmit=9 bytes_invalid=0 send_seq=72674 receive_seq=72674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999667 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418902 bytes_read=1291793 bytes_retransmit=0 bytes_invalid=0 send_seq=69784 receive_seq=69784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998412 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441746 bytes_read=7703429 bytes_retransmit=9 bytes_invalid=0 send_seq=71209 receive_seq=71209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999447 adj=63999515 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=33.4 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=29.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423243 bytes_read=24378998 bytes_retransmit=9 bytes_invalid=0 send_seq=70137 receive_seq=70137 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31999924 coil_temp=29.2 refs=0 mcu_temp=25.56 supply_voltage=3.013 sysload=0.29 cputime=3379.632 memavail=1410968 print_time=70588.441 buffer_time=0.000 print_stall=0 extruder: target=150 temp=171.6 pwm=0.000
Stats 70584.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=469436 bytes_read=7958417 bytes_retransmit=9 bytes_invalid=0 send_seq=72689 receive_seq=72689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=418908 bytes_read=1291809 bytes_retransmit=0 bytes_invalid=0 send_seq=69785 receive_seq=69785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998409 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441780 bytes_read=7703578 bytes_retransmit=9 bytes_invalid=0 send_seq=71212 receive_seq=71212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999445 adj=63999518 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=29.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423249 bytes_read=24379354 bytes_retransmit=9 bytes_invalid=0 send_seq=70138 receive_seq=70138 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999923 coil_temp=29.2 refs=0 mcu_temp=25.61 supply_voltage=3.013 sysload=0.27 cputime=3379.671 memavail=1409456 print_time=70589.441 buffer_time=0.000 print_stall=0 extruder: target=150 temp=170.5 pwm=0.000
Stats 70585.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=469638 bytes_read=7958856 bytes_retransmit=9 bytes_invalid=0 send_seq=72704 receive_seq=72704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418914 bytes_read=1291838 bytes_retransmit=0 bytes_invalid=0 send_seq=69786 receive_seq=69786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998407 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441814 bytes_read=7703727 bytes_retransmit=9 bytes_invalid=0 send_seq=71215 receive_seq=71215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999443 adj=63999517 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=29.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423255 bytes_read=24379710 bytes_retransmit=9 bytes_invalid=0 send_seq=70139 receive_seq=70139 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999922 coil_temp=29.3 refs=0 mcu_temp=25.67 supply_voltage=3.013 sysload=0.27 cputime=3379.736 memavail=1409456 print_time=70590.442 buffer_time=0.000 print_stall=0 extruder: target=150 temp=169.3 pwm=0.000
Stats 70586.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=469862 bytes_read=7959345 bytes_retransmit=9 bytes_invalid=0 send_seq=72721 receive_seq=72721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999657 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418920 bytes_read=1291854 bytes_retransmit=0 bytes_invalid=0 send_seq=69787 receive_seq=69787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998402 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441854 bytes_read=7703921 bytes_retransmit=9 bytes_invalid=0 send_seq=71219 receive_seq=71219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999443 adj=63999516 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=29.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423261 bytes_read=24380066 bytes_retransmit=9 bytes_invalid=0 send_seq=70140 receive_seq=70140 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999923 coil_temp=29.4 refs=0 mcu_temp=25.71 supply_voltage=3.013 sysload=0.27 cputime=3379.832 memavail=1409460 print_time=70591.443 buffer_time=0.000 print_stall=0 extruder: target=150 temp=167.6 pwm=0.000
Stats 70587.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=470064 bytes_read=7959784 bytes_retransmit=9 bytes_invalid=0 send_seq=72736 receive_seq=72736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418926 bytes_read=1291870 bytes_retransmit=0 bytes_invalid=0 send_seq=69788 receive_seq=69788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998412 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441888 bytes_read=7704084 bytes_retransmit=9 bytes_invalid=0 send_seq=71222 receive_seq=71222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999443 adj=63999517 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=30.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423267 bytes_read=24380422 bytes_retransmit=9 bytes_invalid=0 send_seq=70141 receive_seq=70141 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999923 coil_temp=29.4 refs=0 mcu_temp=25.77 supply_voltage=3.013 sysload=0.27 cputime=3379.924 memavail=1409460 print_time=70592.443 buffer_time=0.000 print_stall=0 extruder: target=150 temp=166.3 pwm=0.000
Stats 70588.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=470266 bytes_read=7960238 bytes_retransmit=9 bytes_invalid=0 send_seq=72751 receive_seq=72751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999661 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418932 bytes_read=1291886 bytes_retransmit=0 bytes_invalid=0 send_seq=69789 receive_seq=69789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998421 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441922 bytes_read=7704233 bytes_retransmit=9 bytes_invalid=0 send_seq=71225 receive_seq=71225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999445 adj=63999514 Octopus_V1.1_F446: temp=27.4 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=30.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423273 bytes_read=24380778 bytes_retransmit=9 bytes_invalid=0 send_seq=70142 receive_seq=70142 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999921 coil_temp=29.5 refs=0 mcu_temp=25.81 supply_voltage=3.013 sysload=0.27 cputime=3380.015 memavail=1409460 print_time=70593.443 buffer_time=0.000 print_stall=0 extruder: target=150 temp=164.9 pwm=0.000
Stats 70589.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=470468 bytes_read=7960706 bytes_retransmit=9 bytes_invalid=0 send_seq=72766 receive_seq=72766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=418938 bytes_read=1291902 bytes_retransmit=0 bytes_invalid=0 send_seq=69790 receive_seq=69790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998433 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441956 bytes_read=7704411 bytes_retransmit=9 bytes_invalid=0 send_seq=71228 receive_seq=71228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999446 adj=63999519 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=30.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423279 bytes_read=24381134 bytes_retransmit=9 bytes_invalid=0 send_seq=70143 receive_seq=70143 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999922 coil_temp=29.6 refs=0 mcu_temp=25.86 supply_voltage=3.013 sysload=0.24 cputime=3380.110 memavail=1409460 print_time=70594.443 buffer_time=0.000 print_stall=0 extruder: target=150 temp=163.4 pwm=0.000
Stats 70590.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=470670 bytes_read=7961145 bytes_retransmit=9 bytes_invalid=0 send_seq=72781 receive_seq=72781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999669 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000022 bytes_write=418944 bytes_read=1291931 bytes_retransmit=0 bytes_invalid=0 send_seq=69791 receive_seq=69791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998435 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=441990 bytes_read=7704560 bytes_retransmit=9 bytes_invalid=0 send_seq=71231 receive_seq=71231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999446 adj=63999513 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=30.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423285 bytes_read=24381474 bytes_retransmit=9 bytes_invalid=0 send_seq=70144 receive_seq=70144 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999916 coil_temp=29.6 refs=0 mcu_temp=25.91 supply_voltage=3.013 sysload=0.24 cputime=3380.204 memavail=1409460 print_time=70595.444 buffer_time=0.000 print_stall=0 extruder: target=150 temp=162.4 pwm=0.000
Stats 70591.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=470888 bytes_read=7961589 bytes_retransmit=9 bytes_invalid=0 send_seq=72797 receive_seq=72797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999678 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000022 bytes_write=418950 bytes_read=1291947 bytes_retransmit=0 bytes_invalid=0 send_seq=69792 receive_seq=69792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998445 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442024 bytes_read=7704704 bytes_retransmit=9 bytes_invalid=0 send_seq=71234 receive_seq=71234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999466 adj=63999512 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=31.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423291 bytes_read=24381830 bytes_retransmit=9 bytes_invalid=0 send_seq=70145 receive_seq=70145 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999915 coil_temp=29.7 refs=0 mcu_temp=25.95 supply_voltage=3.013 sysload=0.24 cputime=3380.299 memavail=1409460 print_time=70596.445 buffer_time=0.000 print_stall=0 extruder: target=150 temp=161.1 pwm=0.000
Stats 70592.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=471090 bytes_read=7962057 bytes_retransmit=9 bytes_invalid=0 send_seq=72812 receive_seq=72812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999681 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000022 bytes_write=418956 bytes_read=1291963 bytes_retransmit=0 bytes_invalid=0 send_seq=69793 receive_seq=69793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998437 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442058 bytes_read=7704887 bytes_retransmit=9 bytes_invalid=0 send_seq=71237 receive_seq=71237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999583 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=31.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423297 bytes_read=24382180 bytes_retransmit=9 bytes_invalid=0 send_seq=70146 receive_seq=70146 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999908 coil_temp=29.7 refs=0 mcu_temp=26.00 supply_voltage=3.013 sysload=0.24 cputime=3380.396 memavail=1409472 print_time=70597.445 buffer_time=0.000 print_stall=0 extruder: target=150 temp=159.6 pwm=0.000
Stats 70593.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=471292 bytes_read=7962511 bytes_retransmit=9 bytes_invalid=0 send_seq=72827 receive_seq=72827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999682 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000022 bytes_write=418962 bytes_read=1291979 bytes_retransmit=0 bytes_invalid=0 send_seq=69794 receive_seq=69794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998448 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442092 bytes_read=7705029 bytes_retransmit=9 bytes_invalid=0 send_seq=71240 receive_seq=71240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999464 adj=63999573 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=31.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423303 bytes_read=24382525 bytes_retransmit=9 bytes_invalid=0 send_seq=70147 receive_seq=70147 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999906 coil_temp=29.8 refs=0 mcu_temp=26.06 supply_voltage=3.013 sysload=0.24 cputime=3380.489 memavail=1409472 print_time=70598.446 buffer_time=0.000 print_stall=0 extruder: target=150 temp=158.5 pwm=0.000
Stats 70594.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=471494 bytes_read=7962964 bytes_retransmit=9 bytes_invalid=0 send_seq=72842 receive_seq=72842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999686 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000022 bytes_write=418968 bytes_read=1291995 bytes_retransmit=0 bytes_invalid=0 send_seq=69795 receive_seq=69795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998451 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442126 bytes_read=7705171 bytes_retransmit=9 bytes_invalid=0 send_seq=71243 receive_seq=71243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999569 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=32.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423309 bytes_read=24382869 bytes_retransmit=9 bytes_invalid=0 send_seq=70148 receive_seq=70148 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999908 coil_temp=29.8 refs=0 mcu_temp=26.10 supply_voltage=3.013 sysload=0.22 cputime=3380.580 memavail=1409232 print_time=70599.447 buffer_time=0.000 print_stall=0 extruder: target=150 temp=157.3 pwm=0.000
Stats 70595.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=471707 bytes_read=7963418 bytes_retransmit=9 bytes_invalid=0 send_seq=72857 receive_seq=72857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999689 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418974 bytes_read=1292024 bytes_retransmit=0 bytes_invalid=0 send_seq=69796 receive_seq=69796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998447 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442160 bytes_read=7705345 bytes_retransmit=9 bytes_invalid=0 send_seq=71246 receive_seq=71246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999557 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=32.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423315 bytes_read=24383214 bytes_retransmit=9 bytes_invalid=0 send_seq=70149 receive_seq=70149 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31999901 coil_temp=29.9 refs=0 mcu_temp=26.15 supply_voltage=3.013 sysload=0.22 cputime=3380.669 memavail=1408972 print_time=70600.447 buffer_time=0.000 print_stall=0 extruder: target=150 temp=156.0 pwm=0.000
Stats 70596.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=471909 bytes_read=7963857 bytes_retransmit=9 bytes_invalid=0 send_seq=72872 receive_seq=72872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999689 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418980 bytes_read=1292040 bytes_retransmit=0 bytes_invalid=0 send_seq=69797 receive_seq=69797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998352 adj=49998449 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442194 bytes_read=7705494 bytes_retransmit=9 bytes_invalid=0 send_seq=71249 receive_seq=71249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999462 adj=63999548 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=32.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423321 bytes_read=24383559 bytes_retransmit=9 bytes_invalid=0 send_seq=70150 receive_seq=70150 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999905 coil_temp=29.9 refs=0 mcu_temp=26.19 supply_voltage=3.013 sysload=0.22 cputime=3380.760 memavail=1408972 print_time=70601.448 buffer_time=0.000 print_stall=0 extruder: target=150 temp=154.5 pwm=0.000
Stats 70597.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=472111 bytes_read=7964310 bytes_retransmit=9 bytes_invalid=0 send_seq=72887 receive_seq=72887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999687 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418992 bytes_read=1292072 bytes_retransmit=0 bytes_invalid=0 send_seq=69799 receive_seq=69799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998353 adj=49998471 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442228 bytes_read=7705657 bytes_retransmit=9 bytes_invalid=0 send_seq=71252 receive_seq=71252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999461 adj=63999545 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=32.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423327 bytes_read=24383904 bytes_retransmit=9 bytes_invalid=0 send_seq=70151 receive_seq=70151 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31999903 coil_temp=30.0 refs=0 mcu_temp=26.23 supply_voltage=3.013 sysload=0.22 cputime=3380.850 memavail=1403420 print_time=70602.449 buffer_time=0.000 print_stall=0 extruder: target=150 temp=153.5 pwm=0.000
Stats 70598.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=472313 bytes_read=7964779 bytes_retransmit=9 bytes_invalid=0 send_seq=72902 receive_seq=72902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999680 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=418998 bytes_read=1292088 bytes_retransmit=0 bytes_invalid=0 send_seq=69800 receive_seq=69800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998349 adj=49998481 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442262 bytes_read=7705835 bytes_retransmit=9 bytes_invalid=0 send_seq=71255 receive_seq=71255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999458 adj=63999541 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=33.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423333 bytes_read=24384249 bytes_retransmit=9 bytes_invalid=0 send_seq=70152 receive_seq=70152 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31999902 coil_temp=30.0 refs=0 mcu_temp=26.27 supply_voltage=3.013 sysload=0.22 cputime=3380.891 memavail=1409224 print_time=70603.449 buffer_time=0.000 print_stall=0 extruder: target=150 temp=152.2 pwm=0.000
Stats 70599.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=472531 bytes_read=7965216 bytes_retransmit=9 bytes_invalid=0 send_seq=72918 receive_seq=72918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999672 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=419004 bytes_read=1292104 bytes_retransmit=0 bytes_invalid=0 send_seq=69801 receive_seq=69801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998470 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442326 bytes_read=7705994 bytes_retransmit=9 bytes_invalid=0 send_seq=71260 receive_seq=71260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999456 adj=63999541 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=33.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423339 bytes_read=24384594 bytes_retransmit=9 bytes_invalid=0 send_seq=70153 receive_seq=70153 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999864 adj=31999902 coil_temp=30.0 refs=0 mcu_temp=26.31 supply_voltage=3.013 sysload=0.21 cputime=3380.932 memavail=1409224 print_time=70604.450 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.160
Stats 70600.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=472733 bytes_read=7965666 bytes_retransmit=9 bytes_invalid=0 send_seq=72933 receive_seq=72933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999663 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=419010 bytes_read=1292133 bytes_retransmit=0 bytes_invalid=0 send_seq=69802 receive_seq=69802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998460 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442375 bytes_read=7706148 bytes_retransmit=9 bytes_invalid=0 send_seq=71264 receive_seq=71264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999454 adj=63999546 Octopus_V1.1_F446: temp=28.3 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=33.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423345 bytes_read=24384941 bytes_retransmit=9 bytes_invalid=0 send_seq=70154 receive_seq=70154 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999863 adj=31999901 coil_temp=30.1 refs=0 mcu_temp=26.38 supply_voltage=3.013 sysload=0.21 cputime=3380.971 memavail=1409224 print_time=70605.451 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.061
Stats 70601.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=472935 bytes_read=7966120 bytes_retransmit=9 bytes_invalid=0 send_seq=72948 receive_seq=72948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999657 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=419016 bytes_read=1292149 bytes_retransmit=0 bytes_invalid=0 send_seq=69803 receive_seq=69803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998456 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442422 bytes_read=7706331 bytes_retransmit=9 bytes_invalid=0 send_seq=71268 receive_seq=71268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999451 adj=63999552 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=33.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=33.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423351 bytes_read=24385297 bytes_retransmit=9 bytes_invalid=0 send_seq=70155 receive_seq=70155 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999863 adj=31999902 coil_temp=30.1 refs=0 mcu_temp=26.41 supply_voltage=3.013 sysload=0.21 cputime=3381.012 memavail=1409232 print_time=70606.451 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.055
Stats 70602.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=473137 bytes_read=7966559 bytes_retransmit=9 bytes_invalid=0 send_seq=72963 receive_seq=72963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999649 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=419022 bytes_read=1292165 bytes_retransmit=0 bytes_invalid=0 send_seq=69804 receive_seq=69804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998441 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442512 bytes_read=7706509 bytes_retransmit=9 bytes_invalid=0 send_seq=71274 receive_seq=71274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999449 adj=63999550 Octopus_V1.1_F446: temp=28.3 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=34.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423357 bytes_read=24385653 bytes_retransmit=9 bytes_invalid=0 send_seq=70156 receive_seq=70156 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999862 adj=31999918 coil_temp=30.1 refs=0 mcu_temp=26.46 supply_voltage=3.013 sysload=0.21 cputime=3381.057 memavail=1409232 print_time=70607.451 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.5 pwm=0.284
Stats 70603.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=473350 bytes_read=7967027 bytes_retransmit=9 bytes_invalid=0 send_seq=72978 receive_seq=72978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=419028 bytes_read=1292181 bytes_retransmit=0 bytes_invalid=0 send_seq=69805 receive_seq=69805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998468 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442576 bytes_read=7706668 bytes_retransmit=9 bytes_invalid=0 send_seq=71279 receive_seq=71279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999448 adj=63999541 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=34.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423369 bytes_read=24386025 bytes_retransmit=9 bytes_invalid=0 send_seq=70158 receive_seq=70158 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31999907 coil_temp=30.2 refs=0 mcu_temp=26.50 supply_voltage=3.013 sysload=0.21 cputime=3381.150 memavail=1409484 print_time=70608.452 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.098
Stats 70604.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=473552 bytes_read=7967481 bytes_retransmit=9 bytes_invalid=0 send_seq=72993 receive_seq=72993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=419034 bytes_read=1292197 bytes_retransmit=0 bytes_invalid=0 send_seq=69806 receive_seq=69806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998349 adj=49998501 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442623 bytes_read=7706851 bytes_retransmit=9 bytes_invalid=0 send_seq=71283 receive_seq=71283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999447 adj=63999511 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=34.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423375 bytes_read=24386381 bytes_retransmit=9 bytes_invalid=0 send_seq=70159 receive_seq=70159 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31999889 coil_temp=30.2 refs=0 mcu_temp=26.54 supply_voltage=3.013 sysload=0.19 cputime=3381.241 memavail=1409484 print_time=70609.452 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.000
Stats 70605.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=473754 bytes_read=7967920 bytes_retransmit=9 bytes_invalid=0 send_seq=73008 receive_seq=73008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419040 bytes_read=1292226 bytes_retransmit=0 bytes_invalid=0 send_seq=69807 receive_seq=69807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998351 adj=49998556 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442704 bytes_read=7707015 bytes_retransmit=9 bytes_invalid=0 send_seq=71289 receive_seq=71289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999446 adj=63999483 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=34.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423381 bytes_read=24386737 bytes_retransmit=9 bytes_invalid=0 send_seq=70160 receive_seq=70160 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31999869 coil_temp=30.3 refs=0 mcu_temp=26.58 supply_voltage=3.013 sysload=0.19 cputime=3381.331 memavail=1409484 print_time=70610.453 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.0 pwm=0.387
Stats 70606.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=473956 bytes_read=7968373 bytes_retransmit=9 bytes_invalid=0 send_seq=73023 receive_seq=73023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999668 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419046 bytes_read=1292242 bytes_retransmit=0 bytes_invalid=0 send_seq=69808 receive_seq=69808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998562 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=442769 bytes_read=7707174 bytes_retransmit=9 bytes_invalid=0 send_seq=71294 receive_seq=71294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999447 adj=63999464 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=34.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423387 bytes_read=24387093 bytes_retransmit=9 bytes_invalid=0 send_seq=70161 receive_seq=70161 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31999863 coil_temp=30.3 refs=0 mcu_temp=26.62 supply_voltage=3.013 sysload=0.19 cputime=3381.421 memavail=1409484 print_time=70611.453 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.3 pwm=0.025
Stats 70607.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=474174 bytes_read=7968832 bytes_retransmit=9 bytes_invalid=0 send_seq=73039 receive_seq=73039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419052 bytes_read=1292258 bytes_retransmit=0 bytes_invalid=0 send_seq=69809 receive_seq=69809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998358 adj=49998555 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=442803 bytes_read=7707366 bytes_retransmit=9 bytes_invalid=0 send_seq=71297 receive_seq=71297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999446 adj=63999449 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=33.8 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=35.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423393 bytes_read=24387449 bytes_retransmit=9 bytes_invalid=0 send_seq=70162 receive_seq=70162 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31999849 coil_temp=30.3 refs=0 mcu_temp=26.67 supply_voltage=3.013 sysload=0.19 cputime=3381.511 memavail=1409484 print_time=70612.455 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.025
Stats 70608.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=474376 bytes_read=7969286 bytes_retransmit=9 bytes_invalid=0 send_seq=73054 receive_seq=73054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419058 bytes_read=1292274 bytes_retransmit=0 bytes_invalid=0 send_seq=69810 receive_seq=69810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998358 adj=49998602 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=442852 bytes_read=7707520 bytes_retransmit=9 bytes_invalid=0 send_seq=71301 receive_seq=71301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999445 adj=63999504 Octopus_V1.1_F446: temp=28.5 EBB42_v1.2_T0: temp=33.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=35.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423399 bytes_read=24387805 bytes_retransmit=9 bytes_invalid=0 send_seq=70163 receive_seq=70163 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31999882 coil_temp=30.3 refs=0 mcu_temp=26.70 supply_voltage=3.013 sysload=0.19 cputime=3381.601 memavail=1409484 print_time=70613.456 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.203
Stats 70609.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=474578 bytes_read=7969754 bytes_retransmit=9 bytes_invalid=0 send_seq=73069 receive_seq=73069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999651 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419064 bytes_read=1292290 bytes_retransmit=0 bytes_invalid=0 send_seq=69811 receive_seq=69811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998358 adj=49998589 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=442933 bytes_read=7707684 bytes_retransmit=9 bytes_invalid=0 send_seq=71307 receive_seq=71307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999444 adj=63999530 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=35.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423405 bytes_read=24388161 bytes_retransmit=9 bytes_invalid=0 send_seq=70164 receive_seq=70164 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31999896 coil_temp=30.4 refs=0 mcu_temp=26.73 supply_voltage=3.013 sysload=0.17 cputime=3381.693 memavail=1409484 print_time=70614.456 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.149
Stats 70610.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=474780 bytes_read=7970193 bytes_retransmit=9 bytes_invalid=0 send_seq=73084 receive_seq=73084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999649 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=419070 bytes_read=1292319 bytes_retransmit=0 bytes_invalid=0 send_seq=69812 receive_seq=69812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998357 adj=49998567 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=442982 bytes_read=7707867 bytes_retransmit=9 bytes_invalid=0 send_seq=71311 receive_seq=71311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999444 adj=63999560 Octopus_V1.1_F446: temp=28.6 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=35.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423411 bytes_read=24388517 bytes_retransmit=9 bytes_invalid=0 send_seq=70165 receive_seq=70165 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31999914 coil_temp=30.4 refs=0 mcu_temp=26.77 supply_voltage=3.013 sysload=0.17 cputime=3381.784 memavail=1409484 print_time=70615.457 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.050
Stats 70611.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=474982 bytes_read=7970632 bytes_retransmit=9 bytes_invalid=0 send_seq=73099 receive_seq=73099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999642 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=419076 bytes_read=1292335 bytes_retransmit=0 bytes_invalid=0 send_seq=69813 receive_seq=69813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998357 adj=49998541 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443026 bytes_read=7708016 bytes_retransmit=9 bytes_invalid=0 send_seq=71314 receive_seq=71314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999451 adj=63999565 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=36.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423417 bytes_read=24388873 bytes_retransmit=9 bytes_invalid=0 send_seq=70166 receive_seq=70166 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31999917 coil_temp=30.5 refs=0 mcu_temp=26.80 supply_voltage=3.013 sysload=0.17 cputime=3381.875 memavail=1409484 print_time=70616.458 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.181
Stats 70612.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=475200 bytes_read=7971105 bytes_retransmit=9 bytes_invalid=0 send_seq=73115 receive_seq=73115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999641 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=419082 bytes_read=1292351 bytes_retransmit=0 bytes_invalid=0 send_seq=69814 receive_seq=69814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998537 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443076 bytes_read=7708184 bytes_retransmit=9 bytes_invalid=0 send_seq=71318 receive_seq=71318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999459 adj=63999723 Octopus_V1.1_F446: temp=28.7 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=36.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423423 bytes_read=24389229 bytes_retransmit=9 bytes_invalid=0 send_seq=70167 receive_seq=70167 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31999934 coil_temp=30.5 refs=0 mcu_temp=26.84 supply_voltage=3.013 sysload=0.17 cputime=3381.969 memavail=1409224 print_time=70617.458 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.250
Stats 70613.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=475402 bytes_read=7971559 bytes_retransmit=9 bytes_invalid=0 send_seq=73130 receive_seq=73130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999640 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=419088 bytes_read=1292367 bytes_retransmit=0 bytes_invalid=0 send_seq=69815 receive_seq=69815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998498 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443138 bytes_read=7708372 bytes_retransmit=9 bytes_invalid=0 send_seq=71323 receive_seq=71323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999457 adj=63999808 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=36.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423429 bytes_read=24389585 bytes_retransmit=9 bytes_invalid=0 send_seq=70168 receive_seq=70168 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31999935 coil_temp=30.5 refs=0 mcu_temp=26.88 supply_voltage=3.013 sysload=0.17 cputime=3382.061 memavail=1409272 print_time=70618.459 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.000
Stats 70614.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=475604 bytes_read=7971998 bytes_retransmit=9 bytes_invalid=0 send_seq=73145 receive_seq=73145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999640 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=419094 bytes_read=1292383 bytes_retransmit=0 bytes_invalid=0 send_seq=69816 receive_seq=69816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998485 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443203 bytes_read=7708531 bytes_retransmit=9 bytes_invalid=0 send_seq=71328 receive_seq=71328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999455 adj=63999730 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=36.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423435 bytes_read=24389941 bytes_retransmit=9 bytes_invalid=0 send_seq=70169 receive_seq=70169 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999856 adj=31999920 coil_temp=30.5 refs=0 mcu_temp=26.93 supply_voltage=3.013 sysload=0.16 cputime=3382.150 memavail=1408304 print_time=70619.459 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.262
Stats 70615.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=475806 bytes_read=7972466 bytes_retransmit=9 bytes_invalid=0 send_seq=73160 receive_seq=73160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999635 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000016 bytes_write=419100 bytes_read=1292412 bytes_retransmit=0 bytes_invalid=0 send_seq=69817 receive_seq=69817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998350 adj=49998482 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443269 bytes_read=7708690 bytes_retransmit=9 bytes_invalid=0 send_seq=71333 receive_seq=71333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999453 adj=63999671 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=37.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423441 bytes_read=24390297 bytes_retransmit=9 bytes_invalid=0 send_seq=70170 receive_seq=70170 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999854 adj=31999903 coil_temp=30.6 refs=0 mcu_temp=26.97 supply_voltage=3.013 sysload=0.16 cputime=3382.196 memavail=1409556 print_time=70620.460 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.290
Stats 70616.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=476019 bytes_read=7972905 bytes_retransmit=9 bytes_invalid=0 send_seq=73175 receive_seq=73175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999629 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000016 bytes_write=419106 bytes_read=1292428 bytes_retransmit=0 bytes_invalid=0 send_seq=69818 receive_seq=69818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998422 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443331 bytes_read=7708878 bytes_retransmit=9 bytes_invalid=0 send_seq=71338 receive_seq=71338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999638 Octopus_V1.1_F446: temp=29.0 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=37.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423447 bytes_read=24390653 bytes_retransmit=9 bytes_invalid=0 send_seq=70171 receive_seq=70171 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999852 adj=31999891 coil_temp=30.6 refs=0 mcu_temp=27.01 supply_voltage=3.013 sysload=0.16 cputime=3382.235 memavail=1409556 print_time=70621.461 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.000
Stats 70617.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=476221 bytes_read=7973344 bytes_retransmit=9 bytes_invalid=0 send_seq=73190 receive_seq=73190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999624 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000016 bytes_write=419112 bytes_read=1292444 bytes_retransmit=0 bytes_invalid=0 send_seq=69819 receive_seq=69819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998400 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443396 bytes_read=7709051 bytes_retransmit=9 bytes_invalid=0 send_seq=71343 receive_seq=71343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999446 adj=63999609 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=37.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423453 bytes_read=24391027 bytes_retransmit=9 bytes_invalid=0 send_seq=70172 receive_seq=70172 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999851 adj=31999888 coil_temp=30.6 refs=0 mcu_temp=27.05 supply_voltage=3.013 sysload=0.16 cputime=3382.274 memavail=1409556 print_time=70622.461 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.303
Stats 70618.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=476423 bytes_read=7973827 bytes_retransmit=9 bytes_invalid=0 send_seq=73205 receive_seq=73205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999622 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000016 bytes_write=419118 bytes_read=1292460 bytes_retransmit=0 bytes_invalid=0 send_seq=69820 receive_seq=69820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998400 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443473 bytes_read=7709210 bytes_retransmit=9 bytes_invalid=0 send_seq=71348 receive_seq=71348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999445 adj=63999577 Octopus_V1.1_F446: temp=29.0 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=37.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423459 bytes_read=24391383 bytes_retransmit=9 bytes_invalid=0 send_seq=70173 receive_seq=70173 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999849 adj=31999886 coil_temp=30.7 refs=0 mcu_temp=27.09 supply_voltage=3.013 sysload=0.16 cputime=3382.313 memavail=1408556 print_time=70623.462 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.316
Stats 70619.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=476625 bytes_read=7974266 bytes_retransmit=9 bytes_invalid=0 send_seq=73220 receive_seq=73220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999617 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000016 bytes_write=419124 bytes_read=1292475 bytes_retransmit=0 bytes_invalid=0 send_seq=69821 receive_seq=69821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998362 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443535 bytes_read=7709398 bytes_retransmit=9 bytes_invalid=0 send_seq=71353 receive_seq=71353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999442 adj=63999564 Octopus_V1.1_F446: temp=28.9 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=37.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423465 bytes_read=24391739 bytes_retransmit=9 bytes_invalid=0 send_seq=70174 receive_seq=70174 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999848 adj=31999876 coil_temp=30.7 refs=0 mcu_temp=27.13 supply_voltage=3.013 sysload=0.15 cputime=3382.353 memavail=1408332 print_time=70624.462 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.8 pwm=0.000
Stats 70620.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=476843 bytes_read=7974710 bytes_retransmit=9 bytes_invalid=0 send_seq=73236 receive_seq=73236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999617 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419130 bytes_read=1292503 bytes_retransmit=0 bytes_invalid=0 send_seq=69822 receive_seq=69822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998357 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443584 bytes_read=7709552 bytes_retransmit=9 bytes_invalid=0 send_seq=71357 receive_seq=71357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999441 adj=63999548 Octopus_V1.1_F446: temp=29.0 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=38.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423471 bytes_read=24392095 bytes_retransmit=9 bytes_invalid=0 send_seq=70175 receive_seq=70175 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31999885 coil_temp=30.7 refs=0 mcu_temp=27.19 supply_voltage=3.013 sysload=0.15 cputime=3382.442 memavail=1408332 print_time=70625.463 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.5 pwm=0.114
Stats 70621.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=477045 bytes_read=7975178 bytes_retransmit=9 bytes_invalid=0 send_seq=73251 receive_seq=73251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999616 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419136 bytes_read=1292518 bytes_retransmit=0 bytes_invalid=0 send_seq=69823 receive_seq=69823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998393 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443650 bytes_read=7709711 bytes_retransmit=9 bytes_invalid=0 send_seq=71362 receive_seq=71362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999439 adj=63999542 Octopus_V1.1_F446: temp=29.1 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=38.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423477 bytes_read=24392451 bytes_retransmit=9 bytes_invalid=0 send_seq=70176 receive_seq=70176 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999849 adj=31999916 coil_temp=30.7 refs=0 mcu_temp=27.23 supply_voltage=3.013 sysload=0.15 cputime=3382.531 memavail=1408332 print_time=70626.464 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.2 pwm=0.374
Stats 70622.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=477247 bytes_read=7975615 bytes_retransmit=9 bytes_invalid=0 send_seq=73266 receive_seq=73266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999614 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419142 bytes_read=1292533 bytes_retransmit=0 bytes_invalid=0 send_seq=69824 receive_seq=69824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998453 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443714 bytes_read=7709913 bytes_retransmit=9 bytes_invalid=0 send_seq=71367 receive_seq=71367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999439 adj=63999535 Octopus_V1.1_F446: temp=29.1 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=38.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423483 bytes_read=24392807 bytes_retransmit=9 bytes_invalid=0 send_seq=70177 receive_seq=70177 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999847 adj=31999898 coil_temp=30.8 refs=0 mcu_temp=27.27 supply_voltage=3.013 sysload=0.15 cputime=3382.622 memavail=1408332 print_time=70627.464 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.7 pwm=0.045
Stats 70623.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=477449 bytes_read=7976062 bytes_retransmit=9 bytes_invalid=0 send_seq=73281 receive_seq=73281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999611 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419148 bytes_read=1292548 bytes_retransmit=0 bytes_invalid=0 send_seq=69825 receive_seq=69825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998488 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443763 bytes_read=7710067 bytes_retransmit=9 bytes_invalid=0 send_seq=71371 receive_seq=71371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999543 Octopus_V1.1_F446: temp=29.1 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=38.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423489 bytes_read=24393163 bytes_retransmit=9 bytes_invalid=0 send_seq=70178 receive_seq=70178 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31999881 coil_temp=30.8 refs=0 mcu_temp=27.30 supply_voltage=3.013 sysload=0.15 cputime=3382.711 memavail=1408332 print_time=70628.465 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.127
Stats 70624.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=477667 bytes_read=7976532 bytes_retransmit=9 bytes_invalid=0 send_seq=73297 receive_seq=73297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419154 bytes_read=1292564 bytes_retransmit=0 bytes_invalid=0 send_seq=69826 receive_seq=69826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998516 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443828 bytes_read=7710226 bytes_retransmit=9 bytes_invalid=0 send_seq=71376 receive_seq=71376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999437 adj=63999564 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=39.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423495 bytes_read=24393519 bytes_retransmit=9 bytes_invalid=0 send_seq=70179 receive_seq=70179 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999844 adj=31999878 coil_temp=30.8 refs=0 mcu_temp=27.34 supply_voltage=3.013 sysload=0.13 cputime=3382.799 memavail=1408092 print_time=70629.465 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.275
Stats 70625.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=477869 bytes_read=7976971 bytes_retransmit=9 bytes_invalid=0 send_seq=73312 receive_seq=73312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999605 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=419160 bytes_read=1292593 bytes_retransmit=0 bytes_invalid=0 send_seq=69827 receive_seq=69827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998513 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443900 bytes_read=7710414 bytes_retransmit=9 bytes_invalid=0 send_seq=71381 receive_seq=71381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999564 Octopus_V1.1_F446: temp=29.3 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=39.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423501 bytes_read=24393875 bytes_retransmit=9 bytes_invalid=0 send_seq=70180 receive_seq=70180 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999844 adj=31999876 coil_temp=30.9 refs=0 mcu_temp=27.37 supply_voltage=3.013 sysload=0.13 cputime=3382.888 memavail=1408092 print_time=70630.466 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
Stats 70626.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=478071 bytes_read=7977410 bytes_retransmit=9 bytes_invalid=0 send_seq=73327 receive_seq=73327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999602 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=419166 bytes_read=1292609 bytes_retransmit=0 bytes_invalid=0 send_seq=69828 receive_seq=69828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998349 adj=49998518 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=443964 bytes_read=7710573 bytes_retransmit=9 bytes_invalid=0 send_seq=71386 receive_seq=71386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999605 Octopus_V1.1_F446: temp=29.3 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=39.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423507 bytes_read=24394231 bytes_retransmit=9 bytes_invalid=0 send_seq=70181 receive_seq=70181 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31999893 coil_temp=30.9 refs=0 mcu_temp=27.39 supply_voltage=3.013 sysload=0.13 cputime=3382.977 memavail=1408092 print_time=70631.467 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.222
Stats 70627.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=478273 bytes_read=7977878 bytes_retransmit=9 bytes_invalid=0 send_seq=73342 receive_seq=73342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999604 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=419172 bytes_read=1292625 bytes_retransmit=0 bytes_invalid=0 send_seq=69829 receive_seq=69829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998353 adj=49998577 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=444014 bytes_read=7710741 bytes_retransmit=9 bytes_invalid=0 send_seq=71390 receive_seq=71390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999603 Octopus_V1.1_F446: temp=29.4 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=39.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423513 bytes_read=24394587 bytes_retransmit=9 bytes_invalid=0 send_seq=70182 receive_seq=70182 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999842 adj=31999888 coil_temp=30.9 refs=0 mcu_temp=27.43 supply_voltage=3.013 sysload=0.13 cputime=3383.068 memavail=1408092 print_time=70632.467 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.328
Stats 70628.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=478491 bytes_read=7978337 bytes_retransmit=9 bytes_invalid=0 send_seq=73358 receive_seq=73358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999603 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=419178 bytes_read=1292641 bytes_retransmit=0 bytes_invalid=0 send_seq=69830 receive_seq=69830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998600 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=444078 bytes_read=7710929 bytes_retransmit=9 bytes_invalid=0 send_seq=71395 receive_seq=71395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999437 adj=63999584 Octopus_V1.1_F446: temp=29.4 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=39.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423519 bytes_read=24394943 bytes_retransmit=9 bytes_invalid=0 send_seq=70183 receive_seq=70183 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999841 adj=31999875 coil_temp=31.0 refs=0 mcu_temp=27.45 supply_voltage=3.013 sysload=0.13 cputime=3383.157 memavail=1408092 print_time=70633.468 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.031
Stats 70629.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=478693 bytes_read=7978776 bytes_retransmit=9 bytes_invalid=0 send_seq=73373 receive_seq=73373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999608 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=419184 bytes_read=1292657 bytes_retransmit=0 bytes_invalid=0 send_seq=69831 receive_seq=69831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998356 adj=49998610 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=444142 bytes_read=7711088 bytes_retransmit=9 bytes_invalid=0 send_seq=71400 receive_seq=71400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999435 adj=63999572 Octopus_V1.1_F446: temp=29.4 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=40.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423525 bytes_read=24395299 bytes_retransmit=9 bytes_invalid=0 send_seq=70184 receive_seq=70184 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999839 adj=31999865 coil_temp=31.0 refs=0 mcu_temp=27.49 supply_voltage=3.013 sysload=0.12 cputime=3383.245 memavail=1408292 print_time=70634.468 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.237
Stats 70630.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=478895 bytes_read=7979244 bytes_retransmit=9 bytes_invalid=0 send_seq=73388 receive_seq=73388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=419190 bytes_read=1292686 bytes_retransmit=0 bytes_invalid=0 send_seq=69832 receive_seq=69832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998565 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=444207 bytes_read=7711247 bytes_retransmit=9 bytes_invalid=0 send_seq=71405 receive_seq=71405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999434 adj=63999529 Octopus_V1.1_F446: temp=29.5 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=40.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423531 bytes_read=24395655 bytes_retransmit=9 bytes_invalid=0 send_seq=70185 receive_seq=70185 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31999842 coil_temp=31.1 refs=0 mcu_temp=27.51 supply_voltage=3.013 sysload=0.12 cputime=3383.333 memavail=1408364 print_time=70635.469 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.182
Stats 70631.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=479097 bytes_read=7979683 bytes_retransmit=9 bytes_invalid=0 send_seq=73403 receive_seq=73403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999611 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=419196 bytes_read=1292702 bytes_retransmit=0 bytes_invalid=0 send_seq=69833 receive_seq=69833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998524 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=444269 bytes_read=7711435 bytes_retransmit=9 bytes_invalid=0 send_seq=71410 receive_seq=71410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999434 adj=63999515 Octopus_V1.1_F446: temp=29.6 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=40.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423537 bytes_read=24396011 bytes_retransmit=9 bytes_invalid=0 send_seq=70186 receive_seq=70186 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999844 adj=31999949 coil_temp=31.1 refs=0 mcu_temp=27.55 supply_voltage=3.013 sysload=0.12 cputime=3383.422 memavail=1408364 print_time=70636.469 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.000
Stats 70632.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=479299 bytes_read=7980122 bytes_retransmit=9 bytes_invalid=0 send_seq=73418 receive_seq=73418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999612 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=419202 bytes_read=1292718 bytes_retransmit=0 bytes_invalid=0 send_seq=69834 receive_seq=69834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998350 adj=49998476 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444344 bytes_read=7711608 bytes_retransmit=9 bytes_invalid=0 send_seq=71415 receive_seq=71415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999433 adj=63999514 Octopus_V1.1_F446: temp=29.6 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=40.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423543 bytes_read=24396367 bytes_retransmit=9 bytes_invalid=0 send_seq=70187 receive_seq=70187 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999842 adj=31999924 coil_temp=31.2 refs=0 mcu_temp=27.58 supply_voltage=3.013 sysload=0.12 cputime=3383.483 memavail=1409380 print_time=70637.469 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.355
Stats 70633.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=479517 bytes_read=7980610 bytes_retransmit=9 bytes_invalid=0 send_seq=73434 receive_seq=73434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999605 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=419208 bytes_read=1292734 bytes_retransmit=0 bytes_invalid=0 send_seq=69835 receive_seq=69835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998416 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444393 bytes_read=7711776 bytes_retransmit=9 bytes_invalid=0 send_seq=71419 receive_seq=71419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999431 adj=63999517 Octopus_V1.1_F446: temp=29.7 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=40.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423549 bytes_read=24396723 bytes_retransmit=9 bytes_invalid=0 send_seq=70188 receive_seq=70188 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999841 adj=31999882 coil_temp=31.2 refs=0 mcu_temp=27.62 supply_voltage=3.013 sysload=0.12 cputime=3383.523 memavail=1409380 print_time=70638.470 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.212
Stats 70634.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=479719 bytes_read=7981049 bytes_retransmit=9 bytes_invalid=0 send_seq=73449 receive_seq=73449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999599 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=419214 bytes_read=1292750 bytes_retransmit=0 bytes_invalid=0 send_seq=69836 receive_seq=69836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998399 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444440 bytes_read=7711945 bytes_retransmit=9 bytes_invalid=0 send_seq=71423 receive_seq=71423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999430 adj=63999533 Octopus_V1.1_F446: temp=29.8 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=40.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423555 bytes_read=24397079 bytes_retransmit=9 bytes_invalid=0 send_seq=70189 receive_seq=70189 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999838 adj=31999885 coil_temp=31.2 refs=0 mcu_temp=27.70 supply_voltage=3.013 sysload=0.11 cputime=3383.563 memavail=1408920 print_time=70639.470 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.5 pwm=0.000
Stats 70635.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=479921 bytes_read=7981488 bytes_retransmit=9 bytes_invalid=0 send_seq=73464 receive_seq=73464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999593 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=419220 bytes_read=1292779 bytes_retransmit=0 bytes_invalid=0 send_seq=69837 receive_seq=69837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998382 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444521 bytes_read=7712109 bytes_retransmit=9 bytes_invalid=0 send_seq=71429 receive_seq=71429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999428 adj=63999561 Octopus_V1.1_F446: temp=29.8 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=41.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423561 bytes_read=24397435 bytes_retransmit=9 bytes_invalid=0 send_seq=70190 receive_seq=70190 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999836 adj=31999869 coil_temp=31.3 refs=0 mcu_temp=27.74 supply_voltage=3.013 sysload=0.11 cputime=3383.603 memavail=1408920 print_time=70640.471 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.347
Stats 70636.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=480123 bytes_read=7981956 bytes_retransmit=9 bytes_invalid=0 send_seq=73479 receive_seq=73479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999593 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=419226 bytes_read=1292795 bytes_retransmit=0 bytes_invalid=0 send_seq=69838 receive_seq=69838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998363 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444597 bytes_read=7712282 bytes_retransmit=9 bytes_invalid=0 send_seq=71434 receive_seq=71434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999428 adj=63999566 Octopus_V1.1_F446: temp=29.6 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=41.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423567 bytes_read=24397791 bytes_retransmit=9 bytes_invalid=0 send_seq=70191 receive_seq=70191 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999833 adj=31999856 coil_temp=31.3 refs=0 mcu_temp=27.78 supply_voltage=3.013 sysload=0.11 cputime=3383.644 memavail=1408420 print_time=70641.472 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.149
Stats 70637.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=480336 bytes_read=7982395 bytes_retransmit=9 bytes_invalid=0 send_seq=73494 receive_seq=73494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999586 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=419232 bytes_read=1292811 bytes_retransmit=0 bytes_invalid=0 send_seq=69839 receive_seq=69839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998329 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=444644 bytes_read=7712465 bytes_retransmit=9 bytes_invalid=0 send_seq=71438 receive_seq=71438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999425 adj=63999567 Octopus_V1.1_F446: temp=29.7 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=41.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423573 bytes_read=24398147 bytes_retransmit=9 bytes_invalid=0 send_seq=70192 receive_seq=70192 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31999836 coil_temp=31.4 refs=0 mcu_temp=27.81 supply_voltage=3.013 sysload=0.11 cputime=3383.716 memavail=1408420 print_time=70642.472 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.000
Stats 70638.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=480538 bytes_read=7982849 bytes_retransmit=9 bytes_invalid=0 send_seq=73509 receive_seq=73509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999587 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=419238 bytes_read=1292827 bytes_retransmit=0 bytes_invalid=0 send_seq=69840 receive_seq=69840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998403 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=444724 bytes_read=7712629 bytes_retransmit=9 bytes_invalid=0 send_seq=71444 receive_seq=71444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999425 adj=63999569 Octopus_V1.1_F446: temp=29.9 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=41.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423579 bytes_read=24398503 bytes_retransmit=9 bytes_invalid=0 send_seq=70193 receive_seq=70193 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999831 adj=31999855 coil_temp=31.4 refs=0 mcu_temp=27.84 supply_voltage=3.013 sysload=0.11 cputime=3383.807 memavail=1408420 print_time=70643.473 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.359
Stats 70639.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=480740 bytes_read=7983317 bytes_retransmit=9 bytes_invalid=0 send_seq=73524 receive_seq=73524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999600 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=419244 bytes_read=1292843 bytes_retransmit=0 bytes_invalid=0 send_seq=69841 receive_seq=69841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998426 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=444789 bytes_read=7712802 bytes_retransmit=9 bytes_invalid=0 send_seq=71449 receive_seq=71449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999430 adj=63999556 Octopus_V1.1_F446: temp=29.9 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=41.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423585 bytes_read=24398859 bytes_retransmit=9 bytes_invalid=0 send_seq=70194 receive_seq=70194 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31999849 coil_temp=31.4 refs=0 mcu_temp=27.88 supply_voltage=3.013 sysload=0.10 cputime=3383.896 memavail=1408420 print_time=70644.473 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.031
Stats 70640.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=480942 bytes_read=7983756 bytes_retransmit=9 bytes_invalid=0 send_seq=73539 receive_seq=73539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999598 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=419250 bytes_read=1292872 bytes_retransmit=0 bytes_invalid=0 send_seq=69842 receive_seq=69842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998416 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=444823 bytes_read=7712966 bytes_retransmit=9 bytes_invalid=0 send_seq=71452 receive_seq=71452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999429 adj=63999571 Octopus_V1.1_F446: temp=29.9 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=41.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423591 bytes_read=24399215 bytes_retransmit=9 bytes_invalid=0 send_seq=70195 receive_seq=70195 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31999834 coil_temp=31.5 refs=0 mcu_temp=27.90 supply_voltage=3.013 sysload=0.10 cputime=3383.985 memavail=1408420 print_time=70645.473 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.031
Stats 70641.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=481160 bytes_read=7984200 bytes_retransmit=9 bytes_invalid=0 send_seq=73555 receive_seq=73555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999595 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=419256 bytes_read=1292888 bytes_retransmit=0 bytes_invalid=0 send_seq=69843 receive_seq=69843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998469 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=444888 bytes_read=7713125 bytes_retransmit=9 bytes_invalid=0 send_seq=71457 receive_seq=71457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999429 adj=63999566 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=42.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423597 bytes_read=24399571 bytes_retransmit=9 bytes_invalid=0 send_seq=70196 receive_seq=70196 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999830 adj=31999853 coil_temp=31.5 refs=0 mcu_temp=27.95 supply_voltage=3.013 sysload=0.10 cputime=3384.076 memavail=1408420 print_time=70646.475 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.255
Stats 70642.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=481362 bytes_read=7984668 bytes_retransmit=9 bytes_invalid=0 send_seq=73570 receive_seq=73570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999593 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=419262 bytes_read=1292904 bytes_retransmit=0 bytes_invalid=0 send_seq=69844 receive_seq=69844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998514 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=444969 bytes_read=7713317 bytes_retransmit=9 bytes_invalid=0 send_seq=71463 receive_seq=71463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999428 adj=63999582 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=42.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423603 bytes_read=24399927 bytes_retransmit=9 bytes_invalid=0 send_seq=70197 receive_seq=70197 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999828 adj=31999844 coil_temp=31.5 refs=0 mcu_temp=27.98 supply_voltage=3.013 sysload=0.10 cputime=3384.168 memavail=1408420 print_time=70647.476 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.155
Stats 70643.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=481564 bytes_read=7985122 bytes_retransmit=9 bytes_invalid=0 send_seq=73585 receive_seq=73585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999594 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=419268 bytes_read=1292920 bytes_retransmit=0 bytes_invalid=0 send_seq=69845 receive_seq=69845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998521 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=445013 bytes_read=7713481 bytes_retransmit=9 bytes_invalid=0 send_seq=71466 receive_seq=71466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999429 adj=63999578 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=42.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423609 bytes_read=24400283 bytes_retransmit=9 bytes_invalid=0 send_seq=70198 receive_seq=70198 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999827 adj=31999840 coil_temp=31.6 refs=0 mcu_temp=28.01 supply_voltage=3.013 sysload=0.10 cputime=3384.262 memavail=1408420 print_time=70648.476 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.014
Stats 70644.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=481766 bytes_read=7985561 bytes_retransmit=9 bytes_invalid=0 send_seq=73600 receive_seq=73600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999597 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=419274 bytes_read=1292936 bytes_retransmit=0 bytes_invalid=0 send_seq=69846 receive_seq=69846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998524 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=445094 bytes_read=7713645 bytes_retransmit=9 bytes_invalid=0 send_seq=71472 receive_seq=71472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999432 adj=63999582 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=42.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423615 bytes_read=24400639 bytes_retransmit=9 bytes_invalid=0 send_seq=70199 receive_seq=70199 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999825 adj=31999831 coil_temp=31.6 refs=0 mcu_temp=28.05 supply_voltage=3.013 sysload=0.10 cputime=3384.352 memavail=1408420 print_time=70649.477 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.345
Stats 70645.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=481984 bytes_read=7986034 bytes_retransmit=9 bytes_invalid=0 send_seq=73616 receive_seq=73616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999600 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419280 bytes_read=1292965 bytes_retransmit=0 bytes_invalid=0 send_seq=69847 receive_seq=69847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998507 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=445159 bytes_read=7713818 bytes_retransmit=9 bytes_invalid=0 send_seq=71477 receive_seq=71477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999433 adj=63999607 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=42.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423621 bytes_read=24400995 bytes_retransmit=9 bytes_invalid=0 send_seq=70200 receive_seq=70200 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999825 adj=31999820 coil_temp=31.7 refs=0 mcu_temp=28.07 supply_voltage=3.013 sysload=0.10 cputime=3384.445 memavail=1408420 print_time=70650.477 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.137
Stats 70646.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=482186 bytes_read=7986471 bytes_retransmit=9 bytes_invalid=0 send_seq=73631 receive_seq=73631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999598 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419286 bytes_read=1292981 bytes_retransmit=0 bytes_invalid=0 send_seq=69848 receive_seq=69848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998354 adj=49998584 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=445206 bytes_read=7713987 bytes_retransmit=9 bytes_invalid=0 send_seq=71481 receive_seq=71481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999432 adj=63999600 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=42.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423627 bytes_read=24401351 bytes_retransmit=9 bytes_invalid=0 send_seq=70201 receive_seq=70201 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999824 adj=31999823 coil_temp=31.7 refs=0 mcu_temp=28.11 supply_voltage=3.013 sysload=0.10 cputime=3384.539 memavail=1408436 print_time=70651.478 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
Stats 70647.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=482394 bytes_read=7986918 bytes_retransmit=9 bytes_invalid=0 send_seq=73647 receive_seq=73647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999589 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419292 bytes_read=1292997 bytes_retransmit=0 bytes_invalid=0 send_seq=69849 receive_seq=69849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998355 adj=49998573 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445293 bytes_read=7714181 bytes_retransmit=9 bytes_invalid=0 send_seq=71488 receive_seq=71488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999430 adj=63999586 Octopus_V1.1_F446: temp=30.3 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=43.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423633 bytes_read=24401707 bytes_retransmit=9 bytes_invalid=0 send_seq=70202 receive_seq=70202 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999823 adj=31999830 coil_temp=31.7 refs=0 mcu_temp=28.15 supply_voltage=3.013 sysload=0.10 cputime=3384.632 memavail=1408700 print_time=70652.479 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.380
Stats 70648.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=482596 bytes_read=7987399 bytes_retransmit=9 bytes_invalid=0 send_seq=73662 receive_seq=73662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999587 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419298 bytes_read=1293013 bytes_retransmit=0 bytes_invalid=0 send_seq=69850 receive_seq=69850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998353 adj=49998589 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445357 bytes_read=7714354 bytes_retransmit=9 bytes_invalid=0 send_seq=71493 receive_seq=71493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999430 adj=63999607 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=43.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423639 bytes_read=24402063 bytes_retransmit=9 bytes_invalid=0 send_seq=70203 receive_seq=70203 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999822 adj=31999853 coil_temp=31.8 refs=0 mcu_temp=28.21 supply_voltage=3.013 sysload=0.10 cputime=3384.730 memavail=1408700 print_time=70653.479 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.5 pwm=0.044
Stats 70649.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=482814 bytes_read=7987843 bytes_retransmit=9 bytes_invalid=0 send_seq=73678 receive_seq=73678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999580 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419304 bytes_read=1293029 bytes_retransmit=0 bytes_invalid=0 send_seq=69851 receive_seq=69851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998352 adj=49998549 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445391 bytes_read=7714518 bytes_retransmit=9 bytes_invalid=0 send_seq=71496 receive_seq=71496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999427 adj=63999603 Octopus_V1.1_F446: temp=30.3 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=43.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423645 bytes_read=24402419 bytes_retransmit=9 bytes_invalid=0 send_seq=70204 receive_seq=70204 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999820 adj=31999854 coil_temp=31.8 refs=0 mcu_temp=28.25 supply_voltage=3.013 sysload=0.33 cputime=3384.805 memavail=1409700 print_time=70654.480 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.1 pwm=0.044
Stats 70650.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=483016 bytes_read=7988282 bytes_retransmit=9 bytes_invalid=0 send_seq=73693 receive_seq=73693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999573 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=419310 bytes_read=1293058 bytes_retransmit=0 bytes_invalid=0 send_seq=69852 receive_seq=69852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998543 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445471 bytes_read=7714682 bytes_retransmit=9 bytes_invalid=0 send_seq=71502 receive_seq=71502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999428 adj=63999601 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=43.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423651 bytes_read=24402775 bytes_retransmit=9 bytes_invalid=0 send_seq=70205 receive_seq=70205 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999818 adj=31999863 coil_temp=31.8 refs=0 mcu_temp=28.27 supply_voltage=3.013 sysload=0.33 cputime=3384.845 memavail=1409512 print_time=70655.481 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.287
Stats 70651.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=483218 bytes_read=7988750 bytes_retransmit=9 bytes_invalid=0 send_seq=73708 receive_seq=73708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999571 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=419316 bytes_read=1293074 bytes_retransmit=0 bytes_invalid=0 send_seq=69853 receive_seq=69853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998476 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445552 bytes_read=7714860 bytes_retransmit=9 bytes_invalid=0 send_seq=71508 receive_seq=71508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999425 adj=63999636 Octopus_V1.1_F446: temp=30.3 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=43.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423657 bytes_read=24403131 bytes_retransmit=9 bytes_invalid=0 send_seq=70206 receive_seq=70206 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999816 adj=31999850 coil_temp=31.9 refs=0 mcu_temp=28.32 supply_voltage=3.013 sysload=0.33 cputime=3384.885 memavail=1409512 print_time=70656.482 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.184
Stats 70652.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=483420 bytes_read=7989189 bytes_retransmit=9 bytes_invalid=0 send_seq=73723 receive_seq=73723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999564 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=419322 bytes_read=1293090 bytes_retransmit=0 bytes_invalid=0 send_seq=69854 receive_seq=69854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998432 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000010 bytes_write=445599 bytes_read=7715043 bytes_retransmit=9 bytes_invalid=0 send_seq=71512 receive_seq=71512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999423 adj=63999596 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=43.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423663 bytes_read=24403487 bytes_retransmit=9 bytes_invalid=0 send_seq=70207 receive_seq=70207 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999814 adj=31999833 coil_temp=31.9 refs=0 mcu_temp=28.35 supply_voltage=3.013 sysload=0.33 cputime=3384.925 memavail=1409512 print_time=70657.482 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.000
Stats 70653.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=483622 bytes_read=7989643 bytes_retransmit=9 bytes_invalid=0 send_seq=73738 receive_seq=73738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999557 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=419328 bytes_read=1293106 bytes_retransmit=0 bytes_invalid=0 send_seq=69855 receive_seq=69855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998418 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000010 bytes_write=445680 bytes_read=7715207 bytes_retransmit=9 bytes_invalid=0 send_seq=71518 receive_seq=71518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999597 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=44.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423669 bytes_read=24403843 bytes_retransmit=9 bytes_invalid=0 send_seq=70208 receive_seq=70208 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999813 adj=31999847 coil_temp=31.9 refs=0 mcu_temp=28.39 supply_voltage=3.013 sysload=0.33 cputime=3384.965 memavail=1409268 print_time=70658.483 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.2 pwm=0.407
Stats 70654.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=483840 bytes_read=7990116 bytes_retransmit=9 bytes_invalid=0 send_seq=73754 receive_seq=73754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999563 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=419334 bytes_read=1293122 bytes_retransmit=0 bytes_invalid=0 send_seq=69856 receive_seq=69856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998400 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000010 bytes_write=445745 bytes_read=7715380 bytes_retransmit=9 bytes_invalid=0 send_seq=71523 receive_seq=71523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999423 adj=63999609 Octopus_V1.1_F446: temp=30.6 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=44.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423675 bytes_read=24404199 bytes_retransmit=9 bytes_invalid=0 send_seq=70209 receive_seq=70209 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999810 adj=31999848 coil_temp=31.9 refs=0 mcu_temp=28.42 supply_voltage=3.013 sysload=0.30 cputime=3385.029 memavail=1409056 print_time=70659.486 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.168
Stats 70655.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=484042 bytes_read=7990555 bytes_retransmit=9 bytes_invalid=0 send_seq=73769 receive_seq=73769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999567 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=419340 bytes_read=1293151 bytes_retransmit=0 bytes_invalid=0 send_seq=69857 receive_seq=69857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998336 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000010 bytes_write=445792 bytes_read=7715549 bytes_retransmit=9 bytes_invalid=0 send_seq=71527 receive_seq=71527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999585 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=44.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423681 bytes_read=24404555 bytes_retransmit=9 bytes_invalid=0 send_seq=70210 receive_seq=70210 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999810 adj=31999809 coil_temp=31.9 refs=0 mcu_temp=28.48 supply_voltage=3.013 sysload=0.30 cputime=3385.126 memavail=1409064 print_time=70660.484 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
Stats 70656.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=484244 bytes_read=7990994 bytes_retransmit=9 bytes_invalid=0 send_seq=73784 receive_seq=73784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999567 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=419346 bytes_read=1293167 bytes_retransmit=0 bytes_invalid=0 send_seq=69858 receive_seq=69858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998419 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000010 bytes_write=445867 bytes_read=7715708 bytes_retransmit=9 bytes_invalid=0 send_seq=71532 receive_seq=71532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999558 Octopus_V1.1_F446: temp=30.6 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=44.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423687 bytes_read=24404911 bytes_retransmit=9 bytes_invalid=0 send_seq=70211 receive_seq=70211 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999809 adj=31999808 coil_temp=32.0 refs=0 mcu_temp=28.52 supply_voltage=3.014 sysload=0.30 cputime=3385.223 memavail=1409064 print_time=70661.484 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.331
Stats 70657.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=484446 bytes_read=7991462 bytes_retransmit=9 bytes_invalid=0 send_seq=73799 receive_seq=73799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999571 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=419352 bytes_read=1293183 bytes_retransmit=0 bytes_invalid=0 send_seq=69859 receive_seq=69859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998446 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445932 bytes_read=7715895 bytes_retransmit=9 bytes_invalid=0 send_seq=71537 receive_seq=71537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999567 Octopus_V1.1_F446: temp=30.6 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=44.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423693 bytes_read=24405267 bytes_retransmit=9 bytes_invalid=0 send_seq=70212 receive_seq=70212 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999808 adj=31999820 coil_temp=32.0 refs=0 mcu_temp=28.54 supply_voltage=3.014 sysload=0.30 cputime=3385.314 memavail=1409064 print_time=70662.486 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.189
Stats 70658.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=484664 bytes_read=7991921 bytes_retransmit=9 bytes_invalid=0 send_seq=73815 receive_seq=73815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999574 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=419364 bytes_read=1293215 bytes_retransmit=0 bytes_invalid=0 send_seq=69861 receive_seq=69861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998466 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=445981 bytes_read=7716058 bytes_retransmit=9 bytes_invalid=0 send_seq=71541 receive_seq=71541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999532 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=44.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423699 bytes_read=24405623 bytes_retransmit=9 bytes_invalid=0 send_seq=70213 receive_seq=70213 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999806 adj=31999804 coil_temp=32.0 refs=0 mcu_temp=28.58 supply_voltage=3.013 sysload=0.30 cputime=3385.408 memavail=1409064 print_time=70663.487 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.020
Stats 70659.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=484866 bytes_read=7992360 bytes_retransmit=9 bytes_invalid=0 send_seq=73830 receive_seq=73830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999572 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=419370 bytes_read=1293231 bytes_retransmit=0 bytes_invalid=0 send_seq=69862 receive_seq=69862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998479 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=446061 bytes_read=7716215 bytes_retransmit=9 bytes_invalid=0 send_seq=71547 receive_seq=71547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999529 Octopus_V1.1_F446: temp=30.5 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=45.1 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423705 bytes_read=24405979 bytes_retransmit=9 bytes_invalid=0 send_seq=70214 receive_seq=70214 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999806 adj=31999793 coil_temp=32.1 refs=0 mcu_temp=28.62 supply_voltage=3.013 sysload=0.36 cputime=3385.503 memavail=1409064 print_time=70664.487 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.5 pwm=0.359
Stats 70660.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=485068 bytes_read=7992828 bytes_retransmit=9 bytes_invalid=0 send_seq=73845 receive_seq=73845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999567 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=419376 bytes_read=1293260 bytes_retransmit=0 bytes_invalid=0 send_seq=69863 receive_seq=69863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998485 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=446126 bytes_read=7716380 bytes_retransmit=9 bytes_invalid=0 send_seq=71552 receive_seq=71552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999551 Octopus_V1.1_F446: temp=30.6 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=45.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423711 bytes_read=24406335 bytes_retransmit=9 bytes_invalid=0 send_seq=70215 receive_seq=70215 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999805 adj=31999813 coil_temp=32.1 refs=0 mcu_temp=28.66 supply_voltage=3.013 sysload=0.36 cputime=3385.598 memavail=1409064 print_time=70665.488 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.129
Stats 70661.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=485270 bytes_read=7993267 bytes_retransmit=9 bytes_invalid=0 send_seq=73860 receive_seq=73860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999567 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=419382 bytes_read=1293276 bytes_retransmit=0 bytes_invalid=0 send_seq=69864 receive_seq=69864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998490 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=446173 bytes_read=7716541 bytes_retransmit=9 bytes_invalid=0 send_seq=71556 receive_seq=71556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999575 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=45.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423717 bytes_read=24406691 bytes_retransmit=9 bytes_invalid=0 send_seq=70216 receive_seq=70216 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999805 adj=31999836 coil_temp=32.1 refs=0 mcu_temp=28.70 supply_voltage=3.013 sysload=0.36 cputime=3385.692 memavail=1408816 print_time=70666.488 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.000
Stats 70662.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=485488 bytes_read=7993711 bytes_retransmit=9 bytes_invalid=0 send_seq=73876 receive_seq=73876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999563 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=419388 bytes_read=1293292 bytes_retransmit=0 bytes_invalid=0 send_seq=69865 receive_seq=69865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998476 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446254 bytes_read=7716715 bytes_retransmit=9 bytes_invalid=0 send_seq=71562 receive_seq=71562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999575 Octopus_V1.1_F446: temp=30.9 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=45.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423723 bytes_read=24407047 bytes_retransmit=9 bytes_invalid=0 send_seq=70217 receive_seq=70217 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999804 adj=31999845 coil_temp=32.1 refs=0 mcu_temp=28.75 supply_voltage=3.013 sysload=0.36 cputime=3385.788 memavail=1408816 print_time=70667.489 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.3 pwm=0.403
Stats 70663.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=485690 bytes_read=7994194 bytes_retransmit=9 bytes_invalid=0 send_seq=73891 receive_seq=73891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999559 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=419394 bytes_read=1293308 bytes_retransmit=0 bytes_invalid=0 send_seq=69866 receive_seq=69866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998343 adj=49998476 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446314 bytes_read=7716883 bytes_retransmit=9 bytes_invalid=0 send_seq=71566 receive_seq=71566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999605 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=45.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423729 bytes_read=24407403 bytes_retransmit=9 bytes_invalid=0 send_seq=70218 receive_seq=70218 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999803 adj=31999852 coil_temp=32.2 refs=0 mcu_temp=28.79 supply_voltage=3.013 sysload=0.36 cputime=3385.884 memavail=1408816 print_time=70668.490 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.168
Stats 70664.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=485892 bytes_read=7994633 bytes_retransmit=9 bytes_invalid=0 send_seq=73906 receive_seq=73906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999555 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=419400 bytes_read=1293324 bytes_retransmit=0 bytes_invalid=0 send_seq=69867 receive_seq=69867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998521 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446363 bytes_read=7717052 bytes_retransmit=9 bytes_invalid=0 send_seq=71570 receive_seq=71570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999629 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=45.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423741 bytes_read=24407775 bytes_retransmit=9 bytes_invalid=0 send_seq=70220 receive_seq=70220 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999801 adj=31999851 coil_temp=32.2 refs=0 mcu_temp=28.83 supply_voltage=3.013 sysload=0.41 cputime=3385.978 memavail=1410744 print_time=70669.490 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.008
Stats 70665.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=486094 bytes_read=7995072 bytes_retransmit=9 bytes_invalid=0 send_seq=73921 receive_seq=73921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999553 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419406 bytes_read=1293353 bytes_retransmit=0 bytes_invalid=0 send_seq=69868 receive_seq=69868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998348 adj=49998574 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446428 bytes_read=7717211 bytes_retransmit=9 bytes_invalid=0 send_seq=71575 receive_seq=71575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999623 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=46.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423747 bytes_read=24408131 bytes_retransmit=9 bytes_invalid=0 send_seq=70221 receive_seq=70221 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999800 adj=31999833 coil_temp=32.2 refs=0 mcu_temp=28.88 supply_voltage=3.013 sysload=0.41 cputime=3386.074 memavail=1410744 print_time=70670.490 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.325
Stats 70666.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=486307 bytes_read=7995540 bytes_retransmit=9 bytes_invalid=0 send_seq=73936 receive_seq=73936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999552 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419412 bytes_read=1293369 bytes_retransmit=0 bytes_invalid=0 send_seq=69869 receive_seq=69869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998589 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446509 bytes_read=7717389 bytes_retransmit=9 bytes_invalid=0 send_seq=71581 receive_seq=71581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999425 adj=63999624 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=46.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423753 bytes_read=24408487 bytes_retransmit=9 bytes_invalid=0 send_seq=70222 receive_seq=70222 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999799 adj=31999838 coil_temp=32.3 refs=0 mcu_temp=28.92 supply_voltage=3.013 sysload=0.41 cputime=3386.169 memavail=1404444 print_time=70671.491 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.229
Stats 70667.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=486509 bytes_read=7995979 bytes_retransmit=9 bytes_invalid=0 send_seq=73951 receive_seq=73951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999550 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419418 bytes_read=1293385 bytes_retransmit=0 bytes_invalid=0 send_seq=69870 receive_seq=69870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998532 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446571 bytes_read=7717577 bytes_retransmit=9 bytes_invalid=0 send_seq=71586 receive_seq=71586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999423 adj=63999679 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=46.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423759 bytes_read=24408827 bytes_retransmit=9 bytes_invalid=0 send_seq=70223 receive_seq=70223 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999797 adj=31999833 coil_temp=32.3 refs=0 mcu_temp=28.96 supply_voltage=3.013 sysload=0.41 cputime=3386.209 memavail=1409760 print_time=70672.492 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.6 pwm=0.000
Stats 70668.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=486711 bytes_read=7996433 bytes_retransmit=9 bytes_invalid=0 send_seq=73966 receive_seq=73966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999541 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419424 bytes_read=1293401 bytes_retransmit=0 bytes_invalid=0 send_seq=69871 receive_seq=69871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998485 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446636 bytes_read=7717736 bytes_retransmit=9 bytes_invalid=0 send_seq=71591 receive_seq=71591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999634 Octopus_V1.1_F446: temp=30.9 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=46.5 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423765 bytes_read=24409183 bytes_retransmit=9 bytes_invalid=0 send_seq=70224 receive_seq=70224 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999794 adj=31999820 coil_temp=32.3 refs=0 mcu_temp=28.99 supply_voltage=3.013 sysload=0.41 cputime=3386.249 memavail=1409760 print_time=70673.493 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.323
Stats 70669.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=486913 bytes_read=7996901 bytes_retransmit=9 bytes_invalid=0 send_seq=73981 receive_seq=73981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999532 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419430 bytes_read=1293417 bytes_retransmit=0 bytes_invalid=0 send_seq=69872 receive_seq=69872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998481 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446685 bytes_read=7717904 bytes_retransmit=9 bytes_invalid=0 send_seq=71595 receive_seq=71595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999418 adj=63999637 Octopus_V1.1_F446: temp=31.1 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=46.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423771 bytes_read=24409539 bytes_retransmit=9 bytes_invalid=0 send_seq=70225 receive_seq=70225 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999793 adj=31999825 coil_temp=32.4 refs=0 mcu_temp=29.03 supply_voltage=3.013 sysload=0.38 cputime=3386.288 memavail=1409760 print_time=70674.493 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.206
Stats 70670.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=487131 bytes_read=7997341 bytes_retransmit=9 bytes_invalid=0 send_seq=73997 receive_seq=73997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999523 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000017 bytes_write=419436 bytes_read=1293446 bytes_retransmit=0 bytes_invalid=0 send_seq=69873 receive_seq=69873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998456 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446747 bytes_read=7718078 bytes_retransmit=9 bytes_invalid=0 send_seq=71600 receive_seq=71600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999420 adj=63999636 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=46.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423777 bytes_read=24409895 bytes_retransmit=9 bytes_invalid=0 send_seq=70226 receive_seq=70226 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999791 adj=31999835 coil_temp=32.4 refs=0 mcu_temp=29.08 supply_voltage=3.013 sysload=0.38 cputime=3386.328 memavail=1409264 print_time=70675.493 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.1 pwm=0.000
Stats 70671.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=487333 bytes_read=7997773 bytes_retransmit=9 bytes_invalid=0 send_seq=74012 receive_seq=74012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999516 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000017 bytes_write=419442 bytes_read=1293462 bytes_retransmit=0 bytes_invalid=0 send_seq=69874 receive_seq=69874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998443 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446827 bytes_read=7718256 bytes_retransmit=9 bytes_invalid=0 send_seq=71606 receive_seq=71606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999418 adj=63999704 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=46.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423783 bytes_read=24410251 bytes_retransmit=9 bytes_invalid=0 send_seq=70227 receive_seq=70227 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999790 adj=31999840 coil_temp=32.4 refs=0 mcu_temp=29.11 supply_voltage=3.013 sysload=0.38 cputime=3386.376 memavail=1409264 print_time=70676.494 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.346
Stats 70672.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=487535 bytes_read=7998241 bytes_retransmit=9 bytes_invalid=0 send_seq=74027 receive_seq=74027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999523 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000017 bytes_write=419448 bytes_read=1293478 bytes_retransmit=0 bytes_invalid=0 send_seq=69875 receive_seq=69875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998422 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446876 bytes_read=7718424 bytes_retransmit=9 bytes_invalid=0 send_seq=71610 receive_seq=71610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999680 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=47.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423789 bytes_read=24410607 bytes_retransmit=9 bytes_invalid=0 send_seq=70228 receive_seq=70228 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999790 adj=31999855 coil_temp=32.4 refs=0 mcu_temp=29.14 supply_voltage=3.013 sysload=0.38 cputime=3386.473 memavail=1409264 print_time=70677.494 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.210
Stats 70673.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=487737 bytes_read=7998695 bytes_retransmit=9 bytes_invalid=0 send_seq=74042 receive_seq=74042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999522 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000017 bytes_write=419454 bytes_read=1293494 bytes_retransmit=0 bytes_invalid=0 send_seq=69876 receive_seq=69876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998418 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446925 bytes_read=7718593 bytes_retransmit=9 bytes_invalid=0 send_seq=71614 receive_seq=71614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999639 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=47.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423795 bytes_read=24410963 bytes_retransmit=9 bytes_invalid=0 send_seq=70229 receive_seq=70229 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999790 adj=31999848 coil_temp=32.5 refs=0 mcu_temp=29.18 supply_voltage=3.013 sysload=0.38 cputime=3386.569 memavail=1409264 print_time=70678.494 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.029
Stats 70674.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=487939 bytes_read=7999134 bytes_retransmit=9 bytes_invalid=0 send_seq=74057 receive_seq=74057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999522 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000017 bytes_write=419460 bytes_read=1293510 bytes_retransmit=0 bytes_invalid=0 send_seq=69877 receive_seq=69877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998442 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=446985 bytes_read=7718747 bytes_retransmit=9 bytes_invalid=0 send_seq=71618 receive_seq=71618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999424 adj=63999621 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=47.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423801 bytes_read=24411319 bytes_retransmit=9 bytes_invalid=0 send_seq=70230 receive_seq=70230 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999791 adj=31999853 coil_temp=32.5 refs=0 mcu_temp=29.21 supply_voltage=3.013 sysload=0.35 cputime=3386.665 memavail=1408508 print_time=70679.494 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.258
Stats 70675.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=488157 bytes_read=7999607 bytes_retransmit=9 bytes_invalid=0 send_seq=74073 receive_seq=74073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999521 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419466 bytes_read=1293539 bytes_retransmit=0 bytes_invalid=0 send_seq=69878 receive_seq=69878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998483 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447035 bytes_read=7718915 bytes_retransmit=9 bytes_invalid=0 send_seq=71622 receive_seq=71622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999424 adj=63999700 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=47.4 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423807 bytes_read=24411675 bytes_retransmit=9 bytes_invalid=0 send_seq=70231 receive_seq=70231 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999791 adj=31999871 coil_temp=32.6 refs=0 mcu_temp=29.26 supply_voltage=3.013 sysload=0.35 cputime=3386.760 memavail=1408508 print_time=70680.495 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.321
Stats 70676.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=488359 bytes_read=8000046 bytes_retransmit=9 bytes_invalid=0 send_seq=74088 receive_seq=74088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999522 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419472 bytes_read=1293555 bytes_retransmit=0 bytes_invalid=0 send_seq=69879 receive_seq=69879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998479 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447097 bytes_read=7719089 bytes_retransmit=9 bytes_invalid=0 send_seq=71627 receive_seq=71627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999424 adj=63999668 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=47.6 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423813 bytes_read=24412031 bytes_retransmit=9 bytes_invalid=0 send_seq=70232 receive_seq=70232 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999790 adj=31999871 coil_temp=32.6 refs=0 mcu_temp=29.29 supply_voltage=3.013 sysload=0.35 cputime=3386.856 memavail=1408284 print_time=70681.495 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.000
Stats 70677.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=488561 bytes_read=8000485 bytes_retransmit=9 bytes_invalid=0 send_seq=74103 receive_seq=74103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999519 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419478 bytes_read=1293571 bytes_retransmit=0 bytes_invalid=0 send_seq=69880 receive_seq=69880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998490 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447162 bytes_read=7719262 bytes_retransmit=9 bytes_invalid=0 send_seq=71632 receive_seq=71632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999423 adj=63999646 Octopus_V1.1_F446: temp=31.1 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=47.7 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423819 bytes_read=24412387 bytes_retransmit=9 bytes_invalid=0 send_seq=70233 receive_seq=70233 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999791 adj=31999853 coil_temp=32.7 refs=0 mcu_temp=29.35 supply_voltage=3.013 sysload=0.35 cputime=3386.947 memavail=1408284 print_time=70682.495 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.5 pwm=0.361
Stats 70678.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=488763 bytes_read=8000968 bytes_retransmit=9 bytes_invalid=0 send_seq=74118 receive_seq=74118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999515 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419484 bytes_read=1293587 bytes_retransmit=0 bytes_invalid=0 send_seq=69881 receive_seq=69881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998505 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447228 bytes_read=7719435 bytes_retransmit=9 bytes_invalid=0 send_seq=71637 receive_seq=71637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999428 adj=63999637 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=47.8 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423825 bytes_read=24412743 bytes_retransmit=9 bytes_invalid=0 send_seq=70234 receive_seq=70234 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999792 adj=31999897 coil_temp=32.7 refs=0 mcu_temp=29.38 supply_voltage=3.013 sysload=0.35 cputime=3387.040 memavail=1408284 print_time=70683.496 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.251
Stats 70679.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=488981 bytes_read=8001412 bytes_retransmit=9 bytes_invalid=0 send_seq=74134 receive_seq=74134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999513 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419490 bytes_read=1293603 bytes_retransmit=0 bytes_invalid=0 send_seq=69882 receive_seq=69882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998335 adj=49998509 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447277 bytes_read=7719604 bytes_retransmit=9 bytes_invalid=0 send_seq=71641 receive_seq=71641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999432 adj=63999733 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=47.9 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423831 bytes_read=24413099 bytes_retransmit=9 bytes_invalid=0 send_seq=70235 receive_seq=70235 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999790 adj=31999911 coil_temp=32.7 refs=0 mcu_temp=29.42 supply_voltage=3.013 sysload=0.32 cputime=3387.133 memavail=1408284 print_time=70684.497 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.5 pwm=0.041
Stats 70680.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=489183 bytes_read=8001851 bytes_retransmit=9 bytes_invalid=0 send_seq=74149 receive_seq=74149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999523 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=419496 bytes_read=1293619 bytes_retransmit=0 bytes_invalid=0 send_seq=69883 receive_seq=69883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998512 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447326 bytes_read=7719758 bytes_retransmit=9 bytes_invalid=0 send_seq=71645 receive_seq=71645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999433 adj=63999776 Octopus_V1.1_F446: temp=31.4 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=48.1 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423837 bytes_read=24413455 bytes_retransmit=9 bytes_invalid=0 send_seq=70236 receive_seq=70236 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999789 adj=31999883 coil_temp=32.7 refs=0 mcu_temp=29.46 supply_voltage=3.013 sysload=0.32 cputime=3387.224 memavail=1408284 print_time=70685.497 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.4 pwm=0.150
Stats 70681.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=489385 bytes_read=8002319 bytes_retransmit=9 bytes_invalid=0 send_seq=74164 receive_seq=74164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999519 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419502 bytes_read=1293648 bytes_retransmit=0 bytes_invalid=0 send_seq=69884 receive_seq=69884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998445 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447376 bytes_read=7719926 bytes_retransmit=9 bytes_invalid=0 send_seq=71649 receive_seq=71649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999432 adj=63999682 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=48.2 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423843 bytes_read=24413811 bytes_retransmit=9 bytes_invalid=0 send_seq=70237 receive_seq=70237 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999788 adj=31999840 coil_temp=32.8 refs=0 mcu_temp=29.50 supply_voltage=3.013 sysload=0.32 cputime=3387.317 memavail=1408552 print_time=70686.497 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.5 pwm=0.341
Stats 70682.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=489587 bytes_read=8002758 bytes_retransmit=9 bytes_invalid=0 send_seq=74179 receive_seq=74179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999515 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419508 bytes_read=1293664 bytes_retransmit=0 bytes_invalid=0 send_seq=69885 receive_seq=69885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998500 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447453 bytes_read=7720119 bytes_retransmit=9 bytes_invalid=0 send_seq=71655 receive_seq=71655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999430 adj=63999681 Octopus_V1.1_F446: temp=31.4 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=48.3 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423849 bytes_read=24414167 bytes_retransmit=9 bytes_invalid=0 send_seq=70238 receive_seq=70238 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999787 adj=31999839 coil_temp=32.8 refs=0 mcu_temp=29.54 supply_voltage=3.013 sysload=0.32 cputime=3387.409 memavail=1408548 print_time=70687.497 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.5 pwm=0.000
Stats 70683.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=489805 bytes_read=8003217 bytes_retransmit=9 bytes_invalid=0 send_seq=74195 receive_seq=74195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999513 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419514 bytes_read=1293680 bytes_retransmit=0 bytes_invalid=0 send_seq=69886 receive_seq=69886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998596 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447502 bytes_read=7720273 bytes_retransmit=9 bytes_invalid=0 send_seq=71659 receive_seq=71659 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999429 adj=63999649 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=48.5 pwm=0.992 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423855 bytes_read=24414523 bytes_retransmit=9 bytes_invalid=0 send_seq=70239 receive_seq=70239 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999786 adj=31999838 coil_temp=32.9 refs=0 mcu_temp=29.58 supply_voltage=3.013 sysload=0.32 cputime=3387.502 memavail=1407292 print_time=70688.498 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.4 pwm=0.177
Stats 70684.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=490007 bytes_read=8003685 bytes_retransmit=9 bytes_invalid=0 send_seq=74210 receive_seq=74210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999506 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419520 bytes_read=1293696 bytes_retransmit=0 bytes_invalid=0 send_seq=69887 receive_seq=69887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998648 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447568 bytes_read=7720446 bytes_retransmit=9 bytes_invalid=0 send_seq=71664 receive_seq=71664 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999426 adj=63999627 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=48.7 pwm=0.992 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423861 bytes_read=24414879 bytes_retransmit=9 bytes_invalid=0 send_seq=70240 receive_seq=70240 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999784 adj=31999834 coil_temp=32.9 refs=0 mcu_temp=29.64 supply_voltage=3.013 sysload=0.29 cputime=3387.549 memavail=1410984 print_time=70689.498 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.390
Stats 70685.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=490209 bytes_read=8004124 bytes_retransmit=9 bytes_invalid=0 send_seq=74225 receive_seq=74225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999499 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419526 bytes_read=1293712 bytes_retransmit=0 bytes_invalid=0 send_seq=69888 receive_seq=69888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998600 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447633 bytes_read=7720620 bytes_retransmit=9 bytes_invalid=0 send_seq=71669 receive_seq=71669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999616 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=48.8 pwm=0.992 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423867 bytes_read=24415235 bytes_retransmit=9 bytes_invalid=0 send_seq=70241 receive_seq=70241 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999781 adj=31999832 coil_temp=33.0 refs=0 mcu_temp=29.69 supply_voltage=3.013 sysload=0.29 cputime=3387.589 memavail=1410984 print_time=70690.498 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.5 pwm=0.047
Stats 70686.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=490411 bytes_read=8004563 bytes_retransmit=9 bytes_invalid=0 send_seq=74240 receive_seq=74240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999505 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419532 bytes_read=1293741 bytes_retransmit=0 bytes_invalid=0 send_seq=69889 receive_seq=69889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998535 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447667 bytes_read=7720769 bytes_retransmit=9 bytes_invalid=0 send_seq=71672 receive_seq=71672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999593 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=48.9 pwm=0.992 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423873 bytes_read=24415591 bytes_retransmit=9 bytes_invalid=0 send_seq=70242 receive_seq=70242 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999779 adj=31999828 coil_temp=33.0 refs=0 mcu_temp=29.73 supply_voltage=3.013 sysload=0.29 cputime=3387.628 memavail=1410984 print_time=70691.498 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.8 pwm=0.047
Stats 70687.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=490629 bytes_read=8005036 bytes_retransmit=9 bytes_invalid=0 send_seq=74256 receive_seq=74256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999500 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419538 bytes_read=1293757 bytes_retransmit=0 bytes_invalid=0 send_seq=69890 receive_seq=69890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998436 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447717 bytes_read=7720951 bytes_retransmit=9 bytes_invalid=0 send_seq=71676 receive_seq=71676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999416 adj=63999513 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=49.1 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423879 bytes_read=24415947 bytes_retransmit=9 bytes_invalid=0 send_seq=70243 receive_seq=70243 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999777 adj=31999790 coil_temp=33.0 refs=0 mcu_temp=29.77 supply_voltage=3.013 sysload=0.29 cputime=3387.669 memavail=1410484 print_time=70692.498 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.272
Stats 70688.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=490831 bytes_read=8005490 bytes_retransmit=9 bytes_invalid=0 send_seq=74271 receive_seq=74271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999494 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419544 bytes_read=1293773 bytes_retransmit=0 bytes_invalid=0 send_seq=69891 receive_seq=69891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998329 adj=49998411 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447776 bytes_read=7721120 bytes_retransmit=9 bytes_invalid=0 send_seq=71680 receive_seq=71680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999511 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=49.2 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423885 bytes_read=24416303 bytes_retransmit=9 bytes_invalid=0 send_seq=70244 receive_seq=70244 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999775 adj=31999789 coil_temp=33.0 refs=0 mcu_temp=29.81 supply_voltage=3.013 sysload=0.29 cputime=3387.710 memavail=1410484 print_time=70693.499 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.2 pwm=0.046
Stats 70689.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=491033 bytes_read=8005929 bytes_retransmit=9 bytes_invalid=0 send_seq=74286 receive_seq=74286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999499 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419550 bytes_read=1293789 bytes_retransmit=0 bytes_invalid=0 send_seq=69892 receive_seq=69892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998400 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447825 bytes_read=7721274 bytes_retransmit=9 bytes_invalid=0 send_seq=71684 receive_seq=71684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999415 adj=63999530 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=49.4 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423891 bytes_read=24416659 bytes_retransmit=9 bytes_invalid=0 send_seq=70245 receive_seq=70245 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999774 adj=31999791 coil_temp=33.1 refs=0 mcu_temp=29.85 supply_voltage=3.013 sysload=0.27 cputime=3387.797 memavail=1410484 print_time=70694.499 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.5 pwm=0.131
Stats 70690.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=491235 bytes_read=8006397 bytes_retransmit=9 bytes_invalid=0 send_seq=74301 receive_seq=74301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999504 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=419556 bytes_read=1293805 bytes_retransmit=0 bytes_invalid=0 send_seq=69893 receive_seq=69893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998405 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447890 bytes_read=7721447 bytes_retransmit=9 bytes_invalid=0 send_seq=71689 receive_seq=71689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999415 adj=63999545 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=49.6 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423897 bytes_read=24417015 bytes_retransmit=9 bytes_invalid=0 send_seq=70246 receive_seq=70246 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999773 adj=31999782 coil_temp=33.1 refs=0 mcu_temp=29.88 supply_voltage=3.013 sysload=0.27 cputime=3387.893 memavail=1410484 print_time=70695.499 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.5 pwm=0.343
Stats 70691.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=491453 bytes_read=8006841 bytes_retransmit=9 bytes_invalid=0 send_seq=74317 receive_seq=74317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999504 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=419562 bytes_read=1293834 bytes_retransmit=0 bytes_invalid=0 send_seq=69894 receive_seq=69894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998431 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=447968 bytes_read=7721626 bytes_retransmit=9 bytes_invalid=0 send_seq=71695 receive_seq=71695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999520 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=49.7 pwm=0.986 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423903 bytes_read=24417371 bytes_retransmit=9 bytes_invalid=0 send_seq=70247 receive_seq=70247 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999773 adj=31999778 coil_temp=33.2 refs=0 mcu_temp=29.94 supply_voltage=3.013 sysload=0.27 cputime=3387.990 memavail=1410232 print_time=70696.501 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.000
Stats 70692.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=491655 bytes_read=8007280 bytes_retransmit=9 bytes_invalid=0 send_seq=74332 receive_seq=74332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999504 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=419568 bytes_read=1293850 bytes_retransmit=0 bytes_invalid=0 send_seq=69895 receive_seq=69895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998453 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448017 bytes_read=7721794 bytes_retransmit=9 bytes_invalid=0 send_seq=71699 receive_seq=71699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999415 adj=63999528 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=49.7 pwm=0.986 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423909 bytes_read=24417727 bytes_retransmit=9 bytes_invalid=0 send_seq=70248 receive_seq=70248 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999772 adj=31999786 coil_temp=33.2 refs=0 mcu_temp=29.98 supply_voltage=3.013 sysload=0.27 cputime=3388.084 memavail=1410232 print_time=70697.501 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.073
Stats 70693.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=491857 bytes_read=8007763 bytes_retransmit=9 bytes_invalid=0 send_seq=74347 receive_seq=74347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999502 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=419574 bytes_read=1293866 bytes_retransmit=0 bytes_invalid=0 send_seq=69896 receive_seq=69896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998467 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448099 bytes_read=7721972 bytes_retransmit=9 bytes_invalid=0 send_seq=71705 receive_seq=71705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999550 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=49.9 pwm=0.986 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423915 bytes_read=24418083 bytes_retransmit=9 bytes_invalid=0 send_seq=70249 receive_seq=70249 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999771 adj=31999793 coil_temp=33.3 refs=0 mcu_temp=30.00 supply_voltage=3.013 sysload=0.27 cputime=3388.183 memavail=1410232 print_time=70698.502 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.2 pwm=0.403
Stats 70694.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=492059 bytes_read=8008198 bytes_retransmit=9 bytes_invalid=0 send_seq=74362 receive_seq=74362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999514 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=419580 bytes_read=1293882 bytes_retransmit=0 bytes_invalid=0 send_seq=69897 receive_seq=69897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998488 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448177 bytes_read=7722151 bytes_retransmit=9 bytes_invalid=0 send_seq=71711 receive_seq=71711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999417 adj=63999559 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=50.1 pwm=0.986 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423921 bytes_read=24418439 bytes_retransmit=9 bytes_invalid=0 send_seq=70250 receive_seq=70250 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999769 adj=31999796 coil_temp=33.3 refs=0 mcu_temp=30.04 supply_voltage=3.013 sysload=0.25 cputime=3388.279 memavail=1410648 print_time=70699.502 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.000
Stats 70695.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=492261 bytes_read=8008630 bytes_retransmit=9 bytes_invalid=0 send_seq=74377 receive_seq=74377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999514 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=419586 bytes_read=1293898 bytes_retransmit=0 bytes_invalid=0 send_seq=69898 receive_seq=69898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998433 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448226 bytes_read=7722305 bytes_retransmit=9 bytes_invalid=0 send_seq=71715 receive_seq=71715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999416 adj=63999544 Octopus_V1.1_F446: temp=31.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=50.2 pwm=0.986 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423927 bytes_read=24418795 bytes_retransmit=9 bytes_invalid=0 send_seq=70251 receive_seq=70251 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999771 adj=31999761 coil_temp=33.3 refs=0 mcu_temp=30.08 supply_voltage=3.014 sysload=0.25 cputime=3388.375 memavail=1410780 print_time=70700.503 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.105
Heater heater_bed within range of 55.000
Stats 70696.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=492479 bytes_read=8009103 bytes_retransmit=9 bytes_invalid=0 send_seq=74393 receive_seq=74393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999512 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419592 bytes_read=1293927 bytes_retransmit=0 bytes_invalid=0 send_seq=69899 receive_seq=69899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998436 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448276 bytes_read=7722473 bytes_retransmit=9 bytes_invalid=0 send_seq=71719 receive_seq=71719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999415 adj=63999538 Octopus_V1.1_F446: temp=31.9 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=50.4 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423933 bytes_read=24419151 bytes_retransmit=9 bytes_invalid=0 send_seq=70252 receive_seq=70252 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999770 adj=31999804 coil_temp=33.4 refs=0 mcu_temp=30.12 supply_voltage=3.014 sysload=0.25 cputime=3388.474 memavail=1410780 print_time=70701.503 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.327
Stats 70697.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=492681 bytes_read=8009542 bytes_retransmit=9 bytes_invalid=0 send_seq=74408 receive_seq=74408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999510 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419598 bytes_read=1293943 bytes_retransmit=0 bytes_invalid=0 send_seq=69900 receive_seq=69900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998501 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448349 bytes_read=7722661 bytes_retransmit=9 bytes_invalid=0 send_seq=71724 receive_seq=71724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999553 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=50.5 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423939 bytes_read=24419507 bytes_retransmit=9 bytes_invalid=0 send_seq=70253 receive_seq=70253 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999768 adj=31999807 coil_temp=33.4 refs=0 mcu_temp=30.16 supply_voltage=3.014 sysload=0.25 cputime=3388.571 memavail=1410784 print_time=70702.503 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70698.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=492883 bytes_read=8009996 bytes_retransmit=9 bytes_invalid=0 send_seq=74423 receive_seq=74423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999506 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419604 bytes_read=1293959 bytes_retransmit=0 bytes_invalid=0 send_seq=69901 receive_seq=69901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998547 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448413 bytes_read=7722820 bytes_retransmit=9 bytes_invalid=0 send_seq=71729 receive_seq=71729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999421 adj=63999683 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=50.6 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423945 bytes_read=24419863 bytes_retransmit=9 bytes_invalid=0 send_seq=70254 receive_seq=70254 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999766 adj=31999797 coil_temp=33.5 refs=0 mcu_temp=30.21 supply_voltage=3.014 sysload=0.25 cputime=3388.663 memavail=1409776 print_time=70703.503 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.3 pwm=0.205
Stats 70699.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=493085 bytes_read=8010464 bytes_retransmit=9 bytes_invalid=0 send_seq=74438 receive_seq=74438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999500 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419610 bytes_read=1293975 bytes_retransmit=0 bytes_invalid=0 send_seq=69902 receive_seq=69902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998587 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448458 bytes_read=7722983 bytes_retransmit=9 bytes_invalid=0 send_seq=71732 receive_seq=71732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999668 Octopus_V1.1_F446: temp=31.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=50.8 pwm=0.997 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423951 bytes_read=24420219 bytes_retransmit=9 bytes_invalid=0 send_seq=70255 receive_seq=70255 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999765 adj=31999801 coil_temp=33.5 refs=0 mcu_temp=30.25 supply_voltage=3.014 sysload=0.23 cputime=3388.755 memavail=1409552 print_time=70704.503 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.323
Stats 70700.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=493303 bytes_read=8010908 bytes_retransmit=9 bytes_invalid=0 send_seq=74454 receive_seq=74454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999499 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=419616 bytes_read=1293991 bytes_retransmit=0 bytes_invalid=0 send_seq=69903 receive_seq=69903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49998635 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448517 bytes_read=7723152 bytes_retransmit=9 bytes_invalid=0 send_seq=71736 receive_seq=71736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999696 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=50.9 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423957 bytes_read=24420575 bytes_retransmit=9 bytes_invalid=0 send_seq=70256 receive_seq=70256 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999763 adj=31999808 coil_temp=33.5 refs=0 mcu_temp=30.29 supply_voltage=3.014 sysload=0.23 cputime=3388.848 memavail=1409552 print_time=70705.504 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.010
Stats 70701.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=493505 bytes_read=8011347 bytes_retransmit=9 bytes_invalid=0 send_seq=74469 receive_seq=74469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999500 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419622 bytes_read=1294020 bytes_retransmit=0 bytes_invalid=0 send_seq=69904 receive_seq=69904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998625 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=448581 bytes_read=7723311 bytes_retransmit=9 bytes_invalid=0 send_seq=71741 receive_seq=71741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999644 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=51.0 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423963 bytes_read=24420931 bytes_retransmit=9 bytes_invalid=0 send_seq=70257 receive_seq=70257 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999761 adj=31999798 coil_temp=33.6 refs=0 mcu_temp=30.33 supply_voltage=3.014 sysload=0.23 cputime=3388.905 memavail=1409820 print_time=70706.504 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.218
Stats 70702.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=493707 bytes_read=8011815 bytes_retransmit=9 bytes_invalid=0 send_seq=74484 receive_seq=74484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999503 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419628 bytes_read=1294036 bytes_retransmit=0 bytes_invalid=0 send_seq=69905 receive_seq=69905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998555 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448663 bytes_read=7723503 bytes_retransmit=9 bytes_invalid=0 send_seq=71747 receive_seq=71747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999416 adj=63999615 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=51.2 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423969 bytes_read=24421287 bytes_retransmit=9 bytes_invalid=0 send_seq=70258 receive_seq=70258 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999761 adj=31999778 coil_temp=33.6 refs=0 mcu_temp=30.37 supply_voltage=3.014 sysload=0.23 cputime=3388.946 memavail=1409596 print_time=70707.504 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.303
Stats 70703.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=493909 bytes_read=8012269 bytes_retransmit=9 bytes_invalid=0 send_seq=74499 receive_seq=74499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999493 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419634 bytes_read=1294052 bytes_retransmit=0 bytes_invalid=0 send_seq=69906 receive_seq=69906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998470 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448720 bytes_read=7723672 bytes_retransmit=9 bytes_invalid=0 send_seq=71751 receive_seq=71751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999549 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=51.3 pwm=1.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423975 bytes_read=24421643 bytes_retransmit=9 bytes_invalid=0 send_seq=70259 receive_seq=70259 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999758 adj=31999775 coil_temp=33.6 refs=0 mcu_temp=30.41 supply_voltage=3.014 sysload=0.23 cputime=3388.986 memavail=1409596 print_time=70708.504 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.6 pwm=0.000
Stats 70704.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=494127 bytes_read=8012713 bytes_retransmit=9 bytes_invalid=0 send_seq=74515 receive_seq=74515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999485 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419640 bytes_read=1294068 bytes_retransmit=0 bytes_invalid=0 send_seq=69907 receive_seq=69907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998456 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448785 bytes_read=7723831 bytes_retransmit=9 bytes_invalid=0 send_seq=71756 receive_seq=71756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999411 adj=63999580 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=51.4 pwm=0.978 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423981 bytes_read=24421999 bytes_retransmit=9 bytes_invalid=0 send_seq=70260 receive_seq=70260 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999757 adj=31999785 coil_temp=33.7 refs=0 mcu_temp=30.44 supply_voltage=3.014 sysload=0.21 cputime=3389.027 memavail=1409824 print_time=70709.505 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.274
Stats 70705.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=494329 bytes_read=8013181 bytes_retransmit=9 bytes_invalid=0 send_seq=74530 receive_seq=74530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999477 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419646 bytes_read=1294083 bytes_retransmit=0 bytes_invalid=0 send_seq=69908 receive_seq=69908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998436 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448851 bytes_read=7724004 bytes_retransmit=9 bytes_invalid=0 send_seq=71761 receive_seq=71761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999407 adj=63999587 Octopus_V1.1_F446: temp=31.9 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=51.6 pwm=0.978 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423987 bytes_read=24422355 bytes_retransmit=9 bytes_invalid=0 send_seq=70261 receive_seq=70261 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999755 adj=31999804 coil_temp=33.7 refs=0 mcu_temp=30.51 supply_voltage=3.014 sysload=0.21 cputime=3389.068 memavail=1409880 print_time=70710.505 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.292
Stats 70706.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=494531 bytes_read=8013620 bytes_retransmit=9 bytes_invalid=0 send_seq=74545 receive_seq=74545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999470 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=419652 bytes_read=1294111 bytes_retransmit=0 bytes_invalid=0 send_seq=69909 receive_seq=69909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998436 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448910 bytes_read=7724173 bytes_retransmit=9 bytes_invalid=0 send_seq=71765 receive_seq=71765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999404 adj=63999575 Octopus_V1.1_F446: temp=31.9 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=51.7 pwm=0.978 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423993 bytes_read=24422711 bytes_retransmit=9 bytes_invalid=0 send_seq=70262 receive_seq=70262 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999755 adj=31999808 coil_temp=33.8 refs=0 mcu_temp=30.55 supply_voltage=3.014 sysload=0.21 cputime=3389.149 memavail=1409880 print_time=70711.505 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.6 pwm=0.007
Stats 70707.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=494733 bytes_read=8014059 bytes_retransmit=9 bytes_invalid=0 send_seq=74560 receive_seq=74560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999466 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=419658 bytes_read=1294126 bytes_retransmit=0 bytes_invalid=0 send_seq=69910 receive_seq=69910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998437 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=448975 bytes_read=7724346 bytes_retransmit=9 bytes_invalid=0 send_seq=71770 receive_seq=71770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999404 adj=63999578 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=51.8 pwm=0.978 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423999 bytes_read=24423067 bytes_retransmit=9 bytes_invalid=0 send_seq=70263 receive_seq=70263 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999755 adj=31999833 coil_temp=33.8 refs=0 mcu_temp=30.59 supply_voltage=3.014 sysload=0.21 cputime=3389.245 memavail=1409880 print_time=70712.506 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.265
Stats 70708.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=494952 bytes_read=8014558 bytes_retransmit=9 bytes_invalid=0 send_seq=74576 receive_seq=74576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999464 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=419664 bytes_read=1294141 bytes_retransmit=0 bytes_invalid=0 send_seq=69911 receive_seq=69911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998498 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449046 bytes_read=7724550 bytes_retransmit=9 bytes_invalid=0 send_seq=71776 receive_seq=71776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=10 freq=63999410 adj=63999595 Octopus_V1.1_F446: temp=32.1 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=32.6 sd_pos=41100 heater_bed: target=55 temp=52.0 pwm=0.976 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424005 bytes_read=24423423 bytes_retransmit=9 bytes_invalid=0 send_seq=70264 receive_seq=70264 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999754 adj=31999847 coil_temp=33.8 refs=0 mcu_temp=30.63 supply_voltage=3.014 sysload=0.21 cputime=3389.344 memavail=1409888 print_time=70713.506 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.3 pwm=0.091
Stats 70709.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=495154 bytes_read=8014997 bytes_retransmit=9 bytes_invalid=0 send_seq=74591 receive_seq=74591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999464 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=419670 bytes_read=1294156 bytes_retransmit=0 bytes_invalid=0 send_seq=69912 receive_seq=69912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998548 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449103 bytes_read=7724704 bytes_retransmit=9 bytes_invalid=0 send_seq=71780 receive_seq=71780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999410 adj=63999698 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=52.1 pwm=0.976 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424011 bytes_read=24423779 bytes_retransmit=9 bytes_invalid=0 send_seq=70265 receive_seq=70265 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999754 adj=31999849 coil_temp=33.9 refs=0 mcu_temp=30.67 supply_voltage=3.014 sysload=0.19 cputime=3389.437 memavail=1409888 print_time=70714.507 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70710.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=495356 bytes_read=8015436 bytes_retransmit=9 bytes_invalid=0 send_seq=74606 receive_seq=74606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999472 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=419676 bytes_read=1294172 bytes_retransmit=0 bytes_invalid=0 send_seq=69913 receive_seq=69913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998583 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449168 bytes_read=7724863 bytes_retransmit=9 bytes_invalid=0 send_seq=71785 receive_seq=71785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999667 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.8 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=52.2 pwm=0.976 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424017 bytes_read=24424135 bytes_retransmit=9 bytes_invalid=0 send_seq=70266 receive_seq=70266 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999756 adj=31999842 coil_temp=33.9 refs=0 mcu_temp=30.71 supply_voltage=3.014 sysload=0.19 cputime=3389.531 memavail=1409888 print_time=70715.508 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.7 pwm=0.314
Stats 70711.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=495558 bytes_read=8015904 bytes_retransmit=9 bytes_invalid=0 send_seq=74621 receive_seq=74621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999470 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=419682 bytes_read=1294201 bytes_retransmit=0 bytes_invalid=0 send_seq=69914 receive_seq=69914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998337 adj=49998532 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449234 bytes_read=7725051 bytes_retransmit=9 bytes_invalid=0 send_seq=71790 receive_seq=71790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999408 adj=63999594 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=52.3 pwm=0.976 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424023 bytes_read=24424491 bytes_retransmit=9 bytes_invalid=0 send_seq=70267 receive_seq=70267 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999756 adj=31999853 coil_temp=34.0 refs=0 mcu_temp=30.76 supply_voltage=3.014 sysload=0.19 cputime=3389.627 memavail=1409888 print_time=70716.508 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.126
Stats 70712.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=495776 bytes_read=8016348 bytes_retransmit=9 bytes_invalid=0 send_seq=74637 receive_seq=74637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999472 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=419688 bytes_read=1294217 bytes_retransmit=0 bytes_invalid=0 send_seq=69915 receive_seq=69915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998535 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449291 bytes_read=7725219 bytes_retransmit=9 bytes_invalid=0 send_seq=71794 receive_seq=71794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999599 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=52.4 pwm=0.974 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424029 bytes_read=24424847 bytes_retransmit=9 bytes_invalid=0 send_seq=70268 receive_seq=70268 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999756 adj=31999853 coil_temp=34.0 refs=0 mcu_temp=30.83 supply_voltage=3.014 sysload=0.19 cputime=3389.721 memavail=1409888 print_time=70717.509 buffer_time=0.000 print_stall=0 extruder: target=150 temp=152.2 pwm=0.000
Stats 70713.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=495978 bytes_read=8016802 bytes_retransmit=9 bytes_invalid=0 send_seq=74652 receive_seq=74652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999482 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=419694 bytes_read=1294233 bytes_retransmit=0 bytes_invalid=0 send_seq=69916 receive_seq=69916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998565 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449341 bytes_read=7725373 bytes_retransmit=9 bytes_invalid=0 send_seq=71798 receive_seq=71798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999590 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=52.5 pwm=0.974 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424035 bytes_read=24425203 bytes_retransmit=9 bytes_invalid=0 send_seq=70269 receive_seq=70269 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999755 adj=31999845 coil_temp=34.0 refs=0 mcu_temp=30.87 supply_voltage=3.014 sysload=0.19 cputime=3389.816 memavail=1409888 print_time=70718.509 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.1 pwm=0.281
Stats 70714.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=496180 bytes_read=8017270 bytes_retransmit=9 bytes_invalid=0 send_seq=74667 receive_seq=74667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999490 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=419700 bytes_read=1294249 bytes_retransmit=0 bytes_invalid=0 send_seq=69917 receive_seq=69917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998341 adj=49998502 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449407 bytes_read=7725561 bytes_retransmit=9 bytes_invalid=0 send_seq=71803 receive_seq=71803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999411 adj=63999546 Octopus_V1.1_F446: temp=32.1 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=52.7 pwm=0.974 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424041 bytes_read=24425559 bytes_retransmit=9 bytes_invalid=0 send_seq=70270 receive_seq=70270 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999754 adj=31999802 coil_temp=34.0 refs=0 mcu_temp=30.90 supply_voltage=3.014 sysload=0.18 cputime=3389.909 memavail=1409644 print_time=70719.509 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.200
Stats 70715.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=496382 bytes_read=8017709 bytes_retransmit=9 bytes_invalid=0 send_seq=74682 receive_seq=74682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999488 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=419706 bytes_read=1294265 bytes_retransmit=0 bytes_invalid=0 send_seq=69918 receive_seq=69918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998470 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449466 bytes_read=7725715 bytes_retransmit=9 bytes_invalid=0 send_seq=71807 receive_seq=71807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999410 adj=63999547 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=52.8 pwm=0.974 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424047 bytes_read=24425915 bytes_retransmit=9 bytes_invalid=0 send_seq=70271 receive_seq=70271 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999753 adj=31999788 coil_temp=34.1 refs=0 mcu_temp=30.95 supply_voltage=3.014 sysload=0.18 cputime=3390.000 memavail=1409644 print_time=70720.510 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.044
Stats 70716.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=496584 bytes_read=8018148 bytes_retransmit=9 bytes_invalid=0 send_seq=74697 receive_seq=74697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999483 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419712 bytes_read=1294294 bytes_retransmit=0 bytes_invalid=0 send_seq=69919 receive_seq=69919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998503 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=449515 bytes_read=7725869 bytes_retransmit=9 bytes_invalid=0 send_seq=71811 receive_seq=71811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999547 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.8 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=52.9 pwm=0.974 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424053 bytes_read=24426271 bytes_retransmit=9 bytes_invalid=0 send_seq=70272 receive_seq=70272 retransmit_seq=12 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999753 adj=31999794 coil_temp=34.1 refs=0 mcu_temp=30.99 supply_voltage=3.014 sysload=0.18 cputime=3390.089 memavail=1409396 print_time=70721.510 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.132
Stats 70717.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=496802 bytes_read=8018621 bytes_retransmit=9 bytes_invalid=0 send_seq=74713 receive_seq=74713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999483 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419718 bytes_read=1294310 bytes_retransmit=0 bytes_invalid=0 send_seq=69920 receive_seq=69920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998345 adj=49998545 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449565 bytes_read=7726066 bytes_retransmit=9 bytes_invalid=0 send_seq=71815 receive_seq=71815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999406 adj=63999556 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=53.0 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424059 bytes_read=24426627 bytes_retransmit=9 bytes_invalid=0 send_seq=70273 receive_seq=70273 retransmit_seq=12 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999751 adj=31999810 coil_temp=34.2 refs=0 mcu_temp=31.03 supply_voltage=3.014 sysload=0.18 cputime=3390.177 memavail=1409396 print_time=70722.511 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.197
Stats 70718.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=497004 bytes_read=8019067 bytes_retransmit=9 bytes_invalid=0 send_seq=74728 receive_seq=74728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999476 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419724 bytes_read=1294326 bytes_retransmit=0 bytes_invalid=0 send_seq=69921 receive_seq=69921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998346 adj=49998547 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449637 bytes_read=7726225 bytes_retransmit=9 bytes_invalid=0 send_seq=71820 receive_seq=71820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999537 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=53.1 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424065 bytes_read=24426983 bytes_retransmit=9 bytes_invalid=0 send_seq=70274 receive_seq=70274 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999749 adj=31999787 coil_temp=34.2 refs=0 mcu_temp=31.07 supply_voltage=3.014 sysload=0.18 cputime=3390.249 memavail=1409624 print_time=70723.512 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.8 pwm=0.000
Stats 70719.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=497206 bytes_read=8019501 bytes_retransmit=9 bytes_invalid=0 send_seq=74743 receive_seq=74743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999470 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419736 bytes_read=1294358 bytes_retransmit=0 bytes_invalid=0 send_seq=69923 receive_seq=69923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998339 adj=49998583 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449697 bytes_read=7726379 bytes_retransmit=9 bytes_invalid=0 send_seq=71824 receive_seq=71824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999406 adj=63999618 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=53.2 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424071 bytes_read=24427339 bytes_retransmit=9 bytes_invalid=0 send_seq=70275 receive_seq=70275 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999747 adj=31999794 coil_temp=34.2 refs=0 mcu_temp=31.12 supply_voltage=3.014 sysload=0.16 cputime=3390.290 memavail=1409668 print_time=70724.512 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.8 pwm=0.257
Stats 70720.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=497408 bytes_read=8019969 bytes_retransmit=9 bytes_invalid=0 send_seq=74758 receive_seq=74758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999464 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=419742 bytes_read=1294374 bytes_retransmit=0 bytes_invalid=0 send_seq=69924 receive_seq=69924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998475 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449747 bytes_read=7726562 bytes_retransmit=9 bytes_invalid=0 send_seq=71828 receive_seq=71828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999403 adj=63999614 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=33.1 sd_pos=41100 heater_bed: target=55 temp=53.3 pwm=0.979 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424077 bytes_read=24427695 bytes_retransmit=9 bytes_invalid=0 send_seq=70276 receive_seq=70276 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999744 adj=31999783 coil_temp=34.3 refs=0 mcu_temp=31.15 supply_voltage=3.014 sysload=0.16 cputime=3390.330 memavail=1409672 print_time=70725.513 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.150
Stats 70721.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=497626 bytes_read=8020413 bytes_retransmit=9 bytes_invalid=0 send_seq=74774 receive_seq=74774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999456 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=419748 bytes_read=1294403 bytes_retransmit=0 bytes_invalid=0 send_seq=69925 receive_seq=69925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998459 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449804 bytes_read=7726716 bytes_retransmit=9 bytes_invalid=0 send_seq=71832 receive_seq=71832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999400 adj=63999591 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=53.5 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424083 bytes_read=24428051 bytes_retransmit=9 bytes_invalid=0 send_seq=70277 receive_seq=70277 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999742 adj=31999774 coil_temp=34.3 refs=0 mcu_temp=31.20 supply_voltage=3.014 sysload=0.16 cputime=3390.370 memavail=1409672 print_time=70726.514 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.7 pwm=0.000
Stats 70722.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=497828 bytes_read=8020852 bytes_retransmit=9 bytes_invalid=0 send_seq=74789 receive_seq=74789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999450 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=419754 bytes_read=1294419 bytes_retransmit=0 bytes_invalid=0 send_seq=69926 receive_seq=69926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998469 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449869 bytes_read=7726889 bytes_retransmit=9 bytes_invalid=0 send_seq=71837 receive_seq=71837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999398 adj=63999598 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=53.6 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424089 bytes_read=24428407 bytes_retransmit=9 bytes_invalid=0 send_seq=70278 receive_seq=70278 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999740 adj=31999774 coil_temp=34.4 refs=0 mcu_temp=31.24 supply_voltage=3.014 sysload=0.16 cputime=3390.410 memavail=1409176 print_time=70727.514 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.0 pwm=0.257
Stats 70723.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=498030 bytes_read=8021335 bytes_retransmit=9 bytes_invalid=0 send_seq=74804 receive_seq=74804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999518 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=419760 bytes_read=1294435 bytes_retransmit=0 bytes_invalid=0 send_seq=69927 receive_seq=69927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998464 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449935 bytes_read=7727077 bytes_retransmit=9 bytes_invalid=0 send_seq=71842 receive_seq=71842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999396 adj=63999593 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=53.7 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424095 bytes_read=24428763 bytes_retransmit=9 bytes_invalid=0 send_seq=70279 receive_seq=70279 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999737 adj=31999781 coil_temp=34.4 refs=0 mcu_temp=31.27 supply_voltage=3.014 sysload=0.16 cputime=3390.477 memavail=1409176 print_time=70728.515 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.2 pwm=0.129
Stats 70724.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=498232 bytes_read=8021774 bytes_retransmit=9 bytes_invalid=0 send_seq=74819 receive_seq=74819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999510 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=419766 bytes_read=1294451 bytes_retransmit=0 bytes_invalid=0 send_seq=69928 receive_seq=69928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998333 adj=49998191 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=449994 bytes_read=7727231 bytes_retransmit=9 bytes_invalid=0 send_seq=71846 receive_seq=71846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999395 adj=63999193 Octopus_V1.1_F446: temp=32.4 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=53.8 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424101 bytes_read=24429119 bytes_retransmit=9 bytes_invalid=0 send_seq=70280 receive_seq=70280 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999736 adj=31999566 coil_temp=34.4 refs=0 mcu_temp=31.31 supply_voltage=3.014 sysload=0.15 cputime=3390.564 memavail=1408912 print_time=70729.516 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.008
Stats 70725.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=498450 bytes_read=8022218 bytes_retransmit=9 bytes_invalid=0 send_seq=74835 receive_seq=74835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999517 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=419772 bytes_read=1294467 bytes_retransmit=0 bytes_invalid=0 send_seq=69929 receive_seq=69929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998300 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450059 bytes_read=7727385 bytes_retransmit=9 bytes_invalid=0 send_seq=71851 receive_seq=71851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999397 adj=63999316 Octopus_V1.1_F446: temp=32.4 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=53.9 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424113 bytes_read=24429491 bytes_retransmit=9 bytes_invalid=0 send_seq=70282 receive_seq=70282 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999735 adj=31999638 coil_temp=34.5 refs=0 mcu_temp=31.35 supply_voltage=3.014 sysload=0.15 cputime=3390.656 memavail=1408964 print_time=70730.516 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.283
Stats 70726.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=498652 bytes_read=8022686 bytes_retransmit=9 bytes_invalid=0 send_seq=74850 receive_seq=74850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999516 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=419778 bytes_read=1294496 bytes_retransmit=0 bytes_invalid=0 send_seq=69930 receive_seq=69930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998327 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450120 bytes_read=7727559 bytes_retransmit=9 bytes_invalid=0 send_seq=71855 receive_seq=71855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999404 adj=63999358 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=54.1 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424119 bytes_read=24429841 bytes_retransmit=9 bytes_invalid=0 send_seq=70283 receive_seq=70283 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999734 adj=31999636 coil_temp=34.5 refs=0 mcu_temp=31.42 supply_voltage=3.014 sysload=0.15 cputime=3390.749 memavail=1408964 print_time=70731.517 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.5 pwm=0.060
Stats 70727.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=498854 bytes_read=8023125 bytes_retransmit=9 bytes_invalid=0 send_seq=74865 receive_seq=74865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999507 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=419784 bytes_read=1294512 bytes_retransmit=0 bytes_invalid=0 send_seq=69931 receive_seq=69931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998399 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450177 bytes_read=7727720 bytes_retransmit=9 bytes_invalid=0 send_seq=71859 receive_seq=71859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999403 adj=63999531 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=54.2 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424125 bytes_read=24430186 bytes_retransmit=9 bytes_invalid=0 send_seq=70284 receive_seq=70284 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999733 adj=31999676 coil_temp=34.5 refs=0 mcu_temp=31.47 supply_voltage=3.014 sysload=0.15 cputime=3390.839 memavail=1408964 print_time=70732.518 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70728.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=499056 bytes_read=8023579 bytes_retransmit=9 bytes_invalid=0 send_seq=74880 receive_seq=74880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999500 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=419790 bytes_read=1294528 bytes_retransmit=0 bytes_invalid=0 send_seq=69932 receive_seq=69932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998340 adj=49998481 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450242 bytes_read=7727872 bytes_retransmit=9 bytes_invalid=0 send_seq=71864 receive_seq=71864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999403 adj=63999579 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=54.3 pwm=0.962 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424131 bytes_read=24430530 bytes_retransmit=9 bytes_invalid=0 send_seq=70285 receive_seq=70285 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999733 adj=31999719 coil_temp=34.6 refs=0 mcu_temp=31.52 supply_voltage=3.014 sysload=0.15 cputime=3390.931 memavail=1408964 print_time=70733.518 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.360
Stats 70729.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=499269 bytes_read=8024047 bytes_retransmit=9 bytes_invalid=0 send_seq=74895 receive_seq=74895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999495 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=419796 bytes_read=1294544 bytes_retransmit=0 bytes_invalid=0 send_seq=69933 receive_seq=69933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998344 adj=49998545 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450307 bytes_read=7728055 bytes_retransmit=9 bytes_invalid=0 send_seq=71869 receive_seq=71869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=63999401 adj=63999616 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=54.4 pwm=0.917 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424137 bytes_read=24430875 bytes_retransmit=9 bytes_invalid=0 send_seq=70286 receive_seq=70286 retransmit_seq=12 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999732 adj=31999770 coil_temp=34.6 refs=0 mcu_temp=31.56 supply_voltage=3.014 sysload=0.14 cputime=3391.026 memavail=1408976 print_time=70734.518 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.8 pwm=0.000
RatOS:: Waiting for extruder to be preheated...
RatOS | TEMPERATURE_WAIT:: Waiting for sensor: extruder, MINIMUM: 150, MAXIMUM: 155
RatOS:: please wait...
RatOS | TEMPERATURE_WAIT:: Temperature for toolhead T0 reached.
RatOS:: Adjusting Z tilt...
Stats 70730.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=503564 bytes_read=8024816 bytes_retransmit=9 bytes_invalid=0 send_seq=74976 receive_seq=74976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999483 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=419802 bytes_read=1294560 bytes_retransmit=0 bytes_invalid=0 send_seq=69934 receive_seq=69934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998342 adj=49998614 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450349 bytes_read=7728204 bytes_retransmit=9 bytes_invalid=0 send_seq=71872 receive_seq=71872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999398 adj=63999612 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=54.6 pwm=0.917 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424150 bytes_read=24432890 bytes_retransmit=9 bytes_invalid=0 send_seq=70288 receive_seq=70288 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999730 adj=31999775 coil_temp=34.7 refs=3 mcu_temp=31.61 supply_voltage=3.014 sysload=0.14 cputime=3391.310 memavail=1408976 print_time=70737.231 buffer_time=1.246 print_stall=0 extruder: target=150 temp=151.6 pwm=0.000
Stats 70731.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=504717 bytes_read=8025340 bytes_retransmit=9 bytes_invalid=0 send_seq=75008 receive_seq=75008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999473 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000020 bytes_write=419808 bytes_read=1294589 bytes_retransmit=0 bytes_invalid=0 send_seq=69935 receive_seq=69935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998338 adj=49998557 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450414 bytes_read=7728363 bytes_retransmit=9 bytes_invalid=0 send_seq=71877 receive_seq=71877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999395 adj=63999607 Octopus_V1.1_F446: temp=32.9 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=54.5 pwm=0.969 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424156 bytes_read=24435915 bytes_retransmit=9 bytes_invalid=0 send_seq=70289 receive_seq=70289 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999728 adj=31999808 coil_temp=34.7 refs=3 mcu_temp=31.65 supply_voltage=3.014 sysload=0.14 cputime=3391.473 memavail=1408976 print_time=70737.231 buffer_time=0.246 print_stall=0 extruder: target=150 temp=150.0 pwm=0.279
Stats 70732.5: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=506297 bytes_read=8027096 bytes_retransmit=9 bytes_invalid=0 send_seq=75107 receive_seq=75107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999460 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000020 bytes_write=419814 bytes_read=1294605 bytes_retransmit=0 bytes_invalid=0 send_seq=69936 receive_seq=69936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998544 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=450480 bytes_read=7728565 bytes_retransmit=9 bytes_invalid=0 send_seq=71882 receive_seq=71882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999392 adj=63999612 Octopus_V1.1_F446: temp=32.7 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=54.9 pwm=0.831 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=424890 bytes_read=24440071 bytes_retransmit=9 bytes_invalid=0 send_seq=70355 receive_seq=70355 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999727 adj=31999806 coil_temp=34.6 refs=2 mcu_temp=31.72 supply_voltage=3.014 sysload=0.14 cputime=3391.644 memavail=1408976 print_time=70738.156 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.4 pwm=0.089
Stats 70733.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000011 mcu_task_stddev=0.000016 bytes_write=508312 bytes_read=8029776 bytes_retransmit=9 bytes_invalid=0 send_seq=75255 receive_seq=75255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999450 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000020 bytes_write=419820 bytes_read=1294621 bytes_retransmit=0 bytes_invalid=0 send_seq=69937 receive_seq=69937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998331 adj=49998525 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=450537 bytes_read=7728719 bytes_retransmit=9 bytes_invalid=0 send_seq=71886 receive_seq=71886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999389 adj=63999635 Octopus_V1.1_F446: temp=32.9 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=54.8 pwm=0.952 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=426062 bytes_read=24445016 bytes_retransmit=9 bytes_invalid=0 send_seq=70463 receive_seq=70463 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999724 adj=31999824 coil_temp=34.6 refs=3 mcu_temp=31.74 supply_voltage=3.014 sysload=0.14 cputime=3391.865 memavail=1408976 print_time=70739.196 buffer_time=0.210 print_stall=0 extruder: target=150 temp=151.7 pwm=0.000
probe at 30.000,30.000,2.051 is z=1.967659
Stats 70734.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000011 mcu_task_stddev=0.000016 bytes_write=515739 bytes_read=8030810 bytes_retransmit=9 bytes_invalid=0 send_seq=75389 receive_seq=75389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999444 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000020 bytes_write=419826 bytes_read=1294637 bytes_retransmit=0 bytes_invalid=0 send_seq=69938 receive_seq=69938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998329 adj=49998511 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=450602 bytes_read=7728878 bytes_retransmit=9 bytes_invalid=0 send_seq=71891 receive_seq=71891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999392 adj=63999635 Octopus_V1.1_F446: temp=33.0 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=54.8 pwm=0.964 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=426068 bytes_read=24448049 bytes_retransmit=9 bytes_invalid=0 send_seq=70464 receive_seq=70464 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999723 adj=31999836 coil_temp=34.6 refs=3 mcu_temp=31.77 supply_voltage=3.014 sysload=0.12 cputime=3392.115 memavail=1409180 print_time=70740.767 buffer_time=0.781 print_stall=0 extruder: target=150 temp=150.1 pwm=0.266
Stats 70735.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000011 mcu_task_stddev=0.000016 bytes_write=517472 bytes_read=8031418 bytes_retransmit=9 bytes_invalid=0 send_seq=75432 receive_seq=75432 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999490 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000020 bytes_write=419832 bytes_read=1294653 bytes_retransmit=0 bytes_invalid=0 send_seq=69939 receive_seq=69939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998328 adj=49998492 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=450652 bytes_read=7729061 bytes_retransmit=9 bytes_invalid=0 send_seq=71895 receive_seq=71895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=63999392 adj=63999688 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=55.1 pwm=0.852 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=426115 bytes_read=24451135 bytes_retransmit=9 bytes_invalid=0 send_seq=70467 receive_seq=70467 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999721 adj=31999823 coil_temp=34.6 refs=2 mcu_temp=31.79 supply_voltage=3.014 sysload=0.12 cputime=3392.346 memavail=1404956 print_time=70741.178 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.218
Stats 70736.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000011 mcu_task_stddev=0.000016 bytes_write=519717 bytes_read=8034323 bytes_retransmit=9 bytes_invalid=0 send_seq=75593 receive_seq=75593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999477 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419838 bytes_read=1294682 bytes_retransmit=0 bytes_invalid=0 send_seq=69940 receive_seq=69940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998326 adj=49998279 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=450709 bytes_read=7729215 bytes_retransmit=9 bytes_invalid=0 send_seq=71899 receive_seq=71899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999389 adj=63999433 Octopus_V1.1_F446: temp=33.0 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=55.2 pwm=0.801 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=427609 bytes_read=24456581 bytes_retransmit=9 bytes_invalid=0 send_seq=70592 receive_seq=70592 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999719 adj=31999665 coil_temp=34.5 refs=2 mcu_temp=31.82 supply_voltage=3.014 sysload=0.12 cputime=3392.551 memavail=1410984 print_time=70742.178 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.8 pwm=0.000
probe at 250.000,450.000,2.006 is z=1.950848
Stats 70737.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000011 mcu_task_stddev=0.000016 bytes_write=527878 bytes_read=8036301 bytes_retransmit=9 bytes_invalid=0 send_seq=75783 receive_seq=75783 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=179999468 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419844 bytes_read=1294698 bytes_retransmit=0 bytes_invalid=0 send_seq=69941 receive_seq=69941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998324 adj=49998348 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450758 bytes_read=7729383 bytes_retransmit=9 bytes_invalid=0 send_seq=71903 receive_seq=71903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999387 adj=63999493 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=55.2 pwm=0.910 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=428117 bytes_read=24460450 bytes_retransmit=9 bytes_invalid=0 send_seq=70636 receive_seq=70636 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999717 adj=31999724 coil_temp=34.6 refs=3 mcu_temp=31.82 supply_voltage=3.014 sysload=0.12 cputime=3392.819 memavail=1410984 print_time=70744.289 buffer_time=1.300 print_stall=0 extruder: target=150 temp=150.9 pwm=0.068
Stats 70738.5: gcodein=0  mcu: mcu_awake=0.044 mcu_task_avg=0.000023 mcu_task_stddev=0.000067 bytes_write=528087 bytes_read=8036786 bytes_retransmit=9 bytes_invalid=0 send_seq=75798 receive_seq=75798 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999546 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419850 bytes_read=1294714 bytes_retransmit=0 bytes_invalid=0 send_seq=69942 receive_seq=69942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998322 adj=49998422 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450840 bytes_read=7729576 bytes_retransmit=9 bytes_invalid=0 send_seq=71909 receive_seq=71909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999386 adj=63999559 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=55.2 pwm=0.910 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=428123 bytes_read=24463526 bytes_retransmit=9 bytes_invalid=0 send_seq=70637 receive_seq=70637 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999716 adj=31999775 coil_temp=34.6 refs=3 mcu_temp=31.82 supply_voltage=3.014 sysload=0.12 cputime=3392.987 memavail=1410984 print_time=70744.289 buffer_time=0.300 print_stall=0 extruder: target=150 temp=149.4 pwm=0.348
Stats 70739.5: gcodein=0  mcu: mcu_awake=0.044 mcu_task_avg=0.000023 mcu_task_stddev=0.000067 bytes_write=530726 bytes_read=8038460 bytes_retransmit=9 bytes_invalid=0 send_seq=75906 receive_seq=75906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999531 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419856 bytes_read=1294730 bytes_retransmit=0 bytes_invalid=0 send_seq=69943 receive_seq=69943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998038 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450913 bytes_read=7729735 bytes_retransmit=9 bytes_invalid=0 send_seq=71914 receive_seq=71914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999384 adj=63999090 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=55.3 pwm=0.884 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=428835 bytes_read=24467662 bytes_retransmit=9 bytes_invalid=0 send_seq=70696 receive_seq=70696 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999713 adj=31999527 coil_temp=34.7 refs=2 mcu_temp=31.82 supply_voltage=3.014 sysload=0.11 cputime=3393.167 memavail=1410988 print_time=70745.168 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.8 pwm=0.000
Stats 70740.5: gcodein=0  mcu: mcu_awake=0.044 mcu_task_avg=0.000023 mcu_task_stddev=0.000067 bytes_write=532847 bytes_read=8041276 bytes_retransmit=9 bytes_invalid=0 send_seq=76062 receive_seq=76062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999515 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419862 bytes_read=1294746 bytes_retransmit=0 bytes_invalid=0 send_seq=69944 receive_seq=69944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998158 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=450947 bytes_read=7729884 bytes_retransmit=9 bytes_invalid=0 send_seq=71917 receive_seq=71917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999256 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=55.4 pwm=0.884 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=430207 bytes_read=24472915 bytes_retransmit=9 bytes_invalid=0 send_seq=70812 receive_seq=70812 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999712 adj=31999592 coil_temp=34.6 refs=3 mcu_temp=31.83 supply_voltage=3.014 sysload=0.11 cputime=3393.444 memavail=1410988 print_time=70746.258 buffer_time=0.269 print_stall=0 extruder: target=150 temp=151.2 pwm=0.000
probe at 470.000,30.000,2.033 is z=1.963406
Calculating bed tilt with: [[30.000000003501555, 29.99999999935426, 2.083789085951326], [249.99999999989086, 449.99999999719876, 2.054662709955468], [470.00000000064574, 29.99999999935426, 2.069603963647334]]
Coordinate descent initial error: 0.014853334539653693
Coordinate descent best_err: 1.9356268824107223e-10  rounds: 205
Calculated bed tilt parameters: {'x_adjust': -3.2224848211954e-05, 'y_adjust': -5.2492255329401094e-05, 'z_adjust': 2.086336394698358}
Making the following Z adjustments:
stepper_z = 0.087517
stepper_z1 = 0.053215
stepper_z2 = 0.071405
Retries: 0/10 Probed points range: 0.029126 tolerance: 0.020000
Stats 70741.5: gcodein=0  mcu: mcu_awake=0.044 mcu_task_avg=0.000023 mcu_task_stddev=0.000067 bytes_write=538261 bytes_read=8042174 bytes_retransmit=9 bytes_invalid=0 send_seq=76163 receive_seq=76163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999505 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=419868 bytes_read=1294775 bytes_retransmit=0 bytes_invalid=0 send_seq=69945 receive_seq=69945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998274 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451012 bytes_read=7730072 bytes_retransmit=9 bytes_invalid=0 send_seq=71922 receive_seq=71922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999399 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=55.6 pwm=0.777 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=430213 bytes_read=24475991 bytes_retransmit=9 bytes_invalid=0 send_seq=70813 receive_seq=70813 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999710 adj=31999667 coil_temp=34.7 refs=3 mcu_temp=31.84 supply_voltage=3.014 sysload=0.11 cputime=3393.760 memavail=1410988 print_time=70747.919 buffer_time=0.929 print_stall=0 extruder: target=150 temp=149.5 pwm=0.368
Stats 70742.5: gcodein=0  mcu: mcu_awake=0.044 mcu_task_avg=0.000023 mcu_task_stddev=0.000067 bytes_write=539192 bytes_read=8042681 bytes_retransmit=9 bytes_invalid=0 send_seq=76193 receive_seq=76193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999492 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=419874 bytes_read=1294791 bytes_retransmit=0 bytes_invalid=0 send_seq=69946 receive_seq=69946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998316 adj=49998398 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451074 bytes_read=7730245 bytes_retransmit=9 bytes_invalid=0 send_seq=71927 receive_seq=71927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999522 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=55.6 pwm=0.868 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=430265 bytes_read=24479082 bytes_retransmit=9 bytes_invalid=0 send_seq=70817 receive_seq=70817 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999710 adj=31999722 coil_temp=34.6 refs=2 mcu_temp=31.84 supply_voltage=3.014 sysload=0.11 cputime=3393.919 memavail=1410764 print_time=70748.239 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70743.5: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000021 mcu_task_stddev=0.000059 bytes_write=541339 bytes_read=8045167 bytes_retransmit=9 bytes_invalid=0 send_seq=76336 receive_seq=76336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999478 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=419880 bytes_read=1294807 bytes_retransmit=0 bytes_invalid=0 send_seq=69947 receive_seq=69947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998315 adj=49998435 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451108 bytes_read=7730394 bytes_retransmit=9 bytes_invalid=0 send_seq=71930 receive_seq=71930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999562 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=55.7 pwm=0.844 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=431531 bytes_read=24484153 bytes_retransmit=9 bytes_invalid=0 send_seq=70923 receive_seq=70923 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999708 adj=31999761 coil_temp=34.6 refs=2 mcu_temp=31.84 supply_voltage=3.014 sysload=0.11 cputime=3394.112 memavail=1410764 print_time=70749.189 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
probe at 30.000,30.000,1.967 is z=1.964507
Stats 70744.5: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000021 mcu_task_stddev=0.000059 bytes_write=549793 bytes_read=8047574 bytes_retransmit=9 bytes_invalid=0 send_seq=76550 receive_seq=76550 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=179999464 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=419886 bytes_read=1294823 bytes_retransmit=0 bytes_invalid=0 send_seq=69948 receive_seq=69948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998313 adj=49998406 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451184 bytes_read=7730582 bytes_retransmit=9 bytes_invalid=0 send_seq=71935 receive_seq=71935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999383 adj=63999530 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=55.9 pwm=0.764 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=432279 bytes_read=24488432 bytes_retransmit=9 bytes_invalid=0 send_seq=70987 receive_seq=70987 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999707 adj=31999734 coil_temp=34.6 refs=3 mcu_temp=31.83 supply_voltage=3.014 sysload=0.11 cputime=3394.378 memavail=1410272 print_time=70751.451 buffer_time=1.456 print_stall=0 extruder: target=150 temp=149.5 pwm=0.349
Stats 70745.5: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000021 mcu_task_stddev=0.000059 bytes_write=550039 bytes_read=8048018 bytes_retransmit=9 bytes_invalid=0 send_seq=76566 receive_seq=76566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999462 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=419892 bytes_read=1294839 bytes_retransmit=0 bytes_invalid=0 send_seq=69949 receive_seq=69949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998312 adj=49998475 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451273 bytes_read=7730746 bytes_retransmit=9 bytes_invalid=0 send_seq=71941 receive_seq=71941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999690 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=55.9 pwm=0.825 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=432285 bytes_read=24491508 bytes_retransmit=9 bytes_invalid=0 send_seq=70988 receive_seq=70988 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999705 adj=31999792 coil_temp=34.6 refs=3 mcu_temp=31.84 supply_voltage=3.014 sysload=0.11 cputime=3394.551 memavail=1410288 print_time=70751.451 buffer_time=0.455 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70746.5: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000021 mcu_task_stddev=0.000059 bytes_write=552335 bytes_read=8049283 bytes_retransmit=9 bytes_invalid=0 send_seq=76651 receive_seq=76651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999485 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=419898 bytes_read=1294868 bytes_retransmit=0 bytes_invalid=0 send_seq=69950 receive_seq=69950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998312 adj=49998465 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451307 bytes_read=7730895 bytes_retransmit=9 bytes_invalid=0 send_seq=71944 receive_seq=71944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999670 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=33.6 sd_pos=41100 heater_bed: target=55 temp=56.0 pwm=0.758 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=432733 bytes_read=24495254 bytes_retransmit=9 bytes_invalid=0 send_seq=71025 receive_seq=71025 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999704 adj=31999776 coil_temp=34.6 refs=2 mcu_temp=31.84 supply_voltage=3.014 sysload=0.11 cputime=3394.826 memavail=1410288 print_time=70752.182 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70747.5: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000021 mcu_task_stddev=0.000059 bytes_write=554730 bytes_read=8052408 bytes_retransmit=9 bytes_invalid=0 send_seq=76823 receive_seq=76823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999473 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=419904 bytes_read=1294884 bytes_retransmit=0 bytes_invalid=0 send_seq=69951 receive_seq=69951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998313 adj=49998371 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451388 bytes_read=7731102 bytes_retransmit=9 bytes_invalid=0 send_seq=71950 receive_seq=71950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999485 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.2 pwm=0.752 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=434363 bytes_read=24500964 bytes_retransmit=9 bytes_invalid=0 send_seq=71162 receive_seq=71162 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999703 adj=31999701 coil_temp=34.6 refs=2 mcu_temp=31.83 supply_voltage=3.014 sysload=0.11 cputime=3395.241 memavail=1410288 print_time=70753.255 buffer_time=0.250 print_stall=0 extruder: target=150 temp=149.5 pwm=0.361
probe at 250.000,450.000,1.960 is z=1.957745
Stats 70748.5: gcodein=0  mcu: mcu_awake=0.033 mcu_task_avg=0.000016 mcu_task_stddev=0.000048 bytes_write=562231 bytes_read=8053593 bytes_retransmit=9 bytes_invalid=0 send_seq=76965 receive_seq=76965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999465 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=419910 bytes_read=1294900 bytes_retransmit=0 bytes_invalid=0 send_seq=69952 receive_seq=69952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998311 adj=49998451 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451466 bytes_read=7731266 bytes_retransmit=9 bytes_invalid=0 send_seq=71956 receive_seq=71956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999562 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.0 pwm=0.841 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=434375 bytes_read=24504045 bytes_retransmit=9 bytes_invalid=0 send_seq=71164 receive_seq=71164 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999702 adj=31999744 coil_temp=34.6 refs=3 mcu_temp=31.82 supply_voltage=3.014 sysload=0.11 cputime=3395.600 memavail=1410288 print_time=70754.996 buffer_time=0.991 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
Stats 70749.5: gcodein=0  mcu: mcu_awake=0.033 mcu_task_avg=0.000016 mcu_task_stddev=0.000048 bytes_write=563641 bytes_read=8054137 bytes_retransmit=9 bytes_invalid=0 send_seq=77001 receive_seq=77001 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999479 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=419916 bytes_read=1294916 bytes_retransmit=0 bytes_invalid=0 send_seq=69953 receive_seq=69953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998311 adj=49998472 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451500 bytes_read=7731415 bytes_retransmit=9 bytes_invalid=0 send_seq=71959 receive_seq=71959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999606 Octopus_V1.1_F446: temp=34.1 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=56.2 pwm=0.813 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=434381 bytes_read=24507121 bytes_retransmit=9 bytes_invalid=0 send_seq=71165 receive_seq=71165 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999700 adj=31999769 coil_temp=34.6 refs=3 mcu_temp=31.83 supply_voltage=3.014 sysload=0.10 cputime=3395.762 memavail=1410288 print_time=70754.996 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.1 pwm=0.000
Stats 70750.5: gcodein=0  mcu: mcu_awake=0.033 mcu_task_avg=0.000016 mcu_task_stddev=0.000048 bytes_write=565769 bytes_read=8056554 bytes_retransmit=9 bytes_invalid=0 send_seq=77137 receive_seq=77137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999465 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=419922 bytes_read=1294932 bytes_retransmit=0 bytes_invalid=0 send_seq=69954 receive_seq=69954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998309 adj=49998399 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451565 bytes_read=7731603 bytes_retransmit=9 bytes_invalid=0 send_seq=71964 receive_seq=71964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999511 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.3 pwm=0.750 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=435585 bytes_read=24512050 bytes_retransmit=9 bytes_invalid=0 send_seq=71265 receive_seq=71265 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999698 adj=31999705 coil_temp=34.7 refs=2 mcu_temp=31.84 supply_voltage=3.014 sysload=0.10 cputime=3395.958 memavail=1410388 print_time=70756.223 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.333
probe at 470.000,30.000,1.966 is z=1.960831
Calculating bed tilt with: [[30.000000003501555, 29.99999999935426, 2.002590741067152], [249.99999999989086, 449.99999999719876, 2.002164400567921], [470.00000000064574, 29.99999999935426, 2.0056409659241377]]
Coordinate descent initial error: 4.321706565272821e-05
Coordinate descent best_err: 1.2370779416202774e-10  rounds: 190
Calculated bed tilt parameters: {'x_adjust': 6.91879399742806e-06, 'y_adjust': -4.625502959187698e-06, 'z_adjust': 2.0025262890673323}
Making the following Z adjustments:
stepper_z = 0.002630
stepper_z1 = 0.002047
stepper_z2 = 0.006090
Retries: 1/10 Probed points range: 0.003477 tolerance: 0.020000
RatOS:: Rehoming Z after Z tilt adjustment...
Stats 70751.5: gcodein=0  mcu: mcu_awake=0.033 mcu_task_avg=0.000016 mcu_task_stddev=0.000048 bytes_write=569394 bytes_read=8058726 bytes_retransmit=9 bytes_invalid=0 send_seq=77279 receive_seq=77279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=179999456 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419928 bytes_read=1294961 bytes_retransmit=0 bytes_invalid=0 send_seq=69955 receive_seq=69955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998308 adj=49998454 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451637 bytes_read=7731762 bytes_retransmit=9 bytes_invalid=0 send_seq=71969 receive_seq=71969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999594 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.4 pwm=0.750 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=436472 bytes_read=24516531 bytes_retransmit=9 bytes_invalid=0 send_seq=71341 receive_seq=71341 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999737 coil_temp=34.7 refs=0 mcu_temp=31.84 supply_voltage=3.014 sysload=0.10 cputime=3396.202 memavail=1410420 print_time=70757.772 buffer_time=0.746 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
RatOS:: Homing Z
Stats 70752.5: gcodein=0  mcu: mcu_awake=0.033 mcu_task_avg=0.000016 mcu_task_stddev=0.000048 bytes_write=572386 bytes_read=8059419 bytes_retransmit=9 bytes_invalid=0 send_seq=77339 receive_seq=77339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=179999458 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419934 bytes_read=1294977 bytes_retransmit=0 bytes_invalid=0 send_seq=69956 receive_seq=69956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998307 adj=49998477 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451686 bytes_read=7731930 bytes_retransmit=9 bytes_invalid=0 send_seq=71973 receive_seq=71973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999622 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=56.4 pwm=0.750 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=436533 bytes_read=24516931 bytes_retransmit=9 bytes_invalid=0 send_seq=71346 receive_seq=71346 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999763 coil_temp=34.7 refs=0 mcu_temp=31.85 supply_voltage=3.014 sysload=0.10 cputime=3396.296 memavail=1404120 print_time=70758.744 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.7 pwm=0.090
Stats 70753.5: gcodein=0  mcu: mcu_awake=0.039 mcu_task_avg=0.000024 mcu_task_stddev=0.000071 bytes_write=573575 bytes_read=8060719 bytes_retransmit=9 bytes_invalid=0 send_seq=77408 receive_seq=77408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999465 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419940 bytes_read=1294993 bytes_retransmit=0 bytes_invalid=0 send_seq=69957 receive_seq=69957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998306 adj=49998448 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451783 bytes_read=7732128 bytes_retransmit=9 bytes_invalid=0 send_seq=71980 receive_seq=71980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999691 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.651 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=437019 bytes_read=24518061 bytes_retransmit=9 bytes_invalid=0 send_seq=71387 receive_seq=71387 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999771 coil_temp=34.6 refs=0 mcu_temp=31.87 supply_voltage=3.014 sysload=0.10 cputime=3396.413 memavail=1410164 print_time=70759.244 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.297
Stats 70754.5: gcodein=0  mcu: mcu_awake=0.039 mcu_task_avg=0.000024 mcu_task_stddev=0.000071 bytes_write=575883 bytes_read=8063775 bytes_retransmit=9 bytes_invalid=0 send_seq=77574 receive_seq=77574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999457 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419946 bytes_read=1295009 bytes_retransmit=0 bytes_invalid=0 send_seq=69958 receive_seq=69958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998312 adj=49998397 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451847 bytes_read=7732287 bytes_retransmit=9 bytes_invalid=0 send_seq=71985 receive_seq=71985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999604 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.651 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=438621 bytes_read=24520958 bytes_retransmit=9 bytes_invalid=0 send_seq=71521 receive_seq=71521 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999756 coil_temp=34.6 refs=0 mcu_temp=31.88 supply_voltage=3.014 sysload=0.33 cputime=3396.643 memavail=1411764 print_time=70760.244 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.9 pwm=0.022
Stats 70755.5: gcodein=0  mcu: mcu_awake=0.039 mcu_task_avg=0.000024 mcu_task_stddev=0.000071 bytes_write=577842 bytes_read=8065961 bytes_retransmit=9 bytes_invalid=0 send_seq=77695 receive_seq=77695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999448 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=419952 bytes_read=1295025 bytes_retransmit=0 bytes_invalid=0 send_seq=69959 receive_seq=69959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998317 adj=49998542 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451896 bytes_read=7732441 bytes_retransmit=9 bytes_invalid=0 send_seq=71989 receive_seq=71989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999640 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.723 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=439573 bytes_read=24523842 bytes_retransmit=9 bytes_invalid=0 send_seq=71603 receive_seq=71603 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999775 coil_temp=34.7 refs=1 mcu_temp=31.89 supply_voltage=3.014 sysload=0.33 cputime=3396.942 memavail=1411820 print_time=70761.605 buffer_time=0.574 print_stall=0 extruder: target=150 temp=150.6 pwm=0.102
Stats 70756.5: gcodein=0  mcu: mcu_awake=0.039 mcu_task_avg=0.000024 mcu_task_stddev=0.000071 bytes_write=582269 bytes_read=8066745 bytes_retransmit=9 bytes_invalid=0 send_seq=77779 receive_seq=77779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999439 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000014 bytes_write=419958 bytes_read=1295054 bytes_retransmit=0 bytes_invalid=0 send_seq=69960 receive_seq=69960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998641 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=451993 bytes_read=7732639 bytes_retransmit=9 bytes_invalid=0 send_seq=71996 receive_seq=71996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999660 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.723 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=439593 bytes_read=24526870 bytes_retransmit=9 bytes_invalid=0 send_seq=71606 receive_seq=71606 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999814 coil_temp=34.8 refs=1 mcu_temp=31.91 supply_voltage=3.014 sysload=0.33 cputime=3397.267 memavail=1411820 print_time=70764.069 buffer_time=2.037 print_stall=0 extruder: target=150 temp=149.5 pwm=0.308
Stats 70757.5: gcodein=0  mcu: mcu_awake=0.039 mcu_task_avg=0.000024 mcu_task_stddev=0.000071 bytes_write=582487 bytes_read=8067189 bytes_retransmit=9 bytes_invalid=0 send_seq=77795 receive_seq=77795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999430 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000014 bytes_write=419964 bytes_read=1295070 bytes_retransmit=0 bytes_invalid=0 send_seq=69961 receive_seq=69961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998317 adj=49998573 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=452070 bytes_read=7732817 bytes_retransmit=9 bytes_invalid=0 send_seq=72002 receive_seq=72002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999640 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.8 pwm=0.609 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=439599 bytes_read=24529946 bytes_retransmit=9 bytes_invalid=0 send_seq=71607 receive_seq=71607 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999695 adj=31999817 coil_temp=34.8 refs=1 mcu_temp=31.93 supply_voltage=3.014 sysload=0.33 cputime=3397.414 memavail=1411820 print_time=70764.069 buffer_time=1.037 print_stall=0 extruder: target=150 temp=151.3 pwm=0.000
Stats 70758.5: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000010 mcu_task_stddev=0.000016 bytes_write=583787 bytes_read=8067768 bytes_retransmit=9 bytes_invalid=0 send_seq=77829 receive_seq=77829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999422 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000014 bytes_write=419970 bytes_read=1295086 bytes_retransmit=0 bytes_invalid=0 send_seq=69962 receive_seq=69962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998316 adj=49998587 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=452119 bytes_read=7732985 bytes_retransmit=9 bytes_invalid=0 send_seq=72006 receive_seq=72006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999656 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.7 pwm=0.700 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=439605 bytes_read=24533022 bytes_retransmit=9 bytes_invalid=0 send_seq=71608 receive_seq=71608 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999694 adj=31999821 coil_temp=34.8 refs=1 mcu_temp=31.96 supply_voltage=3.014 sysload=0.33 cputime=3397.557 memavail=1411820 print_time=70764.069 buffer_time=0.037 print_stall=0 extruder: target=150 temp=150.8 pwm=0.065
Stats 70759.5: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000010 mcu_task_stddev=0.000016 bytes_write=585637 bytes_read=8069946 bytes_retransmit=9 bytes_invalid=0 send_seq=77951 receive_seq=77951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999412 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000014 bytes_write=419976 bytes_read=1295102 bytes_retransmit=0 bytes_invalid=0 send_seq=69963 receive_seq=69963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998315 adj=49998601 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=452217 bytes_read=7733169 bytes_retransmit=9 bytes_invalid=0 send_seq=72013 receive_seq=72013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999375 adj=63999676 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=56.9 pwm=0.650 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=440689 bytes_read=24537750 bytes_retransmit=9 bytes_invalid=0 send_seq=71699 receive_seq=71699 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999693 adj=31999828 coil_temp=34.8 refs=1 mcu_temp=31.99 supply_voltage=3.014 sysload=0.30 cputime=3397.752 memavail=1411568 print_time=70765.222 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.4 pwm=0.341
Stats 70760.5: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000010 mcu_task_stddev=0.000016 bytes_write=588022 bytes_read=8073026 bytes_retransmit=9 bytes_invalid=0 send_seq=78119 receive_seq=78119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999401 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000014 bytes_write=419982 bytes_read=1295118 bytes_retransmit=0 bytes_invalid=0 send_seq=69964 receive_seq=69964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998314 adj=49998628 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=452279 bytes_read=7733328 bytes_retransmit=9 bytes_invalid=0 send_seq=72018 receive_seq=72018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999373 adj=63999728 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.9 pwm=0.650 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442315 bytes_read=24543363 bytes_retransmit=9 bytes_invalid=0 send_seq=71835 receive_seq=71835 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999692 adj=31999840 coil_temp=34.8 refs=1 mcu_temp=32.01 supply_voltage=3.014 sysload=0.30 cputime=3397.972 memavail=1411568 print_time=70766.222 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.6 pwm=0.000
probe at 50.000,10.000 is z=0.029606
Result is z=0.029606
Last reading: 5408112.53Hz, 34.87C, -infmm
RatOS:: Auto calibration nozzle wipe with probe result 0.02960602138479196...
Stats 70761.5: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000010 mcu_task_stddev=0.000016 bytes_write=590391 bytes_read=8073949 bytes_retransmit=9 bytes_invalid=0 send_seq=78184 receive_seq=78184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999392 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419988 bytes_read=1295147 bytes_retransmit=0 bytes_invalid=0 send_seq=69965 receive_seq=69965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998313 adj=49998615 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=452328 bytes_read=7733496 bytes_retransmit=9 bytes_invalid=0 send_seq=72022 receive_seq=72022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999372 adj=63999725 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.650 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442454 bytes_read=24545060 bytes_retransmit=9 bytes_invalid=0 send_seq=71850 receive_seq=71850 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999691 adj=31999836 coil_temp=34.9 refs=0 mcu_temp=32.07 supply_voltage=3.014 sysload=0.30 cputime=3398.103 memavail=1411568 print_time=70770.950 buffer_time=3.916 print_stall=0 extruder: target=150 temp=150.9 pwm=0.068
Stats 70762.5: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000010 mcu_task_stddev=0.000016 bytes_write=590593 bytes_read=8074388 bytes_retransmit=9 bytes_invalid=0 send_seq=78199 receive_seq=78199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=419994 bytes_read=1295163 bytes_retransmit=0 bytes_invalid=0 send_seq=69966 receive_seq=69966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998485 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=452425 bytes_read=7733694 bytes_retransmit=9 bytes_invalid=0 send_seq=72029 receive_seq=72029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999587 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.650 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442460 bytes_read=24545416 bytes_retransmit=9 bytes_invalid=0 send_seq=71851 receive_seq=71851 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999690 adj=31999798 coil_temp=35.0 refs=0 mcu_temp=32.11 supply_voltage=3.014 sysload=0.30 cputime=3398.199 memavail=1411568 print_time=70770.950 buffer_time=2.916 print_stall=0 extruder: target=150 temp=149.6 pwm=0.322
RatOS:: Heating extruder to probing temperature...
RatOS | TEMPERATURE_WAIT:: Waiting for sensor: extruder, MINIMUM: 150, MAXIMUM: 155
RatOS:: please wait...
RatOS | TEMPERATURE_WAIT:: Temperature for toolhead T0 reached.
RatOS:: Beacon contact auto calibration...
Initial approach
Stats 70763.6: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000011 mcu_task_stddev=0.000022 bytes_write=595136 bytes_read=8075203 bytes_retransmit=9 bytes_invalid=0 send_seq=78286 receive_seq=78286 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=179999405 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420000 bytes_read=1295179 bytes_retransmit=0 bytes_invalid=0 send_seq=69967 receive_seq=69967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998324 adj=49998524 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=452487 bytes_read=7733853 bytes_retransmit=9 bytes_invalid=0 send_seq=72034 receive_seq=72034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999387 adj=63999681 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.5 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.607 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442466 bytes_read=24545788 bytes_retransmit=9 bytes_invalid=0 send_seq=71852 receive_seq=71852 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999690 adj=31999799 coil_temp=35.0 refs=0 mcu_temp=32.15 supply_voltage=3.014 sysload=0.30 cputime=3398.399 memavail=1411568 print_time=70771.849 buffer_time=2.792 print_stall=0 extruder: target=150 temp=151.6 pwm=0.000
Stats 70764.6: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000011 mcu_task_stddev=0.000022 bytes_write=595354 bytes_read=8075671 bytes_retransmit=9 bytes_invalid=0 send_seq=78301 receive_seq=78301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999399 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420006 bytes_read=1295195 bytes_retransmit=0 bytes_invalid=0 send_seq=69968 receive_seq=69968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998323 adj=49998540 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=452536 bytes_read=7734021 bytes_retransmit=9 bytes_invalid=0 send_seq=72038 receive_seq=72038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999386 adj=63999665 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.607 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442472 bytes_read=24546144 bytes_retransmit=9 bytes_invalid=0 send_seq=71853 receive_seq=71853 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999689 adj=31999778 coil_temp=35.1 refs=0 mcu_temp=32.19 supply_voltage=3.014 sysload=0.28 cputime=3398.443 memavail=1411336 print_time=70771.849 buffer_time=1.791 print_stall=0 extruder: target=150 temp=150.6 pwm=0.120
Stats 70765.6: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000011 mcu_task_stddev=0.000022 bytes_write=595556 bytes_read=8076108 bytes_retransmit=9 bytes_invalid=0 send_seq=78316 receive_seq=78316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420012 bytes_read=1295211 bytes_retransmit=0 bytes_invalid=0 send_seq=69969 receive_seq=69969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998321 adj=49998542 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=452612 bytes_read=7734195 bytes_retransmit=9 bytes_invalid=0 send_seq=72043 receive_seq=72043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999385 adj=63999677 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.607 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442478 bytes_read=24546500 bytes_retransmit=9 bytes_invalid=0 send_seq=71854 receive_seq=71854 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999689 adj=31999779 coil_temp=35.1 refs=0 mcu_temp=32.21 supply_voltage=3.014 sysload=0.28 cputime=3398.483 memavail=1411336 print_time=70771.849 buffer_time=0.791 print_stall=0 extruder: target=150 temp=149.6 pwm=0.337
toolhead: max_velocity: 800.000000
max_accel: 100.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70766.6: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000011 mcu_task_stddev=0.000022 bytes_write=596060 bytes_read=8076591 bytes_retransmit=9 bytes_invalid=0 send_seq=78341 receive_seq=78341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999383 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420018 bytes_read=1295240 bytes_retransmit=0 bytes_invalid=0 send_seq=69970 receive_seq=69970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998544 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452674 bytes_read=7734368 bytes_retransmit=9 bytes_invalid=0 send_seq=72048 receive_seq=72048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999684 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.607 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=442544 bytes_read=24546953 bytes_retransmit=9 bytes_invalid=0 send_seq=71861 receive_seq=71861 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999688 adj=31999783 coil_temp=35.1 refs=0 mcu_temp=32.24 supply_voltage=3.014 sysload=0.28 cputime=3398.533 memavail=1411112 print_time=70772.269 buffer_time=0.000 print_stall=0 extruder: target=150 temp=151.4 pwm=0.000
Stats 70767.6: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000011 mcu_task_stddev=0.000022 bytes_write=598279 bytes_read=8079443 bytes_retransmit=9 bytes_invalid=0 send_seq=78500 receive_seq=78500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999368 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420024 bytes_read=1295256 bytes_retransmit=0 bytes_invalid=0 send_seq=69971 receive_seq=69971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998548 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452729 bytes_read=7734552 bytes_retransmit=9 bytes_invalid=0 send_seq=72053 receive_seq=72053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999693 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.558 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=444014 bytes_read=24549641 bytes_retransmit=9 bytes_invalid=0 send_seq=71984 receive_seq=71984 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999688 adj=31999791 coil_temp=35.2 refs=0 mcu_temp=32.29 supply_voltage=3.014 sysload=0.28 cputime=3398.625 memavail=1411128 print_time=70773.269 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.8 pwm=0.098
Stats 70768.6: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000012 mcu_task_stddev=0.000018 bytes_write=600269 bytes_read=8082106 bytes_retransmit=9 bytes_invalid=0 send_seq=78644 receive_seq=78644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999361 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420030 bytes_read=1295272 bytes_retransmit=0 bytes_invalid=0 send_seq=69972 receive_seq=69972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998316 adj=49998574 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452811 bytes_read=7734731 bytes_retransmit=9 bytes_invalid=0 send_seq=72059 receive_seq=72059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999702 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.558 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=445296 bytes_read=24552059 bytes_retransmit=9 bytes_invalid=0 send_seq=72092 receive_seq=72092 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999687 adj=31999818 coil_temp=35.2 refs=0 mcu_temp=32.31 supply_voltage=3.014 sysload=0.28 cputime=3398.718 memavail=1411128 print_time=70774.094 buffer_time=0.033 print_stall=0 extruder: target=150 temp=149.8 pwm=0.265
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Collecting sample 1/3
Stats 70769.6: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000012 mcu_task_stddev=0.000018 bytes_write=600896 bytes_read=8082580 bytes_retransmit=9 bytes_invalid=0 send_seq=78666 receive_seq=78666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999364 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420036 bytes_read=1295288 bytes_retransmit=0 bytes_invalid=0 send_seq=69973 receive_seq=69973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998320 adj=49998579 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452873 bytes_read=7734890 bytes_retransmit=9 bytes_invalid=0 send_seq=72064 receive_seq=72064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999708 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.558 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=445314 bytes_read=24552455 bytes_retransmit=9 bytes_invalid=0 send_seq=72095 receive_seq=72095 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999687 adj=31999816 coil_temp=35.3 refs=0 mcu_temp=32.34 supply_voltage=3.014 sysload=0.26 cputime=3398.821 memavail=1411128 print_time=70775.635 buffer_time=0.574 print_stall=0 extruder: target=150 temp=151.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 100.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70770.6: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000012 mcu_task_stddev=0.000018 bytes_write=601679 bytes_read=8083421 bytes_retransmit=9 bytes_invalid=0 send_seq=78708 receive_seq=78708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999358 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420042 bytes_read=1295304 bytes_retransmit=0 bytes_invalid=0 send_seq=69974 receive_seq=69974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998321 adj=49998611 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452922 bytes_read=7735058 bytes_retransmit=9 bytes_invalid=0 send_seq=72068 receive_seq=72068 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999710 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.3 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.2 pwm=0.558 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=445562 bytes_read=24553216 bytes_retransmit=9 bytes_invalid=0 send_seq=72116 receive_seq=72116 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999686 adj=31999804 coil_temp=35.3 refs=0 mcu_temp=32.37 supply_voltage=3.014 sysload=0.26 cputime=3398.894 memavail=1411656 print_time=70776.230 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.4 pwm=0.172
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Collecting sample 2/3
Stats 70771.6: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000012 mcu_task_stddev=0.000018 bytes_write=603718 bytes_read=8085613 bytes_retransmit=9 bytes_invalid=0 send_seq=78831 receive_seq=78831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999363 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000010 bytes_write=420048 bytes_read=1295333 bytes_retransmit=0 bytes_invalid=0 send_seq=69975 receive_seq=69975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998649 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=452999 bytes_read=7735246 bytes_retransmit=9 bytes_invalid=0 send_seq=72073 receive_seq=72073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999727 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.5 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.533 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=446544 bytes_read=24555176 bytes_retransmit=9 bytes_invalid=0 send_seq=72200 receive_seq=72200 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999686 adj=31999813 coil_temp=35.3 refs=0 mcu_temp=32.40 supply_voltage=3.014 sysload=0.26 cputime=3398.983 memavail=1411656 print_time=70778.446 buffer_time=1.385 print_stall=0 extruder: target=150 temp=149.7 pwm=0.269
Stats 70772.6: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000012 mcu_task_stddev=0.000018 bytes_write=603920 bytes_read=8086052 bytes_retransmit=9 bytes_invalid=0 send_seq=78846 receive_seq=78846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999359 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000010 bytes_write=420054 bytes_read=1295349 bytes_retransmit=0 bytes_invalid=0 send_seq=69976 receive_seq=69976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998531 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=453061 bytes_read=7735405 bytes_retransmit=9 bytes_invalid=0 send_seq=72078 receive_seq=72078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999677 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.533 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=446550 bytes_read=24555532 bytes_retransmit=9 bytes_invalid=0 send_seq=72201 receive_seq=72201 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999685 adj=31999797 coil_temp=35.4 refs=0 mcu_temp=32.44 supply_voltage=3.014 sysload=0.26 cputime=3399.024 memavail=1411656 print_time=70778.446 buffer_time=0.384 print_stall=0 extruder: target=150 temp=151.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 100.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70773.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=605136 bytes_read=8087414 bytes_retransmit=9 bytes_invalid=0 send_seq=78919 receive_seq=78919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999353 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000010 bytes_write=420060 bytes_read=1295365 bytes_retransmit=0 bytes_invalid=0 send_seq=69977 receive_seq=69977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998319 adj=49998557 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=453110 bytes_read=7735573 bytes_retransmit=9 bytes_invalid=0 send_seq=72082 receive_seq=72082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999677 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.2 pwm=0.533 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=447108 bytes_read=24556775 bytes_retransmit=9 bytes_invalid=0 send_seq=72249 receive_seq=72249 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999686 adj=31999791 coil_temp=35.4 refs=0 mcu_temp=32.48 supply_voltage=3.014 sysload=0.26 cputime=3399.092 memavail=1411432 print_time=70779.239 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.4 pwm=0.166
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Collecting sample 3/3
Stats 70774.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=606731 bytes_read=8089115 bytes_retransmit=9 bytes_invalid=0 send_seq=79011 receive_seq=79011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999360 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000010 bytes_write=420066 bytes_read=1295381 bytes_retransmit=0 bytes_invalid=0 send_seq=69978 receive_seq=69978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998564 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=453192 bytes_read=7735752 bytes_retransmit=9 bytes_invalid=0 send_seq=72088 receive_seq=72088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999668 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.533 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=447802 bytes_read=24558251 bytes_retransmit=9 bytes_invalid=0 send_seq=72309 receive_seq=72309 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999685 adj=31999814 coil_temp=35.5 refs=0 mcu_temp=32.52 supply_voltage=3.014 sysload=0.24 cputime=3399.170 memavail=1410424 print_time=70781.255 buffer_time=1.192 print_stall=0 extruder: target=150 temp=149.7 pwm=0.260
Stats 70775.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=606933 bytes_read=8089554 bytes_retransmit=9 bytes_invalid=0 send_seq=79026 receive_seq=79026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999363 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000010 bytes_write=420072 bytes_read=1295397 bytes_retransmit=0 bytes_invalid=0 send_seq=69979 receive_seq=69979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998318 adj=49998486 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=453254 bytes_read=7735911 bytes_retransmit=9 bytes_invalid=0 send_seq=72093 receive_seq=72093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999627 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=36.5 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.2 pwm=0.533 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=447808 bytes_read=24558607 bytes_retransmit=9 bytes_invalid=0 send_seq=72310 receive_seq=72310 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999685 adj=31999785 coil_temp=35.5 refs=0 mcu_temp=32.59 supply_voltage=3.014 sysload=0.24 cputime=3399.258 memavail=1410424 print_time=70781.255 buffer_time=0.192 print_stall=0 extruder: target=150 temp=151.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 100.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70776.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=608576 bytes_read=8091409 bytes_retransmit=9 bytes_invalid=0 send_seq=79128 receive_seq=79128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999360 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420078 bytes_read=1295426 bytes_retransmit=0 bytes_invalid=0 send_seq=69980 receive_seq=69980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998323 adj=49998477 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453303 bytes_read=7736093 bytes_retransmit=9 bytes_invalid=0 send_seq=72097 receive_seq=72097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999608 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.5 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.505 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=448678 bytes_read=24560372 bytes_retransmit=9 bytes_invalid=0 send_seq=72384 receive_seq=72384 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999685 adj=31999775 coil_temp=35.6 refs=0 mcu_temp=32.64 supply_voltage=3.014 sysload=0.24 cputime=3399.442 memavail=1410424 print_time=70782.255 buffer_time=0.000 print_stall=0 extruder: target=150 temp=150.6 pwm=0.164
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Collected 3 samples, 0.0036 sd
Stats 70777.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=609798 bytes_read=8092620 bytes_retransmit=9 bytes_invalid=0 send_seq=79192 receive_seq=79192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999394 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420084 bytes_read=1295442 bytes_retransmit=0 bytes_invalid=0 send_seq=69981 receive_seq=69981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998326 adj=49998577 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453384 bytes_read=7736272 bytes_retransmit=9 bytes_invalid=0 send_seq=72103 receive_seq=72103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999622 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.505 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449084 bytes_read=24561392 bytes_retransmit=9 bytes_invalid=0 send_seq=72420 receive_seq=72420 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999684 adj=31999783 coil_temp=35.6 refs=0 mcu_temp=32.68 supply_voltage=3.014 sysload=0.24 cputime=3399.589 memavail=1410424 print_time=70784.086 buffer_time=1.022 print_stall=0 extruder: target=150 temp=150.3 pwm=0.153
Stats 70778.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=610000 bytes_read=8093075 bytes_retransmit=9 bytes_invalid=0 send_seq=79207 receive_seq=79207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999392 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420090 bytes_read=1295458 bytes_retransmit=0 bytes_invalid=0 send_seq=69982 receive_seq=69982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998442 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453433 bytes_read=7736426 bytes_retransmit=9 bytes_invalid=0 send_seq=72107 receive_seq=72107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999456 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.505 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449090 bytes_read=24561748 bytes_retransmit=9 bytes_invalid=0 send_seq=72421 receive_seq=72421 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999683 adj=31999677 coil_temp=35.7 refs=0 mcu_temp=32.73 supply_voltage=3.014 sysload=0.24 cputime=3399.682 memavail=1410424 print_time=70784.086 buffer_time=0.022 print_stall=0 extruder: target=150 temp=151.8 pwm=0.042
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 25.000000
RatOS | Adaptive Mesh:: Recieved coordinates X0=208.543 Y0=226.321 X1=278.699 Y1=273.68
RatOS | Adaptive Mesh:: mesh coordinates X0=208.543 Y0=226.321 X1=278.699 Y1=273.68
Stats 70779.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=612354 bytes_read=8093713 bytes_retransmit=9 bytes_invalid=0 send_seq=79256 receive_seq=79256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=179999421 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420102 bytes_read=1295490 bytes_retransmit=0 bytes_invalid=0 send_seq=69984 receive_seq=69984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998336 adj=49998502 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453482 bytes_read=7736594 bytes_retransmit=9 bytes_invalid=0 send_seq=72111 receive_seq=72111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999456 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.454 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449103 bytes_read=24562421 bytes_retransmit=9 bytes_invalid=0 send_seq=72423 receive_seq=72423 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999684 adj=31999674 coil_temp=35.7 refs=1 mcu_temp=32.78 supply_voltage=3.014 sysload=0.22 cputime=3399.903 memavail=1410424 print_time=70785.394 buffer_time=0.330 print_stall=0 extruder: target=150 temp=150.6 pwm=0.136
Stats 70780.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=621881 bytes_read=8094917 bytes_retransmit=9 bytes_invalid=0 send_seq=79424 receive_seq=79424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=1208 freq=179999419 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420108 bytes_read=1295506 bytes_retransmit=0 bytes_invalid=0 send_seq=69985 receive_seq=69985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998334 adj=49998477 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453532 bytes_read=7736763 bytes_retransmit=9 bytes_invalid=0 send_seq=72115 receive_seq=72115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999341 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.454 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449109 bytes_read=24565497 bytes_retransmit=9 bytes_invalid=0 send_seq=72424 receive_seq=72424 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999684 adj=31999652 coil_temp=35.7 refs=2 mcu_temp=32.82 supply_voltage=3.014 sysload=0.22 cputime=3400.270 memavail=1410424 print_time=70787.193 buffer_time=1.129 print_stall=0 extruder: target=150 temp=149.7 pwm=0.258
Stats 70781.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=623417 bytes_read=8095461 bytes_retransmit=9 bytes_invalid=0 send_seq=79460 receive_seq=79460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999425 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420114 bytes_read=1295535 bytes_retransmit=0 bytes_invalid=0 send_seq=69986 receive_seq=69986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998332 adj=49998463 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453594 bytes_read=7736936 bytes_retransmit=9 bytes_invalid=0 send_seq=72120 receive_seq=72120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999461 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.5 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.454 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449115 bytes_read=24568573 bytes_retransmit=9 bytes_invalid=0 send_seq=72425 receive_seq=72425 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999682 adj=31999709 coil_temp=35.8 refs=2 mcu_temp=32.87 supply_voltage=3.014 sysload=0.22 cputime=3400.457 memavail=1410424 print_time=70787.193 buffer_time=0.128 print_stall=0 extruder: target=150 temp=150.9 pwm=0.000
Sampled 1420 total points over 1 runs
Samples binned in 24 clusters
Mesh calibration complete
save_config: set [bed_mesh ratos] version = 1
save_config: set [bed_mesh ratos] points = 
  -0.059461, -0.058647, -0.050683, -0.047386, -0.045604, -0.042811
  -0.054921, -0.043836, -0.038546, -0.033845, -0.027556, -0.023409
  -0.060850, -0.053816, -0.041187, -0.042479, -0.036696, -0.031940
  -0.063874, -0.057791, -0.043342, -0.037216, -0.032253, -0.033494
save_config: set [bed_mesh ratos] x_count = 6
save_config: set [bed_mesh ratos] y_count = 4
save_config: set [bed_mesh ratos] mesh_x_pps = 2
save_config: set [bed_mesh ratos] mesh_y_pps = 2
save_config: set [bed_mesh ratos] algo = bicubic
save_config: set [bed_mesh ratos] tension = 0.2
save_config: set [bed_mesh ratos] min_x = 208.543
save_config: set [bed_mesh ratos] max_x = 278.699
save_config: set [bed_mesh ratos] min_y = 226.321
save_config: set [bed_mesh ratos] max_y = 273.68
Bed Mesh state has been saved to profile [ratos]
for the current session.  The SAVE_CONFIG command will
update the printer config file and restart the printer.
RatOS | Adaptive Mesh:: Probing the prime location..
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS | Adaptive Mesh:: Probing the start of the prime location at 470.0, 7.5
Stats 70782.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=628056 bytes_read=8096294 bytes_retransmit=9 bytes_invalid=0 send_seq=79548 receive_seq=79548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999420 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420120 bytes_read=1295551 bytes_retransmit=0 bytes_invalid=0 send_seq=69987 receive_seq=69987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49998403 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453638 bytes_read=7737099 bytes_retransmit=9 bytes_invalid=0 send_seq=72123 receive_seq=72123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999412 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.454 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449135 bytes_read=24571240 bytes_retransmit=9 bytes_invalid=0 send_seq=72428 receive_seq=72428 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999680 adj=31999661 coil_temp=35.8 refs=1 mcu_temp=32.93 supply_voltage=3.014 sysload=0.22 cputime=3400.689 memavail=1409172 print_time=70788.287 buffer_time=0.222 print_stall=0 extruder: target=150 temp=150.5 pwm=0.105
Stats 70783.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000016 mcu_task_stddev=0.000023 bytes_write=629429 bytes_read=8097889 bytes_retransmit=9 bytes_invalid=0 send_seq=79637 receive_seq=79637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999409 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420126 bytes_read=1295567 bytes_retransmit=0 bytes_invalid=0 send_seq=69988 receive_seq=69988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998329 adj=49998424 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453720 bytes_read=7737278 bytes_retransmit=9 bytes_invalid=0 send_seq=72129 receive_seq=72129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999476 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.435 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=449830 bytes_read=24575371 bytes_retransmit=9 bytes_invalid=0 send_seq=72486 receive_seq=72486 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999679 adj=31999688 coil_temp=36.0 refs=1 mcu_temp=32.98 supply_voltage=3.014 sysload=0.22 cputime=3400.880 memavail=1409172 print_time=70789.284 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.6 pwm=0.286
probe at 470.000,7.500 is z=0.097187
Result is z=0.097187
Last reading: 5397198.56Hz, 35.95C, -infmm
RatOS | Adaptive Mesh:: Saving offset adjustment of 0.09718749967976836 in probe_for_priming_result
RatOS | Adaptive Mesh:: Probing the end of the prime location at 470.0, 52.5
Stats 70784.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000016 mcu_task_stddev=0.000023 bytes_write=633724 bytes_read=8099422 bytes_retransmit=9 bytes_invalid=0 send_seq=79757 receive_seq=79757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999400 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420132 bytes_read=1295583 bytes_retransmit=0 bytes_invalid=0 send_seq=69989 receive_seq=69989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998327 adj=49998424 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453784 bytes_read=7737437 bytes_retransmit=9 bytes_invalid=0 send_seq=72134 receive_seq=72134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999510 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.435 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=450300 bytes_read=24579278 bytes_retransmit=9 bytes_invalid=0 send_seq=72529 receive_seq=72529 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999678 adj=31999701 coil_temp=35.9 refs=1 mcu_temp=33.02 supply_voltage=3.014 sysload=0.28 cputime=3401.094 memavail=1411984 print_time=70790.206 buffer_time=0.140 print_stall=0 extruder: target=150 temp=151.2 pwm=0.006
Resetting prediction variance 70785.470: freq=49998327 diff=-452058 stddev=2160.393
Stats 70785.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000016 mcu_task_stddev=0.000023 bytes_write=635389 bytes_read=8101424 bytes_retransmit=9 bytes_invalid=0 send_seq=79866 receive_seq=79866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420138 bytes_read=1295599 bytes_retransmit=0 bytes_invalid=0 send_seq=69990 receive_seq=69990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997817 adj=49998452 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453828 bytes_read=7737615 bytes_retransmit=9 bytes_invalid=0 send_seq=72137 receive_seq=72137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999377 adj=63999598 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.435 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451259 bytes_read=24583896 bytes_retransmit=9 bytes_invalid=0 send_seq=72609 receive_seq=72608 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999678 adj=31999727 coil_temp=36.0 refs=1 mcu_temp=33.05 supply_voltage=3.014 sysload=0.28 cputime=3401.371 memavail=1411748 print_time=70791.237 buffer_time=0.000 print_stall=0 extruder: target=150 temp=149.9 pwm=0.272
probe at 470.000,52.500 is z=0.056562
Result is z=0.056562
Last reading: 5399940.61Hz, 35.98C, -infmm
RatOS | Adaptive Mesh:: Saving offset adjustment of 0.0565624996801275 in probe_for_priming_end_result
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 25.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
bed_mesh fade complete: Current Z: 50.0000 fade_target: -0.0400 
RatOS:: Heating Extruder...
RatOS | TEMPERATURE_WAIT:: Waiting for sensor: extruder, MINIMUM: 220, MAXIMUM: 225
RatOS:: please wait...
Resetting prediction variance 70786.455: freq=49997817 diff=-887751 stddev=50000.000
Stats 70786.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000016 mcu_task_stddev=0.000023 bytes_write=643118 bytes_read=8102971 bytes_retransmit=9 bytes_invalid=0 send_seq=80028 receive_seq=80028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999383 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420144 bytes_read=1295628 bytes_retransmit=0 bytes_invalid=0 send_seq=69991 receive_seq=69991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996815 adj=49990549 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=453905 bytes_read=7737774 bytes_retransmit=9 bytes_invalid=0 send_seq=72142 receive_seq=72142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999643 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.435 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451542 bytes_read=24586035 bytes_retransmit=9 bytes_invalid=0 send_seq=72636 receive_seq=72636 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999677 adj=31999766 coil_temp=36.0 refs=0 mcu_temp=33.09 supply_voltage=3.014 sysload=0.28 cputime=3401.677 memavail=1411748 print_time=70796.077 buffer_time=3.987 print_stall=0 extruder: target=220 temp=149.6 pwm=1.000
Heater extruder approaching new target of 220.000
Resetting prediction variance 70787.440: freq=49996815 diff=-1234340 stddev=50000.000
Stats 70787.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000016 mcu_task_stddev=0.000023 bytes_write=643335 bytes_read=8103415 bytes_retransmit=9 bytes_invalid=0 send_seq=80044 receive_seq=80044 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999386 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420150 bytes_read=1295644 bytes_retransmit=0 bytes_invalid=0 send_seq=69992 receive_seq=69992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49995422 adj=49991375 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=453939 bytes_read=7737937 bytes_retransmit=9 bytes_invalid=0 send_seq=72145 receive_seq=72145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999641 Octopus_V1.1_F446: temp=34.3 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.403 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451548 bytes_read=24586391 bytes_retransmit=9 bytes_invalid=0 send_seq=72637 receive_seq=72637 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999676 adj=31999792 coil_temp=36.0 refs=0 mcu_temp=33.12 supply_voltage=3.014 sysload=0.28 cputime=3401.725 memavail=1411744 print_time=70796.077 buffer_time=2.986 print_stall=0 extruder: target=220 temp=154.7 pwm=1.000
Resetting prediction variance 70788.425: freq=49995422 diff=-1509226 stddev=50000.000
Stats 70788.6: gcodein=0  mcu: mcu_awake=0.031 mcu_task_avg=0.000019 mcu_task_stddev=0.000063 bytes_write=643567 bytes_read=8103910 bytes_retransmit=9 bytes_invalid=0 send_seq=80061 receive_seq=80061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999377 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420156 bytes_read=1295660 bytes_retransmit=0 bytes_invalid=0 send_seq=69993 receive_seq=69993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49993720 adj=49981418 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=453973 bytes_read=7738115 bytes_retransmit=9 bytes_invalid=0 send_seq=72148 receive_seq=72148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999615 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.390 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451554 bytes_read=24586747 bytes_retransmit=9 bytes_invalid=0 send_seq=72638 receive_seq=72638 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999674 adj=31999778 coil_temp=36.1 refs=0 mcu_temp=33.16 supply_voltage=3.014 sysload=0.28 cputime=3401.765 memavail=1411744 print_time=70796.077 buffer_time=1.985 print_stall=0 extruder: target=220 temp=163.7 pwm=1.000
Resetting prediction variance 70789.410: freq=49993720 diff=-1720031 stddev=50000.000
Stats 70789.6: gcodein=0  mcu: mcu_awake=0.031 mcu_task_avg=0.000019 mcu_task_stddev=0.000063 bytes_write=643769 bytes_read=8104347 bytes_retransmit=9 bytes_invalid=0 send_seq=80076 receive_seq=80076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999375 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420162 bytes_read=1295676 bytes_retransmit=0 bytes_invalid=0 send_seq=69994 receive_seq=69994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49991779 adj=49969438 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=454007 bytes_read=7738264 bytes_retransmit=9 bytes_invalid=0 send_seq=72151 receive_seq=72151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999376 adj=63999624 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=57.1 pwm=0.390 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451566 bytes_read=24587103 bytes_retransmit=9 bytes_invalid=0 send_seq=72640 receive_seq=72640 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999672 adj=31999779 coil_temp=36.0 refs=0 mcu_temp=33.19 supply_voltage=3.014 sysload=0.26 cputime=3401.805 memavail=1411744 print_time=70796.077 buffer_time=0.984 print_stall=0 extruder: target=220 temp=169.7 pwm=1.000
Resetting prediction variance 70790.395: freq=49991779 diff=-1876627 stddev=50000.000
Stats 70790.6: gcodein=0  mcu: mcu_awake=0.031 mcu_task_avg=0.000019 mcu_task_stddev=0.000063 bytes_write=644189 bytes_read=8104799 bytes_retransmit=9 bytes_invalid=0 send_seq=80095 receive_seq=80095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420168 bytes_read=1295691 bytes_retransmit=0 bytes_invalid=0 send_seq=69995 receive_seq=69995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49989661 adj=49955961 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=454057 bytes_read=7738418 bytes_retransmit=9 bytes_invalid=0 send_seq=72155 receive_seq=72155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999622 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=36.0 sd_pos=41100 heater_bed: target=55 temp=57.0 pwm=0.390 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451572 bytes_read=24587459 bytes_retransmit=9 bytes_invalid=0 send_seq=72641 receive_seq=72641 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999670 adj=31999763 coil_temp=36.0 refs=0 mcu_temp=33.20 supply_voltage=3.014 sysload=0.26 cputime=3401.846 memavail=1411744 print_time=70796.077 buffer_time=0.000 print_stall=0 extruder: target=220 temp=175.1 pwm=1.000
Resetting prediction variance 70791.379: freq=49989661 diff=-1984838 stddev=50000.000
Stats 70791.6: gcodein=0  mcu: mcu_awake=0.031 mcu_task_avg=0.000019 mcu_task_stddev=0.000063 bytes_write=644407 bytes_read=8105270 bytes_retransmit=9 bytes_invalid=0 send_seq=80111 receive_seq=80111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999371 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420174 bytes_read=1295705 bytes_retransmit=0 bytes_invalid=0 send_seq=69996 receive_seq=69996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49987422 adj=49941068 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=454091 bytes_read=7738596 bytes_retransmit=9 bytes_invalid=0 send_seq=72158 receive_seq=72158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999620 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.9 pwm=0.445 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451578 bytes_read=24587815 bytes_retransmit=9 bytes_invalid=0 send_seq=72642 receive_seq=72642 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999760 coil_temp=35.9 refs=0 mcu_temp=33.20 supply_voltage=3.014 sysload=0.26 cputime=3401.936 memavail=1411744 print_time=70796.878 buffer_time=0.000 print_stall=0 extruder: target=220 temp=181.8 pwm=1.000
Resetting prediction variance 70792.364: freq=49987422 diff=-2055970 stddev=50000.000
Stats 70792.6: gcodein=0  mcu: mcu_awake=0.031 mcu_task_avg=0.000019 mcu_task_stddev=0.000063 bytes_write=644624 bytes_read=8105714 bytes_retransmit=9 bytes_invalid=0 send_seq=80127 receive_seq=80127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999371 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=420180 bytes_read=1295733 bytes_retransmit=0 bytes_invalid=0 send_seq=69997 receive_seq=69997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49985102 adj=49924230 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454125 bytes_read=7738755 bytes_retransmit=9 bytes_invalid=0 send_seq=72161 receive_seq=72161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999617 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.9 pwm=0.392 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451584 bytes_read=24588171 bytes_retransmit=9 bytes_invalid=0 send_seq=72643 receive_seq=72643 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999670 adj=31999759 coil_temp=35.8 refs=0 mcu_temp=33.20 supply_voltage=3.014 sysload=0.26 cputime=3402.028 memavail=1411744 print_time=70797.878 buffer_time=0.000 print_stall=0 extruder: target=220 temp=186.9 pwm=1.000
Resetting prediction variance 70793.349: freq=49985102 diff=-2094124 stddev=50000.000
Stats 70793.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=644826 bytes_read=8106168 bytes_retransmit=9 bytes_invalid=0 send_seq=80142 receive_seq=80142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999378 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=420186 bytes_read=1295748 bytes_retransmit=0 bytes_invalid=0 send_seq=69998 receive_seq=69998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49982740 adj=49904885 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454159 bytes_read=7738896 bytes_retransmit=9 bytes_invalid=0 send_seq=72164 receive_seq=72164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999375 adj=63999616 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.8 pwm=0.392 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451590 bytes_read=24588527 bytes_retransmit=9 bytes_invalid=0 send_seq=72644 receive_seq=72644 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999670 adj=31999758 coil_temp=35.8 refs=0 mcu_temp=33.19 supply_voltage=3.014 sysload=0.26 cputime=3402.117 memavail=1411744 print_time=70798.879 buffer_time=0.000 print_stall=0 extruder: target=220 temp=191.5 pwm=1.000
Resetting prediction variance 70794.333: freq=49982740 diff=-2104114 stddev=50000.000
Stats 70794.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=645028 bytes_read=8106636 bytes_retransmit=9 bytes_invalid=0 send_seq=80157 receive_seq=80157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999381 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=420192 bytes_read=1295763 bytes_retransmit=0 bytes_invalid=0 send_seq=69999 receive_seq=69999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49980366 adj=49882661 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454193 bytes_read=7739065 bytes_retransmit=9 bytes_invalid=0 send_seq=72167 receive_seq=72167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999374 adj=63999600 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.8 pwm=0.392 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451596 bytes_read=24588883 bytes_retransmit=9 bytes_invalid=0 send_seq=72645 receive_seq=72645 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999747 coil_temp=35.7 refs=0 mcu_temp=33.18 supply_voltage=3.014 sysload=0.24 cputime=3402.211 memavail=1412788 print_time=70799.880 buffer_time=0.000 print_stall=0 extruder: target=220 temp=197.4 pwm=1.000
Resetting prediction variance 70795.317: freq=49980366 diff=-2091272 stddev=50000.000
Stats 70795.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=645230 bytes_read=8107075 bytes_retransmit=9 bytes_invalid=0 send_seq=80172 receive_seq=80172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999381 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=420198 bytes_read=1295778 bytes_retransmit=0 bytes_invalid=0 send_seq=70000 receive_seq=70000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49978006 adj=49856982 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454238 bytes_read=7739207 bytes_retransmit=9 bytes_invalid=0 send_seq=72170 receive_seq=72170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999586 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.8 pwm=0.392 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451602 bytes_read=24589239 bytes_retransmit=9 bytes_invalid=0 send_seq=72646 receive_seq=72646 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999743 coil_temp=35.7 refs=0 mcu_temp=33.14 supply_voltage=3.014 sysload=0.24 cputime=3402.305 memavail=1412636 print_time=70800.880 buffer_time=0.000 print_stall=0 extruder: target=220 temp=202.1 pwm=1.000
Resetting prediction variance 70796.302: freq=49978006 diff=-2057399 stddev=50000.000
Stats 70796.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=645432 bytes_read=8107514 bytes_retransmit=9 bytes_invalid=0 send_seq=80187 receive_seq=80187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999381 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=420204 bytes_read=1295794 bytes_retransmit=0 bytes_invalid=0 send_seq=70001 receive_seq=70001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49975685 adj=49826776 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454272 bytes_read=7739351 bytes_retransmit=9 bytes_invalid=0 send_seq=72173 receive_seq=72173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999373 adj=63999578 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.8 pwm=0.392 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451608 bytes_read=24589595 bytes_retransmit=9 bytes_invalid=0 send_seq=72647 receive_seq=72647 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999751 coil_temp=35.7 refs=0 mcu_temp=33.09 supply_voltage=3.014 sysload=0.24 cputime=3402.398 memavail=1412384 print_time=70801.881 buffer_time=0.000 print_stall=0 extruder: target=220 temp=206.4 pwm=1.000
Resetting prediction variance 70797.286: freq=49975685 diff=-2010599 stddev=50000.000
Stats 70797.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000008 mcu_task_stddev=0.000005 bytes_write=645649 bytes_read=8107987 bytes_retransmit=9 bytes_invalid=0 send_seq=80203 receive_seq=80203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999379 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000016 bytes_write=420210 bytes_read=1295823 bytes_retransmit=0 bytes_invalid=0 send_seq=70002 receive_seq=70002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49973417 adj=49792566 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454306 bytes_read=7739543 bytes_retransmit=9 bytes_invalid=0 send_seq=72176 receive_seq=72176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999373 adj=63999571 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.7 pwm=0.373 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451614 bytes_read=24589951 bytes_retransmit=9 bytes_invalid=0 send_seq=72648 receive_seq=72648 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999672 adj=31999757 coil_temp=35.6 refs=0 mcu_temp=33.05 supply_voltage=3.014 sysload=0.24 cputime=3402.495 memavail=1412132 print_time=70802.881 buffer_time=0.000 print_stall=0 extruder: target=220 temp=211.6 pwm=1.000
Resetting prediction variance 70798.270: freq=49973417 diff=-1952768 stddev=50000.000
Stats 70798.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=645851 bytes_read=8108441 bytes_retransmit=9 bytes_invalid=0 send_seq=80218 receive_seq=80218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999377 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000016 bytes_write=420216 bytes_read=1295839 bytes_retransmit=0 bytes_invalid=0 send_seq=70003 receive_seq=70003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49971213 adj=49803050 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454388 bytes_read=7739707 bytes_retransmit=9 bytes_invalid=0 send_seq=72182 receive_seq=72182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999372 adj=63999583 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.7 pwm=0.373 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451620 bytes_read=24590307 bytes_retransmit=9 bytes_invalid=0 send_seq=72649 receive_seq=72649 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999770 coil_temp=35.6 refs=0 mcu_temp=33.00 supply_voltage=3.014 sysload=0.24 cputime=3402.586 memavail=1412132 print_time=70803.882 buffer_time=0.000 print_stall=0 extruder: target=220 temp=215.7 pwm=0.569
Resetting prediction variance 70799.257: freq=49971213 diff=-1880899 stddev=50000.000
Stats 70799.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=646053 bytes_read=8108880 bytes_retransmit=9 bytes_invalid=0 send_seq=80233 receive_seq=80233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999375 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000016 bytes_write=420222 bytes_read=1295855 bytes_retransmit=0 bytes_invalid=0 send_seq=70004 receive_seq=70004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49969091 adj=49811316 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454454 bytes_read=7739866 bytes_retransmit=9 bytes_invalid=0 send_seq=72187 receive_seq=72187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999583 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.7 pwm=0.373 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451626 bytes_read=24590663 bytes_retransmit=9 bytes_invalid=0 send_seq=72650 receive_seq=72650 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999772 coil_temp=35.5 refs=0 mcu_temp=32.95 supply_voltage=3.014 sysload=0.22 cputime=3402.680 memavail=1412132 print_time=70804.883 buffer_time=0.000 print_stall=0 extruder: target=220 temp=218.7 pwm=0.319
Heater extruder within range of 220.000
Resetting prediction variance 70800.242: freq=49969091 diff=-1804400 stddev=50000.000
Stats 70800.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=646255 bytes_read=8109348 bytes_retransmit=9 bytes_invalid=0 send_seq=80248 receive_seq=80248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999370 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000016 bytes_write=420228 bytes_read=1295871 bytes_retransmit=0 bytes_invalid=0 send_seq=70005 receive_seq=70005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49967055 adj=49818252 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454520 bytes_read=7740054 bytes_retransmit=9 bytes_invalid=0 send_seq=72192 receive_seq=72192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999370 adj=63999582 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.373 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451632 bytes_read=24591019 bytes_retransmit=9 bytes_invalid=0 send_seq=72651 receive_seq=72651 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999673 adj=31999776 coil_temp=35.5 refs=0 mcu_temp=32.90 supply_voltage=3.014 sysload=0.22 cputime=3402.777 memavail=1412132 print_time=70805.883 buffer_time=0.000 print_stall=0 extruder: target=220 temp=218.7 pwm=0.709
Resetting prediction variance 70801.227: freq=49967055 diff=-1721829 stddev=50000.000
Stats 70801.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=646472 bytes_read=8109792 bytes_retransmit=9 bytes_invalid=0 send_seq=80264 receive_seq=80264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999366 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000016 bytes_write=420234 bytes_read=1295887 bytes_retransmit=0 bytes_invalid=0 send_seq=70006 receive_seq=70006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49965113 adj=49824242 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=454581 bytes_read=7740208 bytes_retransmit=9 bytes_invalid=0 send_seq=72196 receive_seq=72196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999592 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.366 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451638 bytes_read=24591375 bytes_retransmit=9 bytes_invalid=0 send_seq=72652 receive_seq=72652 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999674 adj=31999825 coil_temp=35.4 refs=0 mcu_temp=32.85 supply_voltage=3.014 sysload=0.22 cputime=3402.869 memavail=1412132 print_time=70806.883 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.9 pwm=0.498
Resetting prediction variance 70802.211: freq=49965113 diff=-1633007 stddev=50000.000
Stats 70802.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=646674 bytes_read=8110231 bytes_retransmit=9 bytes_invalid=0 send_seq=80279 receive_seq=80279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420240 bytes_read=1295916 bytes_retransmit=0 bytes_invalid=0 send_seq=70007 receive_seq=70007 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49963270 adj=49829669 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=454661 bytes_read=7740386 bytes_retransmit=9 bytes_invalid=0 send_seq=72202 receive_seq=72202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999618 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.366 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451644 bytes_read=24591731 bytes_retransmit=9 bytes_invalid=0 send_seq=72653 receive_seq=72653 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999674 adj=31999840 coil_temp=35.4 refs=0 mcu_temp=32.81 supply_voltage=3.014 sysload=0.22 cputime=3402.961 memavail=1411136 print_time=70807.884 buffer_time=0.000 print_stall=0 extruder: target=220 temp=221.8 pwm=0.129
RatOS | TEMPERATURE_WAIT:: Temperature for toolhead T0 reached.
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS | Priming:: Priming nozzle with prime blob..
RatOS | BEACON:: Nozzle expansion offset of 0.039156mm applied to T0
RatOS | Priming:: Lifting Z to 50.0..
RatOS | Priming:: Moving to 494.99999999999994, 5 along the edge of the print area..
RatOS | Priming:: Starting prime blob..
Resetting prediction variance 70803.354: freq=49963270 diff=-1547763 stddev=50000.000
Stats 70803.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=655710 bytes_read=8111434 bytes_retransmit=9 bytes_invalid=0 send_seq=80438 receive_seq=80438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=1621 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420246 bytes_read=1295932 bytes_retransmit=0 bytes_invalid=0 send_seq=70008 receive_seq=70008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49961515 adj=49834784 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=454721 bytes_read=7740569 bytes_retransmit=9 bytes_invalid=0 send_seq=72206 receive_seq=72206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999372 adj=63999601 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.6 pwm=0.313 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451650 bytes_read=24592087 bytes_retransmit=9 bytes_invalid=0 send_seq=72654 receive_seq=72654 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999672 adj=31999815 coil_temp=35.4 refs=0 mcu_temp=32.75 supply_voltage=3.014 sysload=0.22 cputime=3403.252 memavail=1411136 print_time=70813.663 buffer_time=4.562 print_stall=0 extruder: target=220 temp=220.7 pwm=0.448
Resetting prediction variance 70804.338: freq=49961515 diff=-1451613 stddev=50000.000
Stats 70804.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=657695 bytes_read=8112018 bytes_retransmit=9 bytes_invalid=0 send_seq=80482 receive_seq=80482 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999365 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420252 bytes_read=1295948 bytes_retransmit=0 bytes_invalid=0 send_seq=70009 receive_seq=70009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49959870 adj=49969626 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=454814 bytes_read=7740733 bytes_retransmit=9 bytes_invalid=0 send_seq=72212 receive_seq=72212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999607 Octopus_V1.1_F446: temp=34.1 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.5 pwm=0.368 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451656 bytes_read=24592443 bytes_retransmit=9 bytes_invalid=0 send_seq=72655 receive_seq=72655 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999671 adj=31999770 coil_temp=35.3 refs=0 mcu_temp=32.71 supply_voltage=3.014 sysload=0.20 cputime=3403.304 memavail=1402588 print_time=70813.663 buffer_time=3.560 print_stall=0 extruder: target=220 temp=220.0 pwm=0.542
Resetting prediction variance 70805.323: freq=49959870 diff=-1357221 stddev=50000.000
Stats 70805.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=657907 bytes_read=8112457 bytes_retransmit=9 bytes_invalid=0 send_seq=80497 receive_seq=80497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999361 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420258 bytes_read=1295964 bytes_retransmit=0 bytes_invalid=0 send_seq=70010 receive_seq=70010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49958333 adj=49959051 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=454895 bytes_read=7740897 bytes_retransmit=9 bytes_invalid=0 send_seq=72218 receive_seq=72218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999606 Octopus_V1.1_F446: temp=34.1 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.5 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451662 bytes_read=24592799 bytes_retransmit=9 bytes_invalid=0 send_seq=72656 receive_seq=72656 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999669 adj=31999772 coil_temp=35.3 refs=0 mcu_temp=32.67 supply_voltage=3.014 sysload=0.20 cputime=3403.345 memavail=1408128 print_time=70813.663 buffer_time=2.557 print_stall=0 extruder: target=220 temp=221.5 pwm=0.131
Resetting prediction variance 70806.307: freq=49958333 diff=-1261510 stddev=50000.000
Stats 70806.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=659113 bytes_read=8113005 bytes_retransmit=9 bytes_invalid=0 send_seq=80528 receive_seq=80528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999370 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420264 bytes_read=1295980 bytes_retransmit=0 bytes_invalid=0 send_seq=70011 receive_seq=70011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49956904 adj=49949300 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=455110 bytes_read=7741100 bytes_retransmit=9 bytes_invalid=0 send_seq=72226 receive_seq=72226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999368 adj=63999605 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.5 sd_pos=41100 heater_bed: target=55 temp=56.5 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451668 bytes_read=24593155 bytes_retransmit=9 bytes_invalid=0 send_seq=72657 receive_seq=72657 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999668 adj=31999764 coil_temp=35.2 refs=0 mcu_temp=32.63 supply_voltage=3.014 sysload=0.20 cputime=3403.396 memavail=1407880 print_time=70816.557 buffer_time=4.448 print_stall=0 extruder: target=220 temp=221.0 pwm=0.300
Resetting prediction variance 70807.291: freq=49956904 diff=-1166998 stddev=50000.000
Stats 70807.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000004 bytes_write=659315 bytes_read=8113444 bytes_retransmit=9 bytes_invalid=0 send_seq=80543 receive_seq=80543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999366 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420270 bytes_read=1296009 bytes_retransmit=0 bytes_invalid=0 send_seq=70012 receive_seq=70012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49955584 adj=49941940 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000013 bytes_write=455187 bytes_read=7741274 bytes_retransmit=9 bytes_invalid=0 send_seq=72231 receive_seq=72231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999572 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.4 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451674 bytes_read=24593511 bytes_retransmit=9 bytes_invalid=0 send_seq=72658 receive_seq=72658 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999747 coil_temp=35.2 refs=0 mcu_temp=32.61 supply_voltage=3.014 sysload=0.20 cputime=3403.437 memavail=1407884 print_time=70816.557 buffer_time=3.447 print_stall=0 extruder: target=220 temp=219.4 pwm=0.594
Resetting prediction variance 70808.276: freq=49955584 diff=-1069984 stddev=50000.000
Stats 70808.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000020 mcu_task_stddev=0.000036 bytes_write=659517 bytes_read=8113913 bytes_retransmit=9 bytes_invalid=0 send_seq=80558 receive_seq=80558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999364 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420276 bytes_read=1296025 bytes_retransmit=0 bytes_invalid=0 send_seq=70013 receive_seq=70013 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49954373 adj=49933274 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000013 bytes_write=455268 bytes_read=7741438 bytes_retransmit=9 bytes_invalid=0 send_seq=72237 receive_seq=72237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999595 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.3 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451680 bytes_read=24593867 bytes_retransmit=9 bytes_invalid=0 send_seq=72659 receive_seq=72659 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999743 coil_temp=35.2 refs=0 mcu_temp=32.58 supply_voltage=3.014 sysload=0.20 cputime=3403.507 memavail=1407888 print_time=70816.557 buffer_time=2.441 print_stall=0 extruder: target=220 temp=220.7 pwm=0.238
RatOS | Priming:: Bridging with 40% fan speed..
Resetting prediction variance 70809.261: freq=49954373 diff=-978197 stddev=50000.000
Stats 70809.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000020 mcu_task_stddev=0.000036 bytes_write=659734 bytes_read=8114372 bytes_retransmit=9 bytes_invalid=0 send_seq=80574 receive_seq=80574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999365 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420282 bytes_read=1296041 bytes_retransmit=0 bytes_invalid=0 send_seq=70014 receive_seq=70014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49953267 adj=49925435 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000013 bytes_write=455376 bytes_read=7741626 bytes_retransmit=9 bytes_invalid=0 send_seq=72242 receive_seq=72242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=63999370 adj=63999587 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.3 pwm=0.331 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451686 bytes_read=24594223 bytes_retransmit=9 bytes_invalid=0 send_seq=72660 receive_seq=72660 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999740 coil_temp=35.3 refs=0 mcu_temp=32.57 supply_voltage=3.014 sysload=0.18 cputime=3403.618 memavail=1407888 print_time=70819.359 buffer_time=4.241 print_stall=0 extruder: target=220 temp=221.4 pwm=0.143
Resetting prediction variance 70810.246: freq=49953267 diff=-889255 stddev=50000.000
Stats 70810.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000020 mcu_task_stddev=0.000036 bytes_write=659936 bytes_read=8114811 bytes_retransmit=9 bytes_invalid=0 send_seq=80589 receive_seq=80589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420288 bytes_read=1296057 bytes_retransmit=0 bytes_invalid=0 send_seq=70015 receive_seq=70015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49952262 adj=49924050 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000013 bytes_write=455477 bytes_read=7741785 bytes_retransmit=9 bytes_invalid=0 send_seq=72247 receive_seq=72247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999600 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=41100 heater_bed: target=55 temp=56.3 pwm=0.331 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451692 bytes_read=24594579 bytes_retransmit=9 bytes_invalid=0 send_seq=72661 receive_seq=72661 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999748 coil_temp=35.4 refs=0 mcu_temp=32.56 supply_voltage=3.014 sysload=0.18 cputime=3403.717 memavail=1407664 print_time=70819.359 buffer_time=3.239 print_stall=0 extruder: target=220 temp=219.0 pwm=0.679
Resetting prediction variance 70811.230: freq=49952262 diff=-801285 stddev=50000.000
Stats 70811.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000020 mcu_task_stddev=0.000036 bytes_write=660138 bytes_read=8115279 bytes_retransmit=9 bytes_invalid=0 send_seq=80604 receive_seq=80604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999373 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420294 bytes_read=1296073 bytes_retransmit=0 bytes_invalid=0 send_seq=70016 receive_seq=70016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49951356 adj=49917180 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000013 bytes_write=455543 bytes_read=7741944 bytes_retransmit=9 bytes_invalid=0 send_seq=72252 receive_seq=72252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999598 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=35.0 sd_pos=41100 heater_bed: target=55 temp=56.2 pwm=0.331 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451698 bytes_read=24594935 bytes_retransmit=9 bytes_invalid=0 send_seq=72662 receive_seq=72662 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999744 coil_temp=35.5 refs=0 mcu_temp=32.56 supply_voltage=3.014 sysload=0.18 cputime=3403.814 memavail=1407664 print_time=70819.359 buffer_time=2.234 print_stall=0 extruder: target=220 temp=220.0 pwm=0.354
Resetting prediction variance 70812.215: freq=49951356 diff=-717495 stddev=50000.000
Stats 70812.6: gcodein=0  mcu: mcu_awake=0.016 mcu_task_avg=0.000020 mcu_task_stddev=0.000036 bytes_write=660864 bytes_read=8115758 bytes_retransmit=9 bytes_invalid=0 send_seq=80627 receive_seq=80627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999373 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420300 bytes_read=1296102 bytes_retransmit=0 bytes_invalid=0 send_seq=70017 receive_seq=70017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49950546 adj=49911074 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=455768 bytes_read=7742157 bytes_retransmit=9 bytes_invalid=0 send_seq=72259 receive_seq=72259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=9 freq=63999371 adj=63999588 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.2 pwm=0.331 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451704 bytes_read=24595291 bytes_retransmit=9 bytes_invalid=0 send_seq=72663 receive_seq=72663 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999736 coil_temp=35.5 refs=0 mcu_temp=32.59 supply_voltage=3.014 sysload=0.18 cputime=3403.930 memavail=1407664 print_time=70822.307 buffer_time=4.182 print_stall=0 extruder: target=220 temp=222.2 pwm=0.000
Resetting prediction variance 70813.199: freq=49950546 diff=-636493 stddev=50000.000
Stats 70813.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=661081 bytes_read=8116213 bytes_retransmit=9 bytes_invalid=0 send_seq=80643 receive_seq=80643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999375 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420306 bytes_read=1296118 bytes_retransmit=0 bytes_invalid=0 send_seq=70018 receive_seq=70018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49949827 adj=49916230 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=455849 bytes_read=7742321 bytes_retransmit=9 bytes_invalid=0 send_seq=72265 receive_seq=72265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=9 freq=63999372 adj=63999591 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.2 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451710 bytes_read=24595647 bytes_retransmit=9 bytes_invalid=0 send_seq=72664 receive_seq=72664 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999748 coil_temp=35.6 refs=0 mcu_temp=32.62 supply_voltage=3.014 sysload=0.18 cputime=3404.030 memavail=1407440 print_time=70822.307 buffer_time=3.181 print_stall=0 extruder: target=220 temp=219.7 pwm=0.558
Resetting prediction variance 70814.184: freq=49949827 diff=-558406 stddev=50000.000
Stats 70814.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=661283 bytes_read=8116674 bytes_retransmit=9 bytes_invalid=0 send_seq=80658 receive_seq=80658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999374 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420312 bytes_read=1296134 bytes_retransmit=0 bytes_invalid=0 send_seq=70019 receive_seq=70019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49949196 adj=49911260 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=455929 bytes_read=7742485 bytes_retransmit=9 bytes_invalid=0 send_seq=72271 receive_seq=72271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999372 adj=63999596 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.1 sd_pos=41100 heater_bed: target=55 temp=56.1 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451716 bytes_read=24596003 bytes_retransmit=9 bytes_invalid=0 send_seq=72665 receive_seq=72665 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999666 adj=31999747 coil_temp=35.6 refs=0 mcu_temp=32.64 supply_voltage=3.014 sysload=0.17 cputime=3404.130 memavail=1405716 print_time=70822.307 buffer_time=2.181 print_stall=0 extruder: target=220 temp=219.5 pwm=0.490
Resetting prediction variance 70815.169: freq=49949196 diff=-483324 stddev=50000.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS | BEACON:: Nozzle expansion offset of 0.039156mm applied to T0
RatOS:: Printing...
extruder: pressure_advance: 0.020000
pressure_advance_smooth_time: 0.040000
Unknown command:"TIMELAPSE_TAKE_FRAME"
toolhead: max_velocity: 800.000000
max_accel: 2500.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70815.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=669167 bytes_read=8117742 bytes_retransmit=9 bytes_invalid=0 send_seq=80799 receive_seq=80799 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=2606 freq=179999380 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420318 bytes_read=1296150 bytes_retransmit=0 bytes_invalid=0 send_seq=70020 receive_seq=70020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948651 adj=49906963 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=456963 bytes_read=7742753 bytes_retransmit=9 bytes_invalid=0 send_seq=72292 receive_seq=72292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=0 freq=63999376 adj=63999592 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=34.1 sd_pos=41763 heater_bed: target=55 temp=56.0 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451722 bytes_read=24596359 bytes_retransmit=9 bytes_invalid=0 send_seq=72666 receive_seq=72666 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999665 adj=31999747 coil_temp=35.5 refs=0 mcu_temp=32.68 supply_voltage=3.014 sysload=0.17 cputime=3404.371 memavail=1405712 print_time=70824.354 buffer_time=3.228 print_stall=0 extruder: target=220 temp=222.5 pwm=0.000
Resetting prediction variance 70816.154: freq=49948651 diff=-411260 stddev=50000.000
Stats 70816.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=669643 bytes_read=8118196 bytes_retransmit=9 bytes_invalid=0 send_seq=80817 receive_seq=80817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2382 freq=179999384 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=420324 bytes_read=1296166 bytes_retransmit=0 bytes_invalid=0 send_seq=70021 receive_seq=70021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948187 adj=49902388 toolboard_t0: mcu_awake=0.004 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=457074 bytes_read=7742912 bytes_retransmit=9 bytes_invalid=0 send_seq=72297 receive_seq=72297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999375 adj=63999611 Octopus_V1.1_F446: temp=33.4 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.0 sd_pos=41763 heater_bed: target=55 temp=56.0 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451728 bytes_read=24596715 bytes_retransmit=9 bytes_invalid=0 send_seq=72667 receive_seq=72667 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999664 adj=31999734 coil_temp=35.5 refs=0 mcu_temp=32.72 supply_voltage=3.014 sysload=0.17 cputime=3404.414 memavail=1405716 print_time=70824.354 buffer_time=2.228 print_stall=0 extruder: target=220 temp=220.1 pwm=0.453
Stats 70817.6: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000007 mcu_task_stddev=0.000005 bytes_write=672027 bytes_read=8118834 bytes_retransmit=9 bytes_invalid=0 send_seq=80866 receive_seq=80866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=1678 freq=179999387 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=420330 bytes_read=1296195 bytes_retransmit=0 bytes_invalid=0 send_seq=70022 receive_seq=70022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49898553 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000023 mcu_task_stddev=0.000028 bytes_write=457298 bytes_read=7743091 bytes_retransmit=9 bytes_invalid=0 send_seq=72303 receive_seq=72303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=63999375 adj=63999590 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.0 sd_pos=42193 heater_bed: target=55 temp=56.1 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451734 bytes_read=24597071 bytes_retransmit=9 bytes_invalid=0 send_seq=72668 receive_seq=72668 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999715 coil_temp=35.5 refs=0 mcu_temp=32.77 supply_voltage=3.014 sysload=0.17 cputime=3404.470 memavail=1405716 print_time=70825.392 buffer_time=2.263 print_stall=0 extruder: target=220 temp=218.7 pwm=0.692
Stats 70818.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=675629 bytes_read=8119564 bytes_retransmit=9 bytes_invalid=0 send_seq=80936 receive_seq=80936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=420336 bytes_read=1296211 bytes_retransmit=0 bytes_invalid=0 send_seq=70023 receive_seq=70023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49897698 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000023 mcu_task_stddev=0.000028 bytes_write=457411 bytes_read=7743284 bytes_retransmit=9 bytes_invalid=0 send_seq=72309 receive_seq=72309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=63999372 adj=63999580 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=42796 heater_bed: target=55 temp=55.9 pwm=0.300 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451740 bytes_read=24597427 bytes_retransmit=9 bytes_invalid=0 send_seq=72669 receive_seq=72669 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999661 adj=31999694 coil_temp=35.5 refs=0 mcu_temp=32.80 supply_voltage=3.014 sysload=0.17 cputime=3404.529 memavail=1405716 print_time=70826.184 buffer_time=2.056 print_stall=0 extruder: target=220 temp=222.0 pwm=0.038
Stats 70819.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=677019 bytes_read=8120093 bytes_retransmit=9 bytes_invalid=0 send_seq=80969 receive_seq=80969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=420342 bytes_read=1296227 bytes_retransmit=0 bytes_invalid=0 send_seq=70024 receive_seq=70024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49897668 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000023 mcu_task_stddev=0.000028 bytes_write=457508 bytes_read=7743438 bytes_retransmit=9 bytes_invalid=0 send_seq=72313 receive_seq=72313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999372 adj=63999517 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.0 sd_pos=43200 heater_bed: target=55 temp=55.9 pwm=0.300 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451746 bytes_read=24597783 bytes_retransmit=9 bytes_invalid=0 send_seq=72670 receive_seq=72670 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999659 adj=31999662 coil_temp=35.6 refs=0 mcu_temp=32.83 supply_voltage=3.014 sysload=0.23 cputime=3404.580 memavail=1405724 print_time=70827.260 buffer_time=2.131 print_stall=0 extruder: target=220 temp=221.3 pwm=0.177
Stats 70820.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=679250 bytes_read=8120721 bytes_retransmit=9 bytes_invalid=0 send_seq=81016 receive_seq=81016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=179999385 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=420348 bytes_read=1296243 bytes_retransmit=0 bytes_invalid=0 send_seq=70025 receive_seq=70025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49897688 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000023 mcu_task_stddev=0.000028 bytes_write=457794 bytes_read=7743612 bytes_retransmit=9 bytes_invalid=0 send_seq=72321 receive_seq=72321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=0 freq=63999370 adj=63999540 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=34.6 sd_pos=43927 heater_bed: target=55 temp=55.9 pwm=0.300 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451752 bytes_read=24598139 bytes_retransmit=9 bytes_invalid=0 send_seq=72671 receive_seq=72671 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999658 adj=31999659 coil_temp=35.8 refs=0 mcu_temp=32.87 supply_voltage=3.014 sysload=0.23 cputime=3404.649 memavail=1405724 print_time=70828.303 buffer_time=2.173 print_stall=0 extruder: target=220 temp=219.1 pwm=0.626
Stats 70821.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=680619 bytes_read=8121250 bytes_retransmit=9 bytes_invalid=0 send_seq=81049 receive_seq=81049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000018 bytes_write=420354 bytes_read=1296259 bytes_retransmit=0 bytes_invalid=0 send_seq=70026 receive_seq=70026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49906765 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000023 mcu_task_stddev=0.000028 bytes_write=457983 bytes_read=7743805 bytes_retransmit=9 bytes_invalid=0 send_seq=72327 receive_seq=72327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999548 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=36.0 sd_pos=44300 heater_bed: target=55 temp=55.8 pwm=0.300 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451758 bytes_read=24598495 bytes_retransmit=9 bytes_invalid=0 send_seq=72672 receive_seq=72672 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999658 adj=31999673 coil_temp=36.1 refs=0 mcu_temp=32.93 supply_voltage=3.014 sysload=0.23 cputime=3404.760 memavail=1401136 print_time=70829.277 buffer_time=2.145 print_stall=0 extruder: target=220 temp=221.2 pwm=0.041
Stats 70822.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=682709 bytes_read=8121834 bytes_retransmit=9 bytes_invalid=0 send_seq=81093 receive_seq=81093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=20 upcoming_bytes=0 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420360 bytes_read=1296288 bytes_retransmit=0 bytes_invalid=0 send_seq=70027 receive_seq=70027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49913736 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=458078 bytes_read=7743974 bytes_retransmit=9 bytes_invalid=0 send_seq=72331 receive_seq=72331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=63999368 adj=63999509 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.5 sd_pos=45048 heater_bed: target=55 temp=55.8 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451764 bytes_read=24598851 bytes_retransmit=9 bytes_invalid=0 send_seq=72673 receive_seq=72673 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999657 adj=31999675 coil_temp=36.2 refs=0 mcu_temp=32.99 supply_voltage=3.014 sysload=0.23 cputime=3404.817 memavail=1406756 print_time=70830.334 buffer_time=2.202 print_stall=0 extruder: target=220 temp=221.6 pwm=0.041
Stats 70823.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=684304 bytes_read=8122427 bytes_retransmit=9 bytes_invalid=0 send_seq=81130 receive_seq=81130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420366 bytes_read=1296304 bytes_retransmit=0 bytes_invalid=0 send_seq=70028 receive_seq=70028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49921248 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=458200 bytes_read=7744152 bytes_retransmit=9 bytes_invalid=0 send_seq=72337 receive_seq=72337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=63999369 adj=63999498 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.5 sd_pos=45535 heater_bed: target=55 temp=55.7 pwm=0.316 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451770 bytes_read=24599207 bytes_retransmit=9 bytes_invalid=0 send_seq=72674 receive_seq=72674 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999656 adj=31999678 coil_temp=36.3 refs=0 mcu_temp=33.05 supply_voltage=3.014 sysload=0.23 cputime=3404.868 memavail=1406756 print_time=70831.408 buffer_time=2.276 print_stall=0 extruder: target=220 temp=219.3 pwm=0.609
Stats 70824.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=687004 bytes_read=8123071 bytes_retransmit=9 bytes_invalid=0 send_seq=81186 receive_seq=81186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420372 bytes_read=1296320 bytes_retransmit=0 bytes_invalid=0 send_seq=70029 receive_seq=70029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49927231 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=458638 bytes_read=7744351 bytes_retransmit=9 bytes_invalid=0 send_seq=72347 receive_seq=72347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=63999370 adj=63999531 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=35.0 sd_pos=46263 heater_bed: target=55 temp=55.8 pwm=0.304 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451776 bytes_read=24599563 bytes_retransmit=9 bytes_invalid=0 send_seq=72675 receive_seq=72675 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999655 adj=31999685 coil_temp=36.4 refs=0 mcu_temp=33.14 supply_voltage=3.014 sysload=0.22 cputime=3404.924 memavail=1406292 print_time=70832.293 buffer_time=2.160 print_stall=0 extruder: target=220 temp=220.6 pwm=0.171
Stats 70825.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=691053 bytes_read=8123820 bytes_retransmit=9 bytes_invalid=0 send_seq=81263 receive_seq=81263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420378 bytes_read=1296336 bytes_retransmit=0 bytes_invalid=0 send_seq=70030 receive_seq=70030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49929549 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=458955 bytes_read=7744525 bytes_retransmit=9 bytes_invalid=0 send_seq=72355 receive_seq=72355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=0 freq=63999368 adj=63999550 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=33.6 sd_pos=47757 heater_bed: target=55 temp=55.8 pwm=0.304 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451782 bytes_read=24599919 bytes_retransmit=9 bytes_invalid=0 send_seq=72676 receive_seq=72676 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999653 adj=31999678 coil_temp=36.5 refs=0 mcu_temp=33.22 supply_voltage=3.014 sysload=0.22 cputime=3404.988 memavail=1406292 print_time=70833.269 buffer_time=2.135 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Stats 70826.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=694785 bytes_read=8124563 bytes_retransmit=9 bytes_invalid=0 send_seq=81333 receive_seq=81333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=0 freq=179999387 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420384 bytes_read=1296352 bytes_retransmit=0 bytes_invalid=0 send_seq=70031 receive_seq=70031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49932779 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=459324 bytes_read=7744718 bytes_retransmit=9 bytes_invalid=0 send_seq=72364 receive_seq=72364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=63999367 adj=63999560 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=35.5 sd_pos=49378 heater_bed: target=55 temp=55.7 pwm=0.304 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451788 bytes_read=24600275 bytes_retransmit=9 bytes_invalid=0 send_seq=72677 receive_seq=72677 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999652 adj=31999688 coil_temp=36.6 refs=0 mcu_temp=33.30 supply_voltage=3.014 sysload=0.22 cputime=3405.063 memavail=1406388 print_time=70834.476 buffer_time=2.341 print_stall=0 extruder: target=220 temp=219.4 pwm=0.605
Stats 70827.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000013 mcu_task_stddev=0.000013 bytes_write=697619 bytes_read=8125223 bytes_retransmit=9 bytes_invalid=0 send_seq=81390 receive_seq=81390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999395 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420390 bytes_read=1296381 bytes_retransmit=0 bytes_invalid=0 send_seq=70032 receive_seq=70032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49948095 adj=49937337 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000023 bytes_write=459473 bytes_read=7744923 bytes_retransmit=9 bytes_invalid=0 send_seq=72370 receive_seq=72370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999366 adj=63999559 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6 sd_pos=51015 heater_bed: target=55 temp=55.7 pwm=0.304 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451794 bytes_read=24600631 bytes_retransmit=9 bytes_invalid=0 send_seq=72678 receive_seq=72678 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999652 adj=31999701 coil_temp=36.8 refs=0 mcu_temp=33.39 supply_voltage=3.014 sysload=0.22 cputime=3405.202 memavail=1406388 print_time=70835.261 buffer_time=2.125 print_stall=0 extruder: target=220 temp=220.0 pwm=0.331
Resetting prediction variance 70827.968: freq=49948095 diff=3845159 stddev=51270.401
Stats 70828.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000012 mcu_task_stddev=0.000010 bytes_write=702007 bytes_read=8126013 bytes_retransmit=9 bytes_invalid=0 send_seq=81472 receive_seq=81472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999393 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420396 bytes_read=1296397 bytes_retransmit=0 bytes_invalid=0 send_seq=70033 receive_seq=70033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49953728 adj=49937818 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000023 bytes_write=459844 bytes_read=7745102 bytes_retransmit=9 bytes_invalid=0 send_seq=72379 receive_seq=72379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999372 adj=63999519 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=33.6 sd_pos=52716 heater_bed: target=55 temp=55.6 pwm=0.304 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451800 bytes_read=24600987 bytes_retransmit=9 bytes_invalid=0 send_seq=72679 receive_seq=72679 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999652 adj=31999691 coil_temp=36.9 refs=0 mcu_temp=33.48 supply_voltage=3.014 sysload=0.22 cputime=3405.352 memavail=1406388 print_time=70836.308 buffer_time=2.171 print_stall=0 extruder: target=220 temp=221.8 pwm=0.000
Resetting prediction variance 70828.953: freq=49953728 diff=3685403 stddev=50000.000
Stats 70829.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000012 mcu_task_stddev=0.000010 bytes_write=706018 bytes_read=8126786 bytes_retransmit=9 bytes_invalid=0 send_seq=81548 receive_seq=81548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=292 freq=179999410 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420402 bytes_read=1296413 bytes_retransmit=0 bytes_invalid=0 send_seq=70034 receive_seq=70034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49958957 adj=50011868 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000023 bytes_write=460239 bytes_read=7745300 bytes_retransmit=9 bytes_invalid=0 send_seq=72389 receive_seq=72389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999373 adj=63999616 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.5 sd_pos=54437 heater_bed: target=55 temp=55.6 pwm=0.287 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451806 bytes_read=24601343 bytes_retransmit=9 bytes_invalid=0 send_seq=72680 receive_seq=72680 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999652 adj=31999709 coil_temp=37.0 refs=0 mcu_temp=33.55 supply_voltage=3.014 sysload=0.20 cputime=3405.502 memavail=1406148 print_time=70837.566 buffer_time=2.429 print_stall=0 extruder: target=220 temp=220.1 pwm=0.411
Resetting prediction variance 70829.937: freq=49958957 diff=3534221 stddev=50000.000
Stats 70830.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000012 mcu_task_stddev=0.000010 bytes_write=709678 bytes_read=8127485 bytes_retransmit=9 bytes_invalid=0 send_seq=81615 receive_seq=81615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=179999417 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420408 bytes_read=1296429 bytes_retransmit=0 bytes_invalid=0 send_seq=70035 receive_seq=70035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49963828 adj=50054374 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000023 bytes_write=460417 bytes_read=7745479 bytes_retransmit=9 bytes_invalid=0 send_seq=72395 receive_seq=72395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999551 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=34.1 sd_pos=56014 heater_bed: target=55 temp=55.6 pwm=0.287 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451812 bytes_read=24601699 bytes_retransmit=9 bytes_invalid=0 send_seq=72681 receive_seq=72681 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999653 adj=31999691 coil_temp=37.1 refs=0 mcu_temp=33.67 supply_voltage=3.014 sysload=0.20 cputime=3405.645 memavail=1406148 print_time=70838.436 buffer_time=2.297 print_stall=0 extruder: target=220 temp=219.0 pwm=0.594
Resetting prediction variance 70830.922: freq=49963828 diff=3385223 stddev=50000.000
Stats 70831.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000012 mcu_task_stddev=0.000010 bytes_write=713465 bytes_read=8128214 bytes_retransmit=9 bytes_invalid=0 send_seq=81688 receive_seq=81688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=179999413 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=420414 bytes_read=1296445 bytes_retransmit=0 bytes_invalid=0 send_seq=70036 receive_seq=70036 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49968368 adj=50105156 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000023 bytes_write=460827 bytes_read=7745668 bytes_retransmit=9 bytes_invalid=0 send_seq=72406 receive_seq=72406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=63999374 adj=63999537 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.2 raspberry_pi: temp=35.0 sd_pos=57697 heater_bed: target=55 temp=55.5 pwm=0.287 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451818 bytes_read=24602055 bytes_retransmit=9 bytes_invalid=0 send_seq=72682 receive_seq=72682 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999655 adj=31999687 coil_temp=37.1 refs=0 mcu_temp=33.75 supply_voltage=3.014 sysload=0.20 cputime=3405.796 memavail=1406148 print_time=70839.333 buffer_time=2.195 print_stall=0 extruder: target=220 temp=221.1 pwm=0.056
Resetting prediction variance 70831.906: freq=49968368 diff=3234693 stddev=50000.000
Stats 70832.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000012 mcu_task_stddev=0.000010 bytes_write=717438 bytes_read=8128982 bytes_retransmit=9 bytes_invalid=0 send_seq=81763 receive_seq=81763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=248 freq=179999410 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000028 bytes_write=420420 bytes_read=1296474 bytes_retransmit=0 bytes_invalid=0 send_seq=70037 receive_seq=70037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49972598 adj=50147015 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=461233 bytes_read=7745896 bytes_retransmit=9 bytes_invalid=0 send_seq=72417 receive_seq=72417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999560 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=34.6 sd_pos=59220 heater_bed: target=55 temp=55.5 pwm=0.287 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451824 bytes_read=24602411 bytes_retransmit=9 bytes_invalid=0 send_seq=72683 receive_seq=72683 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999655 adj=31999736 coil_temp=37.3 refs=0 mcu_temp=33.83 supply_voltage=3.014 sysload=0.20 cputime=3405.949 memavail=1406148 print_time=70840.545 buffer_time=2.406 print_stall=0 extruder: target=220 temp=220.5 pwm=0.291
Resetting prediction variance 70832.891: freq=49972598 diff=3092873 stddev=50000.000
Stats 70833.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=720989 bytes_read=8129697 bytes_retransmit=9 bytes_invalid=0 send_seq=81830 receive_seq=81830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=179999412 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000028 bytes_write=420426 bytes_read=1296490 bytes_retransmit=0 bytes_invalid=0 send_seq=70038 receive_seq=70038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49976550 adj=50145765 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=461542 bytes_read=7746090 bytes_retransmit=9 bytes_invalid=0 send_seq=72426 receive_seq=72426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999574 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.6 sd_pos=60550 heater_bed: target=55 temp=55.5 pwm=0.297 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451830 bytes_read=24602767 bytes_retransmit=9 bytes_invalid=0 send_seq=72684 receive_seq=72684 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999655 adj=31999742 coil_temp=37.4 refs=0 mcu_temp=33.91 supply_voltage=3.014 sysload=0.20 cputime=3406.096 memavail=1406148 print_time=70841.452 buffer_time=2.312 print_stall=0 extruder: target=220 temp=218.7 pwm=0.653
Resetting prediction variance 70833.875: freq=49976550 diff=2951119 stddev=50000.000
Stats 70834.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=725042 bytes_read=8130451 bytes_retransmit=9 bytes_invalid=0 send_seq=81908 receive_seq=81908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=179999412 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000028 bytes_write=420432 bytes_read=1296506 bytes_retransmit=0 bytes_invalid=0 send_seq=70039 receive_seq=70039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49980239 adj=50174595 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=461944 bytes_read=7746274 bytes_retransmit=9 bytes_invalid=0 send_seq=72436 receive_seq=72436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=63999377 adj=63999613 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.1 sd_pos=61868 heater_bed: target=55 temp=55.4 pwm=0.351 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451836 bytes_read=24603123 bytes_retransmit=9 bytes_invalid=0 send_seq=72685 receive_seq=72685 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999654 adj=31999741 coil_temp=37.5 refs=0 mcu_temp=33.98 supply_voltage=3.014 sysload=0.26 cputime=3406.230 memavail=1407164 print_time=70842.317 buffer_time=2.176 print_stall=0 extruder: target=220 temp=220.9 pwm=0.100
Resetting prediction variance 70834.860: freq=49980239 diff=2816853 stddev=50000.000
Stats 70835.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=728764 bytes_read=8131199 bytes_retransmit=9 bytes_invalid=0 send_seq=81979 receive_seq=81979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=128 freq=179999432 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000028 bytes_write=420438 bytes_read=1296522 bytes_retransmit=0 bytes_invalid=0 send_seq=70040 receive_seq=70040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49983690 adj=50203981 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=462402 bytes_read=7746472 bytes_retransmit=9 bytes_invalid=0 send_seq=72446 receive_seq=72446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999601 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=34.1 sd_pos=63202 heater_bed: target=55 temp=55.4 pwm=0.298 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451842 bytes_read=24603479 bytes_retransmit=9 bytes_invalid=0 send_seq=72686 receive_seq=72686 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999653 adj=31999732 coil_temp=37.6 refs=0 mcu_temp=34.05 supply_voltage=3.014 sysload=0.26 cputime=3406.383 memavail=1406940 print_time=70843.478 buffer_time=2.336 print_stall=0 extruder: target=220 temp=221.2 pwm=0.112
Resetting prediction variance 70835.845: freq=49983690 diff=2684860 stddev=50000.000
Stats 70836.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=731811 bytes_read=8131858 bytes_retransmit=9 bytes_invalid=0 send_seq=82038 receive_seq=82038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999426 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000028 bytes_write=420444 bytes_read=1296538 bytes_retransmit=0 bytes_invalid=0 send_seq=70041 receive_seq=70041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49986919 adj=50186845 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=462721 bytes_read=7746666 bytes_retransmit=9 bytes_invalid=0 send_seq=72455 receive_seq=72455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999552 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.6 sd_pos=64532 heater_bed: target=55 temp=55.4 pwm=0.298 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451848 bytes_read=24603835 bytes_retransmit=9 bytes_invalid=0 send_seq=72687 receive_seq=72687 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999653 adj=31999685 coil_temp=37.7 refs=0 mcu_temp=34.12 supply_voltage=3.014 sysload=0.26 cputime=3406.530 memavail=1406728 print_time=70844.289 buffer_time=2.147 print_stall=0 extruder: target=220 temp=218.4 pwm=0.757
Resetting prediction variance 70836.829: freq=49986919 diff=2558067 stddev=50000.000
Stats 70837.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=736652 bytes_read=8132667 bytes_retransmit=9 bytes_invalid=0 send_seq=82128 receive_seq=82128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=201 freq=179999419 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420450 bytes_read=1296567 bytes_retransmit=0 bytes_invalid=0 send_seq=70042 receive_seq=70042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49989941 adj=50217284 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=463222 bytes_read=7746870 bytes_retransmit=9 bytes_invalid=0 send_seq=72466 receive_seq=72466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=0 freq=63999384 adj=63999579 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=35.0 sd_pos=66498 heater_bed: target=55 temp=55.3 pwm=0.298 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451854 bytes_read=24604191 bytes_retransmit=9 bytes_invalid=0 send_seq=72688 receive_seq=72688 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999652 adj=31999703 coil_temp=37.8 refs=0 mcu_temp=34.23 supply_voltage=3.014 sysload=0.26 cputime=3406.702 memavail=1406728 print_time=70845.649 buffer_time=2.507 print_stall=0 extruder: target=220 temp=220.2 pwm=0.254
Resetting prediction variance 70837.813: freq=49989941 diff=2435451 stddev=50000.000
Stats 70838.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=739404 bytes_read=8133349 bytes_retransmit=9 bytes_invalid=0 send_seq=82184 receive_seq=82184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999413 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420456 bytes_read=1296583 bytes_retransmit=0 bytes_invalid=0 send_seq=70043 receive_seq=70043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49992772 adj=50169756 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=463567 bytes_read=7747063 bytes_retransmit=9 bytes_invalid=0 send_seq=72475 receive_seq=72475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999389 adj=63999648 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.6 sd_pos=67185 heater_bed: target=55 temp=55.4 pwm=0.298 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451860 bytes_read=24604547 bytes_retransmit=9 bytes_invalid=0 send_seq=72689 receive_seq=72689 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999651 adj=31999731 coil_temp=37.8 refs=0 mcu_temp=34.31 supply_voltage=3.014 sysload=0.26 cputime=3406.819 memavail=1405972 print_time=70846.236 buffer_time=2.093 print_stall=0 extruder: target=220 temp=222.1 pwm=0.000
Resetting prediction variance 70838.797: freq=49992772 diff=2314770 stddev=50000.000
Stats 70839.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=744980 bytes_read=8134223 bytes_retransmit=9 bytes_invalid=0 send_seq=82286 receive_seq=82286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=8793 freq=179999403 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420462 bytes_read=1296599 bytes_retransmit=0 bytes_invalid=0 send_seq=70044 receive_seq=70044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49995423 adj=50206005 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=465932 bytes_read=7747422 bytes_retransmit=9 bytes_invalid=0 send_seq=72517 receive_seq=72517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=63999386 adj=63999738 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.0 sd_pos=70269 heater_bed: target=55 temp=55.2 pwm=0.357 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451866 bytes_read=24604903 bytes_retransmit=9 bytes_invalid=0 send_seq=72690 receive_seq=72690 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999650 adj=31999731 coil_temp=37.9 refs=0 mcu_temp=34.38 supply_voltage=3.014 sysload=0.24 cputime=3406.932 memavail=1407520 print_time=70848.457 buffer_time=3.313 print_stall=0 extruder: target=220 temp=218.7 pwm=0.766
Resetting prediction variance 70839.782: freq=49995423 diff=2199895 stddev=50000.000
Stats 70840.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=748155 bytes_read=8134907 bytes_retransmit=9 bytes_invalid=0 send_seq=82350 receive_seq=82350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6091 freq=179999393 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420468 bytes_read=1296615 bytes_retransmit=0 bytes_invalid=0 send_seq=70045 receive_seq=70045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997907 adj=50106502 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=466030 bytes_read=7747581 bytes_retransmit=9 bytes_invalid=0 send_seq=72522 receive_seq=72522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999654 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.0 sd_pos=70269 heater_bed: target=55 temp=55.4 pwm=0.280 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451872 bytes_read=24605259 bytes_retransmit=9 bytes_invalid=0 send_seq=72691 receive_seq=72691 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999648 adj=31999750 coil_temp=38.0 refs=0 mcu_temp=34.46 supply_voltage=3.014 sysload=0.24 cputime=3406.980 memavail=1407520 print_time=70848.457 buffer_time=2.313 print_stall=0 extruder: target=220 temp=219.6 pwm=0.435
Resetting prediction variance 70840.766: freq=49997907 diff=2088120 stddev=50000.000
Stats 70841.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=753291 bytes_read=8135760 bytes_retransmit=9 bytes_invalid=0 send_seq=82442 receive_seq=82442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=7769 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000021 bytes_write=420474 bytes_read=1296631 bytes_retransmit=0 bytes_invalid=0 send_seq=70046 receive_seq=70046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000234 adj=50129296 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=467163 bytes_read=7747839 bytes_retransmit=9 bytes_invalid=0 send_seq=72544 receive_seq=72544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999659 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=35.0 sd_pos=71958 heater_bed: target=55 temp=55.3 pwm=0.329 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451878 bytes_read=24605615 bytes_retransmit=9 bytes_invalid=0 send_seq=72692 receive_seq=72692 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999647 adj=31999751 coil_temp=38.1 refs=0 mcu_temp=34.55 supply_voltage=3.014 sysload=0.24 cputime=3407.056 memavail=1407524 print_time=70849.214 buffer_time=2.071 print_stall=0 extruder: target=220 temp=222.1 pwm=0.000
Resetting prediction variance 70841.751: freq=50000234 diff=1983344 stddev=50000.000
Stats 70842.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=761702 bytes_read=8136844 bytes_retransmit=9 bytes_invalid=0 send_seq=82586 receive_seq=82586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=9739 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420480 bytes_read=1296660 bytes_retransmit=0 bytes_invalid=0 send_seq=70047 receive_seq=70047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50002417 adj=50152536 toolboard_t0: mcu_awake=0.011 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=468746 bytes_read=7748148 bytes_retransmit=9 bytes_invalid=0 send_seq=72573 receive_seq=72573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999911 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=35.0 sd_pos=74250 heater_bed: target=55 temp=55.3 pwm=0.277 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451884 bytes_read=24605971 bytes_retransmit=9 bytes_invalid=0 send_seq=72693 receive_seq=72693 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999645 adj=31999743 coil_temp=38.2 refs=0 mcu_temp=34.62 supply_voltage=3.014 sysload=0.24 cputime=3407.150 memavail=1407020 print_time=70850.666 buffer_time=2.522 print_stall=0 extruder: target=220 temp=219.7 pwm=0.587
Resetting prediction variance 70842.735: freq=50002417 diff=1882384 stddev=50000.000
Stats 70843.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=770833 bytes_read=8138004 bytes_retransmit=9 bytes_invalid=0 send_seq=82742 receive_seq=82742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=8489 freq=179999385 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420486 bytes_read=1296676 bytes_retransmit=0 bytes_invalid=0 send_seq=70048 receive_seq=70048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004466 adj=50172778 toolboard_t0: mcu_awake=0.011 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=470230 bytes_read=7748422 bytes_retransmit=9 bytes_invalid=0 send_seq=72601 receive_seq=72601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999883 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=36.0 sd_pos=75591 heater_bed: target=55 temp=55.3 pwm=0.333 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451890 bytes_read=24606327 bytes_retransmit=9 bytes_invalid=0 send_seq=72694 receive_seq=72694 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999644 adj=31999721 coil_temp=38.3 refs=0 mcu_temp=34.70 supply_voltage=3.014 sysload=0.24 cputime=3407.237 memavail=1407020 print_time=70851.629 buffer_time=2.485 print_stall=0 extruder: target=220 temp=219.4 pwm=0.565
Resetting prediction variance 70843.720: freq=50004466 diff=1786074 stddev=50000.000
Stats 70844.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=777657 bytes_read=8138972 bytes_retransmit=9 bytes_invalid=0 send_seq=82857 receive_seq=82857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=6969 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420492 bytes_read=1296692 bytes_retransmit=0 bytes_invalid=0 send_seq=70049 receive_seq=70049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006390 adj=50173527 toolboard_t0: mcu_awake=0.011 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=471159 bytes_read=7748665 bytes_retransmit=9 bytes_invalid=0 send_seq=72620 receive_seq=72620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999406 adj=63999863 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=36.0 sd_pos=76620 heater_bed: target=55 temp=55.3 pwm=0.333 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451896 bytes_read=24606683 bytes_retransmit=9 bytes_invalid=0 send_seq=72695 receive_seq=72695 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999644 adj=31999720 coil_temp=38.4 refs=0 mcu_temp=34.82 supply_voltage=3.014 sysload=0.22 cputime=3407.377 memavail=1406012 print_time=70852.181 buffer_time=2.037 print_stall=0 extruder: target=220 temp=221.9 pwm=0.000
Resetting prediction variance 70844.725: freq=50006390 diff=1696851 stddev=50000.000
Stats 70845.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=785847 bytes_read=8140031 bytes_retransmit=9 bytes_invalid=0 send_seq=82996 receive_seq=82996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=9508 freq=179999393 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420498 bytes_read=1296708 bytes_retransmit=0 bytes_invalid=0 send_seq=70050 receive_seq=70050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008201 adj=50198562 toolboard_t0: mcu_awake=0.011 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=472786 bytes_read=7748959 bytes_retransmit=9 bytes_invalid=0 send_seq=72649 receive_seq=72649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999407 adj=63999813 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=34.1 sd_pos=79655 heater_bed: target=55 temp=55.2 pwm=0.341 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451902 bytes_read=24607039 bytes_retransmit=9 bytes_invalid=0 send_seq=72696 receive_seq=72696 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999643 adj=31999707 coil_temp=38.5 refs=0 mcu_temp=34.90 supply_voltage=3.014 sysload=0.22 cputime=3407.582 memavail=1406012 print_time=70853.254 buffer_time=2.109 print_stall=0 extruder: target=220 temp=220.4 pwm=0.426
Resetting prediction variance 70845.710: freq=50008201 diff=1609473 stddev=50000.000
Stats 70846.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=794748 bytes_read=8141140 bytes_retransmit=9 bytes_invalid=0 send_seq=83145 receive_seq=83145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=9882 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000012 bytes_write=420504 bytes_read=1296724 bytes_retransmit=0 bytes_invalid=0 send_seq=70051 receive_seq=70051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009903 adj=50198812 toolboard_t0: mcu_awake=0.011 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=474047 bytes_read=7749208 bytes_retransmit=9 bytes_invalid=0 send_seq=72672 receive_seq=72672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999407 adj=63999800 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=36.5 sd_pos=82169 heater_bed: target=55 temp=55.2 pwm=0.338 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451908 bytes_read=24607395 bytes_retransmit=9 bytes_invalid=0 send_seq=72697 receive_seq=72697 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999642 adj=31999699 coil_temp=38.5 refs=0 mcu_temp=34.97 supply_voltage=3.014 sysload=0.22 cputime=3407.784 memavail=1406020 print_time=70854.491 buffer_time=2.346 print_stall=0 extruder: target=220 temp=219.1 pwm=0.692
Resetting prediction variance 70846.694: freq=50009903 diff=1523582 stddev=50000.000
Stats 70847.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000013 mcu_task_stddev=0.000010 bytes_write=804742 bytes_read=8142373 bytes_retransmit=9 bytes_invalid=0 send_seq=83313 receive_seq=83313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=11124 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420510 bytes_read=1296753 bytes_retransmit=0 bytes_invalid=0 send_seq=70052 receive_seq=70052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011500 adj=50161098 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000040 mcu_task_stddev=0.000041 bytes_write=475567 bytes_read=7749516 bytes_retransmit=9 bytes_invalid=0 send_seq=72701 receive_seq=72701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=63999406 adj=63999736 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.7 raspberry_pi: temp=34.6 sd_pos=84636 heater_bed: target=55 temp=55.2 pwm=0.338 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451914 bytes_read=24607751 bytes_retransmit=9 bytes_invalid=0 send_seq=72698 receive_seq=72698 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999641 adj=31999699 coil_temp=38.6 refs=0 mcu_temp=35.04 supply_voltage=3.014 sysload=0.22 cputime=3408.000 memavail=1406020 print_time=70855.662 buffer_time=2.516 print_stall=0 extruder: target=220 temp=221.8 pwm=0.000
Resetting prediction variance 70847.679: freq=50011500 diff=1444626 stddev=50000.000
Stats 70848.7: gcodein=0  mcu: mcu_awake=0.025 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=811407 bytes_read=8143343 bytes_retransmit=9 bytes_invalid=0 send_seq=83431 receive_seq=83431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11084 freq=179999394 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420516 bytes_read=1296769 bytes_retransmit=0 bytes_invalid=0 send_seq=70053 receive_seq=70053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013004 adj=50141859 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000040 mcu_task_stddev=0.000041 bytes_write=476758 bytes_read=7749775 bytes_retransmit=9 bytes_invalid=0 send_seq=72723 receive_seq=72723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999405 adj=63999698 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.9 raspberry_pi: temp=35.0 sd_pos=85864 heater_bed: target=55 temp=55.2 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451920 bytes_read=24608107 bytes_retransmit=9 bytes_invalid=0 send_seq=72699 receive_seq=72699 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999640 adj=31999706 coil_temp=38.7 refs=0 mcu_temp=35.12 supply_voltage=3.014 sysload=0.22 cputime=3408.158 memavail=1406020 print_time=70856.450 buffer_time=2.304 print_stall=0 extruder: target=220 temp=221.3 pwm=0.248
Resetting prediction variance 70848.663: freq=50013004 diff=1353585 stddev=50000.000
Resetting prediction variance 70849.647: freq=50014402 diff=1191496 stddev=50000.000
Stats 70849.7: gcodein=0  mcu: mcu_awake=0.025 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=821983 bytes_read=8144592 bytes_retransmit=9 bytes_invalid=0 send_seq=83608 receive_seq=83608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=7780 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420528 bytes_read=1296801 bytes_retransmit=0 bytes_invalid=0 send_seq=70055 receive_seq=70055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015625 adj=50155463 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000040 mcu_task_stddev=0.000041 bytes_write=477861 bytes_read=7750024 bytes_retransmit=9 bytes_invalid=0 send_seq=72746 receive_seq=72746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999401 adj=63999689 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=35.0 sd_pos=87480 heater_bed: target=55 temp=55.2 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451926 bytes_read=24608463 bytes_retransmit=9 bytes_invalid=0 send_seq=72700 receive_seq=72700 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999640 adj=31999700 coil_temp=38.8 refs=0 mcu_temp=35.20 supply_voltage=3.014 sysload=0.20 cputime=3408.302 memavail=1406020 print_time=70857.185 buffer_time=2.038 print_stall=0 extruder: target=220 temp=219.0 pwm=0.745
Resetting prediction variance 70850.632: freq=50015625 diff=1047677 stddev=50000.000
Stats 70850.7: gcodein=0  mcu: mcu_awake=0.025 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=830551 bytes_read=8145720 bytes_retransmit=9 bytes_invalid=0 send_seq=83755 receive_seq=83755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=10593 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420534 bytes_read=1296817 bytes_retransmit=0 bytes_invalid=0 send_seq=70056 receive_seq=70056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016693 adj=50191196 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000040 mcu_task_stddev=0.000041 bytes_write=480140 bytes_read=7750377 bytes_retransmit=9 bytes_invalid=0 send_seq=72787 receive_seq=72787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999399 adj=63999627 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=35.5 sd_pos=90227 heater_bed: target=55 temp=55.2 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451932 bytes_read=24608819 bytes_retransmit=9 bytes_invalid=0 send_seq=72701 receive_seq=72701 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999638 adj=31999689 coil_temp=38.9 refs=0 mcu_temp=35.27 supply_voltage=3.014 sysload=0.20 cputime=3408.406 memavail=1406020 print_time=70858.668 buffer_time=2.521 print_stall=0 extruder: target=220 temp=220.7 pwm=0.229
Resetting prediction variance 70851.616: freq=50016693 diff=917283 stddev=50000.000
Stats 70851.7: gcodein=0  mcu: mcu_awake=0.025 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=839716 bytes_read=8146864 bytes_retransmit=9 bytes_invalid=0 send_seq=83911 receive_seq=83911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=9173 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420540 bytes_read=1296833 bytes_retransmit=0 bytes_invalid=0 send_seq=70057 receive_seq=70057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017623 adj=50128939 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000040 mcu_task_stddev=0.000041 bytes_write=481380 bytes_read=7750646 bytes_retransmit=9 bytes_invalid=0 send_seq=72811 receive_seq=72811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999397 adj=63999597 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=35.0 sd_pos=91609 heater_bed: target=55 temp=55.2 pwm=0.336 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451944 bytes_read=24609191 bytes_retransmit=9 bytes_invalid=0 send_seq=72703 receive_seq=72703 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999635 adj=31999699 coil_temp=39.0 refs=0 mcu_temp=35.37 supply_voltage=3.014 sysload=0.20 cputime=3408.491 memavail=1406020 print_time=70859.480 buffer_time=2.332 print_stall=0 extruder: target=220 temp=221.9 pwm=0.066
Resetting prediction variance 70852.616: freq=50017623 diff=797283 stddev=50000.000
Stats 70852.7: gcodein=0  mcu: mcu_awake=0.025 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=848000 bytes_read=8147948 bytes_retransmit=9 bytes_invalid=0 send_seq=84055 receive_seq=84055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=19 upcoming_bytes=12566 freq=179999390 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=420546 bytes_read=1296862 bytes_retransmit=0 bytes_invalid=0 send_seq=70058 receive_seq=70058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018428 adj=50134213 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000041 mcu_task_stddev=0.000042 bytes_write=483194 bytes_read=7750965 bytes_retransmit=9 bytes_invalid=0 send_seq=72845 receive_seq=72845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=0 freq=63999395 adj=63999598 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=34.6 sd_pos=93936 heater_bed: target=55 temp=55.2 pwm=0.282 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451950 bytes_read=24609547 bytes_retransmit=9 bytes_invalid=0 send_seq=72704 receive_seq=72704 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999634 adj=31999681 coil_temp=39.1 refs=0 mcu_temp=35.45 supply_voltage=3.014 sysload=0.20 cputime=3408.589 memavail=1406020 print_time=70860.871 buffer_time=2.722 print_stall=0 extruder: target=220 temp=219.6 pwm=0.585
Resetting prediction variance 70853.601: freq=50018428 diff=689731 stddev=50000.000
Stats 70853.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=856595 bytes_read=8149092 bytes_retransmit=9 bytes_invalid=0 send_seq=84202 receive_seq=84202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=8952 freq=179999390 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=420552 bytes_read=1296878 bytes_retransmit=0 bytes_invalid=0 send_seq=70059 receive_seq=70059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019121 adj=50102651 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000041 mcu_task_stddev=0.000042 bytes_write=484066 bytes_read=7751203 bytes_retransmit=9 bytes_invalid=0 send_seq=72863 receive_seq=72863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=63999392 adj=63999580 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.9 raspberry_pi: temp=34.6 sd_pos=95058 heater_bed: target=55 temp=55.1 pwm=0.282 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451956 bytes_read=24609903 bytes_retransmit=9 bytes_invalid=0 send_seq=72705 receive_seq=72705 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999633 adj=31999686 coil_temp=39.1 refs=0 mcu_temp=35.52 supply_voltage=3.014 sysload=0.20 cputime=3408.667 memavail=1406020 print_time=70861.361 buffer_time=2.212 print_stall=0 extruder: target=220 temp=219.8 pwm=0.430
Resetting prediction variance 70854.585: freq=50019121 diff=596352 stddev=50000.000
Stats 70854.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=864885 bytes_read=8150171 bytes_retransmit=9 bytes_invalid=0 send_seq=84345 receive_seq=84345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=6362 freq=179999396 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=420558 bytes_read=1296894 bytes_retransmit=0 bytes_invalid=0 send_seq=70060 receive_seq=70060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019718 adj=50110810 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000041 mcu_task_stddev=0.000042 bytes_write=484768 bytes_read=7751427 bytes_retransmit=9 bytes_invalid=0 send_seq=72878 receive_seq=72878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=63999396 adj=63999558 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=34.6 sd_pos=96025 heater_bed: target=55 temp=55.1 pwm=0.282 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451962 bytes_read=24610259 bytes_retransmit=9 bytes_invalid=0 send_seq=72706 receive_seq=72706 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999632 adj=31999677 coil_temp=39.2 refs=0 mcu_temp=35.59 supply_voltage=3.014 sysload=0.19 cputime=3408.817 memavail=1405824 print_time=70862.384 buffer_time=2.234 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Resetting prediction variance 70855.569: freq=50019718 diff=505870 stddev=50000.000
Stats 70855.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=873848 bytes_read=8151290 bytes_retransmit=9 bytes_invalid=0 send_seq=84496 receive_seq=84496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=3271 freq=179999399 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=420564 bytes_read=1296910 bytes_retransmit=0 bytes_invalid=0 send_seq=70061 receive_seq=70061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020222 adj=50113847 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000041 mcu_task_stddev=0.000042 bytes_write=485579 bytes_read=7751641 bytes_retransmit=9 bytes_invalid=0 send_seq=72894 receive_seq=72894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999395 adj=63999579 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=35.0 sd_pos=97368 heater_bed: target=55 temp=55.1 pwm=0.282 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451968 bytes_read=24610615 bytes_retransmit=9 bytes_invalid=0 send_seq=72707 receive_seq=72707 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999632 adj=31999658 coil_temp=39.3 refs=0 mcu_temp=35.66 supply_voltage=3.014 sysload=0.19 cputime=3409.005 memavail=1405824 print_time=70863.479 buffer_time=2.328 print_stall=0 extruder: target=220 temp=219.8 pwm=0.511
Resetting prediction variance 70856.554: freq=50020222 diff=423326 stddev=50000.000
Stats 70856.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=879886 bytes_read=8152218 bytes_retransmit=9 bytes_invalid=0 send_seq=84603 receive_seq=84603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=7068 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=420570 bytes_read=1296926 bytes_retransmit=0 bytes_invalid=0 send_seq=70062 receive_seq=70062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020642 adj=50098744 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000041 mcu_task_stddev=0.000042 bytes_write=487818 bytes_read=7751989 bytes_retransmit=9 bytes_invalid=0 send_seq=72934 receive_seq=72934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999393 adj=63999562 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.9 raspberry_pi: temp=33.6 sd_pos=98471 heater_bed: target=55 temp=55.1 pwm=0.292 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451974 bytes_read=24610971 bytes_retransmit=9 bytes_invalid=0 send_seq=72708 receive_seq=72708 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999633 adj=31999670 coil_temp=39.4 refs=0 mcu_temp=35.74 supply_voltage=3.014 sysload=0.19 cputime=3409.117 memavail=1407588 print_time=70864.703 buffer_time=2.551 print_stall=0 extruder: target=220 temp=219.7 pwm=0.445
Resetting prediction variance 70857.538: freq=50020642 diff=349383 stddev=50000.000
Stats 70857.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=884626 bytes_read=8153002 bytes_retransmit=9 bytes_invalid=0 send_seq=84687 receive_seq=84687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=8590 freq=179999396 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420576 bytes_read=1296955 bytes_retransmit=0 bytes_invalid=0 send_seq=70063 receive_seq=70063 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020988 adj=50081806 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000039 mcu_task_stddev=0.000040 bytes_write=489287 bytes_read=7752293 bytes_retransmit=9 bytes_invalid=0 send_seq=72962 receive_seq=72962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=0 freq=63999390 adj=63999575 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.9 raspberry_pi: temp=35.5 sd_pos=99079 heater_bed: target=55 temp=55.2 pwm=0.292 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451980 bytes_read=24611327 bytes_retransmit=9 bytes_invalid=0 send_seq=72709 receive_seq=72709 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999631 adj=31999708 coil_temp=39.5 refs=0 mcu_temp=35.82 supply_voltage=3.014 sysload=0.19 cputime=3409.184 memavail=1407368 print_time=70865.500 buffer_time=2.348 print_stall=0 extruder: target=220 temp=221.9 pwm=0.000
Resetting prediction variance 70858.522: freq=50020988 diff=283605 stddev=50000.000
Stats 70858.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=892693 bytes_read=8154082 bytes_retransmit=9 bytes_invalid=0 send_seq=84827 receive_seq=84827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=10263 freq=179999388 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420582 bytes_read=1296971 bytes_retransmit=0 bytes_invalid=0 send_seq=70064 receive_seq=70064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021267 adj=50083152 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000039 mcu_task_stddev=0.000040 bytes_write=491802 bytes_read=7752632 bytes_retransmit=9 bytes_invalid=0 send_seq=73007 receive_seq=73003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=63999389 adj=63999530 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=35.0 sd_pos=99998 heater_bed: target=55 temp=55.1 pwm=0.292 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451986 bytes_read=24611683 bytes_retransmit=9 bytes_invalid=0 send_seq=72710 receive_seq=72710 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999629 adj=31999700 coil_temp=39.6 refs=0 mcu_temp=35.94 supply_voltage=3.014 sysload=0.19 cputime=3409.266 memavail=1407368 print_time=70866.812 buffer_time=2.660 print_stall=0 extruder: target=220 temp=219.8 pwm=0.513
Stats 70859.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=900812 bytes_read=8155165 bytes_retransmit=9 bytes_invalid=0 send_seq=84965 receive_seq=84965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=9285 freq=179999386 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420588 bytes_read=1296987 bytes_retransmit=0 bytes_invalid=0 send_seq=70065 receive_seq=70065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021488 adj=50066844 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000039 mcu_task_stddev=0.000040 bytes_write=493598 bytes_read=7752962 bytes_retransmit=9 bytes_invalid=0 send_seq=73040 receive_seq=73040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=63999386 adj=63999577 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.9 raspberry_pi: temp=35.5 sd_pos=100768 heater_bed: target=55 temp=55.1 pwm=0.292 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451992 bytes_read=24612039 bytes_retransmit=9 bytes_invalid=0 send_seq=72711 receive_seq=72711 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999628 adj=31999706 coil_temp=39.6 refs=0 mcu_temp=36.02 supply_voltage=3.014 sysload=0.17 cputime=3409.344 memavail=1407372 print_time=70867.779 buffer_time=2.627 print_stall=0 extruder: target=220 temp=219.2 pwm=0.569
Stats 70860.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=908516 bytes_read=8156194 bytes_retransmit=9 bytes_invalid=0 send_seq=85098 receive_seq=85098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7478 freq=179999381 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420594 bytes_read=1297003 bytes_retransmit=0 bytes_invalid=0 send_seq=70066 receive_seq=70066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021656 adj=50063263 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000039 mcu_task_stddev=0.000040 bytes_write=495036 bytes_read=7753238 bytes_retransmit=9 bytes_invalid=0 send_seq=73067 receive_seq=73067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=0 freq=63999383 adj=63999559 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=34.6 sd_pos=101370 heater_bed: target=55 temp=55.1 pwm=0.292 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=451998 bytes_read=24612389 bytes_retransmit=9 bytes_invalid=0 send_seq=72712 receive_seq=72712 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999626 adj=31999706 coil_temp=39.7 refs=0 mcu_temp=36.09 supply_voltage=3.014 sysload=0.17 cputime=3409.417 memavail=1407372 print_time=70868.506 buffer_time=2.352 print_stall=0 extruder: target=220 temp=222.0 pwm=0.000
Stats 70861.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=916144 bytes_read=8157206 bytes_retransmit=9 bytes_invalid=0 send_seq=85229 receive_seq=85229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=7216 freq=179999400 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420600 bytes_read=1297019 bytes_retransmit=0 bytes_invalid=0 send_seq=70067 receive_seq=70067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021779 adj=50065114 toolboard_t0: mcu_awake=0.015 mcu_task_avg=0.000039 mcu_task_stddev=0.000040 bytes_write=496886 bytes_read=7753530 bytes_retransmit=9 bytes_invalid=0 send_seq=73100 receive_seq=73100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999535 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=35.0 sd_pos=102122 heater_bed: target=55 temp=55.1 pwm=0.276 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452004 bytes_read=24612734 bytes_retransmit=9 bytes_invalid=0 send_seq=72713 receive_seq=72713 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999625 adj=31999695 coil_temp=39.8 refs=0 mcu_temp=36.17 supply_voltage=3.014 sysload=0.17 cputime=3409.564 memavail=1407372 print_time=70869.467 buffer_time=2.313 print_stall=0 extruder: target=220 temp=220.1 pwm=0.428
Stats 70862.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000011 bytes_write=923661 bytes_read=8158244 bytes_retransmit=9 bytes_invalid=0 send_seq=85359 receive_seq=85359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=11642 freq=179999396 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420606 bytes_read=1297048 bytes_retransmit=0 bytes_invalid=0 send_seq=70068 receive_seq=70068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021860 adj=50060147 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=499705 bytes_read=7753935 bytes_retransmit=9 bytes_invalid=0 send_seq=73150 receive_seq=73150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=63999378 adj=63999446 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=34.6 sd_pos=103515 heater_bed: target=55 temp=55.1 pwm=0.276 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452010 bytes_read=24613078 bytes_retransmit=9 bytes_invalid=0 send_seq=72714 receive_seq=72714 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999624 adj=31999652 coil_temp=39.8 refs=0 mcu_temp=36.24 supply_voltage=3.013 sysload=0.17 cputime=3409.748 memavail=1407372 print_time=70870.942 buffer_time=2.788 print_stall=0 extruder: target=220 temp=218.9 pwm=0.628
Stats 70863.7: gcodein=0  mcu: mcu_awake=0.022 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=931031 bytes_read=8159254 bytes_retransmit=9 bytes_invalid=0 send_seq=85485 receive_seq=85485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=11406 freq=179999397 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420612 bytes_read=1297064 bytes_retransmit=0 bytes_invalid=0 send_seq=70069 receive_seq=70069 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021905 adj=50046449 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=501264 bytes_read=7754229 bytes_retransmit=9 bytes_invalid=0 send_seq=73180 receive_seq=73180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999495 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.1 raspberry_pi: temp=35.5 sd_pos=104172 heater_bed: target=55 temp=55.1 pwm=0.276 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452016 bytes_read=24613423 bytes_retransmit=9 bytes_invalid=0 send_seq=72715 receive_seq=72715 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999626 adj=31999674 coil_temp=39.9 refs=0 mcu_temp=36.30 supply_voltage=3.014 sysload=0.17 cputime=3409.910 memavail=1407372 print_time=70871.933 buffer_time=2.778 print_stall=0 extruder: target=220 temp=221.9 pwm=0.000
Stats 70864.7: gcodein=0  mcu: mcu_awake=0.022 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=939418 bytes_read=8160328 bytes_retransmit=9 bytes_invalid=0 send_seq=85627 receive_seq=85627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=7518 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420618 bytes_read=1297080 bytes_retransmit=0 bytes_invalid=0 send_seq=70070 receive_seq=70070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021911 adj=50043532 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=502454 bytes_read=7754473 bytes_retransmit=9 bytes_invalid=0 send_seq=73202 receive_seq=73202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=63999374 adj=63999494 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.1 raspberry_pi: temp=33.6 sd_pos=104539 heater_bed: target=55 temp=55.1 pwm=0.329 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452022 bytes_read=24613768 bytes_retransmit=9 bytes_invalid=0 send_seq=72716 receive_seq=72716 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999624 adj=31999702 coil_temp=40.0 refs=0 mcu_temp=36.35 supply_voltage=3.014 sysload=0.16 cputime=3409.981 memavail=1406124 print_time=70872.573 buffer_time=2.417 print_stall=0 extruder: target=220 temp=220.8 pwm=0.244
Stats 70865.7: gcodein=0  mcu: mcu_awake=0.022 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=947507 bytes_read=8161411 bytes_retransmit=9 bytes_invalid=0 send_seq=85765 receive_seq=85765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=6354 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420624 bytes_read=1297096 bytes_retransmit=0 bytes_invalid=0 send_seq=70071 receive_seq=70071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021887 adj=50043620 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=504221 bytes_read=7754781 bytes_retransmit=9 bytes_invalid=0 send_seq=73234 receive_seq=73234 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=63999373 adj=63999487 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=35.0 sd_pos=105193 heater_bed: target=55 temp=55.1 pwm=0.329 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452028 bytes_read=24614113 bytes_retransmit=9 bytes_invalid=0 send_seq=72717 receive_seq=72717 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999622 adj=31999694 coil_temp=40.1 refs=0 mcu_temp=36.45 supply_voltage=3.014 sysload=0.16 cputime=3410.059 memavail=1406124 print_time=70873.618 buffer_time=2.461 print_stall=0 extruder: target=220 temp=218.9 pwm=0.688
Stats 70866.7: gcodein=0  mcu: mcu_awake=0.022 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=954420 bytes_read=8162375 bytes_retransmit=9 bytes_invalid=0 send_seq=85885 receive_seq=85885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7302 freq=179999388 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000011 bytes_write=420630 bytes_read=1297112 bytes_retransmit=0 bytes_invalid=0 send_seq=70072 receive_seq=70072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021836 adj=50040215 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=506466 bytes_read=7755130 bytes_retransmit=9 bytes_invalid=0 send_seq=73274 receive_seq=73274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=0 freq=63999371 adj=63999494 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=35.0 sd_pos=106067 heater_bed: target=55 temp=55.1 pwm=0.271 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452034 bytes_read=24614458 bytes_retransmit=9 bytes_invalid=0 send_seq=72718 receive_seq=72718 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999620 adj=31999682 coil_temp=40.1 refs=0 mcu_temp=36.52 supply_voltage=3.014 sysload=0.16 cputime=3410.139 memavail=1406124 print_time=70874.818 buffer_time=2.661 print_stall=0 extruder: target=220 temp=221.4 pwm=0.000
Stats 70867.7: gcodein=0  mcu: mcu_awake=0.022 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=961011 bytes_read=8163314 bytes_retransmit=9 bytes_invalid=0 send_seq=86000 receive_seq=86000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=7361 freq=179999379 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420636 bytes_read=1297141 bytes_retransmit=0 bytes_invalid=0 send_seq=70073 receive_seq=70073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021763 adj=50035008 toolboard_t0: mcu_awake=0.020 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=507975 bytes_read=7755414 bytes_retransmit=9 bytes_invalid=0 send_seq=73301 receive_seq=73301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=63999368 adj=63999506 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=38.1 raspberry_pi: temp=35.0 sd_pos=106727 heater_bed: target=55 temp=55.1 pwm=0.271 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452040 bytes_read=24614803 bytes_retransmit=9 bytes_invalid=0 send_seq=72719 receive_seq=72719 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999617 adj=31999673 coil_temp=40.2 refs=0 mcu_temp=36.57 supply_voltage=3.014 sysload=0.16 cputime=3410.213 memavail=1406124 print_time=70875.669 buffer_time=2.512 print_stall=0 extruder: target=220 temp=221.7 pwm=0.000
Stats 70868.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=967875 bytes_read=8164323 bytes_retransmit=9 bytes_invalid=0 send_seq=86120 receive_seq=86120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=6045 freq=179999376 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420642 bytes_read=1297157 bytes_retransmit=0 bytes_invalid=0 send_seq=70074 receive_seq=70074 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021670 adj=50033180 toolboard_t0: mcu_awake=0.020 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=509506 bytes_read=7755707 bytes_retransmit=9 bytes_invalid=0 send_seq=73330 receive_seq=73330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999365 adj=63999505 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=35.5 sd_pos=107266 heater_bed: target=55 temp=55.0 pwm=0.271 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452046 bytes_read=24615149 bytes_retransmit=9 bytes_invalid=0 send_seq=72720 receive_seq=72720 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999670 coil_temp=40.3 refs=0 mcu_temp=36.64 supply_voltage=3.014 sysload=0.16 cputime=3410.296 memavail=1406124 print_time=70876.396 buffer_time=2.238 print_stall=0 extruder: target=220 temp=219.0 pwm=0.661
Stats 70869.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=974946 bytes_read=8165292 bytes_retransmit=9 bytes_invalid=0 send_seq=86241 receive_seq=86241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5054 freq=179999378 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420648 bytes_read=1297173 bytes_retransmit=0 bytes_invalid=0 send_seq=70075 receive_seq=70075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021563 adj=50031887 toolboard_t0: mcu_awake=0.020 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=511156 bytes_read=7756006 bytes_retransmit=9 bytes_invalid=0 send_seq=73360 receive_seq=73360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999489 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=35.0 sd_pos=107800 heater_bed: target=55 temp=55.1 pwm=0.271 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452052 bytes_read=24615505 bytes_retransmit=9 bytes_invalid=0 send_seq=72721 receive_seq=72721 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999662 coil_temp=40.4 refs=0 mcu_temp=36.70 supply_voltage=3.014 sysload=0.23 cputime=3410.456 memavail=1406124 print_time=70877.201 buffer_time=2.042 print_stall=0 extruder: target=220 temp=220.6 pwm=0.171
Unknown command:"TIMELAPSE_TAKE_FRAME"
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70870.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=982863 bytes_read=8166340 bytes_retransmit=9 bytes_invalid=0 send_seq=86376 receive_seq=86375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=11226 freq=179999377 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420654 bytes_read=1297189 bytes_retransmit=0 bytes_invalid=0 send_seq=70076 receive_seq=70076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021439 adj=50029731 toolboard_t0: mcu_awake=0.020 mcu_task_avg=0.000046 mcu_task_stddev=0.000043 bytes_write=514408 bytes_read=7756420 bytes_retransmit=9 bytes_invalid=0 send_seq=73416 receive_seq=73416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=63999367 adj=63999524 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.1 raspberry_pi: temp=34.6 sd_pos=110132 heater_bed: target=55 temp=55.0 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452058 bytes_read=24615879 bytes_retransmit=9 bytes_invalid=0 send_seq=72722 receive_seq=72722 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999615 adj=31999657 coil_temp=40.4 refs=0 mcu_temp=36.77 supply_voltage=3.014 sysload=0.23 cputime=3410.692 memavail=1406124 print_time=70878.982 buffer_time=2.769 print_stall=0 extruder: target=220 temp=222.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70871.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=990177 bytes_read=8167354 bytes_retransmit=9 bytes_invalid=0 send_seq=86502 receive_seq=86502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=9137 freq=179999385 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000014 bytes_write=420660 bytes_read=1297205 bytes_retransmit=0 bytes_invalid=0 send_seq=70077 receive_seq=70077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021298 adj=50024229 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=515112 bytes_read=7756678 bytes_retransmit=9 bytes_invalid=0 send_seq=73432 receive_seq=73432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=9 freq=63999363 adj=63999548 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=35.5 sd_pos=111455 heater_bed: target=55 temp=55.1 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452064 bytes_read=24616235 bytes_retransmit=9 bytes_invalid=0 send_seq=72723 receive_seq=72723 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999613 adj=31999687 coil_temp=40.5 refs=0 mcu_temp=36.84 supply_voltage=3.014 sysload=0.23 cputime=3410.785 memavail=1406124 print_time=70879.453 buffer_time=2.238 print_stall=0 extruder: target=220 temp=218.9 pwm=0.719
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 7000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70872.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=998298 bytes_read=8168408 bytes_retransmit=9 bytes_invalid=0 send_seq=86640 receive_seq=86640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=18016 freq=179999382 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=420666 bytes_read=1297234 bytes_retransmit=0 bytes_invalid=0 send_seq=70078 receive_seq=70078 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50021147 adj=50022593 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=517954 bytes_read=7757057 bytes_retransmit=9 bytes_invalid=0 send_seq=73481 receive_seq=73481 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=27 freq=63999361 adj=63999477 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=35.5 sd_pos=115289 heater_bed: target=55 temp=55.1 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452070 bytes_read=24616591 bytes_retransmit=9 bytes_invalid=0 send_seq=72724 receive_seq=72724 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999612 adj=31999654 coil_temp=40.6 refs=0 mcu_temp=36.94 supply_voltage=3.014 sysload=0.23 cputime=3410.923 memavail=1406252 print_time=70881.000 buffer_time=2.785 print_stall=0 extruder: target=220 temp=220.0 pwm=0.341
Stats 70873.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1006251 bytes_read=8169477 bytes_retransmit=9 bytes_invalid=0 send_seq=86775 receive_seq=86775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=18680 freq=179999391 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=420672 bytes_read=1297250 bytes_retransmit=0 bytes_invalid=0 send_seq=70079 receive_seq=70079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020986 adj=50020638 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=519170 bytes_read=7757311 bytes_retransmit=9 bytes_invalid=0 send_seq=73505 receive_seq=73505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=9 freq=63999358 adj=63999503 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=35.5 sd_pos=117476 heater_bed: target=55 temp=55.1 pwm=0.303 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452076 bytes_read=24616947 bytes_retransmit=9 bytes_invalid=0 send_seq=72725 receive_seq=72725 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999610 adj=31999661 coil_temp=40.6 refs=0 mcu_temp=37.01 supply_voltage=3.014 sysload=0.23 cputime=3411.021 memavail=1406760 print_time=70881.656 buffer_time=2.441 print_stall=0 extruder: target=220 temp=222.6 pwm=0.000
Stats 70874.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1017073 bytes_read=8170771 bytes_retransmit=9 bytes_invalid=0 send_seq=86958 receive_seq=86958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=19112 freq=179999403 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=420678 bytes_read=1297266 bytes_retransmit=0 bytes_invalid=0 send_seq=70080 receive_seq=70080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020816 adj=50018726 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=520693 bytes_read=7757614 bytes_retransmit=9 bytes_invalid=0 send_seq=73533 receive_seq=73533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999355 adj=63999436 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=36.5 sd_pos=120758 heater_bed: target=55 temp=55.1 pwm=0.275 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452082 bytes_read=24617303 bytes_retransmit=9 bytes_invalid=0 send_seq=72726 receive_seq=72726 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999608 adj=31999625 coil_temp=40.7 refs=0 mcu_temp=37.07 supply_voltage=3.014 sysload=0.21 cputime=3411.122 memavail=1406016 print_time=70882.286 buffer_time=2.071 print_stall=0 extruder: target=220 temp=220.2 pwm=0.438
Stats 70875.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1029450 bytes_read=8172170 bytes_retransmit=9 bytes_invalid=0 send_seq=87165 receive_seq=87165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=12 upcoming_bytes=25887 freq=179999402 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=420684 bytes_read=1297282 bytes_retransmit=0 bytes_invalid=0 send_seq=70081 receive_seq=70081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020640 adj=50016502 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=524030 bytes_read=7758038 bytes_retransmit=9 bytes_invalid=0 send_seq=73591 receive_seq=73591 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=63999358 adj=63999349 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.4 raspberry_pi: temp=35.5 sd_pos=123170 heater_bed: target=55 temp=55.1 pwm=0.275 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452088 bytes_read=24617659 bytes_retransmit=9 bytes_invalid=0 send_seq=72727 receive_seq=72727 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999606 adj=31999582 coil_temp=40.7 refs=0 mcu_temp=37.15 supply_voltage=3.014 sysload=0.21 cputime=3411.238 memavail=1405792 print_time=70883.475 buffer_time=2.260 print_stall=0 extruder: target=220 temp=219.2 pwm=0.564
Stats 70876.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1046692 bytes_read=8173973 bytes_retransmit=9 bytes_invalid=0 send_seq=87451 receive_seq=87450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=26151 freq=179999412 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=420690 bytes_read=1297297 bytes_retransmit=0 bytes_invalid=0 send_seq=70082 receive_seq=70082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020459 adj=50015150 toolboard_t0: mcu_awake=0.018 mcu_task_avg=0.000045 mcu_task_stddev=0.000043 bytes_write=526996 bytes_read=7758427 bytes_retransmit=9 bytes_invalid=0 send_seq=73642 receive_seq=73642 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=63999358 adj=63999431 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=34.6 sd_pos=125904 heater_bed: target=55 temp=55.1 pwm=0.275 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452094 bytes_read=24618015 bytes_retransmit=9 bytes_invalid=0 send_seq=72728 receive_seq=72728 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999605 adj=31999593 coil_temp=40.8 refs=0 mcu_temp=37.22 supply_voltage=3.014 sysload=0.21 cputime=3411.416 memavail=1405792 print_time=70884.646 buffer_time=2.430 print_stall=0 extruder: target=220 temp=221.6 pwm=0.000
Stats 70877.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1063662 bytes_read=8175782 bytes_retransmit=9 bytes_invalid=0 send_seq=87736 receive_seq=87736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=19356 freq=179999405 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420696 bytes_read=1297324 bytes_retransmit=0 bytes_invalid=0 send_seq=70083 receive_seq=70083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020275 adj=50014416 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000059 mcu_task_stddev=0.000053 bytes_write=527991 bytes_read=7758696 bytes_retransmit=9 bytes_invalid=0 send_seq=73660 receive_seq=73660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=11 upcoming_bytes=0 freq=63999356 adj=63999436 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=35.5 sd_pos=128051 heater_bed: target=55 temp=55.1 pwm=0.275 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452100 bytes_read=24618371 bytes_retransmit=9 bytes_invalid=0 send_seq=72729 receive_seq=72729 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999603 adj=31999586 coil_temp=40.9 refs=0 mcu_temp=37.29 supply_voltage=3.014 sysload=0.21 cputime=3411.522 memavail=1405792 print_time=70885.271 buffer_time=2.055 print_stall=0 extruder: target=220 temp=220.0 pwm=0.451
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70878.7: gcodein=0  mcu: mcu_awake=0.040 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=1077533 bytes_read=8177322 bytes_retransmit=9 bytes_invalid=0 send_seq=87968 receive_seq=87968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=23851 freq=179999408 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420702 bytes_read=1297339 bytes_retransmit=0 bytes_invalid=0 send_seq=70084 receive_seq=70084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50020087 adj=50011982 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000059 mcu_task_stddev=0.000053 bytes_write=530838 bytes_read=7759080 bytes_retransmit=9 bytes_invalid=0 send_seq=73710 receive_seq=73710 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=63999355 adj=63999435 Octopus_V1.1_F446: temp=34.1 EBB42_v1.2_T0: temp=38.5 raspberry_pi: temp=35.0 sd_pos=132570 heater_bed: target=55 temp=55.0 pwm=0.337 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452106 bytes_read=24618727 bytes_retransmit=9 bytes_invalid=0 send_seq=72730 receive_seq=72730 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999601 adj=31999575 coil_temp=41.0 refs=0 mcu_temp=37.37 supply_voltage=3.014 sysload=0.21 cputime=3411.656 memavail=1405792 print_time=70886.551 buffer_time=2.334 print_stall=0 extruder: target=220 temp=218.2 pwm=0.826
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70879.7: gcodein=0  mcu: mcu_awake=0.040 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=1093816 bytes_read=8179050 bytes_retransmit=9 bytes_invalid=0 send_seq=88238 receive_seq=88238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=13861 freq=179999406 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420708 bytes_read=1297354 bytes_retransmit=0 bytes_invalid=0 send_seq=70085 receive_seq=70085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019897 adj=50012035 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000059 mcu_task_stddev=0.000053 bytes_write=532119 bytes_read=7759334 bytes_retransmit=9 bytes_invalid=0 send_seq=73734 receive_seq=73734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999360 adj=63999448 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=35.0 sd_pos=133274 heater_bed: target=55 temp=55.1 pwm=0.276 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452112 bytes_read=24619083 bytes_retransmit=9 bytes_invalid=0 send_seq=72731 receive_seq=72731 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999590 coil_temp=41.1 refs=0 mcu_temp=37.49 supply_voltage=3.014 sysload=0.19 cputime=3411.754 memavail=1405792 print_time=70887.298 buffer_time=2.082 print_stall=0 extruder: target=220 temp=221.5 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70880.7: gcodein=0  mcu: mcu_awake=0.040 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=1109893 bytes_read=8180774 bytes_retransmit=9 bytes_invalid=0 send_seq=88507 receive_seq=88507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=6079 freq=179999401 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420714 bytes_read=1297369 bytes_retransmit=0 bytes_invalid=0 send_seq=70086 receive_seq=70086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019705 adj=50009592 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000059 mcu_task_stddev=0.000053 bytes_write=533504 bytes_read=7759622 bytes_retransmit=9 bytes_invalid=0 send_seq=73759 receive_seq=73759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=0 freq=63999361 adj=63999526 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=36.0 sd_pos=134125 heater_bed: target=55 temp=55.1 pwm=0.276 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452118 bytes_read=24619439 bytes_retransmit=9 bytes_invalid=0 send_seq=72732 receive_seq=72732 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999600 adj=31999603 coil_temp=41.1 refs=0 mcu_temp=37.58 supply_voltage=3.014 sysload=0.19 cputime=3411.848 memavail=1405792 print_time=70888.336 buffer_time=2.119 print_stall=0 extruder: target=220 temp=221.3 pwm=0.230
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70881.7: gcodein=0  mcu: mcu_awake=0.040 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=1118082 bytes_read=8181833 bytes_retransmit=9 bytes_invalid=0 send_seq=88646 receive_seq=88646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=1790 freq=179999396 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420720 bytes_read=1297384 bytes_retransmit=0 bytes_invalid=0 send_seq=70087 receive_seq=70087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019519 adj=50009237 toolboard_t0: mcu_awake=0.028 mcu_task_avg=0.000059 mcu_task_stddev=0.000053 bytes_write=534288 bytes_read=7759836 bytes_retransmit=9 bytes_invalid=0 send_seq=73775 receive_seq=73775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999567 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=36.5 sd_pos=134603 heater_bed: target=55 temp=55.1 pwm=0.286 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452124 bytes_read=24619795 bytes_retransmit=9 bytes_invalid=0 send_seq=72733 receive_seq=72733 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999600 adj=31999621 coil_temp=41.2 refs=0 mcu_temp=37.66 supply_voltage=3.014 sysload=0.19 cputime=3411.977 memavail=1405792 print_time=70889.856 buffer_time=2.639 print_stall=0 extruder: target=220 temp=218.8 pwm=0.774
Stats 70882.7: gcodein=0  mcu: mcu_awake=0.040 mcu_task_avg=0.000016 mcu_task_stddev=0.000012 bytes_write=1122138 bytes_read=8182611 bytes_retransmit=9 bytes_invalid=0 send_seq=88723 receive_seq=88723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999406 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000016 bytes_write=420726 bytes_read=1297413 bytes_retransmit=0 bytes_invalid=0 send_seq=70088 receive_seq=70088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019332 adj=50011708 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000049 mcu_task_stddev=0.000049 bytes_write=534754 bytes_read=7760045 bytes_retransmit=9 bytes_invalid=0 send_seq=73787 receive_seq=73787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999572 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=36.5 sd_pos=134870 heater_bed: target=55 temp=55.0 pwm=0.286 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452130 bytes_read=24620151 bytes_retransmit=9 bytes_invalid=0 send_seq=72734 receive_seq=72734 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999599 adj=31999660 coil_temp=41.0 refs=0 mcu_temp=37.72 supply_voltage=3.014 sysload=0.19 cputime=3412.099 memavail=1405792 print_time=70891.597 buffer_time=3.379 print_stall=0 extruder: target=220 temp=220.6 pwm=0.237
Stats 70883.7: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=1122340 bytes_read=8183066 bytes_retransmit=9 bytes_invalid=0 send_seq=88738 receive_seq=88738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999400 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000016 bytes_write=420732 bytes_read=1297429 bytes_retransmit=0 bytes_invalid=0 send_seq=70089 receive_seq=70089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50019147 adj=50013386 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000049 mcu_task_stddev=0.000049 bytes_write=534796 bytes_read=7760223 bytes_retransmit=9 bytes_invalid=0 send_seq=73790 receive_seq=73790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999556 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=34.6 sd_pos=134870 heater_bed: target=55 temp=55.0 pwm=0.286 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452136 bytes_read=24620507 bytes_retransmit=9 bytes_invalid=0 send_seq=72735 receive_seq=72735 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999598 adj=31999655 coil_temp=40.7 refs=0 mcu_temp=37.75 supply_voltage=3.014 sysload=0.19 cputime=3412.189 memavail=1405792 print_time=70891.597 buffer_time=2.378 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Stats 70884.7: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=1124200 bytes_read=8183635 bytes_retransmit=9 bytes_invalid=0 send_seq=88779 receive_seq=88779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999395 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000016 bytes_write=420738 bytes_read=1297445 bytes_retransmit=0 bytes_invalid=0 send_seq=70090 receive_seq=70090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018965 adj=50011746 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000049 mcu_task_stddev=0.000049 bytes_write=535180 bytes_read=7760407 bytes_retransmit=9 bytes_invalid=0 send_seq=73800 receive_seq=73800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999573 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.2 raspberry_pi: temp=34.1 sd_pos=135254 heater_bed: target=55 temp=55.0 pwm=0.286 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452142 bytes_read=24620863 bytes_retransmit=9 bytes_invalid=0 send_seq=72736 receive_seq=72736 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999597 adj=31999661 coil_temp=40.5 refs=0 mcu_temp=37.76 supply_voltage=3.014 sysload=0.26 cputime=3412.297 memavail=1404812 print_time=70892.230 buffer_time=2.010 print_stall=0 extruder: target=220 temp=219.6 pwm=0.637
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70885.7: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=1129504 bytes_read=8184515 bytes_retransmit=9 bytes_invalid=0 send_seq=88878 receive_seq=88878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999399 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000016 bytes_write=420744 bytes_read=1297461 bytes_retransmit=0 bytes_invalid=0 send_seq=70091 receive_seq=70091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018781 adj=50010026 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000049 mcu_task_stddev=0.000049 bytes_write=536375 bytes_read=7760656 bytes_retransmit=9 bytes_invalid=0 send_seq=73823 receive_seq=73823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999574 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=38.3 raspberry_pi: temp=34.6 sd_pos=136105 heater_bed: target=55 temp=55.0 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452148 bytes_read=24621219 bytes_retransmit=9 bytes_invalid=0 send_seq=72737 receive_seq=72737 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999596 adj=31999663 coil_temp=40.2 refs=0 mcu_temp=37.74 supply_voltage=3.014 sysload=0.26 cputime=3412.454 memavail=1404832 print_time=70893.274 buffer_time=2.054 print_stall=0 extruder: target=220 temp=219.9 pwm=0.443
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70886.7: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=1133746 bytes_read=8185281 bytes_retransmit=9 bytes_invalid=0 send_seq=88959 receive_seq=88959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=85 freq=179999394 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000016 bytes_write=420750 bytes_read=1297477 bytes_retransmit=0 bytes_invalid=0 send_seq=70092 receive_seq=70092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018600 adj=50008027 toolboard_t0: mcu_awake=0.019 mcu_task_avg=0.000049 mcu_task_stddev=0.000049 bytes_write=537355 bytes_read=7760914 bytes_retransmit=9 bytes_invalid=0 send_seq=73842 receive_seq=73842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=0 freq=63999359 adj=63999578 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=34.6 sd_pos=136590 heater_bed: target=55 temp=55.0 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452154 bytes_read=24621575 bytes_retransmit=9 bytes_invalid=0 send_seq=72738 receive_seq=72738 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999594 adj=31999639 coil_temp=40.0 refs=0 mcu_temp=37.66 supply_voltage=3.014 sysload=0.26 cputime=3412.595 memavail=1404832 print_time=70894.646 buffer_time=2.426 print_stall=0 extruder: target=220 temp=222.8 pwm=0.000
Stats 70887.7: gcodein=0  mcu: mcu_awake=0.032 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=1135503 bytes_read=8185856 bytes_retransmit=9 bytes_invalid=0 send_seq=88999 receive_seq=88999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999389 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=420756 bytes_read=1297506 bytes_retransmit=0 bytes_invalid=0 send_seq=70093 receive_seq=70093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018424 adj=50007074 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000031 mcu_task_stddev=0.000036 bytes_write=537723 bytes_read=7761119 bytes_retransmit=9 bytes_invalid=0 send_seq=73851 receive_seq=73851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999573 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=38.1 raspberry_pi: temp=34.1 sd_pos=136703 heater_bed: target=55 temp=55.1 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452160 bytes_read=24621931 bytes_retransmit=9 bytes_invalid=0 send_seq=72739 receive_seq=72739 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999592 adj=31999638 coil_temp=39.8 refs=0 mcu_temp=37.58 supply_voltage=3.014 sysload=0.26 cputime=3412.704 memavail=1404832 print_time=70895.510 buffer_time=2.289 print_stall=0 extruder: target=220 temp=220.4 pwm=0.451
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70888.7: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1139176 bytes_read=8186620 bytes_retransmit=9 bytes_invalid=0 send_seq=89070 receive_seq=89070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999394 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=420762 bytes_read=1297522 bytes_retransmit=0 bytes_invalid=0 send_seq=70094 receive_seq=70094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018250 adj=50005915 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000031 mcu_task_stddev=0.000036 bytes_write=538736 bytes_read=7761348 bytes_retransmit=9 bytes_invalid=0 send_seq=73870 receive_seq=73870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999620 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=38.0 raspberry_pi: temp=33.6 sd_pos=137322 heater_bed: target=55 temp=55.1 pwm=0.283 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452166 bytes_read=24622287 bytes_retransmit=9 bytes_invalid=0 send_seq=72740 receive_seq=72740 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999591 adj=31999618 coil_temp=39.6 refs=0 mcu_temp=37.46 supply_voltage=3.014 sysload=0.26 cputime=3412.842 memavail=1404840 print_time=70896.739 buffer_time=2.518 print_stall=0 extruder: target=220 temp=219.0 pwm=0.684
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70889.7: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1142886 bytes_read=8187349 bytes_retransmit=9 bytes_invalid=0 send_seq=89143 receive_seq=89143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999394 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=420768 bytes_read=1297538 bytes_retransmit=0 bytes_invalid=0 send_seq=70095 receive_seq=70095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50018079 adj=50007529 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000031 mcu_task_stddev=0.000036 bytes_write=539446 bytes_read=7761586 bytes_retransmit=9 bytes_invalid=0 send_seq=73885 receive_seq=73885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999694 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=34.6 sd_pos=137644 heater_bed: target=55 temp=55.0 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452172 bytes_read=24622643 bytes_retransmit=9 bytes_invalid=0 send_seq=72741 receive_seq=72741 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999589 adj=31999630 coil_temp=39.4 refs=0 mcu_temp=37.35 supply_voltage=3.014 sysload=0.23 cputime=3412.959 memavail=1404836 print_time=70897.557 buffer_time=2.335 print_stall=0 extruder: target=220 temp=221.9 pwm=0.002
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70890.7: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1144699 bytes_read=8187918 bytes_retransmit=9 bytes_invalid=0 send_seq=89184 receive_seq=89184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999388 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=420774 bytes_read=1297554 bytes_retransmit=0 bytes_invalid=0 send_seq=70096 receive_seq=70096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017912 adj=50006083 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000031 mcu_task_stddev=0.000036 bytes_write=540029 bytes_read=7761780 bytes_retransmit=9 bytes_invalid=0 send_seq=73897 receive_seq=73897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999722 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=34.6 sd_pos=137802 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452178 bytes_read=24622999 bytes_retransmit=9 bytes_invalid=0 send_seq=72742 receive_seq=72742 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999587 adj=31999612 coil_temp=39.2 refs=0 mcu_temp=37.25 supply_voltage=3.014 sysload=0.23 cputime=3413.059 memavail=1399824 print_time=70898.375 buffer_time=2.152 print_stall=0 extruder: target=220 temp=221.0 pwm=0.260
Stats 70891.7: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1146458 bytes_read=8188506 bytes_retransmit=9 bytes_invalid=0 send_seq=89223 receive_seq=89223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999386 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000019 bytes_write=420780 bytes_read=1297570 bytes_retransmit=0 bytes_invalid=0 send_seq=70097 receive_seq=70097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017745 adj=50004693 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000031 mcu_task_stddev=0.000036 bytes_write=540364 bytes_read=7761959 bytes_retransmit=9 bytes_invalid=0 send_seq=73906 receive_seq=73906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999699 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.8 raspberry_pi: temp=34.6 sd_pos=137918 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452184 bytes_read=24623355 bytes_retransmit=9 bytes_invalid=0 send_seq=72743 receive_seq=72743 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999586 adj=31999610 coil_temp=39.0 refs=0 mcu_temp=37.13 supply_voltage=3.014 sysload=0.23 cputime=3413.111 memavail=1406368 print_time=70899.826 buffer_time=2.602 print_stall=0 extruder: target=220 temp=218.2 pwm=0.854
Stats 70892.7: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1147445 bytes_read=8189005 bytes_retransmit=9 bytes_invalid=0 send_seq=89250 receive_seq=89250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999377 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420786 bytes_read=1297599 bytes_retransmit=0 bytes_invalid=0 send_seq=70098 receive_seq=70098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017583 adj=50008134 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=540574 bytes_read=7762177 bytes_retransmit=9 bytes_invalid=0 send_seq=73914 receive_seq=73914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=63999366 adj=63999657 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.6 sd_pos=138004 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452190 bytes_read=24623711 bytes_retransmit=9 bytes_invalid=0 send_seq=72744 receive_seq=72744 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999584 adj=31999630 coil_temp=38.8 refs=0 mcu_temp=37.01 supply_voltage=3.014 sysload=0.23 cputime=3413.158 memavail=1406144 print_time=70900.561 buffer_time=2.338 print_stall=0 extruder: target=220 temp=221.5 pwm=0.000
Stats 70893.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1149173 bytes_read=8189579 bytes_retransmit=9 bytes_invalid=0 send_seq=89289 receive_seq=89289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420792 bytes_read=1297615 bytes_retransmit=0 bytes_invalid=0 send_seq=70099 receive_seq=70099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017425 adj=50006283 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=540880 bytes_read=7762346 bytes_retransmit=9 bytes_invalid=0 send_seq=73921 receive_seq=73921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999366 adj=63999649 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.0 sd_pos=138221 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452196 bytes_read=24624067 bytes_retransmit=9 bytes_invalid=0 send_seq=72745 receive_seq=72745 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999582 adj=31999627 coil_temp=38.7 refs=0 mcu_temp=36.85 supply_voltage=3.014 sysload=0.23 cputime=3413.206 memavail=1406144 print_time=70901.494 buffer_time=2.270 print_stall=0 extruder: target=220 temp=222.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70894.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1150735 bytes_read=8190152 bytes_retransmit=9 bytes_invalid=0 send_seq=89325 receive_seq=89325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=0 freq=179999361 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420798 bytes_read=1297631 bytes_retransmit=0 bytes_invalid=0 send_seq=70100 receive_seq=70100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017271 adj=50005857 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=541179 bytes_read=7762520 bytes_retransmit=9 bytes_invalid=0 send_seq=73929 receive_seq=73929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999365 adj=63999671 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.7 raspberry_pi: temp=35.0 sd_pos=138744 heater_bed: target=55 temp=55.2 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452202 bytes_read=24624423 bytes_retransmit=9 bytes_invalid=0 send_seq=72746 receive_seq=72746 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999579 adj=31999629 coil_temp=38.5 refs=0 mcu_temp=36.74 supply_voltage=3.014 sysload=0.22 cputime=3413.263 memavail=1405428 print_time=70902.655 buffer_time=2.431 print_stall=0 extruder: target=220 temp=219.2 pwm=0.686
Stats 70895.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1151753 bytes_read=8190661 bytes_retransmit=9 bytes_invalid=0 send_seq=89354 receive_seq=89354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999358 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420804 bytes_read=1297647 bytes_retransmit=0 bytes_invalid=0 send_seq=70101 receive_seq=70101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50017123 adj=50007080 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=541413 bytes_read=7762723 bytes_retransmit=9 bytes_invalid=0 send_seq=73938 receive_seq=73937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999672 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.5 sd_pos=138831 heater_bed: target=55 temp=55.1 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452208 bytes_read=24624779 bytes_retransmit=9 bytes_invalid=0 send_seq=72747 receive_seq=72747 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999638 coil_temp=38.4 refs=0 mcu_temp=36.62 supply_voltage=3.014 sysload=0.22 cputime=3413.326 memavail=1405436 print_time=70903.311 buffer_time=2.086 print_stall=0 extruder: target=220 temp=220.6 pwm=0.217
Stats 70896.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1153408 bytes_read=8191215 bytes_retransmit=9 bytes_invalid=0 send_seq=89392 receive_seq=89392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999355 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000015 bytes_write=420810 bytes_read=1297663 bytes_retransmit=0 bytes_invalid=0 send_seq=70102 receive_seq=70102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016984 adj=50005152 toolboard_t0: mcu_awake=0.010 mcu_task_avg=0.000032 mcu_task_stddev=0.000037 bytes_write=541738 bytes_read=7762907 bytes_retransmit=9 bytes_invalid=0 send_seq=73947 receive_seq=73947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999651 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.4 raspberry_pi: temp=34.1 sd_pos=138947 heater_bed: target=55 temp=55.2 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452214 bytes_read=24625135 bytes_retransmit=9 bytes_invalid=0 send_seq=72748 receive_seq=72748 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999577 adj=31999620 coil_temp=38.2 refs=0 mcu_temp=36.51 supply_voltage=3.014 sysload=0.22 cputime=3413.432 memavail=1405436 print_time=70904.235 buffer_time=2.010 print_stall=0 extruder: target=220 temp=222.3 pwm=0.000
Stats 70897.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1156724 bytes_read=8191933 bytes_retransmit=9 bytes_invalid=0 send_seq=89457 receive_seq=89457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=179999351 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420816 bytes_read=1297692 bytes_retransmit=0 bytes_invalid=0 send_seq=70103 receive_seq=70103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016850 adj=50004474 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000024 mcu_task_stddev=0.000025 bytes_write=542371 bytes_read=7763126 bytes_retransmit=9 bytes_invalid=0 send_seq=73961 receive_seq=73961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=63999359 adj=63999639 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.6 raspberry_pi: temp=34.6 sd_pos=139291 heater_bed: target=55 temp=55.1 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452220 bytes_read=24625491 bytes_retransmit=9 bytes_invalid=0 send_seq=72749 receive_seq=72749 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999577 adj=31999625 coil_temp=38.1 refs=0 mcu_temp=36.39 supply_voltage=3.014 sysload=0.22 cputime=3413.554 memavail=1405436 print_time=70905.453 buffer_time=2.227 print_stall=0 extruder: target=220 temp=219.9 pwm=0.519
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70898.7: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1159606 bytes_read=8192602 bytes_retransmit=9 bytes_invalid=0 send_seq=89515 receive_seq=89515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999347 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420822 bytes_read=1297708 bytes_retransmit=0 bytes_invalid=0 send_seq=70104 receive_seq=70104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016718 adj=50006788 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000024 mcu_task_stddev=0.000025 bytes_write=543020 bytes_read=7763359 bytes_retransmit=9 bytes_invalid=0 send_seq=73975 receive_seq=73975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999615 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.6 sd_pos=139656 heater_bed: target=55 temp=55.1 pwm=0.259 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452226 bytes_read=24625847 bytes_retransmit=9 bytes_invalid=0 send_seq=72750 receive_seq=72750 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999656 coil_temp=38.0 refs=0 mcu_temp=36.29 supply_voltage=3.014 sysload=0.22 cputime=3413.676 memavail=1405436 print_time=70906.354 buffer_time=2.127 print_stall=0 extruder: target=220 temp=219.5 pwm=0.499
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70899.7: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1163756 bytes_read=8193366 bytes_retransmit=9 bytes_invalid=0 send_seq=89595 receive_seq=89595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999346 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420828 bytes_read=1297724 bytes_retransmit=0 bytes_invalid=0 send_seq=70105 receive_seq=70105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016594 adj=50006300 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000024 mcu_task_stddev=0.000025 bytes_write=543833 bytes_read=7763578 bytes_retransmit=9 bytes_invalid=0 send_seq=73992 receive_seq=73992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999631 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=34.1 sd_pos=140191 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452232 bytes_read=24626203 bytes_retransmit=9 bytes_invalid=0 send_seq=72751 receive_seq=72751 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999682 coil_temp=37.8 refs=0 mcu_temp=36.15 supply_voltage=3.013 sysload=0.20 cputime=3413.814 memavail=1405436 print_time=70907.245 buffer_time=2.017 print_stall=0 extruder: target=220 temp=222.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 5000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Unknown command:"TIMELAPSE_TAKE_FRAME"
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70900.7: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1168659 bytes_read=8194214 bytes_retransmit=9 bytes_invalid=0 send_seq=89686 receive_seq=89686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=2367 freq=179999353 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420834 bytes_read=1297740 bytes_retransmit=0 bytes_invalid=0 send_seq=70106 receive_seq=70106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016470 adj=50005868 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000024 mcu_task_stddev=0.000025 bytes_write=545285 bytes_read=7763842 bytes_retransmit=9 bytes_invalid=0 send_seq=74018 receive_seq=74018 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=9 freq=63999361 adj=63999620 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=34.1 sd_pos=141705 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452238 bytes_read=24626559 bytes_retransmit=9 bytes_invalid=0 send_seq=72752 receive_seq=72752 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999683 coil_temp=37.7 refs=0 mcu_temp=36.06 supply_voltage=3.013 sysload=0.20 cputime=3413.998 memavail=1405436 print_time=70908.271 buffer_time=2.042 print_stall=0 extruder: target=220 temp=220.6 pwm=0.378
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 7000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70901.7: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1172632 bytes_read=8194933 bytes_retransmit=9 bytes_invalid=0 send_seq=89757 receive_seq=89757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=8514 freq=179999353 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=420840 bytes_read=1297756 bytes_retransmit=0 bytes_invalid=0 send_seq=70107 receive_seq=70107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016352 adj=50006465 toolboard_t0: mcu_awake=0.007 mcu_task_avg=0.000024 mcu_task_stddev=0.000025 bytes_write=546737 bytes_read=7764135 bytes_retransmit=9 bytes_invalid=0 send_seq=74044 receive_seq=74044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=27 freq=63999360 adj=63999625 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.5 raspberry_pi: temp=35.0 sd_pos=145102 heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452244 bytes_read=24626915 bytes_retransmit=9 bytes_invalid=0 send_seq=72753 receive_seq=72753 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999577 adj=31999676 coil_temp=37.6 refs=0 mcu_temp=35.98 supply_voltage=3.013 sysload=0.20 cputime=3414.195 memavail=1405436 print_time=70909.269 buffer_time=2.039 print_stall=0 extruder: target=220 temp=219.1 pwm=0.632
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Exiting SD card print (position 146384)
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 36000.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 15000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 70902.7: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000011 mcu_task_stddev=0.000009 bytes_write=1180235 bytes_read=8195952 bytes_retransmit=9 bytes_invalid=0 send_seq=89888 receive_seq=89888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=8710 freq=179999361 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=420846 bytes_read=1297785 bytes_retransmit=0 bytes_invalid=0 send_seq=70108 receive_seq=70108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016236 adj=50006811 toolboard_t0: mcu_awake=0.014 mcu_task_avg=0.000039 mcu_task_stddev=0.000043 bytes_write=548552 bytes_read=7764454 bytes_retransmit=9 bytes_invalid=0 send_seq=74078 receive_seq=74078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=9 freq=63999360 adj=63999600 Octopus_V1.1_F446: temp=33.9 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=34.6  heater_bed: target=55 temp=55.1 pwm=0.308 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452250 bytes_read=24627271 bytes_retransmit=9 bytes_invalid=0 send_seq=72754 receive_seq=72754 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999575 adj=31999660 coil_temp=37.5 refs=0 mcu_temp=35.89 supply_voltage=3.013 sysload=0.20 cputime=3414.327 memavail=1405448 print_time=70910.023 buffer_time=1.793 print_stall=0 extruder: target=220 temp=221.3 pwm=0.074
Stats 70903.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=1191010 bytes_read=8197271 bytes_retransmit=9 bytes_invalid=0 send_seq=90070 receive_seq=90070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2525 freq=179999358 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=420852 bytes_read=1297801 bytes_retransmit=0 bytes_invalid=0 send_seq=70109 receive_seq=70109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016125 adj=50005287 toolboard_t0: mcu_awake=0.014 mcu_task_avg=0.000039 mcu_task_stddev=0.000043 bytes_write=548977 bytes_read=7764643 bytes_retransmit=9 bytes_invalid=0 send_seq=74089 receive_seq=74089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=63999361 adj=63999566 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=34.6  heater_bed: target=55 temp=55.2 pwm=0.250 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452256 bytes_read=24627627 bytes_retransmit=9 bytes_invalid=0 send_seq=72755 receive_seq=72755 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999573 adj=31999615 coil_temp=37.5 refs=0 mcu_temp=35.81 supply_voltage=3.013 sysload=0.20 cputime=3414.434 memavail=1405448 print_time=70911.885 buffer_time=2.655 print_stall=0 extruder: target=220 temp=221.8 pwm=0.064
Stats 70904.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=1193991 bytes_read=8197940 bytes_retransmit=9 bytes_invalid=0 send_seq=90131 receive_seq=90131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999350 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=420858 bytes_read=1297817 bytes_retransmit=0 bytes_invalid=0 send_seq=70110 receive_seq=70110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50016020 adj=50010823 toolboard_t0: mcu_awake=0.014 mcu_task_avg=0.000039 mcu_task_stddev=0.000043 bytes_write=549075 bytes_read=7764836 bytes_retransmit=9 bytes_invalid=0 send_seq=74095 receive_seq=74095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999603 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.3 raspberry_pi: temp=36.0  heater_bed: target=55 temp=55.2 pwm=0.306 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452262 bytes_read=24627983 bytes_retransmit=9 bytes_invalid=0 send_seq=72756 receive_seq=72756 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999647 coil_temp=37.4 refs=0 mcu_temp=35.74 supply_voltage=3.013 sysload=0.18 cputime=3414.482 memavail=1403940 print_time=70911.885 buffer_time=1.654 print_stall=0 extruder: target=220 temp=218.6 pwm=0.772
Stats 70905.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=1194203 bytes_read=8198379 bytes_retransmit=9 bytes_invalid=0 send_seq=90146 receive_seq=90146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999343 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=420864 bytes_read=1297833 bytes_retransmit=0 bytes_invalid=0 send_seq=70111 receive_seq=70111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015918 adj=50009711 toolboard_t0: mcu_awake=0.014 mcu_task_avg=0.000039 mcu_task_stddev=0.000043 bytes_write=549149 bytes_read=7765010 bytes_retransmit=9 bytes_invalid=0 send_seq=74101 receive_seq=74101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999355 adj=63999603 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=35.0  heater_bed: target=55 temp=55.2 pwm=0.253 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452268 bytes_read=24628339 bytes_retransmit=9 bytes_invalid=0 send_seq=72757 receive_seq=72757 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999647 coil_temp=37.3 refs=0 mcu_temp=35.68 supply_voltage=3.013 sysload=0.18 cputime=3414.523 memavail=1403724 print_time=70911.885 buffer_time=0.653 print_stall=0 extruder: target=220 temp=220.4 pwm=0.269
Stats 70906.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=1195762 bytes_read=8198957 bytes_retransmit=9 bytes_invalid=0 send_seq=90183 receive_seq=90183 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999342 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000014 bytes_write=420870 bytes_read=1297849 bytes_retransmit=0 bytes_invalid=0 send_seq=70112 receive_seq=70112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015821 adj=50008655 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=549198 bytes_read=7765193 bytes_retransmit=9 bytes_invalid=0 send_seq=74105 receive_seq=74105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999354 adj=63999592 Octopus_V1.1_F446: temp=34.3 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=35.0  heater_bed: target=55 temp=55.1 pwm=0.270 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452274 bytes_read=24628695 bytes_retransmit=9 bytes_invalid=0 send_seq=72758 receive_seq=72758 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999642 coil_temp=37.3 refs=0 mcu_temp=35.60 supply_voltage=3.013 sysload=0.18 cputime=3414.587 memavail=1403724 print_time=70911.885 buffer_time=0.000 print_stall=0 extruder: target=220 temp=222.5 pwm=0.012
Stats 70907.7: gcodein=0  mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=1195964 bytes_read=8199396 bytes_retransmit=9 bytes_invalid=0 send_seq=90198 receive_seq=90198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999346 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=420876 bytes_read=1297878 bytes_retransmit=0 bytes_invalid=0 send_seq=70113 receive_seq=70113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015740 adj=50007593 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=549274 bytes_read=7765367 bytes_retransmit=9 bytes_invalid=0 send_seq=74110 receive_seq=74110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999355 adj=63999578 Octopus_V1.1_F446: temp=34.1 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=35.0  heater_bed: target=55 temp=55.1 pwm=0.270 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452280 bytes_read=24629051 bytes_retransmit=9 bytes_invalid=0 send_seq=72759 receive_seq=72759 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999632 coil_temp=37.3 refs=0 mcu_temp=35.56 supply_voltage=3.014 sysload=0.18 cputime=3414.675 memavail=1400196 print_time=70911.885 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.1 pwm=0.709
Stats 70908.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000034 mcu_task_stddev=0.000097 bytes_write=1196166 bytes_read=8199851 bytes_retransmit=9 bytes_invalid=0 send_seq=90213 receive_seq=90213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999344 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=420888 bytes_read=1297910 bytes_retransmit=0 bytes_invalid=0 send_seq=70115 receive_seq=70115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015572 adj=50006531 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=549356 bytes_read=7765531 bytes_retransmit=9 bytes_invalid=0 send_seq=74116 receive_seq=74116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999352 adj=63999585 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=34.6  heater_bed: target=55 temp=55.1 pwm=0.270 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452286 bytes_read=24629407 bytes_retransmit=9 bytes_invalid=0 send_seq=72760 receive_seq=72760 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999644 coil_temp=37.4 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.18 cputime=3414.717 memavail=1405232 print_time=70911.885 buffer_time=0.000 print_stall=0 extruder: target=220 temp=219.7 pwm=0.443
Starting SD card print (position 146384)
Transition to shutdown state: MCU shutdown
Dumping gcode input 0 blocks
Dumping 20 requests for client 4123225008
Received 1988.836643: b'{"id":4044291808,"method":"objects/query","params":{"objects":{"extruder":["can_extrude"]}}}'
Received 69943.859294: b'{"id":4044200304,"method":"objects/query","params":{"objects":{"gcode":["commands"]}}}'
Received 69943.875568: b'{"id":4044200592,"method":"info","params":{}}'
Received 69943.875568: b'{"id":4044199608,"method":"objects/list","params":{}}'
Received 69943.977059: b'{"id":4044199488,"method":"objects/subscribe","params":{"objects":{"gcode":null,"webhooks":null,"configfile":null,"mcu":null,"mcu rpi":null,"mcu toolboard_t0":null,"heaters":null,"temperature_sensor Octopus_V1.1_F446":null,"temperature_sensor EBB42_v1.2_T0":null,"gcode_macro RatOS":null,"gcode_macro HOME_X":null,"gcode_macro HOME_Y":null,"gcode_macro HOME_Z":null,"gcode_macro HOME_X_SENSORLESS":null,"gcode_macro HOME_Y_SENSORLESS":null,"gcode_macro _Z_HOP":null,"gcode_macro _MOVE_TO_SAFE_Z_HOME":null,"gcode_macro MAYBE_HOME":null,"gcode_macro PID_CALIBRATE_HOTEND":null,"gcode_macro PID_CALIBRATE_BED":null,"gcode_macro PID_CALIBRATE_CHAMBER_HEATER":null,"gcode_macro INITIALIZE_PA_TUNING":null,"gcode_macro CHAMBER_FILTER_ON":null,"gcode_macro CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_ON":null,"gcode_macro _CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_TURN_ON":null,"gcode_macro _CHAMBER_FILTER_TURN_OFF":null,"gcode_macro _CHAMBER_FILTER_SANITY_CHECK":null,"gcode_macro CHAMBER_HEATER_ON":null,"gcode_macro CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_ON":null,"gcode_macro _CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF":null,"gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING":null,"gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING":null,"gcode_macro _LED_START_PRINTING":null,"gcode_macro _LED_START_PRINTING_ERROR":null,"gcode_macro _LED_PRINTING":null,"gcode_macro _LED_PAUSE":null,"gcode_macro _LED_CHAMBER_FILTER_ON":null,"gcode_macro _LED_CHAMBER_FILTER_OFF":null,"gcode_macro _LED_LOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_LOADED":null,"gcode_macro _LED_FILAMENT_RUNOUT":null,"gcode_macro _LED_FILAMENT_CLOG":null,"gcode_macro _LED_UNLOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_UNLOADED":null,"gcode_macro _LED_DEACTIVATE_TOOLHEAD":null,"gcode_macro _LED_TOOLHEAD_STANDBY":null,"gcode_macro _LED_TOOLHEAD_WAKEUP":null,"gcode_macro _LED_MOTORS_OFF":null,"gcode_macro _LED_INPUT_SHAPER_START":null,"gcode_macro _LED_INPUT_SHAPER_END":null,"gcode_macro _LED_BEACON_CALIBRATION_START":null,"gcode_macro _LED_BEACON_CALIBRATION_END":null,"gcode_macro _LED_BEACON_CALIBRATION_ERROR":null,"gcode_macro _LED_VAOC_ON":null,"gcode_macro _LED_VAOC_OFF":null,"gcode_macro _LED_ACTION":null,"gcode_macro _LED_SUCCESS":null,"gcode_macro _LED_HEATING":null,"gcode_macro _LED_COOLING":null,"gcode_macro _LED_ERROR":null,"gcode_macro _LED_ON":null,"gcode_macro _LED_OFF":null,"gcode_macro _LED_STANDBY":null,"gcode_macro _LED_SET":null,"gcode_macro _USER_LED_SET":null,"gcode_macro LOAD_FILAMENT":null,"gcode_macro _DEFAULT_LOAD_FILAMENT":null,"gcode_macro _IDEX_LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE":null,"gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT":null,"gcode_macro _PURGE_BEFORE_UNLOAD":null,"gcode_macro _PURGE_FILAMENT":null,"gcode_macro _MOVE_TO_PARKING_POSITION":null,"gcode_macro _MOVE_TO_LOADING_POSITION":null,"gcode_macro _CLEANING_MOVE":null,"gcode_macro _START_PRINT_BED_MESH":null,"gcode_macro CALIBRATE_ADAPTIVE_MESH":null,"gcode_macro M84":null,"gcode_macro M104":null,"gcode_macro M109":null,"gcode_macro SET_HEATER_TEMPERATURE":null,"gcode_macro TEMPERATURE_WAIT":null,"gcode_macro SET_GCODE_OFFSET":null,"gcode_macro SDCARD_PRINT_FILE":null,"gcode_macro SKEW_PROFILE":null,"gcode_macro SET_SKEW":null,"gcode_macro SET_VELOCITY_LIMIT":null,"gcode_macro _START_PRINT_PARK":null,"gcode_macro _END_PRINT_PARK":null,"gcode_macro _PARK":null,"gcode_macro SAVE_PROBE_RESULT":null,"gcode_macro PROBE_FOR_PRIMING":null,"gcode_macro RESET_PRIME_PROBE_STATE":null,"gcode_macro PROBE_CURRENT_POSITION":null,"gcode_macro PRIME_BLOB":null,"gcode_macro UNLOAD_FILAMENT":null,"gcode_macro _LEGACY_UNLOAD_FILAMENT":null,"gcode_macro _DEFAULT_UNLOAD_FILAMENT":null,"gcode_macro _IDEX_UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE":null,"gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER":null,"gcode_macro _UNLOAD_WITH_TIP_FORMING":null,"gcode_macro _UNLOAD_KNOWN_FILAMENT":null,"gcode_macro _UNLOAD_UNKNOWN_FILAMENT":null,"gcode_macro _TIP_FORMING":null,"gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_FILAMENT_END":null,"gcode_macro M600":null,"gcode_macro COLD_PULL":null,"gcode_macro _USER_START_PRINT_BEFORE_HOMING":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _USER_START_PRINT_BED_MESH":null,"gcode_macro _USER_START_PRINT_PARK":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _USER_START_PRINT_HEAT_CHAMBER":null,"gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_PARK":null,"gcode_macro _USER_END_PRINT_FINISHED":null,"gcode_macro _USER_START_PRINT":null,"gcode_macro _USER_END_START_PRINT":null,"gcode_macro _USER_START_FEATURE":null,"gcode_macro _USER_END_FEATURE":null,"gcode_macro ECHO_T_VARS":null,"gcode_macro ECHO_RATOS_VARS":null,"gcode_macro INITIAL_FRONTEND_UPDATE":null,"gcode_macro CALCULATE_PRINTABLE_AREA":null,"gcode_macro CACHE_TOOLHEAD_SETTINGS":null,"gcode_macro RESTORE_TOOLHEAD_SETTINGS":null,"gcode_macro SET_MACRO_TRAVEL_SETTINGS":null,"gcode_macro SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro VERIFY_HYBRID_INVERTED":null,"gcode_macro RATOS_ECHO":null,"gcode_macro ENABLE_DEBUG":null,"gcode_macro DISABLE_DEBUG":null,"gcode_macro DEBUG_ECHO":null,"gcode_macro START_FEATURE":null,"gcode_macro END_FEATURE":null,"gcode_macro _ON_LAYER_CHANGE":null,"gcode_macro _LEARN_MORE_CALIBRATION":null,"gcode_macro _LEARN_MORE_CHAMBER_FILTER":null,"gcode_macro _LEARN_MORE_FILAMENT":null,"gcode_macro _CONSOLE_SAVE_CONFIG":null,"gcode_macro SAVE_Z_OFFSET":null,"gcode_macro _LOAD_RATOS_SKEW_PROFILE":null,"gcode_macro M601":null,"gcode_macro PAUSE":null,"gcode_macro RESUME":null,"gcode_macro CANCEL_PRINT":null,"gcode_macro START_PRINT":null,"gcode_macro _START_PRINT_BEFORE_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _PRIME":null,"gcode_macro END_PRINT":null,"gcode_macro _END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _SET_EXTRUSION_MODE":null,"gcode_macro GENERATE_SHAPER_GRAPHS":null,"gcode_macro MEASURE_COREXY_BELT_TENSION":null,"idle_timeout":null,"temperature_host raspberry_pi":null,"temperature_sensor raspberry_pi":null,"gcode_move":null,"print_stats":null,"virtual_sdcard":null,"display_status":null,"pause_resume":null,"ratos":null,"exclude_object":null,"heater_bed":null,"fan":null,"heater_fan toolhead_cooling_fan":null,"gcode_macro Z_TILT_ADJUST":null,"bed_mesh":null,"z_tilt":null,"firmware_retraction":null,"stepper_enable":null,"tmc2209 stepper_x":null,"tmc2209 stepper_x1":null,"tmc2209 stepper_y":null,"tmc2209 stepper_y1":null,"tmc2209 stepper_z":null,"tmc2209 stepper_z1":null,"tmc2209 stepper_z2":null,"tmc2209 extruder":null,"beacons":null,"mcu beacon":null,"probe":null,"temperature_sensor beacon_coil":null,"beacon":null,"gcode_macro BEACON_RATOS_CALIBRATION":null,"gcode_macro BEACON_RATOS_CALIBRATE":null,"gcode_macro BEACON_INITIAL_CALIBRATION":null,"gcode_macro BEACON_FINAL_CALIBRATION":null,"gcode_macro BEACON_POKE_TEST":null,"gcode_macro _BEACON_PROBE_POKE":null,"gcode_macro _BEACON_STORE_POKE":null,"gcode_macro _BEACON_CHECK_POKE":null,"gcode_macro _BEACON_ECHO_POKE":null,"gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS":null,"gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET":null,"gcode_macro BEACON_MEASURE_GANTRY_TWIST":null,"gcode_macro _BEACON_PROBE_GANTRY_TWIST":null,"gcode_macro _BEACON_STORE_GANTRY_TWIST":null,"gcode_macro _BEACON_ECHO_GANTRY_TWIST":null,"gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH":null,"gcode_macro _BEACON_APPLY_SCAN_COMPENSATION":null,"gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION":null,"gcode_macro _BEACON_HOME_AND_ABL":null,"gcode_macro _BEACON_SAVE_MULTIPLIER":null,"gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER":null,"controller_fan controller_fan":null,"gcode_macro T0":null,"save_variables":null,"filament_switch_sensor toolhead_filament_sensor_t0":null,"gcode_button toolhead_filament_sensor_button_t0":null,"output_pin caselight":null,"motion_report":null,"query_endstops":null,"system_stats":null,"manual_probe":null,"toolhead":null,"extruder":null},"response_template":{"method":"process_status_update"}}}'
Received 69944.933359: b'{"id":4044288928,"method":"objects/query","params":{"objects":{"extruder":["can_extrude"]}}}'
Received 70146.732540: b'{"id":4044108056,"method":"objects/query","params":{"objects":{"gcode":["commands"]}}}'
Received 70146.732540: b'{"id":4079300888,"method":"info","params":{}}'
Received 70146.732540: b'{"id":4079301032,"method":"objects/list","params":{}}'
Received 70147.093277: b'{"id":4079302928,"method":"objects/subscribe","params":{"objects":{"gcode":null,"webhooks":null,"configfile":null,"mcu":null,"mcu rpi":null,"mcu toolboard_t0":null,"heaters":null,"temperature_sensor Octopus_V1.1_F446":null,"temperature_sensor EBB42_v1.2_T0":null,"gcode_macro RatOS":null,"gcode_macro HOME_X":null,"gcode_macro HOME_Y":null,"gcode_macro HOME_Z":null,"gcode_macro HOME_X_SENSORLESS":null,"gcode_macro HOME_Y_SENSORLESS":null,"gcode_macro _Z_HOP":null,"gcode_macro _MOVE_TO_SAFE_Z_HOME":null,"gcode_macro MAYBE_HOME":null,"gcode_macro PID_CALIBRATE_HOTEND":null,"gcode_macro PID_CALIBRATE_BED":null,"gcode_macro PID_CALIBRATE_CHAMBER_HEATER":null,"gcode_macro INITIALIZE_PA_TUNING":null,"gcode_macro CHAMBER_FILTER_ON":null,"gcode_macro CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_ON":null,"gcode_macro _CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_TURN_ON":null,"gcode_macro _CHAMBER_FILTER_TURN_OFF":null,"gcode_macro _CHAMBER_FILTER_SANITY_CHECK":null,"gcode_macro CHAMBER_HEATER_ON":null,"gcode_macro CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_ON":null,"gcode_macro _CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF":null,"gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING":null,"gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING":null,"gcode_macro _LED_START_PRINTING":null,"gcode_macro _LED_START_PRINTING_ERROR":null,"gcode_macro _LED_PRINTING":null,"gcode_macro _LED_PAUSE":null,"gcode_macro _LED_CHAMBER_FILTER_ON":null,"gcode_macro _LED_CHAMBER_FILTER_OFF":null,"gcode_macro _LED_LOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_LOADED":null,"gcode_macro _LED_FILAMENT_RUNOUT":null,"gcode_macro _LED_FILAMENT_CLOG":null,"gcode_macro _LED_UNLOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_UNLOADED":null,"gcode_macro _LED_DEACTIVATE_TOOLHEAD":null,"gcode_macro _LED_TOOLHEAD_STANDBY":null,"gcode_macro _LED_TOOLHEAD_WAKEUP":null,"gcode_macro _LED_MOTORS_OFF":null,"gcode_macro _LED_INPUT_SHAPER_START":null,"gcode_macro _LED_INPUT_SHAPER_END":null,"gcode_macro _LED_BEACON_CALIBRATION_START":null,"gcode_macro _LED_BEACON_CALIBRATION_END":null,"gcode_macro _LED_BEACON_CALIBRATION_ERROR":null,"gcode_macro _LED_VAOC_ON":null,"gcode_macro _LED_VAOC_OFF":null,"gcode_macro _LED_ACTION":null,"gcode_macro _LED_SUCCESS":null,"gcode_macro _LED_HEATING":null,"gcode_macro _LED_COOLING":null,"gcode_macro _LED_ERROR":null,"gcode_macro _LED_ON":null,"gcode_macro _LED_OFF":null,"gcode_macro _LED_STANDBY":null,"gcode_macro _LED_SET":null,"gcode_macro _USER_LED_SET":null,"gcode_macro LOAD_FILAMENT":null,"gcode_macro _DEFAULT_LOAD_FILAMENT":null,"gcode_macro _IDEX_LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE":null,"gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT":null,"gcode_macro _PURGE_BEFORE_UNLOAD":null,"gcode_macro _PURGE_FILAMENT":null,"gcode_macro _MOVE_TO_PARKING_POSITION":null,"gcode_macro _MOVE_TO_LOADING_POSITION":null,"gcode_macro _CLEANING_MOVE":null,"gcode_macro _START_PRINT_BED_MESH":null,"gcode_macro CALIBRATE_ADAPTIVE_MESH":null,"gcode_macro M84":null,"gcode_macro M104":null,"gcode_macro M109":null,"gcode_macro SET_HEATER_TEMPERATURE":null,"gcode_macro TEMPERATURE_WAIT":null,"gcode_macro SET_GCODE_OFFSET":null,"gcode_macro SDCARD_PRINT_FILE":null,"gcode_macro SKEW_PROFILE":null,"gcode_macro SET_SKEW":null,"gcode_macro SET_VELOCITY_LIMIT":null,"gcode_macro _START_PRINT_PARK":null,"gcode_macro _END_PRINT_PARK":null,"gcode_macro _PARK":null,"gcode_macro SAVE_PROBE_RESULT":null,"gcode_macro PROBE_FOR_PRIMING":null,"gcode_macro RESET_PRIME_PROBE_STATE":null,"gcode_macro PROBE_CURRENT_POSITION":null,"gcode_macro PRIME_BLOB":null,"gcode_macro UNLOAD_FILAMENT":null,"gcode_macro _LEGACY_UNLOAD_FILAMENT":null,"gcode_macro _DEFAULT_UNLOAD_FILAMENT":null,"gcode_macro _IDEX_UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE":null,"gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER":null,"gcode_macro _UNLOAD_WITH_TIP_FORMING":null,"gcode_macro _UNLOAD_KNOWN_FILAMENT":null,"gcode_macro _UNLOAD_UNKNOWN_FILAMENT":null,"gcode_macro _TIP_FORMING":null,"gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_FILAMENT_END":null,"gcode_macro M600":null,"gcode_macro COLD_PULL":null,"gcode_macro _USER_START_PRINT_BEFORE_HOMING":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _USER_START_PRINT_BED_MESH":null,"gcode_macro _USER_START_PRINT_PARK":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _USER_START_PRINT_HEAT_CHAMBER":null,"gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_PARK":null,"gcode_macro _USER_END_PRINT_FINISHED":null,"gcode_macro _USER_START_PRINT":null,"gcode_macro _USER_END_START_PRINT":null,"gcode_macro _USER_START_FEATURE":null,"gcode_macro _USER_END_FEATURE":null,"gcode_macro ECHO_T_VARS":null,"gcode_macro ECHO_RATOS_VARS":null,"gcode_macro INITIAL_FRONTEND_UPDATE":null,"gcode_macro CALCULATE_PRINTABLE_AREA":null,"gcode_macro CACHE_TOOLHEAD_SETTINGS":null,"gcode_macro RESTORE_TOOLHEAD_SETTINGS":null,"gcode_macro SET_MACRO_TRAVEL_SETTINGS":null,"gcode_macro SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro VERIFY_HYBRID_INVERTED":null,"gcode_macro RATOS_ECHO":null,"gcode_macro ENABLE_DEBUG":null,"gcode_macro DISABLE_DEBUG":null,"gcode_macro DEBUG_ECHO":null,"gcode_macro START_FEATURE":null,"gcode_macro END_FEATURE":null,"gcode_macro _ON_LAYER_CHANGE":null,"gcode_macro _LEARN_MORE_CALIBRATION":null,"gcode_macro _LEARN_MORE_CHAMBER_FILTER":null,"gcode_macro _LEARN_MORE_FILAMENT":null,"gcode_macro _CONSOLE_SAVE_CONFIG":null,"gcode_macro SAVE_Z_OFFSET":null,"gcode_macro _LOAD_RATOS_SKEW_PROFILE":null,"gcode_macro M601":null,"gcode_macro PAUSE":null,"gcode_macro RESUME":null,"gcode_macro CANCEL_PRINT":null,"gcode_macro START_PRINT":null,"gcode_macro _START_PRINT_BEFORE_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _PRIME":null,"gcode_macro END_PRINT":null,"gcode_macro _END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _SET_EXTRUSION_MODE":null,"gcode_macro GENERATE_SHAPER_GRAPHS":null,"gcode_macro MEASURE_COREXY_BELT_TENSION":null,"idle_timeout":null,"temperature_host raspberry_pi":null,"temperature_sensor raspberry_pi":null,"gcode_move":null,"print_stats":null,"virtual_sdcard":null,"display_status":null,"pause_resume":null,"ratos":null,"exclude_object":null,"heater_bed":null,"fan":null,"heater_fan toolhead_cooling_fan":null,"gcode_macro Z_TILT_ADJUST":null,"bed_mesh":null,"z_tilt":null,"firmware_retraction":null,"stepper_enable":null,"tmc2209 stepper_x":null,"tmc2209 stepper_x1":null,"tmc2209 stepper_y":null,"tmc2209 stepper_y1":null,"tmc2209 stepper_z":null,"tmc2209 stepper_z1":null,"tmc2209 stepper_z2":null,"tmc2209 extruder":null,"beacons":null,"mcu beacon":null,"probe":null,"temperature_sensor beacon_coil":null,"beacon":null,"gcode_macro BEACON_RATOS_CALIBRATION":null,"gcode_macro BEACON_RATOS_CALIBRATE":null,"gcode_macro BEACON_INITIAL_CALIBRATION":null,"gcode_macro BEACON_FINAL_CALIBRATION":null,"gcode_macro BEACON_POKE_TEST":null,"gcode_macro _BEACON_PROBE_POKE":null,"gcode_macro _BEACON_STORE_POKE":null,"gcode_macro _BEACON_CHECK_POKE":null,"gcode_macro _BEACON_ECHO_POKE":null,"gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS":null,"gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET":null,"gcode_macro BEACON_MEASURE_GANTRY_TWIST":null,"gcode_macro _BEACON_PROBE_GANTRY_TWIST":null,"gcode_macro _BEACON_STORE_GANTRY_TWIST":null,"gcode_macro _BEACON_ECHO_GANTRY_TWIST":null,"gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH":null,"gcode_macro _BEACON_APPLY_SCAN_COMPENSATION":null,"gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION":null,"gcode_macro _BEACON_HOME_AND_ABL":null,"gcode_macro _BEACON_SAVE_MULTIPLIER":null,"gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER":null,"controller_fan controller_fan":null,"gcode_macro T0":null,"save_variables":null,"filament_switch_sensor toolhead_filament_sensor_t0":null,"gcode_button toolhead_filament_sensor_button_t0":null,"output_pin caselight":null,"motion_report":null,"query_endstops":null,"system_stats":null,"manual_probe":null,"toolhead":null,"extruder":null},"response_template":{"method":"process_status_update"}}}'
Received 70148.813176: b'{"id":4044110768,"method":"objects/query","params":{"objects":{"extruder":["can_extrude"]}}}'
Received 70403.590152: b'{"id":4044291040,"method":"objects/query","params":{"objects":{"gcode":["commands"]}}}'
Received 70403.590152: b'{"id":4088373176,"method":"info","params":{}}'
Received 70403.590152: b'{"id":4044288640,"method":"objects/list","params":{}}'
Received 70403.784400: b'{"id":4044291736,"method":"objects/subscribe","params":{"objects":{"gcode":null,"webhooks":null,"configfile":null,"mcu":null,"mcu rpi":null,"mcu toolboard_t0":null,"heaters":null,"temperature_sensor Octopus_V1.1_F446":null,"temperature_sensor EBB42_v1.2_T0":null,"gcode_macro RatOS":null,"gcode_macro HOME_X":null,"gcode_macro HOME_Y":null,"gcode_macro HOME_Z":null,"gcode_macro HOME_X_SENSORLESS":null,"gcode_macro HOME_Y_SENSORLESS":null,"gcode_macro _Z_HOP":null,"gcode_macro _MOVE_TO_SAFE_Z_HOME":null,"gcode_macro MAYBE_HOME":null,"gcode_macro PID_CALIBRATE_HOTEND":null,"gcode_macro PID_CALIBRATE_BED":null,"gcode_macro PID_CALIBRATE_CHAMBER_HEATER":null,"gcode_macro INITIALIZE_PA_TUNING":null,"gcode_macro CHAMBER_FILTER_ON":null,"gcode_macro CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_ON":null,"gcode_macro _CHAMBER_FILTER_OFF":null,"gcode_macro _CHAMBER_FILTER_TURN_ON":null,"gcode_macro _CHAMBER_FILTER_TURN_OFF":null,"gcode_macro _CHAMBER_FILTER_SANITY_CHECK":null,"gcode_macro CHAMBER_HEATER_ON":null,"gcode_macro CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_ON":null,"gcode_macro _CHAMBER_HEATER_OFF":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON":null,"gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF":null,"gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING":null,"gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING":null,"gcode_macro _LED_START_PRINTING":null,"gcode_macro _LED_START_PRINTING_ERROR":null,"gcode_macro _LED_PRINTING":null,"gcode_macro _LED_PAUSE":null,"gcode_macro _LED_CHAMBER_FILTER_ON":null,"gcode_macro _LED_CHAMBER_FILTER_OFF":null,"gcode_macro _LED_LOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_LOADED":null,"gcode_macro _LED_FILAMENT_RUNOUT":null,"gcode_macro _LED_FILAMENT_CLOG":null,"gcode_macro _LED_UNLOADING_FILAMENT":null,"gcode_macro _LED_FILAMENT_UNLOADED":null,"gcode_macro _LED_DEACTIVATE_TOOLHEAD":null,"gcode_macro _LED_TOOLHEAD_STANDBY":null,"gcode_macro _LED_TOOLHEAD_WAKEUP":null,"gcode_macro _LED_MOTORS_OFF":null,"gcode_macro _LED_INPUT_SHAPER_START":null,"gcode_macro _LED_INPUT_SHAPER_END":null,"gcode_macro _LED_BEACON_CALIBRATION_START":null,"gcode_macro _LED_BEACON_CALIBRATION_END":null,"gcode_macro _LED_BEACON_CALIBRATION_ERROR":null,"gcode_macro _LED_VAOC_ON":null,"gcode_macro _LED_VAOC_OFF":null,"gcode_macro _LED_ACTION":null,"gcode_macro _LED_SUCCESS":null,"gcode_macro _LED_HEATING":null,"gcode_macro _LED_COOLING":null,"gcode_macro _LED_ERROR":null,"gcode_macro _LED_ON":null,"gcode_macro _LED_OFF":null,"gcode_macro _LED_STANDBY":null,"gcode_macro _LED_SET":null,"gcode_macro _USER_LED_SET":null,"gcode_macro LOAD_FILAMENT":null,"gcode_macro _DEFAULT_LOAD_FILAMENT":null,"gcode_macro _IDEX_LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT":null,"gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE":null,"gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT":null,"gcode_macro _PURGE_BEFORE_UNLOAD":null,"gcode_macro _PURGE_FILAMENT":null,"gcode_macro _MOVE_TO_PARKING_POSITION":null,"gcode_macro _MOVE_TO_LOADING_POSITION":null,"gcode_macro _CLEANING_MOVE":null,"gcode_macro _START_PRINT_BED_MESH":null,"gcode_macro CALIBRATE_ADAPTIVE_MESH":null,"gcode_macro M84":null,"gcode_macro M104":null,"gcode_macro M109":null,"gcode_macro SET_HEATER_TEMPERATURE":null,"gcode_macro TEMPERATURE_WAIT":null,"gcode_macro SET_GCODE_OFFSET":null,"gcode_macro SDCARD_PRINT_FILE":null,"gcode_macro SKEW_PROFILE":null,"gcode_macro SET_SKEW":null,"gcode_macro SET_VELOCITY_LIMIT":null,"gcode_macro _START_PRINT_PARK":null,"gcode_macro _END_PRINT_PARK":null,"gcode_macro _PARK":null,"gcode_macro SAVE_PROBE_RESULT":null,"gcode_macro PROBE_FOR_PRIMING":null,"gcode_macro RESET_PRIME_PROBE_STATE":null,"gcode_macro PROBE_CURRENT_POSITION":null,"gcode_macro PRIME_BLOB":null,"gcode_macro UNLOAD_FILAMENT":null,"gcode_macro _LEGACY_UNLOAD_FILAMENT":null,"gcode_macro _DEFAULT_UNLOAD_FILAMENT":null,"gcode_macro _IDEX_UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT":null,"gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE":null,"gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER":null,"gcode_macro _UNLOAD_WITH_TIP_FORMING":null,"gcode_macro _UNLOAD_KNOWN_FILAMENT":null,"gcode_macro _UNLOAD_UNKNOWN_FILAMENT":null,"gcode_macro _TIP_FORMING":null,"gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT":null,"gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG":null,"gcode_macro _ON_FILAMENT_END":null,"gcode_macro M600":null,"gcode_macro COLD_PULL":null,"gcode_macro _USER_START_PRINT_BEFORE_HOMING":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _USER_START_PRINT_BED_MESH":null,"gcode_macro _USER_START_PRINT_PARK":null,"gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _USER_START_PRINT_HEAT_CHAMBER":null,"gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _USER_END_PRINT_PARK":null,"gcode_macro _USER_END_PRINT_FINISHED":null,"gcode_macro _USER_START_PRINT":null,"gcode_macro _USER_END_START_PRINT":null,"gcode_macro _USER_START_FEATURE":null,"gcode_macro _USER_END_FEATURE":null,"gcode_macro ECHO_T_VARS":null,"gcode_macro ECHO_RATOS_VARS":null,"gcode_macro INITIAL_FRONTEND_UPDATE":null,"gcode_macro CALCULATE_PRINTABLE_AREA":null,"gcode_macro CACHE_TOOLHEAD_SETTINGS":null,"gcode_macro RESTORE_TOOLHEAD_SETTINGS":null,"gcode_macro SET_MACRO_TRAVEL_SETTINGS":null,"gcode_macro SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION":null,"gcode_macro VERIFY_HYBRID_INVERTED":null,"gcode_macro RATOS_ECHO":null,"gcode_macro ENABLE_DEBUG":null,"gcode_macro DISABLE_DEBUG":null,"gcode_macro DEBUG_ECHO":null,"gcode_macro START_FEATURE":null,"gcode_macro END_FEATURE":null,"gcode_macro _ON_LAYER_CHANGE":null,"gcode_macro _LEARN_MORE_CALIBRATION":null,"gcode_macro _LEARN_MORE_CHAMBER_FILTER":null,"gcode_macro _LEARN_MORE_FILAMENT":null,"gcode_macro _CONSOLE_SAVE_CONFIG":null,"gcode_macro SAVE_Z_OFFSET":null,"gcode_macro _LOAD_RATOS_SKEW_PROFILE":null,"gcode_macro M601":null,"gcode_macro PAUSE":null,"gcode_macro RESUME":null,"gcode_macro CANCEL_PRINT":null,"gcode_macro START_PRINT":null,"gcode_macro _START_PRINT_BEFORE_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED":null,"gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE":null,"gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER":null,"gcode_macro _PRIME":null,"gcode_macro END_PRINT":null,"gcode_macro _END_PRINT_BEFORE_HEATERS_OFF":null,"gcode_macro _END_PRINT_AFTER_HEATERS_OFF":null,"gcode_macro _SET_EXTRUSION_MODE":null,"gcode_macro GENERATE_SHAPER_GRAPHS":null,"gcode_macro MEASURE_COREXY_BELT_TENSION":null,"idle_timeout":null,"temperature_host raspberry_pi":null,"temperature_sensor raspberry_pi":null,"gcode_move":null,"print_stats":null,"virtual_sdcard":null,"display_status":null,"pause_resume":null,"ratos":null,"exclude_object":null,"heater_bed":null,"fan":null,"heater_fan toolhead_cooling_fan":null,"gcode_macro Z_TILT_ADJUST":null,"bed_mesh":null,"z_tilt":null,"firmware_retraction":null,"stepper_enable":null,"tmc2209 stepper_x":null,"tmc2209 stepper_x1":null,"tmc2209 stepper_y":null,"tmc2209 stepper_y1":null,"tmc2209 stepper_z":null,"tmc2209 stepper_z1":null,"tmc2209 stepper_z2":null,"tmc2209 extruder":null,"beacons":null,"mcu beacon":null,"probe":null,"temperature_sensor beacon_coil":null,"beacon":null,"gcode_macro BEACON_RATOS_CALIBRATION":null,"gcode_macro BEACON_RATOS_CALIBRATE":null,"gcode_macro BEACON_INITIAL_CALIBRATION":null,"gcode_macro BEACON_FINAL_CALIBRATION":null,"gcode_macro BEACON_POKE_TEST":null,"gcode_macro _BEACON_PROBE_POKE":null,"gcode_macro _BEACON_STORE_POKE":null,"gcode_macro _BEACON_CHECK_POKE":null,"gcode_macro _BEACON_ECHO_POKE":null,"gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET":null,"gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS":null,"gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET":null,"gcode_macro BEACON_MEASURE_GANTRY_TWIST":null,"gcode_macro _BEACON_PROBE_GANTRY_TWIST":null,"gcode_macro _BEACON_STORE_GANTRY_TWIST":null,"gcode_macro _BEACON_ECHO_GANTRY_TWIST":null,"gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH":null,"gcode_macro _BEACON_APPLY_SCAN_COMPENSATION":null,"gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION":null,"gcode_macro _BEACON_HOME_AND_ABL":null,"gcode_macro _BEACON_SAVE_MULTIPLIER":null,"gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER":null,"controller_fan controller_fan":null,"gcode_macro T0":null,"save_variables":null,"filament_switch_sensor toolhead_filament_sensor_t0":null,"gcode_button toolhead_filament_sensor_button_t0":null,"output_pin caselight":null,"motion_report":null,"query_endstops":null,"system_stats":null,"manual_probe":null,"toolhead":null,"extruder":null},"response_template":{"method":"process_status_update"}}}'
Received 70405.071286: b'{"id":4044199080,"method":"objects/query","params":{"objects":{"extruder":["can_extrude"]}}}'
Received 70432.124784: b'{"id":4079304392,"method":"gcode/script","params":{"script":"SDCARD_PRINT_FILE FILENAME=\\"3DBenchy_0.2mm_PLA_26m56s.gcode\\""}}'
Received 70505.901539: b'{"id":4044198048,"method":"gcode/script","params":{"script":"SDCARD_PRINT_FILE FILENAME=\\"3DBenchy_0.2mm_PLA_26m56s.gcode\\""}}'
Received 70902.092076: b'{"id":4044291064,"method":"pause_resume/pause","params":{}}'
Received 70909.051124: b'{"id":4044290296,"method":"pause_resume/resume","params":{}}'
Virtual sdcard (147147): 'X262.111 Y249.037 E.02954\nG1 X262.403 Y249.511 E.01858\nG1 X257.61 Y244.719 E.22615\nG1 X257.304 Y244.528 E.01205\nG1 X256.327 Y244.015 E.03682\nG1 X262.552 Y250.24 E.29376\nG1 X262.339 Y250.606 E.01413\nG1 X255.31 Y243.577 E.33169\nG1 X254.773 Y243.373 E.01917\nG1 X254.414 Y243.26 E.01254\nG1 X262.111 Y250.957 E.36319\nG1 X261.875 Y251.3 E.0139\nG1 X253.605 Y243.03 E.39026\nG1 X252.86 Y242.864 E.02547\nG1 X261.632 Y251.635 E.41391\nG1 X261.378 Y251.961 E.01377\nG1 X252.156 Y242.739 E.43517\nG1 X251.494 Y242.656 E.02228\nG1 X261.119 Y252.281 E.45419\nG1 X260.848 Y252.59 E.01369\nG1 X250.872 Y242.614 E.47077\nG1 X250.261 Y242.581 E.02043\nG1 X260.57 Y252.89 E.48647\nG1 X260.286 Y253.185 E.01367\nG1 X249.695 Y242.594 E.49979\nG1 X249.13 Y242.609 E.01885\nG1 X259.99 Y253.468 E.51246\nG1 X259.689 Y253.747 E.01367\nG1 X248.584 Y242.641 E.52406\nG1 X248.039 Y242.676 E.0182\nG1 X259.38 Y254.017 E.53515\nG1 X259.058 Y254.274 E.01375\nG1 X247.495 Y242.711 E.54567\nG1 X246.951 Y242.745 E.0182\nG1 X258.734 Y254.529 E.55605\nG1 X258.397 Y254.771 E.01384\n'
Upcoming (148171): 'G1 X246.406 Y242.78 E.56585\nG1 X245.862 Y242.815 E.0182\nG1 X258.052 Y255.005 E.57524\nG1 X257.701 Y255.233 E.01396\nG1 X245.317 Y2'
gcode state: absolute_coord=True absolute_extrude=False base_position=[0.0, 0.0, 0.03915624999584795, 86.95797000000003] last_position=[246.406, 242.78, 0.639156249995848, 103.14623] homing_position=[0.0, 0.0, 0.03915624999584795, 0.0] speed_factor=0.016666666666666666 extrude_factor=1.0 speed=200.0
MCU 'rpi' shutdown: Command request
clocksync state: mcu_freq=50000000 last_clock=3544923485065 clock_est=(70879.579 3543465646108 50015572.121) min_half_rtt=0.000045 min_rtt_time=70529.469 time_avg=70879.579(946.995) clock_avg=3543465646108.683(47364490747.753) pred_variance=16282044169.393 clock_adj=(21.322 50003931.118)
Dumping serial stats: bytes_write=420894 bytes_read=1297922 bytes_retransmit=0 bytes_invalid=0 send_seq=70116 receive_seq=70116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0
Dumping send queue 100 messages
Sent 0 70812.214894 70812.214894 6: seq: 10, get_clock
Sent 1 70813.199454 70813.199454 6: seq: 11, get_clock
Sent 2 70814.184327 70814.184327 6: seq: 12, get_clock
Sent 3 70815.169106 70815.169106 6: seq: 13, get_clock
Sent 4 70816.153757 70816.153757 6: seq: 14, get_clock
Sent 5 70817.137995 70817.137995 6: seq: 15, get_clock
Sent 6 70818.122124 70818.122124 6: seq: 16, get_clock
Sent 7 70819.106536 70819.106536 6: seq: 17, get_clock
Sent 8 70820.090657 70820.090657 6: seq: 18, get_clock
Sent 9 70821.075230 70821.075230 6: seq: 19, get_clock
Sent 10 70822.062269 70822.062269 6: seq: 1a, get_clock
Sent 11 70823.046138 70823.046138 6: seq: 1b, get_clock
Sent 12 70824.030498 70824.030498 6: seq: 1c, get_clock
Sent 13 70825.014938 70825.014938 6: seq: 1d, get_clock
Sent 14 70825.999197 70825.999197 6: seq: 1e, get_clock
Sent 15 70826.983333 70826.983333 6: seq: 1f, get_clock
Sent 16 70827.968067 70827.968067 6: seq: 10, get_clock
Sent 17 70828.952553 70828.952553 6: seq: 11, get_clock
Sent 18 70829.937071 70829.937071 6: seq: 12, get_clock
Sent 19 70830.921965 70830.921965 6: seq: 13, get_clock
Sent 20 70831.906494 70831.906494 6: seq: 14, get_clock
Sent 21 70832.891157 70832.891157 6: seq: 15, get_clock
Sent 22 70833.875268 70833.875268 6: seq: 16, get_clock
Sent 23 70834.860103 70834.860103 6: seq: 17, get_clock
Sent 24 70835.844811 70835.844811 6: seq: 18, get_clock
Sent 25 70836.828863 70836.828863 6: seq: 19, get_clock
Sent 26 70837.812964 70837.812964 6: seq: 1a, get_clock
Sent 27 70838.797078 70838.797078 6: seq: 1b, get_clock
Sent 28 70839.781782 70839.781782 6: seq: 1c, get_clock
Sent 29 70840.765928 70840.765928 6: seq: 1d, get_clock
Sent 30 70841.750723 70841.750723 6: seq: 1e, get_clock
Sent 31 70842.735485 70842.735485 6: seq: 1f, get_clock
Sent 32 70843.719684 70843.719684 6: seq: 10, get_clock
Sent 33 70844.724903 70844.724903 6: seq: 11, get_clock
Sent 34 70845.709640 70845.709640 6: seq: 12, get_clock
Sent 35 70846.694427 70846.694427 6: seq: 13, get_clock
Sent 36 70847.678598 70847.678598 6: seq: 14, get_clock
Sent 37 70848.663228 70848.663228 6: seq: 15, get_clock
Sent 38 70849.647453 70849.647453 6: seq: 16, get_clock
Sent 39 70850.631723 70850.631723 6: seq: 17, get_clock
Sent 40 70851.615849 70851.615849 6: seq: 18, get_clock
Sent 41 70852.616139 70852.616139 6: seq: 19, get_clock
Sent 42 70853.600520 70853.600520 6: seq: 1a, get_clock
Sent 43 70854.585070 70854.585070 6: seq: 1b, get_clock
Sent 44 70855.569353 70855.569353 6: seq: 1c, get_clock
Sent 45 70856.553713 70856.553713 6: seq: 1d, get_clock
Sent 46 70857.537800 70857.537800 6: seq: 1e, get_clock
Sent 47 70858.521941 70858.521941 6: seq: 1f, get_clock
Sent 48 70859.506849 70859.506849 6: seq: 10, get_clock
Sent 49 70860.491154 70860.491154 6: seq: 11, get_clock
Sent 50 70861.475724 70861.475724 6: seq: 12, get_clock
Sent 51 70862.459784 70862.459784 6: seq: 13, get_clock
Sent 52 70863.444694 70863.444694 6: seq: 14, get_clock
Sent 53 70864.428991 70864.428991 6: seq: 15, get_clock
Sent 54 70865.413172 70865.413172 6: seq: 16, get_clock
Sent 55 70866.397515 70866.397515 6: seq: 17, get_clock
Sent 56 70867.381932 70867.381932 6: seq: 18, get_clock
Sent 57 70868.366829 70868.366829 6: seq: 19, get_clock
Sent 58 70869.351162 70869.351162 6: seq: 1a, get_clock
Sent 59 70870.335566 70870.335566 6: seq: 1b, get_clock
Sent 60 70871.319693 70871.319693 6: seq: 1c, get_clock
Sent 61 70872.303993 70872.303993 6: seq: 1d, get_clock
Sent 62 70873.288786 70873.288786 6: seq: 1e, get_clock
Sent 63 70874.273127 70874.273127 6: seq: 1f, get_clock
Sent 64 70875.257949 70875.257949 6: seq: 10, get_clock
Sent 65 70876.242220 70876.242220 6: seq: 11, get_clock
Sent 66 70877.226622 70877.226622 6: seq: 12, get_clock
Sent 67 70878.210739 70878.210739 6: seq: 13, get_clock
Sent 68 70879.195103 70879.195103 6: seq: 14, get_clock
Sent 69 70880.179915 70880.179915 6: seq: 15, get_clock
Sent 70 70881.164921 70881.164921 6: seq: 16, get_clock
Sent 71 70882.149382 70882.149382 6: seq: 17, get_clock
Sent 72 70883.133947 70883.133947 6: seq: 18, get_clock
Sent 73 70884.118879 70884.118879 6: seq: 19, get_clock
Sent 74 70885.103642 70885.103642 6: seq: 1a, get_clock
Sent 75 70886.087899 70886.087899 6: seq: 1b, get_clock
Sent 76 70887.072207 70887.072207 6: seq: 1c, get_clock
Sent 77 70888.056465 70888.056465 6: seq: 1d, get_clock
Sent 78 70889.041055 70889.041055 6: seq: 1e, get_clock
Sent 79 70890.025228 70890.025228 6: seq: 1f, get_clock
Sent 80 70891.009678 70891.009678 6: seq: 10, get_clock
Sent 81 70891.994451 70891.994451 6: seq: 11, get_clock
Sent 82 70892.978649 70892.978649 6: seq: 12, get_clock
Sent 83 70893.962926 70893.962926 6: seq: 13, get_clock
Sent 84 70894.947195 70894.947195 6: seq: 14, get_clock
Sent 85 70895.931513 70895.931513 6: seq: 15, get_clock
Sent 86 70896.915681 70896.915681 6: seq: 16, get_clock
Sent 87 70897.900090 70897.900090 6: seq: 17, get_clock
Sent 88 70898.884160 70898.884160 6: seq: 18, get_clock
Sent 89 70899.868567 70899.868567 6: seq: 19, get_clock
Sent 90 70900.852914 70900.852914 6: seq: 1a, get_clock
Sent 91 70901.837654 70901.837654 6: seq: 1b, get_clock
Sent 92 70902.821659 70902.821659 6: seq: 1c, get_clock
Sent 93 70903.805856 70903.805856 6: seq: 1d, get_clock
Sent 94 70904.789991 70904.789991 6: seq: 1e, get_clock
Sent 95 70905.774871 70905.774871 6: seq: 1f, get_clock
Sent 96 70906.759070 70906.759070 6: seq: 10, get_clock
Sent 97 70907.743917 70907.743917 6: seq: 11, get_clock
Sent 98 70908.728233 70908.728233 6: seq: 12, get_clock
Sent 99 70909.593864 70909.593864 6: seq: 13, emergency_stop
Dumping receive queue 100 messages
Receive: 0 70827.968431 70827.968067 11: seq: 11, clock clock=1831141383
Receive: 1 70828.952724 70828.952553 11: seq: 12, clock clock=1880503529
Receive: 2 70829.937348 70829.937071 11: seq: 13, clock clock=1929858607
Receive: 3 70830.922288 70830.921965 11: seq: 14, clock clock=1979219304
Receive: 4 70831.875002 70830.921965 13: seq: 14, stats count=55 sum=54408 sumsq=626534
Receive: 5 70831.906714 70831.906494 11: seq: 15, clock clock=2028545993
Receive: 6 70832.891423 70832.891157 11: seq: 16, clock clock=2077874463
Receive: 7 70833.875544 70833.875268 11: seq: 17, clock clock=2127163125
Receive: 8 70834.860352 70834.860103 11: seq: 18, clock clock=2176483840
Receive: 9 70835.845127 70835.844811 11: seq: 19, clock clock=2225789752
Receive: 10 70836.829119 70836.828863 11: seq: 1a, clock clock=2275058026
Receive: 11 70836.867063 70836.828863 13: seq: 1a, stats count=56 sum=53701 sumsq=451572
Receive: 12 70837.813220 70837.812964 11: seq: 1b, clock clock=2324323535
Receive: 13 70838.797263 70838.797078 11: seq: 1c, clock clock=2373582880
Receive: 14 70839.781925 70839.781782 11: seq: 1d, clock clock=2422869074
Receive: 15 70840.766023 70840.765928 11: seq: 1e, clock clock=2472122664
Receive: 16 70841.750823 70841.750723 11: seq: 1f, clock clock=2521408300
Receive: 17 70841.961592 70841.750723 13: seq: 1f, stats count=56 sum=32731 sumsq=158255
Receive: 18 70842.735583 70842.735485 11: seq: 10, clock clock=2570689354
Receive: 19 70843.719790 70843.719684 11: seq: 11, clock clock=2619940459
Receive: 20 70844.725103 70844.724903 11: seq: 12, clock clock=2670243827
Receive: 21 70845.709901 70845.709640 11: seq: 13, clock clock=2719519463
Receive: 22 70846.694683 70846.694427 11: seq: 14, clock clock=2768793839
Receive: 23 70846.957772 70846.694427 13: seq: 14, stats count=55 sum=38430 sumsq=226663
Receive: 24 70847.678895 70847.678598 11: seq: 15, clock clock=2818039251
Receive: 25 70848.663540 70848.663228 11: seq: 16, clock clock=2867290968
Receive: 26 70849.647563 70849.647453 11: seq: 17, clock clock=2916445945
Receive: 27 70850.631864 70850.631723 11: seq: 18, clock clock=2965611225
Receive: 28 70851.615963 70851.615849 11: seq: 19, clock clock=3014773741
Receive: 29 70852.059903 70851.615849 13: seq: 19, stats count=56 sum=35777 sumsq=201320
Receive: 30 70852.616288 70852.616139 11: seq: 1a, clock clock=3064746979
Receive: 31 70853.600630 70853.600520 11: seq: 1b, clock clock=3113929510
Receive: 32 70854.585327 70854.585070 11: seq: 1c, clock clock=3163127986
Receive: 33 70855.569589 70855.569353 11: seq: 1d, clock clock=3212310306
Receive: 34 70856.553845 70856.553713 11: seq: 1e, clock clock=3261498789
Receive: 35 70857.063178 70856.553713 13: seq: 1e, stats count=55 sum=34150 sumsq=181892
Receive: 36 70857.537910 70857.537800 11: seq: 1f, clock clock=3310677177
Receive: 37 70858.522050 70858.521941 11: seq: 10, clock clock=3359861792
Receive: 38 70859.506962 70859.506849 11: seq: 11, clock clock=3409087355
Receive: 39 70860.491267 70860.491154 11: seq: 12, clock clock=3458284787
Receive: 40 70861.475937 70861.475724 11: seq: 13, clock clock=3507500368
Receive: 41 70862.065181 70861.475724 13: seq: 13, stats count=55 sum=29656 sumsq=125981
Receive: 42 70862.460009 70862.459784 11: seq: 14, clock clock=3556690128
Receive: 43 70863.444956 70863.444694 11: seq: 15, clock clock=3605924841
Receive: 44 70864.429102 70864.428991 11: seq: 16, clock clock=3655124993
Receive: 45 70865.413277 70865.413172 11: seq: 17, clock clock=3704325103
Receive: 46 70866.397624 70866.397515 11: seq: 18, clock clock=3753535417
Receive: 47 70867.166058 70866.397515 13: seq: 18, stats count=56 sum=32480 sumsq=174731
Receive: 48 70867.382052 70867.381932 11: seq: 19, clock clock=3802750805
Receive: 49 70868.366983 70868.366829 11: seq: 1a, clock clock=3851992270
Receive: 50 70869.351405 70869.351162 11: seq: 1b, clock clock=3901209039
Receive: 51 70870.335795 70870.335566 11: seq: 1c, clock clock=3950426227
Receive: 52 70871.319811 70871.319693 11: seq: 1d, clock clock=3999628861
Receive: 53 70872.166275 70871.319693 13: seq: 1d, stats count=55 sum=34169 sumsq=173495
Receive: 54 70872.304120 70872.303993 11: seq: 1e, clock clock=4048844660
Receive: 55 70873.288915 70873.288786 11: seq: 1f, clock clock=4098085568
Receive: 56 70874.273248 70874.273127 11: seq: 10, clock clock=4147303437
Receive: 57 70875.258051 70875.257949 11: seq: 11, clock clock=4196547771
Receive: 58 70876.242332 70876.242220 10: seq: 12, clock clock=4245765587
Receive: 59 70877.166004 70876.242220 13: seq: 12, stats count=55 sum=25832 sumsq=88223
Receive: 60 70877.226735 70877.226622 9: seq: 13, clock clock=23009
Receive: 61 70878.210849 70878.210739 10: seq: 14, clock clock=49233980
Receive: 62 70879.195205 70879.195103 10: seq: 15, clock clock=98457726
Receive: 63 70880.180011 70880.179915 10: seq: 16, clock clock=147704580
Receive: 64 70881.165182 70881.164921 10: seq: 17, clock clock=196967167
Receive: 65 70882.149653 70882.149382 11: seq: 18, clock clock=246197628
Receive: 66 70882.165538 70882.149382 13: seq: 18, stats count=56 sum=33733 sumsq=213318
Receive: 67 70883.134207 70883.133947 11: seq: 19, clock clock=295434285
Receive: 68 70884.119188 70884.118879 11: seq: 1a, clock clock=344691357
Receive: 69 70885.103867 70885.103642 11: seq: 1b, clock clock=393935264
Receive: 70 70886.088140 70886.087899 11: seq: 1c, clock clock=443158461
Receive: 71 70887.072491 70887.072207 11: seq: 1d, clock clock=492385795
Receive: 72 70887.264489 70887.072207 13: seq: 1d, stats count=56 sum=52281 sumsq=398556
Receive: 73 70888.056722 70888.056465 11: seq: 1e, clock clock=541607558
Receive: 74 70889.041286 70889.041055 11: seq: 1f, clock clock=590847188
Receive: 75 70890.025465 70890.025228 11: seq: 10, clock clock=640067066
Receive: 76 70891.009834 70891.009678 11: seq: 11, clock clock=689297887
Receive: 77 70891.994591 70891.994451 11: seq: 12, clock clock=738547580
Receive: 78 70892.363272 70891.994451 13: seq: 12, stats count=56 sum=40207 sumsq=239092
Receive: 79 70892.978787 70892.978649 11: seq: 13, clock clock=787769170
Receive: 80 70893.963065 70893.962926 11: seq: 14, clock clock=836995260
Receive: 81 70894.947357 70894.947195 11: seq: 15, clock clock=886222046
Receive: 82 70895.931837 70895.931513 11: seq: 16, clock clock=935453853
Receive: 83 70896.915973 70896.915681 11: seq: 17, clock clock=984676058
Receive: 84 70897.362189 70896.915681 13: seq: 17, stats count=55 sum=35905 sumsq=216140
Receive: 85 70897.900360 70897.900090 11: seq: 18, clock clock=1033906944
Receive: 86 70898.884771 70898.884160 11: seq: 19, clock clock=1083126777
Receive: 87 70899.868739 70899.868567 11: seq: 1a, clock clock=1132356266
Receive: 88 70900.853092 70900.852914 11: seq: 1b, clock clock=1181587636
Receive: 89 70901.837788 70901.837654 11: seq: 1c, clock clock=1230835976
Receive: 90 70902.460623 70901.837654 13: seq: 1c, stats count=56 sum=42473 sumsq=236423
Receive: 91 70902.821798 70902.821659 11: seq: 1d, clock clock=1280050289
Receive: 92 70903.806000 70903.805856 11: seq: 1e, clock clock=1329274439
Receive: 93 70904.790110 70904.789991 11: seq: 1f, clock clock=1378494410
Receive: 94 70905.774967 70905.774871 11: seq: 10, clock clock=1427752570
Receive: 95 70906.759434 70906.759070 11: seq: 11, clock clock=1476987245
Receive: 96 70907.459341 70906.759070 13: seq: 11, stats count=55 sum=30590 sumsq=166514
Receive: 97 70907.744055 70907.743917 11: seq: 12, clock clock=1526235734
Receive: 98 70908.728366 70908.728233 11: seq: 13, clock clock=1575465865
Receive: 99 70909.594061 70909.593864 12: seq: 14, shutdown clock=1618761190 static_string_id=Command request
MCU 'mcu' shutdown: Stepper too far in past
clocksync state: mcu_freq=180000000 last_clock=12764678028227 clock_est=(70880.824 12759536883005 179999343.199) min_half_rtt=0.000058 min_rtt_time=70783.305 time_avg=70880.824(844.196) clock_avg=12759536883005.143(151954644472.604) pred_variance=25362076.843
Dumping serial stats: bytes_write=1206012 bytes_read=8201034 bytes_retransmit=9 bytes_invalid=0 send_seq=90381 receive_seq=90381 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=23 upcoming_bytes=13583
Dumping send queue 100 messages
Sent 0 70909.121969 70909.121969 61: seq: 1b, queue_step oid=16 interval=1183 count=210 add=0, queue_step oid=18 interval=1183 count=210 add=0, queue_step oid=19 interval=1183 count=210 add=0, queue_step oid=12 interval=923 count=222 add=0, queue_step oid=15 interval=923 count=222 add=0, queue_step oid=11 interval=848 count=247 add=0, queue_step oid=9 interval=1021 count=217 add=0, queue_step oid=16 interval=1204 count=206 add=0
Sent 1 70909.122026 70909.122026 61: seq: 1c, queue_step oid=18 interval=1204 count=206 add=0, queue_step oid=19 interval=1204 count=206 add=0, queue_step oid=12 interval=937 count=234 add=0, queue_step oid=15 interval=937 count=234 add=0, queue_step oid=11 interval=861 count=254 add=0, queue_step oid=9 interval=1038 count=230 add=0, queue_step oid=16 interval=1226 count=208 add=0, queue_step oid=18 interval=1226 count=208 add=0
Sent 2 70909.122103 70909.122103 61: seq: 1d, queue_step oid=19 interval=1226 count=208 add=0, queue_step oid=12 interval=952 count=233 add=0, queue_step oid=15 interval=952 count=233 add=0, queue_step oid=11 interval=874 count=226 add=0, queue_step oid=9 interval=1056 count=222 add=0, queue_step oid=11 interval=887 count=232 add=0, queue_step oid=12 interval=967 count=212 add=0, queue_step oid=15 interval=967 count=212 add=0
Sent 3 70909.122181 70909.122181 61: seq: 1e, queue_step oid=16 interval=1249 count=202 add=0, queue_step oid=18 interval=1249 count=202 add=0, queue_step oid=19 interval=1249 count=202 add=0, queue_step oid=9 interval=1074 count=207 add=0, queue_step oid=11 interval=901 count=241 add=0, queue_step oid=12 interval=982 count=214 add=0, queue_step oid=15 interval=982 count=214 add=0, queue_step oid=16 interval=1273 count=202 add=0
Sent 4 70909.122292 70909.122292 61: seq: 1f, queue_step oid=18 interval=1273 count=202 add=0, queue_step oid=19 interval=1273 count=202 add=0, queue_step oid=9 interval=1092 count=201 add=0, queue_step oid=11 interval=915 count=209 add=0, queue_step oid=12 interval=998 count=218 add=0, queue_step oid=15 interval=998 count=218 add=0, queue_step oid=16 interval=1298 count=196 add=0, queue_step oid=18 interval=1298 count=196 add=0
Sent 5 70909.122379 70909.122379 61: seq: 10, queue_step oid=19 interval=1298 count=196 add=0, queue_step oid=9 interval=1111 count=208 add=0, queue_step oid=11 interval=929 count=221 add=0, queue_step oid=12 interval=1015 count=219 add=0, queue_step oid=15 interval=1015 count=219 add=0, queue_step oid=16 interval=1324 count=192 add=0, queue_step oid=18 interval=1324 count=192 add=0, queue_step oid=19 interval=1324 count=192 add=0
Sent 6 70909.122458 70909.122458 61: seq: 11, queue_step oid=11 interval=944 count=219 add=0, queue_step oid=9 interval=1131 count=201 add=0, queue_step oid=12 interval=1033 count=221 add=0, queue_step oid=15 interval=1033 count=221 add=0, queue_step oid=11 interval=959 count=201 add=0, queue_step oid=16 interval=1351 count=190 add=0, queue_step oid=18 interval=1351 count=190 add=0, queue_step oid=19 interval=1351 count=190 add=0
Sent 7 70909.122547 70909.122547 61: seq: 12, queue_step oid=9 interval=1152 count=204 add=0, queue_step oid=12 interval=1051 count=196 add=0, queue_step oid=15 interval=1051 count=196 add=0, queue_step oid=11 interval=974 count=199 add=0, queue_step oid=9 interval=1174 count=200 add=0, queue_step oid=12 interval=1069 count=200 add=0, queue_step oid=15 interval=1069 count=200 add=0, queue_step oid=16 interval=1379 count=181 add=0
Sent 8 70909.122595 70909.122595 61: seq: 13, queue_step oid=18 interval=1379 count=181 add=0, queue_step oid=19 interval=1379 count=181 add=0, queue_step oid=11 interval=990 count=208 add=0, queue_step oid=12 interval=1088 count=198 add=0, queue_step oid=15 interval=1088 count=198 add=0, queue_step oid=9 interval=1197 count=197 add=0, queue_step oid=16 interval=1408 count=182 add=0, queue_step oid=18 interval=1408 count=182 add=0
Sent 9 70909.122678 70909.122678 61: seq: 14, queue_step oid=19 interval=1408 count=182 add=0, queue_step oid=11 interval=1007 count=203 add=0, queue_step oid=12 interval=1108 count=198 add=0, queue_step oid=15 interval=1108 count=198 add=0, queue_step oid=9 interval=1221 count=194 add=0, queue_step oid=16 interval=1439 count=179 add=0, queue_step oid=18 interval=1439 count=179 add=0, queue_step oid=19 interval=1439 count=179 add=0
Sent 10 70909.122736 70909.122736 61: seq: 15, queue_step oid=11 interval=1025 count=210 add=0, queue_step oid=12 interval=1129 count=196 add=0, queue_step oid=15 interval=1129 count=196 add=0, queue_step oid=9 interval=1246 count=189 add=0, queue_step oid=11 interval=1044 count=204 add=0, queue_step oid=16 interval=1471 count=173 add=0, queue_step oid=18 interval=1471 count=173 add=0, queue_step oid=19 interval=1471 count=173 add=0
Sent 11 70909.122814 70909.122814 61: seq: 16, queue_step oid=12 interval=1151 count=193 add=0, queue_step oid=15 interval=1151 count=193 add=0, queue_step oid=9 interval=1272 count=186 add=0, queue_step oid=11 interval=1063 count=187 add=0, queue_step oid=16 interval=1504 count=165 add=0, queue_step oid=18 interval=1504 count=165 add=0, queue_step oid=19 interval=1504 count=165 add=0, queue_step oid=12 interval=1174 count=191 add=0
Sent 12 70909.122891 70909.122891 61: seq: 17, queue_step oid=15 interval=1174 count=191 add=0, queue_step oid=11 interval=1082 count=185 add=0, queue_step oid=9 interval=1299 count=180 add=0, queue_step oid=16 interval=1538 count=162 add=0, queue_step oid=18 interval=1538 count=162 add=0, queue_step oid=19 interval=1538 count=162 add=0, queue_step oid=12 interval=1198 count=186 add=0, queue_step oid=15 interval=1198 count=186 add=0
Sent 13 70909.122968 70909.122968 61: seq: 18, queue_step oid=11 interval=1102 count=184 add=0, queue_step oid=9 interval=1327 count=176 add=0, queue_step oid=16 interval=1574 count=160 add=0, queue_step oid=18 interval=1574 count=160 add=0, queue_step oid=19 interval=1574 count=160 add=0, queue_step oid=12 interval=1223 count=184 add=0, queue_step oid=15 interval=1223 count=184 add=0, queue_step oid=11 interval=1123 count=184 add=0
Sent 14 70909.133351 70909.133351 61: seq: 19, queue_step oid=9 interval=1356 count=170 add=0, queue_step oid=11 interval=1145 count=179 add=0, queue_step oid=12 interval=1249 count=177 add=0, queue_step oid=15 interval=1249 count=177 add=0, queue_step oid=16 interval=1612 count=157 add=0, queue_step oid=18 interval=1612 count=157 add=0, queue_step oid=19 interval=1612 count=157 add=0, queue_step oid=9 interval=1386 count=165 add=0
Sent 15 70909.133351 70909.133351 61: seq: 1a, queue_step oid=11 interval=1168 count=179 add=0, queue_step oid=12 interval=1276 count=175 add=0, queue_step oid=15 interval=1276 count=175 add=0, queue_step oid=16 interval=1652 count=154 add=0, queue_step oid=18 interval=1652 count=154 add=0, queue_step oid=19 interval=1652 count=154 add=0, queue_step oid=9 interval=1417 count=159 add=0, queue_step oid=11 interval=1192 count=173 add=0
Sent 16 70909.133351 70909.133351 61: seq: 1b, queue_step oid=12 interval=1304 count=167 add=0, queue_step oid=15 interval=1304 count=167 add=0, queue_step oid=16 interval=1694 count=149 add=0, queue_step oid=18 interval=1694 count=149 add=0, queue_step oid=19 interval=1694 count=149 add=0, queue_step oid=9 interval=1450 count=164 add=0, queue_step oid=11 interval=1217 count=172 add=0, queue_step oid=12 interval=1333 count=165 add=0
Sent 17 70909.133351 70909.133351 61: seq: 1c, queue_step oid=15 interval=1333 count=165 add=0, queue_step oid=16 interval=1738 count=144 add=0, queue_step oid=18 interval=1738 count=144 add=0, queue_step oid=19 interval=1738 count=144 add=0, queue_step oid=9 interval=1485 count=155 add=0, queue_step oid=11 interval=1243 count=164 add=0, queue_step oid=12 interval=1364 count=167 add=0, queue_step oid=15 interval=1364 count=167 add=0
Sent 18 70909.133351 70909.133351 61: seq: 1d, queue_step oid=11 interval=1270 count=164 add=0, queue_step oid=16 interval=1784 count=141 add=0, queue_step oid=18 interval=1784 count=141 add=0, queue_step oid=19 interval=1784 count=141 add=0, queue_step oid=9 interval=1521 count=149 add=0, queue_step oid=12 interval=1397 count=161 add=0, queue_step oid=15 interval=1397 count=161 add=0, queue_step oid=11 interval=1299 count=166 add=0
Sent 19 70909.133351 70909.133351 61: seq: 1e, queue_step oid=9 interval=1559 count=151 add=0, queue_step oid=16 interval=1833 count=139 add=0, queue_step oid=18 interval=1833 count=139 add=0, queue_step oid=19 interval=1833 count=139 add=0, queue_step oid=12 interval=1431 count=155 add=0, queue_step oid=15 interval=1431 count=155 add=0, queue_step oid=11 interval=1330 count=163 add=0, queue_step oid=9 interval=1599 count=142 add=0
Sent 20 70909.133351 70909.133351 61: seq: 1f, queue_step oid=16 interval=1885 count=134 add=0, queue_step oid=18 interval=1885 count=134 add=0, queue_step oid=19 interval=1885 count=134 add=0, queue_step oid=12 interval=1466 count=148 add=0, queue_step oid=15 interval=1466 count=148 add=0, queue_step oid=11 interval=1362 count=152 add=0, queue_step oid=9 interval=1641 count=142 add=0, queue_step oid=12 interval=1503 count=148 add=0
Sent 21 70909.133351 70909.133351 61: seq: 10, queue_step oid=15 interval=1503 count=148 add=0, queue_step oid=16 interval=1940 count=132 add=0, queue_step oid=18 interval=1940 count=132 add=0, queue_step oid=19 interval=1940 count=132 add=0, queue_step oid=11 interval=1395 count=153 add=0, queue_step oid=9 interval=1686 count=140 add=0, queue_step oid=12 interval=1542 count=141 add=0, queue_step oid=15 interval=1542 count=141 add=0
Sent 22 70909.133351 70909.133351 61: seq: 11, queue_step oid=16 interval=1999 count=128 add=0, queue_step oid=18 interval=1999 count=128 add=0, queue_step oid=19 interval=1999 count=128 add=0, queue_step oid=11 interval=1430 count=145 add=0, queue_step oid=9 interval=1734 count=136 add=0, queue_step oid=12 interval=1583 count=142 add=0, queue_step oid=15 interval=1583 count=142 add=0, queue_step oid=11 interval=1466 count=141 add=0
Sent 23 70909.133351 70909.133351 61: seq: 12, queue_step oid=16 interval=2061 count=123 add=0, queue_step oid=18 interval=2061 count=123 add=0, queue_step oid=19 interval=2061 count=123 add=0, queue_step oid=9 interval=1785 count=133 add=0, queue_step oid=12 interval=1627 count=137 add=0, queue_step oid=15 interval=1627 count=137 add=0, queue_step oid=11 interval=1504 count=139 add=0, queue_step oid=16 interval=2127 count=119 add=0
Sent 24 70909.133351 70909.133351 61: seq: 13, queue_step oid=18 interval=2127 count=119 add=0, queue_step oid=19 interval=2127 count=119 add=0, queue_step oid=12 interval=1673 count=131 add=0, queue_step oid=15 interval=1673 count=131 add=0, queue_step oid=9 interval=1839 count=129 add=0, queue_step oid=11 interval=1545 count=139 add=0, queue_step oid=16 interval=2197 count=115 add=0, queue_step oid=18 interval=2197 count=115 add=0
Sent 25 70909.133351 70909.133351 61: seq: 14, queue_step oid=19 interval=2197 count=115 add=0, queue_step oid=12 interval=1721 count=127 add=0, queue_step oid=15 interval=1721 count=127 add=0, queue_step oid=9 interval=1896 count=123 add=0, queue_step oid=11 interval=1588 count=131 add=0, queue_step oid=16 interval=2272 count=112 add=0, queue_step oid=18 interval=2272 count=112 add=0, queue_step oid=19 interval=2272 count=112 add=0
Sent 26 70909.133649 70909.133649 61: seq: 15, queue_step oid=12 interval=1772 count=125 add=0, queue_step oid=15 interval=1772 count=125 add=0, queue_step oid=11 interval=1633 count=129 add=0, queue_step oid=9 interval=1957 count=122 add=0, queue_step oid=16 interval=2352 count=107 add=0, queue_step oid=18 interval=2352 count=107 add=0, queue_step oid=19 interval=2352 count=107 add=0, queue_step oid=12 interval=1827 count=121 add=0
Sent 27 70909.133705 70909.133705 61: seq: 16, queue_step oid=15 interval=1827 count=121 add=0, queue_step oid=11 interval=1682 count=130 add=0, queue_step oid=9 interval=2022 count=116 add=0, queue_step oid=12 interval=1885 count=118 add=0, queue_step oid=15 interval=1885 count=118 add=0, queue_step oid=11 interval=1735 count=125 add=0, queue_step oid=16 interval=2392 count=151 add=1, queue_step oid=18 interval=2392 count=151 add=1
Sent 28 70909.133824 70909.133824 61: seq: 17, queue_step oid=19 interval=2392 count=151 add=1, queue_step oid=9 interval=2091 count=112 add=0, queue_step oid=12 interval=1947 count=113 add=0, queue_step oid=15 interval=1947 count=113 add=0, queue_step oid=11 interval=1790 count=118 add=0, queue_step oid=9 interval=2164 count=107 add=0, queue_step oid=16 interval=2527 count=220 add=1, queue_step oid=18 interval=2527 count=220 add=1
Sent 29 70909.134013 70909.134013 61: seq: 18, queue_step oid=19 interval=2527 count=220 add=1, queue_step oid=12 interval=2013 count=111 add=0, queue_step oid=15 interval=2013 count=111 add=0, queue_step oid=11 interval=1848 count=114 add=0, queue_step oid=9 interval=2243 count=106 add=0, queue_step oid=11 interval=1910 count=112 add=0, queue_step oid=12 interval=2085 count=107 add=0, queue_step oid=15 interval=2085 count=107 add=0
Sent 30 70909.134189 70909.134189 61: seq: 19, queue_step oid=9 interval=2285 count=150 add=1, queue_step oid=11 interval=1978 count=110 add=0, queue_step oid=12 interval=2119 count=111 add=1, queue_step oid=15 interval=2119 count=111 add=1, queue_step oid=16 interval=2798 count=163 add=1, queue_step oid=18 interval=2798 count=163 add=1, queue_step oid=19 interval=2798 count=163 add=1, queue_step oid=11 interval=2051 count=106 add=0
Sent 31 70909.134342 70909.134342 61: seq: 1a, queue_step oid=9 interval=2422 count=188 add=1, queue_step oid=12 interval=2197 count=354 add=1, queue_step oid=15 interval=2197 count=354 add=1, queue_step oid=11 interval=2130 count=102 add=0, queue_step oid=16 interval=3044 count=124 add=1, queue_step oid=18 interval=3044 count=124 add=1, queue_step oid=19 interval=3044 count=124 add=1, queue_step oid=11 interval=2171 count=184 add=1
Sent 32 70909.134342 70909.134342 61: seq: 1b, queue_step oid=9 interval=2661 count=158 add=1, queue_step oid=16 interval=3242 count=184 add=2, queue_step oid=18 interval=3242 count=184 add=2, queue_step oid=19 interval=3242 count=184 add=2, queue_step oid=11 interval=2349 count=133 add=1, queue_step oid=12 interval=2604 count=150 add=1, queue_step oid=15 interval=2604 count=150 add=1, queue_step oid=9 interval=2902 count=119 add=1
Sent 33 70909.134471 70909.134471 61: seq: 1c, queue_step oid=11 interval=2535 count=143 add=1, queue_step oid=12 interval=2790 count=251 add=2, queue_step oid=15 interval=2790 count=251 add=2, queue_step oid=9 interval=3097 count=171 add=2, queue_step oid=16 interval=3688 count=159 add=3, queue_step oid=18 interval=3688 count=159 add=3, queue_step oid=19 interval=3688 count=159 add=3, queue_step oid=11 interval=2713 count=246 add=2
Sent 34 70909.134749 70909.134749 61: seq: 1d, queue_step oid=9 interval=3519 count=148 add=3, queue_step oid=16 interval=4259 count=144 add=5, queue_step oid=18 interval=4259 count=144 add=5, queue_step oid=19 interval=4259 count=144 add=5, queue_step oid=12 interval=3359 count=158 add=3, queue_step oid=15 interval=3359 count=158 add=3, queue_step oid=11 interval=3273 count=152 add=3, queue_step oid=9 interval=4058 count=134 add=5
Sent 35 70909.134749 70909.134749 61: seq: 1e, queue_step oid=12 interval=3927 count=134 add=5, queue_step oid=15 interval=3927 count=134 add=5, queue_step oid=16 interval=5114 count=115 add=9, queue_step oid=18 interval=5114 count=115 add=9, queue_step oid=19 interval=5114 count=115 add=9, queue_step oid=11 interval=3821 count=129 add=5, queue_step oid=9 interval=4822 count=123 add=10, queue_step oid=12 interval=4701 count=118 add=10
Sent 36 70909.134903 70909.134903 64: seq: 1f, queue_step oid=15 interval=4701 count=118 add=10, queue_step oid=16 interval=6299 count=96 add=20, queue_step oid=18 interval=6299 count=96 add=20, queue_step oid=19 interval=6299 count=96 add=20, queue_step oid=11 interval=4564 count=115 add=10, queue_step oid=9 interval=6200 count=88 add=23, queue_step oid=12 interval=6038 count=84 add=23, queue_step oid=15 interval=6038 count=84 add=23, queue_step oid=11 interval=5866 count=82 add=23
Sent 37 70909.135088 70909.135088 61: seq: 10, queue_step oid=16 interval=8537 count=58 add=52, queue_step oid=18 interval=8537 count=58 add=52, queue_step oid=19 interval=8537 count=58 add=52, queue_step oid=9 interval=8538 count=52 add=65, queue_step oid=12 interval=8210 count=53 add=68, queue_step oid=15 interval=8210 count=53 add=68, queue_step oid=11 interval=7974 count=52 add=69, queue_step oid=16 interval=11965 count=33 add=167, queue_step oid=18 interval=11965 count=33 add=167
Sent 38 70909.135250 70909.135250 59: seq: 11, queue_step oid=19 interval=11965 count=33 add=167, queue_step oid=9 interval=12347 count=28 add=229, queue_step oid=12 interval=12403 count=25 add=244, queue_step oid=15 interval=12403 count=25 add=244, queue_step oid=11 interval=12112 count=25 add=256, queue_step oid=16 interval=18272 count=15 add=659, queue_step oid=18 interval=18272 count=15 add=659
Sent 39 70909.135370 70909.135370 61: seq: 12, queue_step oid=19 interval=18272 count=15 add=659, queue_step oid=9 interval=20315 count=11 add=959, queue_step oid=12 interval=19095 count=12 add=1158, queue_step oid=15 interval=19095 count=12 add=1158, queue_step oid=11 interval=20028 count=10 add=1187, queue_step oid=16 interval=28604 count=7 add=3385, queue_step oid=18 interval=28604 count=7 add=3385
Sent 40 70909.135370 70909.135370 63: seq: 13, queue_step oid=19 interval=28604 count=7 add=3385, queue_step oid=9 interval=33023 count=5 add=4959, queue_step oid=12 interval=39982 count=3 add=6373, queue_step oid=15 interval=39982 count=3 add=6373, queue_step oid=11 interval=34733 count=4 add=7937, queue_step oid=16 interval=63790 count=2 add=27836, queue_step oid=18 interval=63790 count=2 add=27836
Sent 41 70909.135649 70909.135649 63: seq: 14, queue_step oid=19 interval=63790 count=2 add=27836, set_next_step_dir oid=9 dir=0, queue_step oid=9 interval=239383 count=1 add=0, queue_step oid=12 interval=68845 count=1 add=0, queue_step oid=15 interval=68845 count=1 add=0, queue_step oid=11 interval=98389 count=3 add=-29594, queue_step oid=12 interval=2450906 count=1 add=0, queue_step oid=15 interval=2450906 count=1 add=0
Sent 42 70909.135896 70909.135896 58: seq: 15, queue_step oid=16 interval=1432098 count=1 add=0, queue_step oid=18 interval=1432098 count=1 add=0, queue_step oid=19 interval=1432098 count=1 add=0, queue_step oid=9 interval=35744 count=8 add=-2776, queue_step oid=11 interval=33736 count=7 add=-2876, queue_step oid=11 interval=18366 count=16 add=-527, queue_step oid=9 interval=18009 count=17 add=-485
Sent 43 70909.135896 70909.135896 64: seq: 16, queue_step oid=11 interval=10977 count=33 add=-105, queue_step oid=9 interval=10706 count=33 add=-95, queue_step oid=11 interval=8466 count=93 add=0, queue_step oid=9 interval=8465 count=92 add=0, set_next_step_dir oid=16 dir=0, queue_step oid=16 interval=3783739 count=1 add=0, set_next_step_dir oid=18 dir=0, queue_step oid=18 interval=3783739 count=1 add=0, set_next_step_dir oid=19 dir=0, queue_step oid=19 interval=3783739 count=1 add=0
Sent 44 70909.136044 70909.136044 61: seq: 17, queue_step oid=11 interval=9040 count=26 add=229, queue_step oid=9 interval=9130 count=26 add=226, queue_step oid=11 interval=15939 count=9 add=1397, queue_step oid=9 interval=16547 count=9 add=1317, queue_step oid=11 interval=31865 count=3 add=11244, queue_step oid=9 interval=34736 count=2 add=10969, set_next_step_dir oid=9 dir=1, queue_step oid=9 interval=190587 count=1 add=0
Sent 45 70909.136044 70909.136044 63: seq: 18, queue_step oid=11 interval=10090369 count=1 add=0, queue_step oid=12 interval=70542 count=3 add=-16203, queue_step oid=15 interval=70542 count=3 add=-16203, queue_step oid=9 interval=31454 count=8 add=-2565, queue_step oid=12 interval=32899 count=10 add=-1788, queue_step oid=15 interval=32899 count=10 add=-1788, queue_step oid=9 interval=15253 count=19 add=-400
Sent 46 70909.136272 70909.136272 61: seq: 19, queue_step oid=12 interval=18384 count=20 add=-393, queue_step oid=15 interval=18384 count=20 add=-393, queue_step oid=9 interval=8911 count=42 add=-86, queue_step oid=12 interval=11616 count=44 add=-99, queue_step oid=15 interval=11616 count=44 add=-99, queue_step oid=9 interval=5806 count=61 add=-29, queue_step oid=9 interval=4210 count=64 add=-6, queue_step oid=12 interval=7958 count=973 add=0
Sent 47 70909.136532 70909.136532 63: seq: 1a, queue_step oid=15 interval=7958 count=973 add=0, queue_step oid=9 interval=3978 count=1896 add=0, queue_step oid=16 interval=6847023 count=1 add=0, queue_step oid=18 interval=6847023 count=1 add=0, queue_step oid=19 interval=6847023 count=1 add=0, queue_step oid=9 interval=4148 count=70 add=21, queue_step oid=12 interval=8512 count=39 add=109, queue_step oid=15 interval=8512 count=39 add=109
Sent 48 70909.136532 70909.136532 63: seq: 1b, queue_step oid=9 interval=5901 count=41 add=67, queue_step oid=12 interval=13740 count=16 add=464, queue_step oid=15 interval=13740 count=16 add=464, queue_step oid=9 interval=9128 count=19 add=343, queue_step oid=12 interval=22386 count=7 add=2559, queue_step oid=15 interval=22386 count=7 add=2559, set_next_step_dir oid=16 dir=1, queue_step oid=16 interval=372628 count=1 add=0, set_next_step_dir oid=18 dir=1
Sent 49 70909.136532 70909.136532 58: seq: 1c, queue_step oid=18 interval=372628 count=1 add=0, set_next_step_dir oid=19 dir=1, queue_step oid=19 interval=372628 count=1 add=0, queue_step oid=9 interval=16279 count=6 add=2814, queue_step oid=12 interval=54466 count=2 add=30005, queue_step oid=15 interval=54466 count=2 add=30005, queue_step oid=9 interval=40399 count=1 add=0, set_next_step_dir oid=9 dir=0
Sent 50 70909.136659 70909.136659 56: seq: 1d, queue_step oid=9 interval=171150 count=1 add=0, queue_step oid=12 interval=147419 count=1 add=0, queue_step oid=15 interval=147419 count=1 add=0, queue_step oid=11 interval=43125 count=4 add=-6378, queue_step oid=16 interval=1148268 count=1 add=0, queue_step oid=18 interval=1148268 count=1 add=0, queue_step oid=19 interval=1148268 count=1 add=0
Sent 51 70909.136659 70909.136659 64: seq: 1e, queue_step oid=9 interval=70319 count=4 add=-11088, queue_step oid=12 interval=71111 count=4 add=-11255, queue_step oid=15 interval=71111 count=4 add=-11255, queue_step oid=11 interval=19740 count=16 add=-656, queue_step oid=9 interval=36982 count=9 add=-1977, queue_step oid=12 interval=37478 count=8 add=-2038, queue_step oid=15 interval=37478 count=8 add=-2038
Sent 52 70909.136744 70909.136744 64: seq: 1f, queue_step oid=11 interval=10385 count=35 add=-116, queue_step oid=12 interval=22300 count=37 add=-13, queue_step oid=15 interval=22300 count=37 add=-13, queue_step oid=9 interval=22573 count=20 add=-105, queue_step oid=11 interval=7298 count=96 add=0, queue_step oid=9 interval=21800 count=18 add=0, queue_step oid=16 interval=7012927 count=1 add=0, queue_step oid=18 interval=7012927 count=1 add=0
Sent 53 70909.136793 70909.136793 60: seq: 10, queue_step oid=19 interval=7012927 count=1 add=0, queue_step oid=12 interval=23672 count=9 add=1806, queue_step oid=15 interval=23672 count=9 add=1806, queue_step oid=11 interval=7766 count=27 add=203, queue_step oid=9 interval=24734 count=8 add=1804, queue_step oid=9 interval=42283 count=3 add=10973, queue_step oid=12 interval=46291 count=3 add=10740
Sent 54 70909.136893 70909.136893 64: seq: 11, queue_step oid=15 interval=46291 count=3 add=10740, queue_step oid=11 interval=14617 count=9 add=1336, queue_step oid=9 interval=93509 count=3 add=-27601, set_next_step_dir oid=12 dir=1, queue_step oid=12 interval=178793 count=1 add=0, set_next_step_dir oid=15 dir=0, queue_step oid=15 interval=178793 count=1 add=0, queue_step oid=11 interval=38703 count=1 add=0, queue_step oid=11 interval=1155068 count=1 add=0
Sent 55 70909.136943 70909.136943 62: seq: 12, queue_step oid=12 interval=48479 count=5 add=-5237, queue_step oid=15 interval=48479 count=5 add=-5237, queue_step oid=9 interval=24806 count=11 add=-1296, queue_step oid=12 interval=24657 count=16 add=-751, queue_step oid=15 interval=24657 count=16 add=-751, queue_step oid=9 interval=12355 count=29 add=-198, queue_step oid=9 interval=7293 count=54 add=-49
Sent 56 70909.137034 70909.137034 63: seq: 13, queue_step oid=12 interval=14029 count=35 add=-164, queue_step oid=15 interval=14029 count=35 add=-164, queue_step oid=9 interval=4913 count=70 add=-17, queue_step oid=12 interval=8906 count=43 add=-34, queue_step oid=15 interval=8906 count=43 add=-34, queue_step oid=11 interval=9285589 count=1 add=0, queue_step oid=9 interval=3978 count=2054 add=0, queue_step oid=12 interval=7959 count=1014 add=0
Sent 57 70909.137116 70909.137116 62: seq: 14, queue_step oid=15 interval=7959 count=1014 add=0, queue_step oid=16 interval=5522878 count=1 add=0, queue_step oid=18 interval=5522878 count=1 add=0, queue_step oid=19 interval=5522878 count=1 add=0, queue_step oid=9 interval=4172 count=69 add=21, queue_step oid=12 interval=8525 count=39 add=108, queue_step oid=15 interval=8525 count=39 add=108, queue_step oid=9 interval=5907 count=41 add=67
Sent 58 70909.137163 70909.137163 59: seq: 15, queue_step oid=12 interval=13849 count=16 add=443, queue_step oid=15 interval=13849 count=16 add=443, queue_step oid=9 interval=9156 count=19 add=343, queue_step oid=12 interval=22100 count=7 add=2698, queue_step oid=15 interval=22100 count=7 add=2698, queue_step oid=9 interval=16452 count=6 add=2833, queue_step oid=12 interval=54553 count=1 add=0
Sent 59 70909.137291 70909.137291 58: seq: 16, queue_step oid=15 interval=54553 count=1 add=0, set_next_step_dir oid=12 dir=0, queue_step oid=12 interval=2324532 count=1 add=0, set_next_step_dir oid=15 dir=1, queue_step oid=15 interval=2324532 count=1 add=0, queue_step oid=9 interval=39280 count=6 add=-3693, queue_step oid=11 interval=32629 count=9 add=-2153, queue_step oid=9 interval=19177 count=20 add=-489
Sent 60 70909.171112 70909.171112 64: seq: 17, tmcuart_send oid=6 write=b'\xea\x03\xe8\xad\xe1' read=10, queue_step oid=11 interval=16684 count=21 add=-377, queue_step oid=9 interval=10860 count=31 add=-112, queue_step oid=11 interval=10082 count=30 add=-85, queue_step oid=9 interval=8425 count=94 add=0, queue_step oid=11 interval=8426 count=90 add=0, queue_step oid=16 interval=12617904 count=1 add=0, queue_step oid=18 interval=12617904 count=1 add=0
Sent 61 70909.175681 70909.175681 22: seq: 18, tmcuart_send oid=7 write=b'\xea\x03\xe8\xad\xe1' read=10, queue_step oid=19 interval=12617904 count=1 add=0
Sent 62 70909.179996 70909.179996 14: seq: 19, tmcuart_send oid=8 write=b'\xea\x03\xe8\xad\xe1' read=10
Sent 63 70909.184368 70909.184368 14: seq: 1a, tmcuart_send oid=6 write=b'\xea\x03( \xc3' read=10
Sent 64 70909.188694 70909.188694 14: seq: 1b, tmcuart_send oid=7 write=b'\xea\x03( \xc3' read=10
Sent 65 70909.193041 70909.193041 14: seq: 1c, tmcuart_send oid=8 write=b'\xea\x03( \xc3' read=10
Sent 66 70909.385615 70909.385615 6: seq: 1d, get_clock
Sent 67 70909.431716 70909.431716 14: seq: 1e, tmcuart_send oid=2 write=b'\xea\x03\xe8\xad\xe1' read=10
Sent 68 70909.436018 70909.436018 14: seq: 1f, tmcuart_send oid=2 write=b'\xea\x03( \xc3' read=10
Sent 69 70909.536107 70909.536107 62: seq: 10, queue_step oid=11 interval=9066 count=26 add=223, queue_step oid=9 interval=9175 count=26 add=218, queue_step oid=11 interval=15776 count=9 add=1372, queue_step oid=9 interval=16625 count=9 add=1221, queue_step oid=11 interval=30415 count=3 add=10772, queue_step oid=9 interval=33024 count=3 add=11056, queue_step oid=11 interval=8436290 count=1 add=0, set_next_step_dir oid=9 dir=1
Sent 70 70909.537430 70909.537430 63: seq: 11, queue_step oid=9 interval=105047 count=1 add=0, queue_step oid=9 interval=43606 count=4 add=-7001, queue_step oid=12 interval=70535 count=3 add=-16199, queue_step oid=15 interval=70535 count=3 add=-16199, queue_step oid=9 interval=19663 count=15 add=-697, queue_step oid=12 interval=32894 count=10 add=-1787, queue_step oid=15 interval=32894 count=10 add=-1787
Sent 71 70909.539753 70909.539753 62: seq: 12, queue_step oid=9 interval=10321 count=39 add=-118, queue_step oid=12 interval=18346 count=20 add=-387, queue_step oid=15 interval=18346 count=20 add=-387, queue_step oid=9 interval=6356 count=56 add=-37, queue_step oid=12 interval=11526 count=46 add=-94, queue_step oid=15 interval=11526 count=46 add=-94, queue_step oid=9 interval=4552 count=58 add=-14, queue_step oid=12 interval=7957 count=1062 add=0
Sent 72 70909.542314 70909.542314 61: seq: 13, queue_step oid=15 interval=7957 count=1062 add=0, queue_step oid=9 interval=3978 count=2101 add=0, queue_step oid=11 interval=2454494 count=1 add=0, queue_step oid=9 interval=4153 count=69 add=21, queue_step oid=12 interval=8398 count=40 add=115, queue_step oid=15 interval=8398 count=40 add=115, queue_step oid=9 interval=5802 count=43 add=70, queue_step oid=12 interval=13858 count=16 add=510
Sent 73 70909.545650 70909.545650 62: seq: 14, queue_step oid=15 interval=13858 count=16 add=510, queue_step oid=9 interval=9471 count=18 add=354, queue_step oid=12 interval=23157 count=6 add=3250, queue_step oid=15 interval=23157 count=6 add=3250, queue_step oid=9 interval=16582 count=6 add=2944, queue_step oid=12 interval=48478 count=2 add=29029, queue_step oid=15 interval=48478 count=2 add=29029
Sent 74 70909.548986 70909.548986 62: seq: 15, queue_step oid=9 interval=44882 count=1 add=0, set_next_step_dir oid=12 dir=1, queue_step oid=12 interval=2326600 count=1 add=0, set_next_step_dir oid=15 dir=0, queue_step oid=15 interval=2326600 count=1 add=0, set_next_step_dir oid=9 dir=0, queue_step oid=9 interval=128258 count=1 add=0, queue_step oid=9 interval=48290 count=4 add=-7058, queue_step oid=11 interval=43524 count=5 add=-5125
Sent 75 70909.552324 70909.552324 58: seq: 16, queue_step oid=9 interval=23083 count=15 add=-822, queue_step oid=11 interval=21054 count=17 add=-646, queue_step oid=9 interval=12606 count=31 add=-169, queue_step oid=11 interval=11790 count=31 add=-143, queue_step oid=9 interval=8409 count=102 add=0, queue_step oid=11 interval=8408 count=98 add=0, queue_step oid=16 interval=12949149 count=1 add=0
Sent 76 70909.555657 70909.555657 59: seq: 17, queue_step oid=18 interval=12949149 count=1 add=0, queue_step oid=19 interval=12949149 count=1 add=0, queue_step oid=11 interval=8977 count=26 add=224, queue_step oid=9 interval=9276 count=25 add=212, queue_step oid=9 interval=15410 count=10 add=1267, queue_step oid=11 interval=15243 count=10 add=1379, queue_step oid=9 interval=34832 count=2 add=10501
Sent 77 70909.558985 70909.558985 62: seq: 18, queue_step oid=11 interval=39240 count=1 add=0, queue_step oid=11 interval=10720319 count=1 add=0, queue_step oid=9 interval=28717 count=9 add=-2023, queue_step oid=12 interval=47140 count=6 add=-4809, queue_step oid=15 interval=47140 count=6 add=-4809, queue_step oid=9 interval=14480 count=19 add=-364, queue_step oid=12 interval=24303 count=13 add=-843
Sent 78 70909.563401 70909.563401 63: seq: 19, queue_step oid=15 interval=24303 count=13 add=-843, queue_step oid=9 interval=8654 count=44 add=-78, queue_step oid=12 interval=14503 count=35 add=-175, queue_step oid=15 interval=14503 count=35 add=-175, queue_step oid=9 interval=5617 count=70 add=-25, queue_step oid=12 interval=9110 count=41 add=-42, queue_step oid=15 interval=9110 count=41 add=-42, queue_step oid=9 interval=4044 count=129 add=-1
Sent 79 70909.565702 70909.565702 60: seq: 1a, queue_step oid=12 interval=7957 count=1046 add=0, queue_step oid=15 interval=7957 count=1046 add=0, queue_step oid=9 interval=3978 count=2002 add=0, queue_step oid=9 interval=4141 count=70 add=21, queue_step oid=12 interval=8414 count=40 add=114, queue_step oid=15 interval=8414 count=40 add=114, queue_step oid=9 interval=5847 count=42 add=69, queue_step oid=12 interval=14050 count=16 add=477
Sent 80 70909.568112 70909.568112 61: seq: 1b, queue_step oid=15 interval=14050 count=16 add=477, queue_step oid=9 interval=9324 count=19 add=346, queue_step oid=12 interval=24139 count=6 add=2847, queue_step oid=15 interval=24139 count=6 add=2847, queue_step oid=9 interval=18425 count=6 add=2675, queue_step oid=12 interval=52162 count=1 add=0, queue_step oid=15 interval=52162 count=1 add=0, set_next_step_dir oid=12 dir=0
Sent 81 70909.569454 70909.569454 57: seq: 1c, queue_step oid=12 interval=240562 count=1 add=0, set_next_step_dir oid=15 dir=1, queue_step oid=15 interval=240562 count=1 add=0, set_next_step_dir oid=9 dir=1, queue_step oid=9 interval=193184 count=1 add=0, queue_step oid=11 interval=51146 count=4 add=-9035, queue_step oid=9 interval=40760 count=6 add=-3854, queue_step oid=12 interval=37442 count=7 add=-3203
Sent 82 70909.570837 70909.570837 60: seq: 1d, queue_step oid=15 interval=37442 count=7 add=-3203, queue_step oid=11 interval=24066 count=11 add=-1120, queue_step oid=9 interval=20108 count=19 add=-527, queue_step oid=12 interval=18487 count=19 add=-470, queue_step oid=15 interval=18487 count=19 add=-470, queue_step oid=11 interval=13256 count=31 add=-192, queue_step oid=12 interval=10628 count=31 add=-89
Sent 83 70909.573361 70909.573361 60: seq: 1e, queue_step oid=15 interval=10628 count=31 add=-89, queue_step oid=9 interval=11405 count=28 add=-102, queue_step oid=11 interval=8111 count=106 add=0, queue_step oid=12 interval=8772 count=83 add=0, queue_step oid=15 interval=8772 count=83 add=0, queue_step oid=9 interval=9538 count=76 add=0, queue_step oid=16 interval=3729646 count=1 add=0, queue_step oid=18 interval=3729646 count=1 add=0
Sent 84 70909.574883 70909.574883 57: seq: 1f, queue_step oid=19 interval=3729646 count=1 add=0, queue_step oid=11 interval=8870 count=26 add=211, queue_step oid=12 interval=9632 count=24 add=247, queue_step oid=15 interval=9632 count=24 add=247, queue_step oid=9 interval=10654 count=21 add=279, queue_step oid=9 interval=17538 count=8 add=1743, queue_step oid=11 interval=16059 count=9 add=1222
Sent 85 70909.575705 70909.575705 56: seq: 10, tmcuart_send oid=3 write=b'\xea\x03\xe8\xad\xe1' read=10, queue_step oid=12 interval=17736 count=8 add=1373, queue_step oid=15 interval=17736 count=8 add=1373, queue_step oid=9 interval=36826 count=3 add=4993, queue_step oid=12 interval=32917 count=3 add=13956, queue_step oid=15 interval=32917 count=3 add=13956
Sent 86 70909.577441 70909.577441 63: seq: 11, queue_step oid=11 interval=33100 count=2 add=10344, queue_step oid=11 interval=9335982 count=1 add=0, queue_step oid=9 interval=26177 count=10 add=-1514, queue_step oid=12 interval=46345 count=5 add=-4755, queue_step oid=15 interval=46345 count=5 add=-4755, queue_step oid=9 interval=12893 count=28 add=-221, queue_step oid=12 interval=24107 count=17 add=-696
Sent 87 70909.578533 70909.578533 61: seq: 12, queue_step oid=15 interval=24107 count=17 add=-696, queue_step oid=9 interval=7559 count=49 add=-56, queue_step oid=12 interval=13760 count=35 add=-159, queue_step oid=15 interval=13760 count=35 add=-159, queue_step oid=9 interval=5108 count=74 add=-19, queue_step oid=12 interval=8833 count=43 add=-32, queue_step oid=15 interval=8833 count=43 add=-32, queue_step oid=9 interval=3978 count=1760 add=0
Sent 88 70909.579461 70909.579461 63: seq: 13, queue_step oid=12 interval=7959 count=866 add=0, queue_step oid=15 interval=7959 count=866 add=0, queue_step oid=16 interval=7065657 count=1 add=0, queue_step oid=18 interval=7065657 count=1 add=0, queue_step oid=19 interval=7065657 count=1 add=0, queue_step oid=9 interval=4137 count=70 add=21, queue_step oid=12 interval=8636 count=37 add=107, queue_step oid=15 interval=8636 count=37 add=107
Sent 89 70909.580559 70909.580559 58: seq: 14, queue_step oid=9 interval=5817 count=43 add=70, queue_step oid=12 interval=13085 count=18 add=479, queue_step oid=15 interval=13085 count=18 add=479, queue_step oid=9 interval=9659 count=18 add=337, queue_step oid=12 interval=24041 count=6 add=2904, queue_step oid=15 interval=24041 count=6 add=2904, queue_step oid=9 interval=18004 count=6 add=2573
Sent 90 70909.581212 70909.581212 64: seq: 15, tmcuart_send oid=4 write=b'\xea\x03\xe8\xad\xe1' read=10, queue_step oid=12 interval=49332 count=2 add=28181, queue_step oid=15 interval=49332 count=2 add=28181, set_next_step_dir oid=9 dir=0, queue_step oid=9 interval=211288 count=1 add=0, set_next_step_dir oid=12 dir=1, queue_step oid=12 interval=2326588 count=1 add=0, set_next_step_dir oid=15 dir=0, queue_step oid=15 interval=2326588 count=1 add=0
Sent 91 70909.582351 70909.582351 60: seq: 16, queue_step oid=11 interval=47300 count=5 add=-6542, queue_step oid=9 interval=36213 count=7 add=-2880, queue_step oid=11 interval=23156 count=11 add=-1039, queue_step oid=9 interval=17829 count=22 add=-399, queue_step oid=11 interval=13390 count=31 add=-190, queue_step oid=16 interval=922828 count=1 add=0, queue_step oid=18 interval=922828 count=1 add=0
Sent 92 70909.584073 70909.584073 57: seq: 17, queue_step oid=19 interval=922828 count=1 add=0, queue_step oid=9 interval=10130 count=33 add=-79, queue_step oid=11 interval=8409 count=105 add=0, queue_step oid=9 interval=8424 count=89 add=0, set_next_step_dir oid=16 dir=0, queue_step oid=16 interval=4097441 count=1 add=0, set_next_step_dir oid=18 dir=0, queue_step oid=18 interval=4097441 count=1 add=0, set_next_step_dir oid=19 dir=0
Sent 93 70909.585162 70909.585162 58: seq: 18, queue_step oid=19 interval=4097441 count=1 add=0, queue_step oid=9 interval=9158 count=26 add=219, queue_step oid=11 interval=9342 count=25 add=206, queue_step oid=11 interval=15773 count=10 add=1194, queue_step oid=9 interval=16470 count=9 add=1254, queue_step oid=9 interval=34455 count=3 add=3141, queue_step oid=11 interval=38655 count=2 add=0
Sent 94 70909.585681 70909.585681 63: seq: 19, queue_step oid=11 interval=7821597 count=1 add=0, queue_step oid=9 interval=24254 count=12 add=-1215, queue_step oid=12 interval=47141 count=6 add=-4809, queue_step oid=15 interval=47141 count=6 add=-4809, queue_step oid=9 interval=12375 count=25 add=-223, queue_step oid=12 interval=24316 count=13 add=-846, queue_step oid=15 interval=24316 count=13 add=-846
Sent 95 70909.586887 70909.586887 62: seq: 1a, queue_step oid=9 interval=7549 count=52 add=-54, queue_step oid=12 interval=14519 count=35 add=-176, queue_step oid=15 interval=14519 count=35 add=-176, queue_step oid=9 interval=5062 count=71 add=-19, queue_step oid=12 interval=9142 count=40 add=-44, queue_step oid=15 interval=9142 count=40 add=-44, queue_step oid=9 interval=3978 count=1381 add=0, queue_step oid=12 interval=7960 count=682 add=0
Sent 96 70909.587295 70909.587295 54: seq: 1b, tmcuart_send oid=5 write=b'\xea\x03\xe8\xad\xe1' read=10, queue_step oid=15 interval=7960 count=682 add=0, set_next_step_dir oid=16 dir=1, queue_step oid=16 interval=5562355 count=1 add=0, set_next_step_dir oid=18 dir=1, queue_step oid=18 interval=5562355 count=1 add=0, set_next_step_dir oid=19 dir=1, queue_step oid=19 interval=5562355 count=1 add=0
Sent 97 70909.588506 70909.588506 62: seq: 1c, queue_step oid=9 interval=4129 count=71 add=21, queue_step oid=12 interval=8449 count=39 add=115, queue_step oid=15 interval=8449 count=39 add=115, queue_step oid=9 interval=5905 count=41 add=67, queue_step oid=12 interval=13452 count=17 add=526, queue_step oid=15 interval=13452 count=17 add=526, queue_step oid=9 interval=9154 count=19 add=341, queue_step oid=12 interval=24454 count=6 add=3297
Sent 98 70909.589843 70909.589843 62: seq: 1d, queue_step oid=15 interval=24454 count=6 add=3297, queue_step oid=9 interval=16472 count=6 add=2780, queue_step oid=12 interval=60552 count=1 add=0, queue_step oid=15 interval=60552 count=1 add=0, queue_step oid=9 interval=41217 count=1 add=0, set_next_step_dir oid=12 dir=0, queue_step oid=12 interval=193244 count=1 add=0, set_next_step_dir oid=15 dir=1, queue_step oid=15 interval=193244 count=1 add=0
Sent 99 70909.591247 70909.591247 59: seq: 1e, set_next_step_dir oid=9 dir=1, queue_step oid=9 interval=151085 count=1 add=0, queue_step oid=9 interval=44211 count=5 add=-5367, queue_step oid=12 interval=43522 count=5 add=-5124, queue_step oid=15 interval=43522 count=5 add=-5124, queue_step oid=11 interval=42854 count=5 add=-4888, queue_step oid=9 interval=21249 count=16 add=-670
Dumping receive queue 100 messages
Receive: 0 70905.113658 70905.109690 19: seq: 17, tmcuart_response oid=6 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 1 70905.117961 70905.114040 19: seq: 18, tmcuart_response oid=7 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 2 70905.122272 70905.118341 19: seq: 19, tmcuart_response oid=8 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 3 70905.215014 70905.118341 14: seq: 19, analog_in_state oid=20 next_clock=3632163584 value=7669
Receive: 4 70905.225021 70905.118341 15: seq: 19, analog_in_state oid=21 next_clock=3633963584 value=28382
Receive: 5 70905.432413 70905.428399 19: seq: 1a, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 6 70905.436787 70905.432811 19: seq: 1b, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 7 70905.447420 70905.447279 11: seq: 1c, clock clock=3621289535
Receive: 8 70905.515013 70905.447279 14: seq: 1c, analog_in_state oid=20 next_clock=3686163584 value=7668
Receive: 9 70905.524994 70905.447279 15: seq: 1c, analog_in_state oid=21 next_clock=3687963584 value=28376
Receive: 10 70905.578059 70905.574166 19: seq: 1d, tmcuart_response oid=3 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 11 70905.582522 70905.578565 19: seq: 1e, tmcuart_response oid=4 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 12 70905.586844 70905.582926 19: seq: 1f, tmcuart_response oid=5 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 13 70905.591273 70905.587271 19: seq: 10, tmcuart_response oid=3 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 14 70905.595636 70905.591671 19: seq: 11, tmcuart_response oid=4 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 15 70905.599873 70905.595995 19: seq: 12, tmcuart_response oid=5 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 16 70905.815027 70905.595995 14: seq: 12, analog_in_state oid=20 next_clock=3740163584 value=7672
Receive: 17 70905.824990 70905.595995 15: seq: 12, analog_in_state oid=21 next_clock=3741963584 value=28383
Receive: 18 70906.102265 70906.096577 19: seq: 13, tmcuart_response oid=6 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 19 70906.108598 70906.102933 19: seq: 14, tmcuart_response oid=7 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 20 70906.114380 70906.109042 19: seq: 15, tmcuart_response oid=8 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 21 70906.115881 70906.109042 14: seq: 15, analog_in_state oid=20 next_clock=3794163584 value=7676
Receive: 22 70906.120292 70906.114825 19: seq: 16, tmcuart_response oid=6 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 23 70906.126230 70906.120698 15: seq: 17, analog_in_state oid=21 next_clock=3795963584 value=28399
Receive: 24 70906.126240 70906.120698 19: seq: 17, tmcuart_response oid=7 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 25 70906.141427 70906.133408 19: seq: 1d, tmcuart_response oid=8 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 26 70906.415091 70906.177513 14: seq: 1e, analog_in_state oid=20 next_clock=3848163584 value=7680
Receive: 27 70906.425090 70906.177513 15: seq: 1e, analog_in_state oid=21 next_clock=3849963584 value=28384
Receive: 28 70906.432152 70906.431916 11: seq: 10, clock clock=3798528207
Receive: 29 70906.433684 70906.431916 19: seq: 10, tmcuart_response oid=2 read=b'\n\xfa\xef-\x808\x02\x08 \xbb'
Receive: 30 70906.438685 70906.434693 19: seq: 11, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 31 70906.578599 70906.574589 19: seq: 12, tmcuart_response oid=3 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 32 70906.583537 70906.579548 19: seq: 13, tmcuart_response oid=4 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 33 70906.588383 70906.584394 19: seq: 14, tmcuart_response oid=5 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 34 70906.593315 70906.589319 19: seq: 15, tmcuart_response oid=3 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 35 70906.598149 70906.594155 19: seq: 16, tmcuart_response oid=4 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 36 70906.602985 70906.598990 19: seq: 17, tmcuart_response oid=5 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 37 70906.715088 70906.598990 14: seq: 17, analog_in_state oid=20 next_clock=3902163584 value=7676
Receive: 38 70906.725119 70906.598990 15: seq: 17, analog_in_state oid=21 next_clock=3903963584 value=28384
Receive: 39 70907.015121 70906.598990 14: seq: 17, analog_in_state oid=20 next_clock=3956163584 value=7671
Receive: 40 70907.025088 70906.598990 15: seq: 17, analog_in_state oid=21 next_clock=3957963584 value=28383
Receive: 41 70907.101168 70907.097137 19: seq: 18, tmcuart_response oid=6 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 42 70907.106373 70907.102326 19: seq: 19, tmcuart_response oid=7 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 43 70907.111497 70907.107493 19: seq: 1a, tmcuart_response oid=8 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 44 70907.116592 70907.112595 19: seq: 1b, tmcuart_response oid=6 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 45 70907.121592 70907.117569 19: seq: 1c, tmcuart_response oid=7 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 46 70907.126566 70907.122557 19: seq: 1d, tmcuart_response oid=8 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 47 70907.315141 70907.122557 14: seq: 1d, analog_in_state oid=20 next_clock=4010163584 value=7671
Receive: 48 70907.325114 70907.122557 15: seq: 1d, analog_in_state oid=21 next_clock=4011963584 value=28384
Receive: 49 70907.416973 70907.416663 11: seq: 1e, clock clock=3975786098
Receive: 50 70907.434810 70907.430768 19: seq: 1f, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 51 70907.439879 70907.435863 19: seq: 10, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 52 70907.579157 70907.575125 19: seq: 11, tmcuart_response oid=3 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 53 70907.584158 70907.580149 19: seq: 12, tmcuart_response oid=4 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 54 70907.591617 70907.585073 19: seq: 13, tmcuart_response oid=5 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 55 70907.598486 70907.594360 19: seq: 14, tmcuart_response oid=3 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 56 70907.604108 70907.599986 19: seq: 15, tmcuart_response oid=4 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 57 70907.610053 70907.605958 19: seq: 16, tmcuart_response oid=5 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 58 70907.615184 70907.605958 14: seq: 16, analog_in_state oid=20 next_clock=4064163584 value=7671
Receive: 59 70907.625154 70907.605958 15: seq: 16, analog_in_state oid=21 next_clock=4065963584 value=28386
Receive: 60 70907.915037 70907.605958 14: seq: 16, analog_in_state oid=20 next_clock=4118163584 value=7672
Receive: 61 70907.925009 70907.605958 15: seq: 16, analog_in_state oid=21 next_clock=4119963584 value=28388
Receive: 62 70908.098240 70908.098026 17: seq: 17, stats count=723 sum=4407088 sumsq=970493702
Receive: 63 70908.102011 70908.098026 19: seq: 17, tmcuart_response oid=6 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 64 70908.106431 70908.102482 19: seq: 18, tmcuart_response oid=7 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 65 70908.110891 70908.106945 19: seq: 19, tmcuart_response oid=8 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 66 70908.115316 70908.111382 19: seq: 1a, tmcuart_response oid=6 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 67 70908.119651 70908.115734 19: seq: 1b, tmcuart_response oid=7 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 68 70908.124000 70908.120073 19: seq: 1c, tmcuart_response oid=8 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 69 70908.215045 70908.120073 14: seq: 1c, analog_in_state oid=20 next_clock=4172163584 value=7667
Receive: 70 70908.225054 70908.120073 15: seq: 1c, analog_in_state oid=21 next_clock=4173963584 value=28387
Receive: 71 70908.401019 70908.400843 11: seq: 1d, clock clock=4152933214
Receive: 72 70908.434880 70908.430944 19: seq: 1e, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 73 70908.439209 70908.435263 19: seq: 1f, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 74 70908.515033 70908.435263 14: seq: 1f, analog_in_state oid=20 next_clock=4226163584 value=7669
Receive: 75 70908.525014 70908.435263 14: seq: 1f, analog_in_state oid=21 next_clock=4227963584 value=28387
Receive: 76 70908.579066 70908.575065 19: seq: 10, tmcuart_response oid=3 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 77 70908.583402 70908.579475 19: seq: 11, tmcuart_response oid=4 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 78 70908.587745 70908.583823 19: seq: 12, tmcuart_response oid=5 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 79 70908.592089 70908.588160 19: seq: 13, tmcuart_response oid=3 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 80 70908.596377 70908.592459 19: seq: 14, tmcuart_response oid=4 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 81 70908.600651 70908.596740 19: seq: 15, tmcuart_response oid=5 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 82 70908.815017 70908.596740 13: seq: 15, analog_in_state oid=20 next_clock=4280163584 value=7666
Receive: 83 70908.825005 70908.596740 14: seq: 15, analog_in_state oid=21 next_clock=4281963584 value=28387
Receive: 84 70909.115087 70908.596740 13: seq: 15, analog_in_state oid=20 next_clock=39196288 value=7669
Receive: 85 70909.125011 70909.122968 14: seq: 19, analog_in_state oid=21 next_clock=40996288 value=28385
Receive: 86 70909.175131 70909.171112 19: seq: 18, tmcuart_response oid=6 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 87 70909.179616 70909.175681 19: seq: 19, tmcuart_response oid=7 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 88 70909.183921 70909.179996 19: seq: 1a, tmcuart_response oid=8 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 89 70909.188319 70909.184368 19: seq: 1b, tmcuart_response oid=6 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 90 70909.192618 70909.188694 19: seq: 1c, tmcuart_response oid=7 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 91 70909.196962 70909.193041 19: seq: 1d, tmcuart_response oid=8 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 92 70909.385789 70909.385615 10: seq: 1e, clock clock=35224515
Receive: 93 70909.415037 70909.385615 13: seq: 1e, analog_in_state oid=20 next_clock=93196288 value=7669
Receive: 94 70909.424997 70909.385615 14: seq: 1e, analog_in_state oid=21 next_clock=94996288 value=28384
Receive: 95 70909.435640 70909.431716 19: seq: 1f, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc08\x02\x08 \xb0'
Receive: 96 70909.439924 70909.436018 19: seq: 10, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 97 70909.580780 70909.578533 19: seq: 13, tmcuart_response oid=3 read=b'\n\xfa\xef-\x808\x02\x08 \xbb'
Receive: 98 70909.586894 70909.585162 19: seq: 19, tmcuart_response oid=4 read=b'\n\xfa\xef-\x808\x02\x08 \xbb'
Receive: 99 70909.588514 70909.587295 11: seq: 1c, shutdown clock=71698883 static_string_id=Stepper too far in past
MCU 'toolboard_t0' shutdown: Command request
clocksync state: mcu_freq=64000000 last_clock=4538619026640 clock_est=(70880.824 4536791081827 63999348.670) min_half_rtt=0.000070 min_rtt_time=70477.118 time_avg=70880.824(844.100) clock_avg=4536791081827.707(54021874269.286) pred_variance=6660839.793 clock_adj=(-1.553 63999540.932)
Dumping serial stats: bytes_write=554479 bytes_read=7766122 bytes_retransmit=9 bytes_invalid=0 send_seq=74206 receive_seq=74206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0
Dumping send queue 100 messages
Sent 0 70906.749058 70906.749058 14: seq: 1a, tmcuart_send oid=2 write=b'\xea\x03( \xc3' read=10
Sent 1 70907.133101 70907.133101 15: seq: 1b, queue_digital_out oid=11 clock=3005270864 on_ticks=1544635
Sent 2 70907.416913 70907.416913 17: seq: 1c, get_clock, queue_digital_out oid=11 clock=3024470864 on_ticks=3364815
Sent 3 70907.733150 70907.733150 16: seq: 1d, queue_digital_out oid=11 clock=3043670864 on_ticks=4538051
Sent 4 70907.743625 70907.743625 14: seq: 1e, tmcuart_send oid=2 write=b'\xea\x03\xe8\xad\xe1' read=10
Sent 5 70907.748482 70907.748482 14: seq: 1f, tmcuart_send oid=2 write=b'\xea\x03( \xc3' read=10
Sent 6 70908.033033 70908.033033 16: seq: 10, queue_digital_out oid=11 clock=3062870866 on_ticks=5069949
Sent 7 70908.332969 70908.332969 16: seq: 11, queue_digital_out oid=11 clock=3082070866 on_ticks=4190413
Sent 8 70908.400955 70908.400955 6: seq: 12, get_clock
Sent 9 70908.632910 70908.632910 16: seq: 13, queue_digital_out oid=11 clock=3101270866 on_ticks=2834306
Sent 10 70908.743927 70908.743927 14: seq: 14, tmcuart_send oid=2 write=b'\xea\x03\xe8\xad\xe1' read=10
Sent 11 70908.748492 70908.748492 14: seq: 15, tmcuart_send oid=2 write=b'\xea\x03( \xc3' read=10
Sent 12 70908.932855 70908.932855 15: seq: 16, queue_digital_out oid=11 clock=3120470852 on_ticks=1192075
Sent 13 70909.059010 70909.059010 13: seq: 17, queue_digital_out oid=7 clock=3128240058 on_ticks=0
Sent 14 70909.123956 70909.123956 64: seq: 18, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=314352840 count=1 add=0, queue_step oid=5 interval=207930 count=1 add=0, queue_step oid=5 interval=69913 count=2 add=-20840, queue_step oid=5 interval=35781 count=4 add=-4132, queue_step oid=5 interval=19981 count=9 add=-1038, queue_step oid=5 interval=11266 count=18 add=-289, queue_step oid=5 interval=6703 count=28 add=-97
Sent 15 70909.123956 70909.123956 64: seq: 19, queue_step oid=5 interval=4342 count=46 add=-35, queue_step oid=5 interval=2930 count=67 add=-14, queue_step oid=5 interval=2085 count=96 add=-6, queue_step oid=5 interval=1567 count=115 add=-3, queue_step oid=5 interval=1271 count=98 add=-2, queue_step oid=5 interval=1099 count=103 add=-1, queue_step oid=5 interval=991 count=73 add=-1, queue_step oid=5 interval=950 count=93 add=-1, queue_step oid=5 interval=895 count=76 add=-1
Sent 16 70909.123956 70909.123956 64: seq: 1a, queue_step oid=5 interval=860 count=71 add=-1, queue_step oid=5 interval=833 count=67 add=-1, queue_step oid=5 interval=811 count=64 add=-1, queue_step oid=5 interval=768 count=63 add=0, queue_step oid=5 interval=742 count=117 add=0, queue_step oid=5 interval=720 count=128 add=0, queue_step oid=5 interval=702 count=138 add=0, queue_step oid=5 interval=687 count=172 add=0, queue_step oid=5 interval=675 count=207 add=0
Sent 17 70909.123956 70909.123956 60: seq: 1b, queue_step oid=5 interval=668 count=489 add=0, queue_step oid=5 interval=678 count=214 add=0, queue_step oid=5 interval=692 count=166 add=0, queue_step oid=5 interval=709 count=141 add=0, queue_step oid=5 interval=729 count=121 add=0, queue_step oid=5 interval=752 count=109 add=0, queue_step oid=5 interval=779 count=101 add=0, queue_step oid=5 interval=810 count=92 add=0
Sent 18 70909.123956 70909.123956 60: seq: 1c, queue_step oid=5 interval=846 count=86 add=0, queue_step oid=5 interval=887 count=76 add=0, queue_step oid=5 interval=934 count=72 add=0, queue_step oid=5 interval=958 count=179 add=1, queue_step oid=5 interval=1182 count=78 add=1, queue_step oid=5 interval=1318 count=87 add=2, queue_step oid=5 interval=1551 count=87 add=4, queue_step oid=5 interval=1969 count=74 add=9, queue_step oid=5 interval=2730 count=54 add=24
Sent 19 70909.133543 70909.133543 64: seq: 1d, queue_step oid=5 interval=4261 count=30 add=69, queue_step oid=5 interval=6736 count=17 add=218, queue_step oid=5 interval=11210 count=9 add=747, queue_step oid=5 interval=19202 count=5 add=2879, queue_step oid=5 interval=39786 count=2 add=12925, queue_step oid=5 interval=80802 count=1 add=0, queue_step oid=5 interval=29686800 count=1 add=0, queue_step oid=5 interval=133918 count=1 add=0
Sent 20 70909.133543 70909.133543 64: seq: 1e, queue_step oid=5 interval=63687 count=2 add=-16081, queue_step oid=5 interval=35897 count=5 add=-3455, queue_step oid=5 interval=21377 count=9 add=-911, queue_step oid=5 interval=13937 count=18 add=-275, queue_step oid=5 interval=9324 count=33 add=-96, queue_step oid=5 interval=6458 count=44 add=-39, queue_step oid=5 interval=4961 count=62 add=-9, queue_step oid=5 interval=4599 count=94 add=3
Sent 21 70909.133543 70909.133543 62: seq: 1f, queue_step oid=5 interval=4971 count=79 add=11, queue_step oid=5 interval=6123 count=71 add=12, queue_step oid=5 interval=6617 count=59 add=10, queue_step oid=5 interval=7455 count=29 add=64, queue_step oid=5 interval=9616 count=18 add=208, queue_step oid=5 interval=13895 count=9 add=766, queue_step oid=5 interval=22541 count=4 add=3648, queue_step oid=5 interval=49932 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 22 70909.133543 70909.133543 63: seq: 10, queue_step oid=5 interval=173932 count=1 add=0, queue_step oid=5 interval=51277 count=2 add=-11360, queue_step oid=5 interval=31924 count=5 add=-1049, queue_step oid=5 interval=26914 count=5 add=2223, queue_step oid=5 interval=47543 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=204535 count=1 add=0, queue_step oid=5 interval=40216 count=3 add=-7239
Sent 23 70909.133543 70909.133543 60: seq: 11, queue_step oid=5 interval=22000 count=8 add=-1318, queue_step oid=5 interval=13193 count=13 add=-382, queue_step oid=5 interval=8725 count=27 add=-115, queue_step oid=5 interval=6013 count=42 add=-34, queue_step oid=5 interval=4823 count=66 add=-4, queue_step oid=5 interval=4716 count=90 add=6, queue_step oid=5 interval=5393 count=99 add=16, queue_step oid=5 interval=6717 count=84 add=2
Sent 24 70909.133543 70909.133543 61: seq: 12, queue_step oid=5 interval=7120 count=32 add=40, queue_step oid=5 interval=8740 count=22 add=138, queue_step oid=5 interval=12491 count=11 add=450, queue_step oid=5 interval=19117 count=5 add=1801, queue_step oid=5 interval=32204 count=2 add=10039, queue_step oid=5 interval=77474 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=53098 count=2 add=25102
Sent 25 70909.133543 70909.133543 57: seq: 13, queue_step oid=5 interval=39969 count=3 add=-5657, queue_step oid=5 interval=24720 count=8 add=-561, queue_step oid=5 interval=21828 count=5 add=1206, queue_step oid=5 interval=28484 count=3 add=8432, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=187356 count=1 add=0, queue_step oid=5 interval=42052 count=3 add=-8423
Sent 26 70909.133543 70909.133543 59: seq: 14, queue_step oid=5 interval=22872 count=6 add=-1669, queue_step oid=5 interval=14003 count=14 add=-400, queue_step oid=5 interval=8810 count=28 add=-117, queue_step oid=5 interval=5943 count=40 add=-35, queue_step oid=5 interval=4767 count=63 add=-4, queue_step oid=5 interval=4682 count=90 add=5, queue_step oid=5 interval=5242 count=75 add=15, queue_step oid=5 interval=6621 count=85 add=3
Sent 27 70909.133543 70909.133543 57: seq: 15, queue_step oid=5 interval=6606 count=58 add=11, queue_step oid=5 interval=7401 count=31 add=72, queue_step oid=5 interval=10064 count=16 add=224, queue_step oid=5 interval=14048 count=9 add=853, queue_step oid=5 interval=24708 count=3 add=3607, queue_step oid=5 interval=41252 count=1 add=0, queue_step oid=5 interval=75919 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 28 70909.133543 70909.133543 64: seq: 16, queue_step oid=5 interval=57367 count=2 add=18600, queue_step oid=5 interval=39618 count=3 add=-5495, queue_step oid=5 interval=24782 count=8 add=-583, queue_step oid=5 interval=22170 count=5 add=1112, queue_step oid=5 interval=29485 count=2 add=6836, queue_step oid=5 interval=46594 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=187229 count=1 add=0
Sent 29 70909.133543 70909.133543 63: seq: 17, queue_step oid=5 interval=41829 count=3 add=-8298, queue_step oid=5 interval=22753 count=6 add=-1620, queue_step oid=5 interval=13897 count=15 add=-384, queue_step oid=5 interval=8690 count=27 add=-117, queue_step oid=5 interval=5887 count=43 add=-32, queue_step oid=5 interval=4737 count=65 add=-3, queue_step oid=5 interval=4676 count=97 add=6, queue_step oid=5 interval=5405 count=98 add=16
Sent 30 70909.133543 70909.133543 59: seq: 18, queue_step oid=5 interval=6704 count=96 add=2, queue_step oid=5 interval=7063 count=34 add=45, queue_step oid=5 interval=8870 count=21 add=155, queue_step oid=5 interval=12487 count=11 add=556, queue_step oid=5 interval=19886 count=4 add=2436, queue_step oid=5 interval=30500 count=2 add=10323, queue_step oid=5 interval=66811 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 31 70909.133944 70909.133944 64: seq: 19, queue_step oid=5 interval=84911 count=2 add=-16463, queue_step oid=5 interval=39308 count=3 add=-5070, queue_step oid=5 interval=25235 count=7 add=-422, queue_step oid=5 interval=22406 count=5 add=1836, queue_step oid=5 interval=32869 count=2 add=10626, queue_step oid=5 interval=74498 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=71245 count=2 add=0
Sent 32 70909.134066 70909.134066 61: seq: 1a, queue_step oid=5 interval=37629 count=3 add=-5990, queue_step oid=5 interval=21043 count=8 add=-1129, queue_step oid=5 interval=12477 count=18 add=-283, queue_step oid=5 interval=7855 count=29 add=-89, queue_step oid=5 interval=5539 count=50 add=-22, queue_step oid=5 interval=4642 count=82 add=1, queue_step oid=5 interval=4845 count=82 add=8, queue_step oid=5 interval=5734 count=85 add=15
Sent 33 70909.134230 70909.134230 60: seq: 1b, queue_step oid=5 interval=6602 count=47 add=33, queue_step oid=5 interval=8507 count=23 add=122, queue_step oid=5 interval=11940 count=12 add=392, queue_step oid=5 interval=18136 count=5 add=1551, queue_step oid=5 interval=26798 count=3 add=7854, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=193519 count=1 add=0, queue_step oid=5 interval=42033 count=3 add=-6890
Sent 34 70909.134382 70909.134382 64: seq: 1c, queue_step oid=5 interval=25576 count=7 add=-797, queue_step oid=5 interval=21345 count=6 add=941, queue_step oid=5 interval=28631 count=3 add=7111, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=205201 count=1 add=0, queue_step oid=5 interval=39305 count=3 add=-6914, queue_step oid=5 interval=21549 count=8 add=-1252, queue_step oid=5 interval=12804 count=15 add=-330
Sent 35 70909.134534 70909.134534 57: seq: 1d, queue_step oid=5 interval=8261 count=29 add=-100, queue_step oid=5 interval=5666 count=47 add=-26, queue_step oid=5 interval=4680 count=69 add=-1, queue_step oid=5 interval=4719 count=94 add=7, queue_step oid=5 interval=5487 count=44 add=28, queue_step oid=5 interval=6881 count=31 add=87, queue_step oid=5 interval=9943 count=17 add=226, queue_step oid=5 interval=14570 count=8 add=830
Sent 36 70909.134679 70909.134679 63: seq: 1e, queue_step oid=5 interval=22432 count=4 add=3982, queue_step oid=5 interval=52468 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=150096 count=1 add=0, queue_step oid=5 interval=49658 count=2 add=-12386, queue_step oid=5 interval=28869 count=6 add=-1482, queue_step oid=5 interval=21226 count=7 add=446, queue_step oid=5 interval=25250 count=3 add=3911
Sent 37 70909.134810 70909.134810 63: seq: 1f, queue_step oid=5 interval=39040 count=2 add=23567, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=113898 count=1 add=0, queue_step oid=5 interval=57346 count=2 add=-19582, queue_step oid=5 interval=27467 count=5 add=-2414, queue_step oid=5 interval=15987 count=13 add=-544, queue_step oid=5 interval=9779 count=22 add=-167, queue_step oid=5 interval=6603 count=32 add=-56
Sent 38 70909.134947 70909.134947 63: seq: 10, queue_step oid=5 interval=5069 count=54 add=-12, queue_step oid=5 interval=4584 count=73 add=5, queue_step oid=5 interval=5115 count=42 add=28, queue_step oid=5 interval=6471 count=26 add=98, queue_step oid=5 interval=9260 count=14 add=379, queue_step oid=5 interval=15895 count=5 add=1547, queue_step oid=5 interval=24335 count=3 add=6616, queue_step oid=5 interval=73071 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 39 70909.147539 70909.147539 63: seq: 11, queue_step oid=5 interval=63037 count=2 add=10918, queue_step oid=5 interval=39422 count=3 add=-5403, queue_step oid=5 interval=24767 count=8 add=-573, queue_step oid=5 interval=22214 count=5 add=1142, queue_step oid=5 interval=29775 count=2 add=7051, queue_step oid=5 interval=47865 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=179598 count=1 add=0
Sent 40 70909.147539 70909.147539 63: seq: 12, queue_step oid=5 interval=43010 count=3 add=-8884, queue_step oid=5 interval=23238 count=6 add=-1807, queue_step oid=5 interval=14463 count=12 add=-491, queue_step oid=5 interval=9510 count=21 add=-163, queue_step oid=5 interval=6506 count=34 add=-47, queue_step oid=5 interval=5118 count=49 add=0, queue_step oid=5 interval=5333 count=42 add=36, queue_step oid=5 interval=7051 count=23 add=120
Sent 41 70909.147539 70909.147539 57: seq: 13, queue_step oid=5 interval=10043 count=11 add=480, queue_step oid=5 interval=15836 count=5 add=2128, queue_step oid=5 interval=32732 count=2 add=23671, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=70064 count=2 add=-10164, queue_step oid=5 interval=35597 count=4 add=-3859, queue_step oid=5 interval=24339 count=6 add=-162
Sent 42 70909.147539 70909.147539 64: seq: 14, queue_step oid=5 interval=26234 count=3 add=2647, queue_step oid=5 interval=36650 count=2 add=16513, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=161676 count=1 add=0, queue_step oid=5 interval=47839 count=2 add=-12269, queue_step oid=5 interval=26870 count=6 add=-1955, queue_step oid=5 interval=16258 count=14 add=-434, queue_step oid=5 interval=10987 count=23 add=-138
Sent 43 70909.147539 70909.147539 60: seq: 15, queue_step oid=5 interval=8311 count=27 add=-12, queue_step oid=5 interval=8372 count=20 add=121, queue_step oid=5 interval=11407 count=10 add=515, queue_step oid=5 interval=17268 count=4 add=2538, queue_step oid=5 interval=28159 count=2 add=11659, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=188111 count=1 add=0, queue_step oid=5 interval=43799 count=3 add=-6769
Sent 44 70909.147539 70909.147539 63: seq: 16, queue_step oid=5 interval=26829 count=9 add=-902, queue_step oid=5 interval=19136 count=15 add=-90, queue_step oid=5 interval=18856 count=10 add=453, queue_step oid=5 interval=24439 count=6 add=1702, queue_step oid=5 interval=37333 count=3 add=7961, queue_step oid=5 interval=78462 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=4298482 count=1 add=0
Sent 45 70909.147539 70909.147539 64: seq: 17, queue_step oid=5 interval=70705 count=2 add=-20109, queue_step oid=5 interval=37592 count=5 add=-4014, queue_step oid=5 interval=21226 count=7 add=-1182, queue_step oid=5 interval=13493 count=17 add=-343, queue_step oid=5 interval=8430 count=24 add=-121, queue_step oid=5 interval=5854 count=46 add=-43, queue_step oid=5 interval=4116 count=59 add=-18, queue_step oid=5 interval=3235 count=90 add=-6
Sent 46 70909.147539 70909.147539 61: seq: 18, queue_step oid=5 interval=2777 count=111 add=-1, queue_step oid=5 interval=2762 count=110 add=3, queue_step oid=5 interval=3165 count=73 add=11, queue_step oid=5 interval=4105 count=50 add=34, queue_step oid=5 interval=6008 count=25 add=114, queue_step oid=5 interval=9357 count=15 add=354, queue_step oid=5 interval=15059 count=18 add=779, queue_step oid=5 interval=26666 count=12 add=-1130
Sent 47 70909.147539 70909.147539 60: seq: 19, queue_step oid=5 interval=13700 count=16 add=-383, queue_step oid=5 interval=8366 count=23 add=-138, queue_step oid=5 interval=5470 count=44 add=-42, queue_step oid=5 interval=3855 count=68 add=-14, queue_step oid=5 interval=3034 count=102 add=-5, queue_step oid=5 interval=2630 count=102 add=-1, queue_step oid=5 interval=2586 count=107 add=3, queue_step oid=5 interval=2987 count=80 add=11
Sent 48 70909.147539 70909.147539 64: seq: 1a, queue_step oid=5 interval=4017 count=53 add=30, queue_step oid=5 interval=5798 count=33 add=70, queue_step oid=5 interval=8300 count=20 add=202, queue_step oid=5 interval=12635 count=14 add=505, queue_step oid=5 interval=20741 count=12 add=933, queue_step oid=5 interval=28890 count=10 add=-856, queue_step oid=5 interval=21670 count=19 add=-322, queue_step oid=5 interval=14421 count=25 add=-235
Sent 49 70909.147539 70909.147539 59: seq: 1b, queue_step oid=5 interval=8956 count=31 add=-108, queue_step oid=5 interval=5936 count=42 add=-47, queue_step oid=5 interval=4241 count=65 add=-17, queue_step oid=5 interval=3283 count=91 add=-7, queue_step oid=5 interval=2738 count=119 add=-2, queue_step oid=5 interval=2563 count=141 add=1, queue_step oid=5 interval=2799 count=141 add=3, queue_step oid=5 interval=3284 count=101 add=7
Sent 50 70909.147539 70909.147539 56: seq: 1c, queue_step oid=5 interval=4121 count=53 add=18, queue_step oid=5 interval=5278 count=33 add=62, queue_step oid=5 interval=7521 count=18 add=198, queue_step oid=5 interval=11310 count=8 add=861, queue_step oid=5 interval=18759 count=3 add=4269, queue_step oid=5 interval=34553 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=179816 count=1 add=0
Sent 51 70909.147890 70909.147890 64: seq: 1d, queue_step oid=5 interval=36314 count=3 add=-4737, queue_step oid=5 interval=22899 count=9 add=-589, queue_step oid=5 interval=19261 count=6 add=627, queue_step oid=5 interval=23601 count=3 add=4468, queue_step oid=5 interval=44595 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=119157 count=1 add=0, queue_step oid=5 interval=42299 count=2 add=-11458
Sent 52 70909.147950 70909.147950 62: seq: 1e, queue_step oid=5 interval=22736 count=7 add=-1694, queue_step oid=5 interval=13009 count=11 add=-454, queue_step oid=5 interval=8426 count=28 add=-125, queue_step oid=5 interval=5324 count=39 add=-46, queue_step oid=5 interval=3756 count=69 add=-14, queue_step oid=5 interval=2909 count=104 add=-4, queue_step oid=5 interval=2604 count=106 add=-1, queue_step oid=5 interval=2560 count=152 add=1
Sent 53 70909.148086 70909.148086 64: seq: 1f, queue_step oid=5 interval=2808 count=273 add=3, queue_step oid=5 interval=3485 count=99 add=9, queue_step oid=5 interval=4551 count=44 add=30, queue_step oid=5 interval=6088 count=30 add=80, queue_step oid=5 interval=8674 count=16 add=277, queue_step oid=5 interval=14094 count=7 add=1087, queue_step oid=5 interval=22366 count=4 add=4355, queue_step oid=5 interval=52451 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 54 70909.148160 70909.148160 62: seq: 10, queue_step oid=5 interval=224310 count=1 add=0, queue_step oid=5 interval=66947 count=2 add=-2927, queue_step oid=5 interval=79165 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=127931 count=1 add=0, queue_step oid=5 interval=67801 count=2 add=-22467, queue_step oid=5 interval=34075 count=5 add=-2855, queue_step oid=5 interval=20456 count=11 add=-858
Sent 55 70909.148301 70909.148301 60: seq: 11, queue_step oid=5 interval=12140 count=16 add=-275, queue_step oid=5 interval=8191 count=32 add=-99, queue_step oid=5 interval=5369 count=42 add=-41, queue_step oid=5 interval=3836 count=75 add=-12, queue_step oid=5 interval=3087 count=101 add=-5, queue_step oid=5 interval=2655 count=132 add=-1, queue_step oid=5 interval=2593 count=118 add=1, queue_step oid=5 interval=2810 count=242 add=3
Sent 56 70909.148368 70909.148368 63: seq: 12, queue_step oid=5 interval=3434 count=130 add=1, queue_step oid=5 interval=3671 count=75 add=7, queue_step oid=5 interval=4343 count=46 add=25, queue_step oid=5 interval=5676 count=30 add=83, queue_step oid=5 interval=8389 count=15 add=288, queue_step oid=5 interval=13477 count=6 add=1326, queue_step oid=5 interval=23472 count=2 add=6751, queue_step oid=5 interval=41219 count=1 add=0, set_next_step_dir oid=5 dir=0
Sent 57 70909.148525 70909.148525 64: seq: 13, queue_step oid=5 interval=137719 count=1 add=0, queue_step oid=5 interval=43204 count=2 add=-9393, queue_step oid=5 interval=26363 count=7 add=-1299, queue_step oid=5 interval=19349 count=8 add=88, queue_step oid=5 interval=21450 count=4 add=2442, queue_step oid=5 interval=34433 count=2 add=28172, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=52455 count=2 add=9347
Sent 58 70909.158391 70909.158391 61: seq: 14, queue_step oid=5 interval=31811 count=3 add=-4733, queue_step oid=5 interval=18172 count=9 add=-915, queue_step oid=5 interval=10587 count=20 add=-225, queue_step oid=5 interval=6658 count=31 add=-80, queue_step oid=5 interval=4475 count=50 add=-27, queue_step oid=5 interval=3326 count=78 add=-9, queue_step oid=5 interval=2753 count=91 add=-3, queue_step oid=5 interval=2562 count=149 add=0
Sent 59 70909.158391 70909.158391 58: seq: 15, queue_step oid=5 interval=2608 count=134 add=2, queue_step oid=5 interval=2960 count=190 add=3, queue_step oid=5 interval=3465 count=171 add=0, queue_step oid=5 interval=3535 count=89 add=4, queue_step oid=5 interval=4012 count=58 add=16, queue_step oid=5 interval=5149 count=37 add=52, queue_step oid=5 interval=7328 count=21 add=150, queue_step oid=5 interval=11122 count=9 add=577
Sent 60 70909.158391 70909.158391 63: seq: 16, queue_step oid=5 interval=16472 count=5 add=2535, queue_step oid=5 interval=31411 count=2 add=13074, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=197702 count=1 add=0, queue_step oid=5 interval=47318 count=3 add=-6940, queue_step oid=5 interval=32340 count=4 add=0, queue_step oid=5 interval=34372 count=2 add=6684, queue_step oid=5 interval=54016 count=1 add=0
Sent 61 70909.158391 70909.158391 60: seq: 17, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=148189 count=1 add=0, queue_step oid=5 interval=52563 count=2 add=-14306, queue_step oid=5 interval=28900 count=6 add=-2344, queue_step oid=5 interval=16286 count=12 add=-607, queue_step oid=5 interval=10006 count=21 add=-180, queue_step oid=5 interval=6626 count=37 add=-67, queue_step oid=5 interval=4422 count=52 add=-24
Sent 62 70909.158391 70909.158391 64: seq: 18, queue_step oid=5 interval=3340 count=91 add=-7, queue_step oid=5 interval=2823 count=106 add=-3, queue_step oid=5 interval=2584 count=145 add=0, queue_step oid=5 interval=2667 count=106 add=2, queue_step oid=5 interval=2962 count=189 add=3, queue_step oid=5 interval=3468 count=242 add=0, queue_step oid=5 interval=3530 count=92 add=5, queue_step oid=5 interval=4105 count=54 add=19, queue_step oid=5 interval=5293 count=34 add=67
Sent 63 70909.158391 70909.158391 61: seq: 19, queue_step oid=5 interval=7948 count=16 add=208, queue_step oid=5 interval=11541 count=8 add=919, queue_step oid=5 interval=20647 count=3 add=4653, queue_step oid=5 interval=43611 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=125403 count=1 add=0, queue_step oid=5 interval=45443 count=2 add=-10944, queue_step oid=5 interval=26630 count=6 add=-1359
Sent 64 70909.158391 70909.158391 57: seq: 1a, queue_step oid=5 interval=18838 count=10 add=165, queue_step oid=5 interval=23299 count=3 add=2233, queue_step oid=5 interval=31967 count=2 add=16812, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=101894 count=1 add=0, queue_step oid=5 interval=45480 count=2 add=-13914, queue_step oid=5 interval=22959 count=6 add=-1751
Sent 65 70909.158391 70909.158391 60: seq: 1b, queue_step oid=5 interval=13071 count=15 add=-384, queue_step oid=5 interval=7958 count=27 add=-116, queue_step oid=5 interval=5145 count=43 add=-40, queue_step oid=5 interval=3621 count=75 add=-12, queue_step oid=5 interval=2857 count=92 add=-4, queue_step oid=5 interval=2561 count=169 add=0, queue_step oid=5 interval=2603 count=136 add=2, queue_step oid=5 interval=2958 count=190 add=3
Sent 66 70909.158391 70909.158391 64: seq: 1c, queue_step oid=5 interval=3467 count=297 add=0, queue_step oid=5 interval=3541 count=87 add=4, queue_step oid=5 interval=3979 count=60 add=17, queue_step oid=5 interval=5153 count=37 add=58, queue_step oid=5 interval=7491 count=20 add=177, queue_step oid=5 interval=11912 count=8 add=678, queue_step oid=5 interval=18195 count=4 add=3182, queue_step oid=5 interval=33533 count=2 add=19843, set_next_step_dir oid=5 dir=0
Sent 67 70909.158391 70909.158391 64: seq: 1d, queue_step oid=5 interval=127367 count=1 add=0, queue_step oid=5 interval=54976 count=2 add=-15063, queue_step oid=5 interval=31256 count=6 add=-1340, queue_step oid=5 interval=26159 count=4 add=1487, queue_step oid=5 interval=33878 count=2 add=11844, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=173847 count=1 add=0, queue_step oid=5 interval=42705 count=3 add=-8359
Sent 68 70909.158391 70909.158391 61: seq: 1e, queue_step oid=5 interval=23704 count=6 add=-1831, queue_step oid=5 interval=14255 count=13 add=-472, queue_step oid=5 interval=9073 count=22 add=-154, queue_step oid=5 interval=6072 count=39 add=-57, queue_step oid=5 interval=4113 count=58 add=-19, queue_step oid=5 interval=3174 count=89 add=-6, queue_step oid=5 interval=2740 count=123 add=-2, queue_step oid=5 interval=2590 count=121 add=0
Sent 69 70909.158391 70909.158391 58: seq: 1f, queue_step oid=5 interval=2642 count=203 add=3, queue_step oid=5 interval=3347 count=178 add=1, queue_step oid=5 interval=3469 count=266 add=0, queue_step oid=5 interval=3549 count=89 add=5, queue_step oid=5 interval=4118 count=54 add=19, queue_step oid=5 interval=5364 count=32 add=65, queue_step oid=5 interval=7659 count=18 add=211, queue_step oid=5 interval=12265 count=7 add=898
Sent 70 70909.158711 70909.158711 63: seq: 10, queue_step oid=5 interval=19592 count=3 add=4471, queue_step oid=5 interval=38297 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=153747 count=1 add=0, queue_step oid=5 interval=39885 count=3 add=-6675, queue_step oid=5 interval=23756 count=8 add=-831, queue_step oid=5 interval=18975 count=7 add=348, queue_step oid=5 interval=22025 count=4 add=3608
Sent 71 70909.158771 70909.158771 60: seq: 11, queue_step oid=5 interval=56319 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=72866 count=3 add=-19631, queue_step oid=5 interval=23774 count=6 add=-1981, queue_step oid=5 interval=13444 count=13 add=-440, queue_step oid=5 interval=8308 count=27 add=-125, queue_step oid=5 interval=5328 count=39 add=-46, queue_step oid=5 interval=3754 count=69 add=-14
Sent 72 70909.158916 70909.158916 59: seq: 12, queue_step oid=5 interval=2905 count=105 add=-4, queue_step oid=5 interval=2600 count=102 add=-1, queue_step oid=5 interval=2558 count=155 add=1, queue_step oid=5 interval=2808 count=245 add=3, queue_step oid=5 interval=3466 count=377 add=0, queue_step oid=5 interval=3499 count=98 add=4, queue_step oid=5 interval=4009 count=58 add=16, queue_step oid=5 interval=5176 count=35 add=51
Sent 73 70909.158992 70909.158992 63: seq: 13, queue_step oid=5 interval=7272 count=20 add=147, queue_step oid=5 interval=10542 count=10 add=586, queue_step oid=5 interval=17354 count=4 add=2773, queue_step oid=5 interval=29874 count=2 add=13642, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=165391 count=1 add=0, queue_step oid=5 interval=44305 count=3 add=-7794, queue_step oid=5 interval=27472 count=5 add=-1023
Sent 74 70909.159128 70909.159128 64: seq: 14, queue_step oid=5 interval=22679 count=6 add=1188, queue_step oid=5 interval=34835 count=2 add=12802, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=147669 count=1 add=0, queue_step oid=5 interval=45396 count=2 add=-11346, queue_step oid=5 interval=25570 count=6 add=-1971, queue_step oid=5 interval=14425 count=14 add=-462, queue_step oid=5 interval=8879 count=22 add=-149
Sent 75 70909.168655 70909.168655 59: seq: 15, queue_step oid=5 interval=5899 count=42 add=-52, queue_step oid=5 interval=3951 count=65 add=-16, queue_step oid=5 interval=3057 count=93 add=-5, queue_step oid=5 interval=2702 count=105 add=-2, queue_step oid=5 interval=2587 count=120 add=0, queue_step oid=5 interval=2671 count=105 add=2, queue_step oid=5 interval=2963 count=190 add=3, queue_step oid=5 interval=3468 count=439 add=0
Sent 76 70909.168655 70909.168655 62: seq: 16, queue_step oid=5 interval=3552 count=85 add=4, queue_step oid=5 interval=4009 count=57 add=16, queue_step oid=5 interval=5049 count=36 add=58, queue_step oid=5 interval=7380 count=19 add=181, queue_step oid=5 interval=11291 count=8 add=779, queue_step oid=5 interval=17795 count=4 add=3946, queue_step oid=5 interval=47496 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=112601 count=1 add=0
Sent 77 70909.168655 70909.168655 57: seq: 17, queue_step oid=5 interval=48080 count=2 add=-12832, queue_step oid=5 interval=27004 count=6 add=-1456, queue_step oid=5 interval=18936 count=9 add=131, queue_step oid=5 interval=20656 count=4 add=2146, queue_step oid=5 interval=30773 count=2 add=13771, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=121251 count=1 add=0
Sent 78 70909.168655 70909.168655 64: seq: 18, queue_step oid=5 interval=40852 count=2 add=-10721, queue_step oid=5 interval=22226 count=7 add=-1615, queue_step oid=5 interval=12665 count=13 add=-396, queue_step oid=5 interval=8017 count=29 add=-113, queue_step oid=5 interval=5155 count=38 add=-44, queue_step oid=5 interval=3722 count=67 add=-14, queue_step oid=5 interval=2904 count=105 add=-4, queue_step oid=5 interval=2561 count=166 add=0
Sent 79 70909.168655 70909.168655 58: seq: 19, queue_step oid=5 interval=2600 count=139 add=2, queue_step oid=5 interval=2962 count=189 add=3, queue_step oid=5 interval=3463 count=286 add=0, queue_step oid=5 interval=3479 count=202 add=0, queue_step oid=5 interval=3571 count=84 add=5, queue_step oid=5 interval=4088 count=56 add=20, queue_step oid=5 interval=5426 count=33 add=65, queue_step oid=5 interval=7820 count=18 add=205
Sent 80 70909.168655 70909.168655 63: seq: 1a, queue_step oid=5 interval=12384 count=7 add=850, queue_step oid=5 interval=18690 count=4 add=3995, queue_step oid=5 interval=46975 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=137999 count=1 add=0, queue_step oid=5 interval=47769 count=2 add=-11362, queue_step oid=5 interval=28500 count=6 add=-1337, queue_step oid=5 interval=21626 count=7 add=537
Sent 81 70909.168655 70909.168655 62: seq: 1b, queue_step oid=5 interval=29350 count=2 add=5292, queue_step oid=5 interval=45419 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=143381 count=1 add=0, queue_step oid=5 interval=44057 count=2 add=-10999, queue_step oid=5 interval=24742 count=6 add=-1881, queue_step oid=5 interval=13991 count=14 add=-432, queue_step oid=5 interval=8521 count=27 add=-125
Sent 82 70909.168655 70909.168655 59: seq: 1c, queue_step oid=5 interval=5444 count=43 add=-44, queue_step oid=5 interval=3751 count=73 add=-13, queue_step oid=5 interval=2940 count=98 add=-4, queue_step oid=5 interval=2633 count=123 add=-1, queue_step oid=5 interval=2573 count=137 add=1, queue_step oid=5 interval=2807 count=243 add=3, queue_step oid=5 interval=3468 count=506 add=0, queue_step oid=5 interval=3545 count=86 add=4
Sent 83 70909.168655 70909.168655 56: seq: 1d, queue_step oid=5 interval=4005 count=58 add=16, queue_step oid=5 interval=5101 count=35 add=57, queue_step oid=5 interval=7365 count=19 add=177, queue_step oid=5 interval=11193 count=9 add=749, queue_step oid=5 interval=20932 count=3 add=3844, queue_step oid=5 interval=40192 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=144196 count=1 add=0
Sent 84 70909.168655 70909.168655 64: seq: 1e, queue_step oid=5 interval=41446 count=3 add=-7630, queue_step oid=5 interval=24604 count=6 add=-1140, queue_step oid=5 interval=18570 count=9 add=257, queue_step oid=5 interval=22234 count=4 add=3079, queue_step oid=5 interval=49632 count=1 add=0, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=99173 count=1 add=0, queue_step oid=5 interval=45641 count=2 add=-14168
Sent 85 70909.168655 70909.168655 61: seq: 1f, queue_step oid=5 interval=22845 count=6 add=-1742, queue_step oid=5 interval=13027 count=15 add=-381, queue_step oid=5 interval=7924 count=28 add=-113, queue_step oid=5 interval=5126 count=41 add=-41, queue_step oid=5 interval=3634 count=76 add=-12, queue_step oid=5 interval=2856 count=92 add=-4, queue_step oid=5 interval=2561 count=167 add=0, queue_step oid=5 interval=2600 count=140 add=2
Sent 86 70909.168655 70909.168655 59: seq: 10, queue_step oid=5 interval=2964 count=188 add=3, queue_step oid=5 interval=3466 count=517 add=0, queue_step oid=5 interval=3513 count=88 add=2, queue_step oid=5 interval=3792 count=69 add=11, queue_step oid=5 interval=4689 count=41 add=40, queue_step oid=5 interval=6529 count=25 add=119, queue_step oid=5 interval=10000 count=11 add=451, queue_step oid=5 interval=16316 count=5 add=1891
Sent 87 70909.168972 70909.168972 64: seq: 11, queue_step oid=5 interval=31841 count=2 add=14137, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=139142 count=1 add=0, queue_step oid=5 interval=46775 count=2 add=-10879, queue_step oid=5 interval=28033 count=6 add=-1297, queue_step oid=5 interval=20861 count=7 add=545, queue_step oid=5 interval=25987 count=3 add=4694, queue_step oid=5 interval=54697 count=1 add=0
Sent 88 70909.169034 70909.169034 60: seq: 12, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=98372 count=1 add=0, queue_step oid=5 interval=53272 count=2 add=-17865, queue_step oid=5 interval=25936 count=6 add=-2213, queue_step oid=5 interval=14503 count=12 add=-522, queue_step oid=5 interval=9037 count=24 add=-151, queue_step oid=5 interval=5893 count=35 add=-59, queue_step oid=5 interval=4089 count=59 add=-19
Sent 89 70909.169185 70909.169185 59: seq: 13, queue_step oid=5 interval=3127 count=90 add=-6, queue_step oid=5 interval=2708 count=109 add=-2, queue_step oid=5 interval=2581 count=124 add=0, queue_step oid=5 interval=2657 count=110 add=2, queue_step oid=5 interval=2960 count=191 add=3, queue_step oid=5 interval=3466 count=532 add=0, queue_step oid=5 interval=3482 count=100 add=2, queue_step oid=5 interval=3775 count=70 add=11
Sent 90 70909.169297 70909.169297 59: seq: 14, queue_step oid=5 interval=4669 count=40 add=40, queue_step oid=5 interval=6460 count=24 add=125, queue_step oid=5 interval=9718 count=11 add=489, queue_step oid=5 interval=15716 count=5 add=2425, queue_step oid=5 interval=36681 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=174915 count=1 add=0, queue_step oid=5 interval=36805 count=3 add=-4999
Sent 91 70909.169375 70909.169375 63: seq: 15, queue_step oid=5 interval=22862 count=9 add=-612, queue_step oid=5 interval=18987 count=7 add=554, queue_step oid=5 interval=25392 count=3 add=5342, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=163961 count=1 add=0, queue_step oid=5 interval=32850 count=3 add=-5266, queue_step oid=5 interval=18199 count=9 add=-922, queue_step oid=5 interval=10591 count=19 add=-226
Sent 92 70909.170439 70909.170439 59: seq: 16, queue_step oid=5 interval=6649 count=36 add=-72, queue_step oid=5 interval=4310 count=56 add=-23, queue_step oid=5 interval=3219 count=79 add=-8, queue_step oid=5 interval=2696 count=109 add=-2, queue_step oid=5 interval=2569 count=124 add=0, queue_step oid=5 interval=2617 count=131 add=2, queue_step oid=5 interval=2961 count=191 add=3, queue_step oid=5 interval=3467 count=591 add=0
Sent 93 70909.170439 70909.170439 62: seq: 17, queue_step oid=5 interval=3535 count=85 add=3, queue_step oid=5 interval=3884 count=64 add=14, queue_step oid=5 interval=4914 count=39 add=50, queue_step oid=5 interval=7141 count=21 add=147, queue_step oid=5 interval=10789 count=10 add=586, queue_step oid=5 interval=18903 count=4 add=2848, queue_step oid=5 interval=39230 count=1 add=0, set_next_step_dir oid=5 dir=0, queue_step oid=5 interval=179160 count=1 add=0
Sent 94 70909.170439 70909.170439 57: seq: 18, queue_step oid=5 interval=39593 count=3 add=-5577, queue_step oid=5 interval=24657 count=8 add=-571, queue_step oid=5 interval=22563 count=5 add=925, queue_step oid=5 interval=32218 count=2 add=9332, set_next_step_dir oid=5 dir=1, queue_step oid=5 interval=168638 count=1 add=0, queue_step oid=5 interval=38307 count=3 add=-6963
Sent 95 70909.170439 70909.170439 61: seq: 19, queue_step oid=5 interval=20915 count=8 add=-1301, queue_step oid=5 interval=12258 count=13 add=-364, queue_step oid=5 interval=8036 count=29 add=-110, queue_step oid=5 interval=5169 count=43 add=-40, queue_step oid=5 interval=3682 count=68 add=-13, queue_step oid=5 interval=2932 count=97 add=-4, queue_step oid=5 interval=2631 count=122 add=-1, queue_step oid=5 interval=2571 count=139 add=1
Sent 96 70909.232889 70909.232889 20: seq: 1a, queue_digital_out oid=11 clock=3139670852 on_ticks=0, queue_step oid=5 interval=2807 count=244 add=3
Sent 97 70909.304165 70909.304165 14: seq: 1b, queue_digital_out oid=7 clock=3134640013 on_ticks=1416
Sent 98 70909.385832 70909.385832 6: seq: 1c, get_clock
Sent 99 70909.599087 70909.599087 6: seq: 1d, emergency_stop
Dumping receive queue 100 messages
Receive: 0 70899.742546 70899.738442 18: seq: 19, tmcuart_response oid=2 read=b'\n\xfa\xef-\x80,\x02\x08 \xa9'
Receive: 1 70899.747620 70899.743551 18: seq: 1a, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 2 70899.840485 70899.776659 14: seq: 11, analog_in_state oid=6 next_clock=2541398994 value=7688
Receive: 3 70899.880476 70899.776659 15: seq: 11, analog_in_state oid=10 next_clock=2543958994 value=14923
Receive: 4 70900.140538 70899.776659 14: seq: 11, analog_in_state oid=6 next_clock=2560598994 value=7688
Receive: 5 70900.180519 70899.776659 15: seq: 11, analog_in_state oid=10 next_clock=2563158994 value=14910
Receive: 6 70900.440536 70900.320601 14: seq: 11, analog_in_state oid=6 next_clock=2579798994 value=7691
Receive: 7 70900.480534 70900.320601 15: seq: 11, analog_in_state oid=10 next_clock=2582358994 value=14894
Receive: 8 70900.525517 70900.525170 11: seq: 12, clock clock=2566491724
Receive: 9 70900.740513 70900.738930 14: seq: 13, analog_in_state oid=6 next_clock=2598998994 value=7686
Receive: 10 70900.743063 70900.738930 18: seq: 13, tmcuart_response oid=2 read=b'\n\xfa\xef-\x80,\x02\x08 \xa9'
Receive: 11 70900.748183 70900.744074 18: seq: 14, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 12 70900.780579 70900.744074 15: seq: 14, analog_in_state oid=10 next_clock=2601558994 value=14877
Receive: 13 70901.040530 70900.832988 14: seq: 1e, analog_in_state oid=6 next_clock=2618198994 value=7689
Receive: 14 70901.080527 70900.832988 15: seq: 1e, analog_in_state oid=10 next_clock=2620758994 value=14873
Receive: 15 70901.340465 70901.292307 14: seq: 17, analog_in_state oid=6 next_clock=2637398994 value=7689
Receive: 16 70901.380502 70901.292307 15: seq: 17, analog_in_state oid=10 next_clock=2639958994 value=14866
Receive: 17 70901.509737 70901.509512 11: seq: 19, clock clock=2629485210
Receive: 18 70901.640475 70901.618471 14: seq: 1b, analog_in_state oid=6 next_clock=2656598994 value=7690
Receive: 19 70901.680476 70901.618471 15: seq: 1b, analog_in_state oid=10 next_clock=2659158994 value=14870
Receive: 20 70901.738807 70901.738586 15: seq: 1d, stats count=374 sum=926782 sumsq=20076435
Receive: 21 70901.742597 70901.738586 18: seq: 1d, tmcuart_response oid=2 read=b'\n\xfa\xef-\x80,\x02\x08 \xa9'
Receive: 22 70901.747133 70901.743103 18: seq: 1e, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 23 70901.940484 70901.804557 14: seq: 14, analog_in_state oid=6 next_clock=2675798994 value=7685
Receive: 24 70901.980488 70901.804557 15: seq: 14, analog_in_state oid=10 next_clock=2678358994 value=14882
Receive: 25 70902.240474 70902.032969 14: seq: 15, analog_in_state oid=6 next_clock=2694998994 value=7684
Receive: 26 70902.280469 70902.032969 15: seq: 15, analog_in_state oid=10 next_clock=2697558994 value=14894
Receive: 27 70902.494497 70902.494255 11: seq: 17, clock clock=2692509519
Receive: 28 70902.540496 70902.529802 14: seq: 1d, analog_in_state oid=6 next_clock=2714198994 value=7679
Receive: 29 70902.580490 70902.529802 15: seq: 1d, analog_in_state oid=10 next_clock=2716758994 value=14905
Receive: 30 70902.743134 70902.739117 18: seq: 1f, tmcuart_response oid=2 read=b'\n\xfa\xef-\x80,\x02\x08 \xa9'
Receive: 31 70902.747624 70902.743575 18: seq: 10, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 32 70902.840493 70902.743575 14: seq: 10, analog_in_state oid=6 next_clock=2733398994 value=7687
Receive: 33 70902.880482 70902.743575 15: seq: 10, analog_in_state oid=10 next_clock=2735958994 value=14920
Receive: 34 70903.140493 70902.932788 14: seq: 11, analog_in_state oid=6 next_clock=2752598994 value=7687
Receive: 35 70903.180472 70902.932788 15: seq: 11, analog_in_state oid=10 next_clock=2755158994 value=14926
Receive: 36 70903.440507 70902.932788 14: seq: 11, analog_in_state oid=6 next_clock=2771798994 value=7686
Receive: 37 70903.478826 70903.478584 11: seq: 12, clock clock=2755506494
Receive: 38 70903.480517 70903.478584 15: seq: 12, analog_in_state oid=10 next_clock=2774358994 value=14914
Receive: 39 70903.740542 70903.740067 14: seq: 1a, analog_in_state oid=6 next_clock=2790998994 value=7689
Receive: 40 70903.744186 70903.740067 18: seq: 1a, tmcuart_response oid=2 read=b'\n\xfa\xef-\x80,\x02\x08 \xa9'
Receive: 41 70903.748588 70903.744619 18: seq: 1b, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 42 70903.780538 70903.744619 15: seq: 1b, analog_in_state oid=10 next_clock=2793558994 value=14894
Receive: 43 70904.040496 70903.832897 14: seq: 1c, analog_in_state oid=6 next_clock=2810198994 value=7687
Receive: 44 70904.080502 70903.832897 15: seq: 1c, analog_in_state oid=10 next_clock=2812758994 value=14877
Receive: 45 70904.340507 70904.132834 14: seq: 1d, analog_in_state oid=6 next_clock=2829398994 value=7685
Receive: 46 70904.380525 70904.132834 15: seq: 1d, analog_in_state oid=10 next_clock=2831958994 value=14865
Receive: 47 70904.463107 70904.462905 11: seq: 1f, clock clock=2818499134
Receive: 48 70904.640484 70904.462905 14: seq: 1f, analog_in_state oid=6 next_clock=2848598994 value=7687
Receive: 49 70904.680498 70904.462905 15: seq: 1f, analog_in_state oid=10 next_clock=2851158994 value=14861
Receive: 50 70904.745121 70904.741123 18: seq: 10, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc0,\x02\x08 \xa2'
Receive: 51 70904.749559 70904.745553 18: seq: 11, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 52 70904.940502 70904.745553 14: seq: 11, analog_in_state oid=6 next_clock=2867798994 value=7681
Receive: 53 70904.980543 70904.745553 15: seq: 11, analog_in_state oid=10 next_clock=2870358994 value=14861
Receive: 54 70905.240506 70904.745553 14: seq: 11, analog_in_state oid=6 next_clock=2886998994 value=7681
Receive: 55 70905.280505 70904.745553 15: seq: 11, analog_in_state oid=10 next_clock=2889558994 value=14881
Receive: 56 70905.447419 70905.447232 11: seq: 13, clock clock=2881494573
Receive: 57 70905.540507 70905.447232 14: seq: 13, analog_in_state oid=6 next_clock=2906198994 value=7680
Receive: 58 70905.569411 70905.447232 10: seq: 13, buttons_state oid=9 ack_count=7 state=b'\x01'
Receive: 59 70905.580493 70905.569533 15: seq: 14, analog_in_state oid=10 next_clock=2908758994 value=14891
Receive: 60 70905.746055 70905.742054 18: seq: 16, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc0,\x02\x08 \xa2'
Receive: 61 70905.750456 70905.746489 18: seq: 17, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 62 70905.840517 70905.746489 14: seq: 17, analog_in_state oid=6 next_clock=2925398994 value=7681
Receive: 63 70905.880493 70905.746489 15: seq: 17, analog_in_state oid=10 next_clock=2927958994 value=14908
Receive: 64 70906.140526 70905.932817 14: seq: 18, analog_in_state oid=6 next_clock=2944598994 value=7676
Receive: 65 70906.180521 70905.932817 15: seq: 18, analog_in_state oid=10 next_clock=2947158994 value=14926
Receive: 66 70906.432497 70906.432145 11: seq: 19, clock clock=2944529778
Receive: 67 70906.440576 70906.432145 14: seq: 19, analog_in_state oid=6 next_clock=2963798994 value=7682
Receive: 68 70906.480630 70906.432145 15: seq: 19, analog_in_state oid=10 next_clock=2966358994 value=14924
Receive: 69 70906.740617 70906.432145 14: seq: 19, analog_in_state oid=6 next_clock=2982998994 value=7678
Receive: 70 70906.740636 70906.432145 15: seq: 19, stats count=309 sum=580417 sumsq=10596168
Receive: 71 70906.748064 70906.743959 18: seq: 1a, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc0,\x02\x08 \xa2'
Receive: 72 70906.753124 70906.749058 18: seq: 1b, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 73 70906.780575 70906.749058 15: seq: 1b, analog_in_state oid=10 next_clock=2985558994 value=14915
Receive: 74 70907.040599 70906.749058 14: seq: 1b, analog_in_state oid=6 next_clock=3002198994 value=7676
Receive: 75 70907.080564 70906.749058 15: seq: 1b, analog_in_state oid=10 next_clock=3004758994 value=14903
Receive: 76 70907.340609 70907.133101 14: seq: 1c, analog_in_state oid=6 next_clock=3021398994 value=7677
Receive: 77 70907.380673 70907.133101 15: seq: 1c, analog_in_state oid=10 next_clock=3023958994 value=14884
Receive: 78 70907.417233 70907.416913 11: seq: 1d, clock clock=3007557251
Receive: 79 70907.640647 70907.416913 14: seq: 1d, analog_in_state oid=6 next_clock=3040598994 value=7678
Receive: 80 70907.680615 70907.416913 15: seq: 1d, analog_in_state oid=10 next_clock=3043158994 value=14870
Receive: 81 70907.747691 70907.743625 18: seq: 1f, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc0,\x02\x08 \xa2'
Receive: 82 70907.752535 70907.748482 18: seq: 10, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 83 70907.940540 70907.748482 14: seq: 10, analog_in_state oid=6 next_clock=3059798994 value=7678
Receive: 84 70907.980582 70907.748482 15: seq: 10, analog_in_state oid=10 next_clock=3062358994 value=14862
Receive: 85 70908.240547 70908.033033 14: seq: 11, analog_in_state oid=6 next_clock=3078998994 value=7681
Receive: 86 70908.280563 70908.033033 15: seq: 11, analog_in_state oid=10 next_clock=3081558994 value=14868
Receive: 87 70908.401109 70908.400955 11: seq: 13, clock clock=3070530509
Receive: 88 70908.540549 70908.400955 14: seq: 13, analog_in_state oid=6 next_clock=3098198994 value=7681
Receive: 89 70908.580538 70908.400955 15: seq: 13, analog_in_state oid=10 next_clock=3100758994 value=14880
Receive: 90 70908.747917 70908.743927 18: seq: 15, tmcuart_response oid=2 read=b'\n\xfa\xef-\xc0,\x02\x08 \xa2'
Receive: 91 70908.752459 70908.748492 18: seq: 16, tmcuart_response oid=2 read=b'\n\xfa/ \x80\x00\x02\x08\xa0\x89'
Receive: 92 70908.840548 70908.748492 14: seq: 16, analog_in_state oid=6 next_clock=3117398994 value=7680
Receive: 93 70908.880523 70908.748492 15: seq: 16, analog_in_state oid=10 next_clock=3119958994 value=14896
Receive: 94 70909.140537 70909.134947 14: seq: 11, analog_in_state oid=6 next_clock=3136598994 value=7677
Receive: 95 70909.180554 70909.170439 15: seq: 1a, analog_in_state oid=10 next_clock=3139158994 value=14913
Receive: 96 70909.385986 70909.385832 11: seq: 1d, clock clock=3133562064
Receive: 97 70909.440562 70909.385832 14: seq: 1d, analog_in_state oid=6 next_clock=3155798994 value=7680
Receive: 98 70909.480580 70909.385832 15: seq: 1d, analog_in_state oid=10 next_clock=3158358994 value=14928
Receive: 99 70909.599455 70909.599087 12: seq: 1e, shutdown clock=3147210870 static_string_id=Command request
MCU 'beacon' shutdown: Emergency stop
clocksync state: mcu_freq=32000000 last_clock=2269232202587 clock_est=(70880.236 2268317490002 31999569.015) min_half_rtt=0.000173 min_rtt_time=70857.563 time_avg=70880.236(845.059) clock_avg=2268317490002.961(27041523163.402) pred_variance=1565474.273 clock_adj=(0.011 31999640.664)
Dumping serial stats: bytes_write=452298 bytes_read=24629738 bytes_retransmit=9 bytes_invalid=0 send_seq=72762 receive_seq=72762 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0
Dumping send queue 100 messages
Sent 0 70812.236136 70812.236136 6: seq: 16, get_clock
Sent 1 70813.222060 70813.222060 6: seq: 17, get_clock
Sent 2 70814.206630 70814.206630 6: seq: 18, get_clock
Sent 3 70815.191481 70815.191481 6: seq: 19, get_clock
Sent 4 70816.175928 70816.175928 6: seq: 1a, get_clock
Sent 5 70817.160092 70817.160092 6: seq: 1b, get_clock
Sent 6 70818.144190 70818.144190 6: seq: 1c, get_clock
Sent 7 70819.128614 70819.128614 6: seq: 1d, get_clock
Sent 8 70820.112869 70820.112869 6: seq: 1e, get_clock
Sent 9 70821.097583 70821.097583 6: seq: 1f, get_clock
Sent 10 70822.081606 70822.081606 6: seq: 10, get_clock
Sent 11 70823.065822 70823.065822 6: seq: 11, get_clock
Sent 12 70824.049823 70824.049823 6: seq: 12, get_clock
Sent 13 70825.033850 70825.033850 6: seq: 13, get_clock
Sent 14 70826.018326 70826.018326 6: seq: 14, get_clock
Sent 15 70827.007003 70827.007003 6: seq: 15, get_clock
Sent 16 70828.011971 70828.011971 6: seq: 16, get_clock
Sent 17 70828.996983 70828.996983 6: seq: 17, get_clock
Sent 18 70829.981768 70829.981768 6: seq: 18, get_clock
Sent 19 70830.980933 70830.980933 6: seq: 19, get_clock
Sent 20 70831.964953 70831.964953 6: seq: 1a, get_clock
Sent 21 70832.949459 70832.949459 6: seq: 1b, get_clock
Sent 22 70833.934098 70833.934098 6: seq: 1c, get_clock
Sent 23 70834.918835 70834.918835 6: seq: 1d, get_clock
Sent 24 70835.903889 70835.903889 6: seq: 1e, get_clock
Sent 25 70836.888048 70836.888048 6: seq: 1f, get_clock
Sent 26 70837.872285 70837.872285 6: seq: 10, get_clock
Sent 27 70838.856390 70838.856390 6: seq: 11, get_clock
Sent 28 70839.840865 70839.840865 6: seq: 12, get_clock
Sent 29 70840.825130 70840.825130 6: seq: 13, get_clock
Sent 30 70841.810056 70841.810056 6: seq: 14, get_clock
Sent 31 70842.794534 70842.794534 6: seq: 15, get_clock
Sent 32 70843.778830 70843.778830 6: seq: 16, get_clock
Sent 33 70844.763337 70844.763337 6: seq: 17, get_clock
Sent 34 70845.747969 70845.747969 6: seq: 18, get_clock
Sent 35 70846.732986 70846.732986 6: seq: 19, get_clock
Sent 36 70847.717630 70847.717630 6: seq: 1a, get_clock
Sent 37 70848.702111 70848.702111 6: seq: 1b, get_clock
Sent 38 70849.686796 70849.686796 6: seq: 1c, get_clock
Sent 39 70850.671073 70850.671073 6: seq: 1d, get_clock
Sent 40 70851.656077 70851.656077 6: seq: 1e, get_clock
Sent 41 70852.640350 70852.640350 6: seq: 1f, get_clock
Sent 42 70853.625094 70853.625094 6: seq: 10, get_clock
Sent 43 70854.609538 70854.609538 6: seq: 11, get_clock
Sent 44 70855.593912 70855.593912 6: seq: 12, get_clock
Sent 45 70856.578607 70856.578607 6: seq: 13, get_clock
Sent 46 70857.563058 70857.563058 6: seq: 14, get_clock
Sent 47 70858.547195 70858.547195 6: seq: 15, get_clock
Sent 48 70859.532096 70859.532096 6: seq: 16, get_clock
Sent 49 70860.516389 70860.516389 6: seq: 17, get_clock
Sent 50 70861.500513 70861.500513 6: seq: 18, get_clock
Sent 51 70862.484438 70862.484438 6: seq: 19, get_clock
Sent 52 70863.491715 70863.491715 6: seq: 1a, get_clock
Sent 53 70864.476525 70864.476525 6: seq: 1b, get_clock
Sent 54 70865.461351 70865.461351 6: seq: 1c, get_clock
Sent 55 70866.445503 70866.445503 6: seq: 1d, get_clock
Sent 56 70867.429658 70867.429658 6: seq: 1e, get_clock
Sent 57 70868.414121 70868.414121 6: seq: 1f, get_clock
Sent 58 70869.398292 70869.398292 6: seq: 10, get_clock
Sent 59 70870.382682 70870.382682 6: seq: 11, get_clock
Sent 60 70871.367095 70871.367095 6: seq: 12, get_clock
Sent 61 70872.351231 70872.351231 6: seq: 13, get_clock
Sent 62 70873.335412 70873.335412 6: seq: 14, get_clock
Sent 63 70874.319662 70874.319662 6: seq: 15, get_clock
Sent 64 70875.303881 70875.303881 6: seq: 16, get_clock
Sent 65 70876.288387 70876.288387 6: seq: 17, get_clock
Sent 66 70877.272789 70877.272789 6: seq: 18, get_clock
Sent 67 70878.256904 70878.256904 6: seq: 19, get_clock
Sent 68 70879.241864 70879.241864 6: seq: 1a, get_clock
Sent 69 70880.226062 70880.226062 6: seq: 1b, get_clock
Sent 70 70881.210465 70881.210465 6: seq: 1c, get_clock
Sent 71 70882.194658 70882.194658 6: seq: 1d, get_clock
Sent 72 70883.179010 70883.179010 6: seq: 1e, get_clock
Sent 73 70884.163218 70884.163218 6: seq: 1f, get_clock
Sent 74 70885.148196 70885.148196 6: seq: 10, get_clock
Sent 75 70886.133134 70886.133134 6: seq: 11, get_clock
Sent 76 70887.117351 70887.117351 6: seq: 12, get_clock
Sent 77 70888.102105 70888.102105 6: seq: 13, get_clock
Sent 78 70889.086177 70889.086177 6: seq: 14, get_clock
Sent 79 70890.087156 70890.087156 6: seq: 15, get_clock
Sent 80 70891.071917 70891.071917 6: seq: 16, get_clock
Sent 81 70892.056787 70892.056787 6: seq: 17, get_clock
Sent 82 70893.040992 70893.040992 6: seq: 18, get_clock
Sent 83 70894.025186 70894.025186 6: seq: 19, get_clock
Sent 84 70895.009689 70895.009689 6: seq: 1a, get_clock
Sent 85 70895.993905 70895.993905 6: seq: 1b, get_clock
Sent 86 70896.978176 70896.978176 6: seq: 1c, get_clock
Sent 87 70897.986171 70897.986171 6: seq: 1d, get_clock
Sent 88 70898.970940 70898.970940 6: seq: 1e, get_clock
Sent 89 70899.960167 70899.960167 6: seq: 1f, get_clock
Sent 90 70900.944820 70900.944820 6: seq: 10, get_clock
Sent 91 70901.929462 70901.929462 6: seq: 11, get_clock
Sent 92 70902.913639 70902.913639 6: seq: 12, get_clock
Sent 93 70903.898051 70903.898051 6: seq: 13, get_clock
Sent 94 70904.882966 70904.882966 6: seq: 14, get_clock
Sent 95 70905.867166 70905.867166 6: seq: 15, get_clock
Sent 96 70906.852222 70906.852222 6: seq: 16, get_clock
Sent 97 70907.836261 70907.836261 6: seq: 17, get_clock
Sent 98 70908.820863 70908.820863 6: seq: 18, get_clock
Sent 99 70909.606410 70909.606410 6: seq: 19, emergency_stop
Dumping receive queue 100 messages
Receive: 0 70904.902108 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1364028577 delta_clock=0 data=b'\x82\x93\x17\x83'
Receive: 1 70904.922703 70904.882966 16: seq: 15, beacon_status mcu_temp=46176 supply_voltage=49248 coil_temp=47889 status=1
Receive: 2 70905.002140 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1367229334 delta_clock=0 data=b"\x82\x91O'"
Receive: 3 70905.022913 70904.882966 16: seq: 15, beacon_status mcu_temp=46176 supply_voltage=49248 coil_temp=47894 status=1
Receive: 4 70905.102166 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1370430091 delta_clock=0 data=b'\x82\x90.\x9c'
Receive: 5 70905.123090 70904.882966 16: seq: 15, beacon_status mcu_temp=46176 supply_voltage=49248 coil_temp=47900 status=1
Receive: 6 70905.202188 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1373630861 delta_clock=0 data=b'\x82\x8fo,'
Receive: 7 70905.223322 70904.882966 16: seq: 15, beacon_status mcu_temp=46176 supply_voltage=49248 coil_temp=47903 status=1
Receive: 8 70905.302207 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1376831626 delta_clock=0 data=b'\x82\x8e\xee\xab'
Receive: 9 70905.323454 70904.882966 16: seq: 15, beacon_status mcu_temp=46172 supply_voltage=49248 coil_temp=47904 status=1
Receive: 10 70905.402284 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1380032371 delta_clock=0 data=b'\x82\x8e\x92\xd5'
Receive: 11 70905.423767 70904.882966 16: seq: 15, beacon_status mcu_temp=46172 supply_voltage=49248 coil_temp=47904 status=1
Receive: 12 70905.502285 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1383233129 delta_clock=0 data=b'\x82\x8eU\xea'
Receive: 13 70905.523821 70904.882966 16: seq: 15, beacon_status mcu_temp=46172 supply_voltage=49248 coil_temp=47906 status=1
Receive: 14 70905.602291 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1386433881 delta_clock=0 data=b'\x82\x8e$\xbe'
Receive: 15 70905.624027 70904.882966 16: seq: 15, beacon_status mcu_temp=46172 supply_voltage=49248 coil_temp=47906 status=1
Receive: 16 70905.702318 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1389634636 delta_clock=0 data=b'\x82\x8d\xff\xf8'
Receive: 17 70905.724258 70904.882966 16: seq: 15, beacon_status mcu_temp=46172 supply_voltage=49248 coil_temp=47906 status=1
Receive: 18 70905.802332 70904.882966 18: seq: 15, beacon_data samples=1 start_clock=1392835390 delta_clock=0 data=b'\x82\x8d\xe5\xcc'
Receive: 19 70905.824435 70904.882966 16: seq: 15, beacon_status mcu_temp=46168 supply_voltage=49249 coil_temp=47906 status=1
Receive: 20 70905.867535 70905.867166 11: seq: 16, clock clock=1394953529
Receive: 21 70905.902345 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1396036142 delta_clock=0 data=b'\x82\x8d\xd2\xca'
Receive: 22 70905.924634 70905.867166 16: seq: 16, beacon_status mcu_temp=46168 supply_voltage=49249 coil_temp=47905 status=1
Receive: 23 70906.002428 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1399236907 delta_clock=0 data=b'\x82\x8d\xd5h'
Receive: 24 70906.024794 70905.867166 16: seq: 16, beacon_status mcu_temp=46168 supply_voltage=49249 coil_temp=47901 status=1
Receive: 25 70906.102399 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1402437664 delta_clock=0 data=b'\x82\x8d\xd5h'
Receive: 26 70906.125033 70905.867166 16: seq: 16, beacon_status mcu_temp=46168 supply_voltage=49249 coil_temp=47899 status=1
Receive: 27 70906.202450 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1405638422 delta_clock=0 data=b'\x82\x8d\xd5h'
Receive: 28 70906.225214 70905.867166 16: seq: 16, beacon_status mcu_temp=46168 supply_voltage=49249 coil_temp=47899 status=1
Receive: 29 70906.302464 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1408839185 delta_clock=0 data=b'\x82\x8d\xd5h'
Receive: 30 70906.325378 70905.867166 16: seq: 16, beacon_status mcu_temp=46164 supply_voltage=49249 coil_temp=47899 status=1
Receive: 31 70906.402599 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1412039940 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 32 70906.425634 70905.867166 16: seq: 16, beacon_status mcu_temp=46164 supply_voltage=49249 coil_temp=47901 status=1
Receive: 33 70906.502586 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1415240700 delta_clock=0 data=b'\x82\x8d\xd2\xca'
Receive: 34 70906.525874 70905.867166 16: seq: 16, beacon_status mcu_temp=46164 supply_voltage=49249 coil_temp=47907 status=1
Receive: 35 70906.602585 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1418441450 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 36 70906.626117 70905.867166 16: seq: 16, beacon_status mcu_temp=46164 supply_voltage=49249 coil_temp=47910 status=1
Receive: 37 70906.702624 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1421642198 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 38 70906.726199 70905.867166 16: seq: 16, beacon_status mcu_temp=46160 supply_voltage=49249 coil_temp=47912 status=1
Receive: 39 70906.802654 70905.867166 18: seq: 16, beacon_data samples=1 start_clock=1424842958 delta_clock=0 data=b'\x82\x8d\xd2\xca'
Receive: 40 70906.826412 70905.867166 16: seq: 16, beacon_status mcu_temp=46160 supply_voltage=49250 coil_temp=47912 status=1
Receive: 41 70906.852735 70906.852222 11: seq: 17, clock clock=1426477250
Receive: 42 70906.902659 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1428043726 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 43 70906.926601 70906.852222 16: seq: 17, beacon_status mcu_temp=46160 supply_voltage=49250 coil_temp=47916 status=1
Receive: 44 70907.002795 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1431244477 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 45 70907.026819 70906.852222 16: seq: 17, beacon_status mcu_temp=46160 supply_voltage=49250 coil_temp=47918 status=1
Receive: 46 70907.102706 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1434445243 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 47 70907.126970 70906.852222 16: seq: 17, beacon_status mcu_temp=46160 supply_voltage=49250 coil_temp=47921 status=1
Receive: 48 70907.202737 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1437646011 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 49 70907.227213 70906.852222 16: seq: 17, beacon_status mcu_temp=46157 supply_voltage=49251 coil_temp=47921 status=1
Receive: 50 70907.302788 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1440846766 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 51 70907.327341 70906.852222 16: seq: 17, beacon_status mcu_temp=46157 supply_voltage=49251 coil_temp=47921 status=1
Receive: 52 70907.402825 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1444047524 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 53 70907.427551 70906.852222 16: seq: 17, beacon_status mcu_temp=46157 supply_voltage=49251 coil_temp=47918 status=1
Receive: 54 70907.502878 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1447248271 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 55 70907.527773 70906.852222 16: seq: 17, beacon_status mcu_temp=46157 supply_voltage=49251 coil_temp=47916 status=1
Receive: 56 70907.602908 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1450449027 delta_clock=0 data=b'\x82\x8d\xd2\xca'
Receive: 57 70907.628012 70906.852222 16: seq: 17, beacon_status mcu_temp=46157 supply_voltage=49251 coil_temp=47913 status=1
Receive: 58 70907.702880 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1453649785 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 59 70907.728202 70906.852222 16: seq: 17, beacon_status mcu_temp=46154 supply_voltage=49251 coil_temp=47913 status=1
Receive: 60 70907.803037 70906.852222 18: seq: 17, beacon_data samples=1 start_clock=1456850543 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 61 70907.828285 70906.852222 16: seq: 17, beacon_status mcu_temp=46154 supply_voltage=49251 coil_temp=47911 status=1
Receive: 62 70907.836685 70907.836261 11: seq: 18, clock clock=1457964192
Receive: 63 70907.902890 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1460051301 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 64 70907.928431 70907.836261 16: seq: 18, beacon_status mcu_temp=46154 supply_voltage=49251 coil_temp=47908 status=1
Receive: 65 70908.002907 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1463252062 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 66 70908.028658 70907.836261 16: seq: 18, beacon_status mcu_temp=46154 supply_voltage=49251 coil_temp=47906 status=1
Receive: 67 70908.102909 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1466452826 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 68 70908.128818 70907.836261 16: seq: 18, beacon_status mcu_temp=46153 supply_voltage=49251 coil_temp=47904 status=1
Receive: 69 70908.202997 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1469653581 delta_clock=0 data=b'\x82\x8d\xd3T'
Receive: 70 70908.229071 70907.836261 16: seq: 18, beacon_status mcu_temp=46153 supply_voltage=49251 coil_temp=47904 status=1
Receive: 71 70908.302973 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1472854342 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 72 70908.329222 70907.836261 16: seq: 18, beacon_status mcu_temp=46153 supply_voltage=49251 coil_temp=47900 status=1
Receive: 73 70908.402994 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1476055101 delta_clock=0 data=b'\x82\x8d\xd3T'
Receive: 74 70908.429388 70907.836261 16: seq: 18, beacon_status mcu_temp=46153 supply_voltage=49251 coil_temp=47898 status=1
Receive: 75 70908.503046 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1479255868 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 76 70908.529581 70907.836261 16: seq: 18, beacon_status mcu_temp=46153 supply_voltage=49251 coil_temp=47895 status=1
Receive: 77 70908.603040 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1482456631 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 78 70908.629797 70907.836261 16: seq: 18, beacon_status mcu_temp=46152 supply_voltage=49251 coil_temp=47895 status=1
Receive: 79 70908.703056 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1485657387 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 80 70908.730008 70907.836261 16: seq: 18, beacon_status mcu_temp=46152 supply_voltage=49251 coil_temp=47894 status=1
Receive: 81 70908.803109 70907.836261 18: seq: 18, beacon_data samples=1 start_clock=1488858150 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 82 70908.821267 70908.820863 11: seq: 19, clock clock=1489470299
Receive: 83 70908.830166 70908.820863 16: seq: 19, beacon_status mcu_temp=46152 supply_voltage=49251 coil_temp=47891 status=1
Receive: 84 70908.903105 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1492058918 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 85 70908.930378 70908.820863 16: seq: 19, beacon_status mcu_temp=46152 supply_voltage=49251 coil_temp=47888 status=1
Receive: 86 70909.003185 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1495259678 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 87 70909.030555 70908.820863 16: seq: 19, beacon_status mcu_temp=46152 supply_voltage=49251 coil_temp=47886 status=1
Receive: 88 70909.103257 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1498460448 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 89 70909.130767 70908.820863 16: seq: 19, beacon_status mcu_temp=46151 supply_voltage=49251 coil_temp=47886 status=1
Receive: 90 70909.203197 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1501661205 delta_clock=0 data=b'\x82\x8d\xd0-'
Receive: 91 70909.230980 70908.820863 16: seq: 19, beacon_status mcu_temp=46151 supply_voltage=49251 coil_temp=47884 status=1
Receive: 92 70909.303231 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1504861959 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 93 70909.331142 70908.820863 16: seq: 19, beacon_status mcu_temp=46151 supply_voltage=49251 coil_temp=47881 status=1
Receive: 94 70909.403262 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1508062719 delta_clock=0 data=b'\x82\x8d\xd2\xca'
Receive: 95 70909.431381 70908.820863 16: seq: 19, beacon_status mcu_temp=46151 supply_voltage=49251 coil_temp=47879 status=1
Receive: 96 70909.503277 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1511263481 delta_clock=0 data=b'\x82\x8d\xd0\xb6'
Receive: 97 70909.531532 70908.820863 16: seq: 19, beacon_status mcu_temp=46151 supply_voltage=49251 coil_temp=47878 status=1
Receive: 98 70909.603282 70908.820863 18: seq: 19, beacon_data samples=1 start_clock=1514464238 delta_clock=0 data=b'\x82\x8d\xe5\xcc'
Receive: 99 70909.606847 70909.606410 12: seq: 1a, shutdown clock=1514607535 static_string_id=Emergency stop
Reactor garbage collection: (70909.172269494, 70862.852368966, 70785.60088129)
MCU 'mcu' shutdown: Stepper too far in past
This generally occurs when the micro-controller has been
requested to step at a rate higher than it is capable of
obtaining.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown

Dumping stepper 'stepper_x' (mcu) 65 queue_step:
queue_step 0: t=12764704706959 p=-83029 i=565448769 c=1 a=0
queue_step 1: t=12764704790564 p=-83028 i=83605 c=3 a=-18938
queue_step 2: t=12764704942406 p=-83025 i=41446 c=8 a=-2660
queue_step 3: t=12764705182297 p=-83017 i=24249 c=17 a=-602
queue_step 4: t=12764705503985 p=-83000 i=15576 c=34 a=-167
queue_step 5: t=12764705934818 p=-82966 i=10512 c=66 a=-52
queue_step 6: t=12764706514002 p=-82900 i=7444 c=93 a=-21
queue_step 7: t=12764707114701 p=-82807 i=5689 c=125 a=-10
queue_step 8: t=12764707747221 p=-82682 i=4584 c=131 a=-6
queue_step 9: t=12764708295964 p=-82551 i=3913 c=142 a=-4
queue_step 10: t=12764708811097 p=-82409 i=3444 c=139 a=-3
queue_step 11: t=12764709260694 p=-82270 i=3098 c=192 a=-2
queue_step 12: t=12764709818530 p=-82078 i=2790 c=122 a=-2
queue_step 13: t=12764710143945 p=-81956 i=2587 c=165 a=-1
queue_step 14: t=12764710557094 p=-81791 i=2411 c=165 a=-1
queue_step 15: t=12764710941254 p=-81626 i=2286 c=177 a=-1
queue_step 16: t=12764711330174 p=-81449 i=2160 c=146 a=-1
queue_step 17: t=12764711634859 p=-81303 i=2070 c=132 a=-1
queue_step 18: t=12764711899381 p=-81171 i=1998 c=124 a=-1
queue_step 19: t=12764712139445 p=-81047 i=1936 c=115 a=-1
queue_step 20: t=12764712355477 p=-80932 i=1883 c=109 a=-1
queue_step 21: t=12764712554793 p=-80823 i=1838 c=107 a=-1
queue_step 22: t=12764712745746 p=-80716 i=1796 c=103 a=-1
queue_step 23: t=12764712925443 p=-80613 i=1758 c=100 a=-1
queue_step 24: t=12764713096258 p=-80513 i=1723 c=96 a=-1
queue_step 25: t=12764713257075 p=-80417 i=1692 c=95 a=-1
queue_step 26: t=12764713413321 p=-80322 i=1663 c=93 a=-1
queue_step 27: t=12764713563639 p=-80229 i=1600 c=85 a=0
queue_step 28: t=12764713699599 p=-80144 i=1560 c=145 a=0
queue_step 29: t=12764713925761 p=-79999 i=1522 c=154 a=0
queue_step 30: t=12764714160112 p=-79845 i=1485 c=159 a=0
queue_step 31: t=12764714396192 p=-79686 i=1450 c=159 a=0
queue_step 32: t=12764714626709 p=-79527 i=1417 c=165 a=0
queue_step 33: t=12764714860482 p=-79362 i=1385 c=169 a=0
queue_step 34: t=12764715094517 p=-79193 i=1355 c=167 a=0
queue_step 35: t=12764715320773 p=-79026 i=1326 c=180 a=0
queue_step 36: t=12764715559425 p=-78846 i=1298 c=176 a=0
queue_step 37: t=12764715787847 p=-78670 i=1272 c=177 a=0
queue_step 38: t=12764716012966 p=-78493 i=1247 c=184 a=0
queue_step 39: t=12764716242390 p=-78309 i=1223 c=182 a=0
queue_step 40: t=12764716464953 p=-78127 i=1200 c=190 a=0
queue_step 41: t=12764716692931 p=-77937 i=1178 c=187 a=0
queue_step 42: t=12764716913196 p=-77750 i=1157 c=193 a=0
queue_step 43: t=12764717136476 p=-77557 i=1136 c=208 a=0
queue_step 44: t=12764717372744 p=-77349 i=1116 c=196 a=0
queue_step 45: t=12764717591461 p=-77153 i=1097 c=207 a=0
queue_step 46: t=12764717818521 p=-76946 i=1078 c=218 a=0
queue_step 47: t=12764718053507 p=-76728 i=1060 c=206 a=0
queue_step 48: t=12764718271850 p=-76522 i=1043 c=215 a=0
queue_step 49: t=12764718496078 p=-76307 i=1026 c=227 a=0
queue_step 50: t=12764718728964 p=-76080 i=1010 c=210 a=0
queue_step 51: t=12764718941049 p=-75870 i=995 c=218 a=0
queue_step 52: t=12764719157944 p=-75652 i=980 c=230 a=0
queue_step 53: t=12764719383329 p=-75422 i=965 c=244 a=0
queue_step 54: t=12764719618783 p=-75178 i=959 c=1698 a=0
queue_step 55: t=12764721247166 p=-73480 i=960 c=666 a=0
queue_step 56: t=12764721886525 p=-72814 i=959 c=1715 a=0
queue_step 57: t=12764723531211 p=-71099 i=960 c=666 a=0
queue_step 58: t=12764724170570 p=-70433 i=959 c=1716 a=0
queue_step 59: t=12764725816215 p=-68717 i=960 c=666 a=0
queue_step 60: t=12764726455574 p=-68051 i=959 c=1716 a=0
queue_step 61: t=12764728101219 p=-66335 i=960 c=666 a=0
queue_step 62: t=12764728740578 p=-65669 i=959 c=1715 a=0
queue_step 63: t=12764730385264 p=-63954 i=960 c=666 a=0
queue_step 64: t=12764731024623 p=-63288 i=959 c=1716 a=0
Dumping stepper 'stepper_x1' (mcu) 73 queue_step:
queue_step 0: t=12764704696740 p=83013 i=565428492 c=-1 a=0
queue_step 1: t=12764704772922 p=83012 i=76182 c=-3 a=-16723
queue_step 2: t=12764704911797 p=83009 i=36680 c=-9 a=-2000
queue_step 3: t=12764705153720 p=83000 i=20483 c=-24 a=-379
queue_step 4: t=12764705532893 p=82976 i=12668 c=-41 a=-110
queue_step 5: t=12764705958093 p=82935 i=8680 c=-75 a=-36
queue_step 6: t=12764706506764 p=82860 i=6251 c=-105 a=-15
queue_step 7: t=12764707079822 p=82755 i=4854 c=-120 a=-8
queue_step 8: t=12764707604351 p=82635 i=4023 c=-130 a=-5
queue_step 9: t=12764708084847 p=82505 i=3454 c=-182 a=-3
queue_step 10: t=12764708663575 p=82323 i=2967 c=-200 a=-2
queue_step 11: t=12764709216847 p=82123 i=2639 c=-120 a=-2
queue_step 12: t=12764709519049 p=82003 i=2441 c=-141 a=-1
queue_step 13: t=12764709853206 p=81862 i=2287 c=-168 a=-1
queue_step 14: t=12764710223264 p=81694 i=2157 c=-170 a=-1
queue_step 15: t=12764710575468 p=81524 i=2036 c=-140 a=-1
queue_step 16: t=12764710850692 p=81384 i=1950 c=-127 a=-1
queue_step 17: t=12764711090271 p=81257 i=1880 c=-116 a=-1
queue_step 18: t=12764711301624 p=81141 i=1823 c=-111 a=-1
queue_step 19: t=12764711497822 p=81030 i=1773 c=-106 a=-1
queue_step 20: t=12764711680150 p=80924 i=1728 c=-101 a=-1
queue_step 21: t=12764711849589 p=80823 i=1689 c=-99 a=-1
queue_step 22: t=12764712011913 p=80724 i=1653 c=-96 a=-1
queue_step 23: t=12764712166009 p=80628 i=1621 c=-96 a=-1
queue_step 24: t=12764712317034 p=80532 i=1590 c=-93 a=-1
queue_step 25: t=12764712460597 p=80439 i=1561 c=-90 a=-1
queue_step 26: t=12764712597056 p=80349 i=1535 c=-88 a=-1
queue_step 27: t=12764712728250 p=80261 i=1477 c=-83 a=0
queue_step 28: t=12764712850803 p=80178 i=1439 c=-147 a=0
queue_step 29: t=12764713062301 p=80031 i=1404 c=-147 a=0
queue_step 30: t=12764713268656 p=79884 i=1371 c=-150 a=0
queue_step 31: t=12764713474274 p=79734 i=1339 c=-161 a=0
queue_step 32: t=12764713689822 p=79573 i=1308 c=-160 a=0
queue_step 33: t=12764713899073 p=79413 i=1279 c=-164 a=0
queue_step 34: t=12764714108801 p=79249 i=1251 c=-168 a=0
queue_step 35: t=12764714318942 p=79081 i=1224 c=-176 a=0
queue_step 36: t=12764714534340 p=78905 i=1198 c=-177 a=0
queue_step 37: t=12764714746361 p=78728 i=1173 c=-183 a=0
queue_step 38: t=12764714960996 p=78545 i=1149 c=-188 a=0
queue_step 39: t=12764715176985 p=78357 i=1126 c=-188 a=0
queue_step 40: t=12764715388651 p=78169 i=1104 c=-194 a=0
queue_step 41: t=12764715602806 p=77975 i=1083 c=-193 a=0
queue_step 42: t=12764715811805 p=77782 i=1063 c=-197 a=0
queue_step 43: t=12764716021197 p=77585 i=1044 c=-194 a=0
queue_step 44: t=12764716223715 p=77391 i=1026 c=-197 a=0
queue_step 45: t=12764716425819 p=77194 i=1008 c=-216 a=0
queue_step 46: t=12764716643529 p=76978 i=990 c=-219 a=0
queue_step 47: t=12764716860322 p=76759 i=973 c=-213 a=0
queue_step 48: t=12764717067555 p=76546 i=957 c=-217 a=0
queue_step 49: t=12764717275209 p=76329 i=942 c=-204 a=0
queue_step 50: t=12764717467363 p=76125 i=928 c=-209 a=0
queue_step 51: t=12764717661301 p=75916 i=914 c=-223 a=0
queue_step 52: t=12764717865109 p=75693 i=900 c=-228 a=0
queue_step 53: t=12764718070296 p=75465 i=887 c=-212 a=0
queue_step 54: t=12764718258327 p=75253 i=874 c=-246 a=0
queue_step 55: t=12764718473318 p=75007 i=861 c=-234 a=0
queue_step 56: t=12764718674780 p=74773 i=849 c=-229 a=0
queue_step 57: t=12764718869189 p=74544 i=837 c=-253 a=0
queue_step 58: t=12764719080938 p=74291 i=825 c=-250 a=0
queue_step 59: t=12764719287177 p=74041 i=814 c=-232 a=0
queue_step 60: t=12764719476014 p=73809 i=803 c=-2173 a=0
queue_step 61: t=12764721220932 p=71636 i=802 c=-498 a=0
queue_step 62: t=12764721620329 p=71138 i=803 c=-2073 a=0
queue_step 63: t=12764723284947 p=69065 i=802 c=-498 a=0
queue_step 64: t=12764723684344 p=68567 i=803 c=-2073 a=0
queue_step 65: t=12764725348962 p=66494 i=802 c=-498 a=0
queue_step 66: t=12764725748359 p=65996 i=803 c=-2073 a=0
queue_step 67: t=12764727412977 p=63923 i=802 c=-498 a=0
queue_step 68: t=12764727812374 p=63425 i=803 c=-2072 a=0
queue_step 69: t=12764729476189 p=61353 i=802 c=-498 a=0
queue_step 70: t=12764729875586 p=60855 i=803 c=-2073 a=0
queue_step 71: t=12764731540204 p=58782 i=802 c=-498 a=0
queue_step 72: t=12764731939601 p=58284 i=803 c=-2073 a=0
Dumping stepper 'stepper_y' (mcu) 63 queue_step:
queue_step 0: t=12764704701509 p=-83021 i=565437955 c=1 a=0
queue_step 1: t=12764704781155 p=-83020 i=79646 c=3 a=-17757
queue_step 2: t=12764704926036 p=-83017 i=38860 c=8 a=-2281
queue_step 3: t=12764705156303 p=-83009 i=22115 c=22 a=-432
queue_step 4: t=12764705534432 p=-82987 i=13506 c=45 a=-112
queue_step 5: t=12764706026818 p=-82942 i=9002 c=75 a=-37
queue_step 6: t=12764706596808 p=-82867 i=6517 c=100 a=-16
queue_step 7: t=12764707167874 p=-82767 i=5083 c=133 a=-8
queue_step 8: t=12764707772753 p=-82634 i=4147 c=134 a=-5
queue_step 9: t=12764708283306 p=-82500 i=3557 c=186 a=-3
queue_step 10: t=12764708892794 p=-82314 i=3058 c=209 a=-2
queue_step 11: t=12764709488100 p=-82105 i=2714 c=122 a=-2
queue_step 12: t=12764709804243 p=-81983 i=2511 c=157 a=-1
queue_step 13: t=12764710186055 p=-81826 i=2342 c=162 a=-1
queue_step 14: t=12764710552295 p=-81664 i=2219 c=174 a=-1
queue_step 15: t=12764710923226 p=-81490 i=2095 c=144 a=-1
queue_step 16: t=12764711214521 p=-81346 i=2006 c=128 a=-1
queue_step 17: t=12764711463091 p=-81218 i=1936 c=120 a=-1
queue_step 18: t=12764711688212 p=-81098 i=1877 c=115 a=-1
queue_step 19: t=12764711897459 p=-80983 i=1824 c=107 a=-1
queue_step 20: t=12764712086912 p=-80876 i=1780 c=106 a=-1
queue_step 21: t=12764712269985 p=-80770 i=1738 c=100 a=-1
queue_step 22: t=12764712438799 p=-80670 i=1702 c=99 a=-1
queue_step 23: t=12764712602412 p=-80571 i=1668 c=96 a=-1
queue_step 24: t=12764712757949 p=-80475 i=1637 c=94 a=-1
queue_step 25: t=12764712907427 p=-80381 i=1608 c=92 a=-1
queue_step 26: t=12764713051115 p=-80289 i=1546 c=85 a=0
queue_step 27: t=12764713182485 p=-80204 i=1506 c=149 a=0
queue_step 28: t=12764713406841 p=-80055 i=1468 c=154 a=0
queue_step 29: t=12764713632877 p=-79901 i=1432 c=156 a=0
queue_step 30: t=12764713856235 p=-79745 i=1398 c=159 a=0
queue_step 31: t=12764714078485 p=-79586 i=1366 c=159 a=0
queue_step 32: t=12764714295648 p=-79427 i=1335 c=170 a=0
queue_step 33: t=12764714522568 p=-79257 i=1305 c=173 a=0
queue_step 34: t=12764714748305 p=-79084 i=1277 c=168 a=0
queue_step 35: t=12764714962815 p=-78916 i=1251 c=170 a=0
queue_step 36: t=12764715175460 p=-78746 i=1226 c=175 a=0
queue_step 37: t=12764715389986 p=-78571 i=1202 c=177 a=0
queue_step 38: t=12764715602717 p=-78394 i=1179 c=180 a=0
queue_step 39: t=12764715814915 p=-78214 i=1157 c=183 a=0
queue_step 40: t=12764716026624 p=-78031 i=1135 c=200 a=0
queue_step 41: t=12764716253603 p=-77831 i=1114 c=187 a=0
queue_step 42: t=12764716461901 p=-77644 i=1094 c=203 a=0
queue_step 43: t=12764716683963 p=-77441 i=1074 c=209 a=0
queue_step 44: t=12764716908410 p=-77232 i=1055 c=203 a=0
queue_step 45: t=12764717122557 p=-77029 i=1037 c=211 a=0
queue_step 46: t=12764717341346 p=-76818 i=1019 c=223 a=0
queue_step 47: t=12764717568566 p=-76595 i=1002 c=209 a=0
queue_step 48: t=12764717777968 p=-76386 i=986 c=218 a=0
queue_step 49: t=12764717992900 p=-76168 i=970 c=231 a=0
queue_step 50: t=12764718216955 p=-75937 i=955 c=210 a=0
queue_step 51: t=12764718417491 p=-75727 i=941 c=221 a=0
queue_step 52: t=12764718625438 p=-75506 i=927 c=230 a=0
queue_step 53: t=12764718838634 p=-75276 i=913 c=241 a=0
queue_step 54: t=12764719058653 p=-75035 i=899 c=253 a=0
queue_step 55: t=12764719286087 p=-74782 i=886 c=226 a=0
queue_step 56: t=12764719486311 p=-74556 i=874 c=929 a=0
queue_step 57: t=12764720298258 p=-73627 i=875 c=484 a=0
queue_step 58: t=12764720721757 p=-73143 i=874 c=4582 a=0
queue_step 59: t=12764724726426 p=-68561 i=875 c=484 a=0
queue_step 60: t=12764725149925 p=-68077 i=874 c=4582 a=0
queue_step 61: t=12764729154594 p=-63495 i=875 c=484 a=0
queue_step 62: t=12764729578093 p=-63011 i=874 c=4582 a=0
Dumping stepper 'stepper_y1' (mcu) 63 queue_step:
queue_step 0: t=12764704701509 p=-83021 i=565437955 c=1 a=0
queue_step 1: t=12764704781155 p=-83020 i=79646 c=3 a=-17757
queue_step 2: t=12764704926036 p=-83017 i=38860 c=8 a=-2281
queue_step 3: t=12764705156303 p=-83009 i=22115 c=22 a=-432
queue_step 4: t=12764705534432 p=-82987 i=13506 c=45 a=-112
queue_step 5: t=12764706026818 p=-82942 i=9002 c=75 a=-37
queue_step 6: t=12764706596808 p=-82867 i=6517 c=100 a=-16
queue_step 7: t=12764707167874 p=-82767 i=5083 c=133 a=-8
queue_step 8: t=12764707772753 p=-82634 i=4147 c=134 a=-5
queue_step 9: t=12764708283306 p=-82500 i=3557 c=186 a=-3
queue_step 10: t=12764708892794 p=-82314 i=3058 c=209 a=-2
queue_step 11: t=12764709488100 p=-82105 i=2714 c=122 a=-2
queue_step 12: t=12764709804243 p=-81983 i=2511 c=157 a=-1
queue_step 13: t=12764710186055 p=-81826 i=2342 c=162 a=-1
queue_step 14: t=12764710552295 p=-81664 i=2219 c=174 a=-1
queue_step 15: t=12764710923226 p=-81490 i=2095 c=144 a=-1
queue_step 16: t=12764711214521 p=-81346 i=2006 c=128 a=-1
queue_step 17: t=12764711463091 p=-81218 i=1936 c=120 a=-1
queue_step 18: t=12764711688212 p=-81098 i=1877 c=115 a=-1
queue_step 19: t=12764711897459 p=-80983 i=1824 c=107 a=-1
queue_step 20: t=12764712086912 p=-80876 i=1780 c=106 a=-1
queue_step 21: t=12764712269985 p=-80770 i=1738 c=100 a=-1
queue_step 22: t=12764712438799 p=-80670 i=1702 c=99 a=-1
queue_step 23: t=12764712602412 p=-80571 i=1668 c=96 a=-1
queue_step 24: t=12764712757949 p=-80475 i=1637 c=94 a=-1
queue_step 25: t=12764712907427 p=-80381 i=1608 c=92 a=-1
queue_step 26: t=12764713051115 p=-80289 i=1546 c=85 a=0
queue_step 27: t=12764713182485 p=-80204 i=1506 c=149 a=0
queue_step 28: t=12764713406841 p=-80055 i=1468 c=154 a=0
queue_step 29: t=12764713632877 p=-79901 i=1432 c=156 a=0
queue_step 30: t=12764713856235 p=-79745 i=1398 c=159 a=0
queue_step 31: t=12764714078485 p=-79586 i=1366 c=159 a=0
queue_step 32: t=12764714295648 p=-79427 i=1335 c=170 a=0
queue_step 33: t=12764714522568 p=-79257 i=1305 c=173 a=0
queue_step 34: t=12764714748305 p=-79084 i=1277 c=168 a=0
queue_step 35: t=12764714962815 p=-78916 i=1251 c=170 a=0
queue_step 36: t=12764715175460 p=-78746 i=1226 c=175 a=0
queue_step 37: t=12764715389986 p=-78571 i=1202 c=177 a=0
queue_step 38: t=12764715602717 p=-78394 i=1179 c=180 a=0
queue_step 39: t=12764715814915 p=-78214 i=1157 c=183 a=0
queue_step 40: t=12764716026624 p=-78031 i=1135 c=200 a=0
queue_step 41: t=12764716253603 p=-77831 i=1114 c=187 a=0
queue_step 42: t=12764716461901 p=-77644 i=1094 c=203 a=0
queue_step 43: t=12764716683963 p=-77441 i=1074 c=209 a=0
queue_step 44: t=12764716908410 p=-77232 i=1055 c=203 a=0
queue_step 45: t=12764717122557 p=-77029 i=1037 c=211 a=0
queue_step 46: t=12764717341346 p=-76818 i=1019 c=223 a=0
queue_step 47: t=12764717568566 p=-76595 i=1002 c=209 a=0
queue_step 48: t=12764717777968 p=-76386 i=986 c=218 a=0
queue_step 49: t=12764717992900 p=-76168 i=970 c=231 a=0
queue_step 50: t=12764718216955 p=-75937 i=955 c=210 a=0
queue_step 51: t=12764718417491 p=-75727 i=941 c=221 a=0
queue_step 52: t=12764718625438 p=-75506 i=927 c=230 a=0
queue_step 53: t=12764718838634 p=-75276 i=913 c=241 a=0
queue_step 54: t=12764719058653 p=-75035 i=899 c=253 a=0
queue_step 55: t=12764719286087 p=-74782 i=886 c=226 a=0
queue_step 56: t=12764719486311 p=-74556 i=874 c=929 a=0
queue_step 57: t=12764720298258 p=-73627 i=875 c=484 a=0
queue_step 58: t=12764720721757 p=-73143 i=874 c=4582 a=0
queue_step 59: t=12764724726426 p=-68561 i=875 c=484 a=0
queue_step 60: t=12764725149925 p=-68077 i=874 c=4582 a=0
queue_step 61: t=12764729154594 p=-63495 i=875 c=484 a=0
queue_step 62: t=12764729578093 p=-63011 i=874 c=4582 a=0
Dumping stepper 'stepper_z' (mcu) 49 queue_step:
queue_step 0: t=12764704751321 p=49956 i=656419653 c=-1 a=0
queue_step 1: t=12764704829202 p=49955 i=77881 c=-3 a=-13280
queue_step 2: t=12764704986022 p=49952 i=40898 c=-10 a=-1937
queue_step 3: t=12764705290220 p=49942 i=23281 c=-23 a=-413
queue_step 4: t=12764705712628 p=49919 i=14715 c=-45 a=-117
queue_step 5: t=12764706254323 p=49874 i=10065 c=-71 a=-42
queue_step 6: t=12764706861905 p=49803 i=7402 c=-102 a=-18
queue_step 7: t=12764707522539 p=49701 i=5750 c=-133 a=-9
queue_step 8: t=12764708207203 p=49568 i=4666 c=-170 a=-5
queue_step 9: t=12764708927826 p=49398 i=3894 c=-209 a=-3
queue_step 10: t=12764709675898 p=49189 i=3328 c=-220 a=-2
queue_step 11: t=12764710359513 p=48969 i=2963 c=-129 a=-2
queue_step 12: t=12764710725014 p=48840 i=2749 c=-131 a=-1
queue_step 13: t=12764711076469 p=48709 i=2600 c=-221 a=-1
queue_step 14: t=12764711626578 p=48488 i=2419 c=-186 a=-1
queue_step 15: t=12764712059173 p=48302 i=2285 c=-153 a=-1
queue_step 16: t=12764712397055 p=48149 i=2190 c=-138 a=-1
queue_step 17: t=12764712689745 p=48011 i=2113 c=-126 a=-1
queue_step 18: t=12764712948045 p=47885 i=2050 c=-120 a=-1
queue_step 19: t=12764713186849 p=47765 i=1994 c=-113 a=-1
queue_step 20: t=12764713405795 p=47652 i=1946 c=-110 a=-1
queue_step 21: t=12764713613816 p=47542 i=1902 c=-105 a=-1
queue_step 22: t=12764713808027 p=47437 i=1863 c=-103 a=-1
queue_step 23: t=12764713994627 p=47334 i=1827 c=-100 a=-1
queue_step 24: t=12764714172344 p=47234 i=1794 c=-99 a=-1
queue_step 25: t=12764714345068 p=47135 i=1763 c=-97 a=-1
queue_step 26: t=12764714511394 p=47038 i=1734 c=-95 a=-1
queue_step 27: t=12764714671632 p=46943 i=1707 c=-93 a=-1
queue_step 28: t=12764714826044 p=46850 i=1646 c=-87 a=0
queue_step 29: t=12764714969206 p=46763 i=1606 c=-158 a=0
queue_step 30: t=12764715222916 p=46605 i=1568 c=-163 a=0
queue_step 31: t=12764715478464 p=46442 i=1532 c=-163 a=0
queue_step 32: t=12764715728146 p=46279 i=1498 c=-168 a=0
queue_step 33: t=12764715979777 p=46111 i=1465 c=-174 a=0
queue_step 34: t=12764716234656 p=45937 i=1434 c=-169 a=0
queue_step 35: t=12764716476973 p=45768 i=1405 c=-174 a=0
queue_step 36: t=12764716721415 p=45594 i=1377 c=-177 a=0
queue_step 37: t=12764716965117 p=45417 i=1350 c=-183 a=0
queue_step 38: t=12764717212141 p=45234 i=1324 c=-184 a=0
queue_step 39: t=12764717455732 p=45050 i=1299 c=-190 a=0
queue_step 40: t=12764717702518 p=44860 i=1275 c=-189 a=0
queue_step 41: t=12764717943470 p=44671 i=1252 c=-197 a=0
queue_step 42: t=12764718190091 p=44474 i=1229 c=-210 a=0
queue_step 43: t=12764718448159 p=44264 i=1207 c=-200 a=0
queue_step 44: t=12764718689538 p=44064 i=1186 c=-215 a=0
queue_step 45: t=12764718944507 p=43849 i=1165 c=-221 a=0
queue_step 46: t=12764719201952 p=43628 i=1145 c=-217 a=0
queue_step 47: t=12764719450398 p=43411 i=1126 c=-632 a=0
queue_step 48: t=12764720162029 p=42779 i=1125 c=-50286 a=0
Dumping stepper 'stepper_z1' (mcu) 49 queue_step:
queue_step 0: t=12764704751321 p=50165 i=656419653 c=-1 a=0
queue_step 1: t=12764704829202 p=50164 i=77881 c=-3 a=-13280
queue_step 2: t=12764704986022 p=50161 i=40898 c=-10 a=-1937
queue_step 3: t=12764705290220 p=50151 i=23281 c=-23 a=-413
queue_step 4: t=12764705712628 p=50128 i=14715 c=-45 a=-117
queue_step 5: t=12764706254323 p=50083 i=10065 c=-71 a=-42
queue_step 6: t=12764706861905 p=50012 i=7402 c=-102 a=-18
queue_step 7: t=12764707522539 p=49910 i=5750 c=-133 a=-9
queue_step 8: t=12764708207203 p=49777 i=4666 c=-170 a=-5
queue_step 9: t=12764708927826 p=49607 i=3894 c=-209 a=-3
queue_step 10: t=12764709675898 p=49398 i=3328 c=-220 a=-2
queue_step 11: t=12764710359513 p=49178 i=2963 c=-129 a=-2
queue_step 12: t=12764710725014 p=49049 i=2749 c=-131 a=-1
queue_step 13: t=12764711076469 p=48918 i=2600 c=-221 a=-1
queue_step 14: t=12764711626578 p=48697 i=2419 c=-186 a=-1
queue_step 15: t=12764712059173 p=48511 i=2285 c=-153 a=-1
queue_step 16: t=12764712397055 p=48358 i=2190 c=-138 a=-1
queue_step 17: t=12764712689745 p=48220 i=2113 c=-126 a=-1
queue_step 18: t=12764712948045 p=48094 i=2050 c=-120 a=-1
queue_step 19: t=12764713186849 p=47974 i=1994 c=-113 a=-1
queue_step 20: t=12764713405795 p=47861 i=1946 c=-110 a=-1
queue_step 21: t=12764713613816 p=47751 i=1902 c=-105 a=-1
queue_step 22: t=12764713808027 p=47646 i=1863 c=-103 a=-1
queue_step 23: t=12764713994627 p=47543 i=1827 c=-100 a=-1
queue_step 24: t=12764714172344 p=47443 i=1794 c=-99 a=-1
queue_step 25: t=12764714345068 p=47344 i=1763 c=-97 a=-1
queue_step 26: t=12764714511394 p=47247 i=1734 c=-95 a=-1
queue_step 27: t=12764714671632 p=47152 i=1707 c=-93 a=-1
queue_step 28: t=12764714826044 p=47059 i=1646 c=-87 a=0
queue_step 29: t=12764714969206 p=46972 i=1606 c=-158 a=0
queue_step 30: t=12764715222916 p=46814 i=1568 c=-163 a=0
queue_step 31: t=12764715478464 p=46651 i=1532 c=-163 a=0
queue_step 32: t=12764715728146 p=46488 i=1498 c=-168 a=0
queue_step 33: t=12764715979777 p=46320 i=1465 c=-174 a=0
queue_step 34: t=12764716234656 p=46146 i=1434 c=-169 a=0
queue_step 35: t=12764716476973 p=45977 i=1405 c=-174 a=0
queue_step 36: t=12764716721415 p=45803 i=1377 c=-177 a=0
queue_step 37: t=12764716965117 p=45626 i=1350 c=-183 a=0
queue_step 38: t=12764717212141 p=45443 i=1324 c=-184 a=0
queue_step 39: t=12764717455732 p=45259 i=1299 c=-190 a=0
queue_step 40: t=12764717702518 p=45069 i=1275 c=-189 a=0
queue_step 41: t=12764717943470 p=44880 i=1252 c=-197 a=0
queue_step 42: t=12764718190091 p=44683 i=1229 c=-210 a=0
queue_step 43: t=12764718448159 p=44473 i=1207 c=-200 a=0
queue_step 44: t=12764718689538 p=44273 i=1186 c=-215 a=0
queue_step 45: t=12764718944507 p=44058 i=1165 c=-221 a=0
queue_step 46: t=12764719201952 p=43837 i=1145 c=-217 a=0
queue_step 47: t=12764719450398 p=43620 i=1126 c=-632 a=0
queue_step 48: t=12764720162029 p=42988 i=1125 c=-50286 a=0
Dumping stepper 'stepper_z2' (mcu) 49 queue_step:
queue_step 0: t=12764704751321 p=50167 i=656419653 c=-1 a=0
queue_step 1: t=12764704829202 p=50166 i=77881 c=-3 a=-13280
queue_step 2: t=12764704986022 p=50163 i=40898 c=-10 a=-1937
queue_step 3: t=12764705290220 p=50153 i=23281 c=-23 a=-413
queue_step 4: t=12764705712628 p=50130 i=14715 c=-45 a=-117
queue_step 5: t=12764706254323 p=50085 i=10065 c=-71 a=-42
queue_step 6: t=12764706861905 p=50014 i=7402 c=-102 a=-18
queue_step 7: t=12764707522539 p=49912 i=5750 c=-133 a=-9
queue_step 8: t=12764708207203 p=49779 i=4666 c=-170 a=-5
queue_step 9: t=12764708927826 p=49609 i=3894 c=-209 a=-3
queue_step 10: t=12764709675898 p=49400 i=3328 c=-220 a=-2
queue_step 11: t=12764710359513 p=49180 i=2963 c=-129 a=-2
queue_step 12: t=12764710725014 p=49051 i=2749 c=-131 a=-1
queue_step 13: t=12764711076469 p=48920 i=2600 c=-221 a=-1
queue_step 14: t=12764711626578 p=48699 i=2419 c=-186 a=-1
queue_step 15: t=12764712059173 p=48513 i=2285 c=-153 a=-1
queue_step 16: t=12764712397055 p=48360 i=2190 c=-138 a=-1
queue_step 17: t=12764712689745 p=48222 i=2113 c=-126 a=-1
queue_step 18: t=12764712948045 p=48096 i=2050 c=-120 a=-1
queue_step 19: t=12764713186849 p=47976 i=1994 c=-113 a=-1
queue_step 20: t=12764713405795 p=47863 i=1946 c=-110 a=-1
queue_step 21: t=12764713613816 p=47753 i=1902 c=-105 a=-1
queue_step 22: t=12764713808027 p=47648 i=1863 c=-103 a=-1
queue_step 23: t=12764713994627 p=47545 i=1827 c=-100 a=-1
queue_step 24: t=12764714172344 p=47445 i=1794 c=-99 a=-1
queue_step 25: t=12764714345068 p=47346 i=1763 c=-97 a=-1
queue_step 26: t=12764714511394 p=47249 i=1734 c=-95 a=-1
queue_step 27: t=12764714671632 p=47154 i=1707 c=-93 a=-1
queue_step 28: t=12764714826044 p=47061 i=1646 c=-87 a=0
queue_step 29: t=12764714969206 p=46974 i=1606 c=-158 a=0
queue_step 30: t=12764715222916 p=46816 i=1568 c=-163 a=0
queue_step 31: t=12764715478464 p=46653 i=1532 c=-163 a=0
queue_step 32: t=12764715728146 p=46490 i=1498 c=-168 a=0
queue_step 33: t=12764715979777 p=46322 i=1465 c=-174 a=0
queue_step 34: t=12764716234656 p=46148 i=1434 c=-169 a=0
queue_step 35: t=12764716476973 p=45979 i=1405 c=-174 a=0
queue_step 36: t=12764716721415 p=45805 i=1377 c=-177 a=0
queue_step 37: t=12764716965117 p=45628 i=1350 c=-183 a=0
queue_step 38: t=12764717212141 p=45445 i=1324 c=-184 a=0
queue_step 39: t=12764717455732 p=45261 i=1299 c=-190 a=0
queue_step 40: t=12764717702518 p=45071 i=1275 c=-189 a=0
queue_step 41: t=12764717943470 p=44882 i=1252 c=-197 a=0
queue_step 42: t=12764718190091 p=44685 i=1229 c=-210 a=0
queue_step 43: t=12764718448159 p=44475 i=1207 c=-200 a=0
queue_step 44: t=12764718689538 p=44275 i=1186 c=-215 a=0
queue_step 45: t=12764718944507 p=44060 i=1165 c=-221 a=0
queue_step 46: t=12764719201952 p=43839 i=1145 c=-217 a=0
queue_step 47: t=12764719450398 p=43622 i=1126 c=-632 a=0
queue_step 48: t=12764720162029 p=42990 i=1125 c=-50286 a=0
Dumping stepper 'extruder' (toolboard_t0) 25 queue_step:
queue_step 0: t=4538626263006 p=-144115 i=687 c=172 a=0
queue_step 1: t=4538626381158 p=-143943 i=675 c=207 a=0
queue_step 2: t=4538626520876 p=-143736 i=668 c=489 a=0
queue_step 3: t=4538626847538 p=-143247 i=678 c=214 a=0
queue_step 4: t=4538626992644 p=-143033 i=692 c=166 a=0
queue_step 5: t=4538627107533 p=-142867 i=709 c=141 a=0
queue_step 6: t=4538627207522 p=-142726 i=729 c=121 a=0
queue_step 7: t=4538627295754 p=-142605 i=752 c=109 a=0
queue_step 8: t=4538627377749 p=-142496 i=779 c=101 a=0
queue_step 9: t=4538627456459 p=-142395 i=810 c=92 a=0
queue_step 10: t=4538627531015 p=-142303 i=846 c=86 a=0
queue_step 11: t=4538627603812 p=-142217 i=887 c=76 a=0
queue_step 12: t=4538627671271 p=-142141 i=934 c=72 a=0
queue_step 13: t=4538627738543 p=-142069 i=958 c=179 a=1
queue_step 14: t=4538627926180 p=-141890 i=1182 c=78 a=1
queue_step 15: t=4538628021515 p=-141812 i=1318 c=87 a=2
queue_step 16: t=4538628143896 p=-141725 i=1551 c=87 a=4
queue_step 17: t=4538628294215 p=-141638 i=1969 c=74 a=9
queue_step 18: t=4538628464991 p=-141564 i=2730 c=54 a=24
queue_step 19: t=4538628648286 p=-141510 i=4261 c=30 a=69
queue_step 20: t=4538628808606 p=-141480 i=6736 c=17 a=218
queue_step 21: t=4538628957240 p=-141463 i=11210 c=9 a=747
queue_step 22: t=4538629093014 p=-141454 i=19202 c=5 a=2879
queue_step 23: t=4538629238398 p=-141449 i=39786 c=2 a=12925
queue_step 24: t=4538629371911 p=-141447 i=80802 c=1 a=0
Dumping trapq 'toolhead' 2 moves:
move 0: pt=70915.025483 mt=0.083333 sv=0.000000 a=7775.838209 sp=(250.000000,-9.350000,20.599156) ar=(-0.088188,0.993111,-0.077162)
move 1: pt=70915.108817 mt=0.316757 sv=647.986517 a=0.000000 sp=(247.618965,17.463431,18.515823) ar=(-0.088188,0.993111,-0.077162)
Dumping trapq 'extruder' 3 moves:
move 0: pt=70914.969472 mt=0.013154 sv=0.000000 a=2660.810804 sp=(92.336470,0.000000,0.000000) ar=(1.000000,0.000000,0.000000)
move 1: pt=70914.982626 mt=0.029703 sv=35.000000 a=0.000000 sp=(92.566663,0.000000,0.000000) ar=(1.000000,0.000000,0.000000)
move 2: pt=70915.012329 mt=0.013154 sv=35.000000 a=-2660.810804 sp=(93.606277,0.000000,0.000000) ar=(1.000000,0.000000,0.000000)
Requested toolhead position at shutdown time 70915.080570: (248.95955195398307, 2.366747435410449, 19.688795660559716)
Stats 70909.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000034 mcu_task_stddev=0.000097 bytes_write=1207897 bytes_read=8202876 bytes_retransmit=9 bytes_invalid=0 send_seq=90412 receive_seq=90412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11820 freq=179999343 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=420900 bytes_read=1297938 bytes_retransmit=0 bytes_invalid=0 send_seq=70117 receive_seq=70117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015493 adj=50003931 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=554479 bytes_read=7766122 bytes_retransmit=9 bytes_invalid=0 send_seq=74206 receive_seq=74206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999348 adj=63999540 Octopus_V1.1_F446: temp=34.0 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=36.0 sd_pos=148171 heater_bed: target=55 temp=55.1 pwm=0.270 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452305 bytes_read=24629793 bytes_retransmit=9 bytes_invalid=0 send_seq=72763 receive_seq=72763 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999640 coil_temp=37.4 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.17 cputime=3414.957 memavail=1405212 print_time=70917.604 buffer_time=2.368 print_stall=0 extruder: target=220 temp=222.7 pwm=0.000
Exiting SD card print (position 148199)
Stats 70910.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000034 mcu_task_stddev=0.000097 bytes_write=1219045 bytes_read=8214001 bytes_retransmit=9 bytes_invalid=0 send_seq=90596 receive_seq=90596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=13 upcoming_bytes=1662 freq=179999346 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=420906 bytes_read=1297954 bytes_retransmit=0 bytes_invalid=0 send_seq=70118 receive_seq=70118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015418 adj=50012995 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=554513 bytes_read=7766249 bytes_retransmit=9 bytes_invalid=0 send_seq=74209 receive_seq=74209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999345 adj=63999545 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=37.1 raspberry_pi: temp=35.5  heater_bed: target=55 temp=55.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452311 bytes_read=24630149 bytes_retransmit=9 bytes_invalid=0 send_seq=72764 receive_seq=72764 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999568 adj=31999666 coil_temp=37.4 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.17 cputime=3415.043 memavail=1405304 print_time=70917.604 buffer_time=1.368 print_stall=0 extruder: target=220 temp=219.9 pwm=0.000
Stats 70911.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000034 mcu_task_stddev=0.000097 bytes_write=1220899 bytes_read=8215918 bytes_retransmit=9 bytes_invalid=0 send_seq=90628 receive_seq=90628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999344 rpi: mcu_awake=0.001 mcu_task_avg=0.000011 mcu_task_stddev=0.000014 bytes_write=420912 bytes_read=1297970 bytes_retransmit=0 bytes_invalid=0 send_seq=70119 receive_seq=70119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015348 adj=50012113 toolboard_t0: mcu_awake=0.009 mcu_task_avg=0.000029 mcu_task_stddev=0.000036 bytes_write=554547 bytes_read=7766376 bytes_retransmit=9 bytes_invalid=0 send_seq=74212 receive_seq=74212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999344 adj=63999501 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=36.9 raspberry_pi: temp=36.0  heater_bed: target=55 temp=55.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452317 bytes_read=24630505 bytes_retransmit=9 bytes_invalid=0 send_seq=72765 receive_seq=72765 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999567 adj=31999658 coil_temp=37.3 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.17 cputime=3415.078 memavail=1405304 print_time=70917.604 buffer_time=0.367 print_stall=0 extruder: target=220 temp=216.9 pwm=0.000
Stats 70912.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000034 mcu_task_stddev=0.000097 bytes_write=1221169 bytes_read=8216304 bytes_retransmit=9 bytes_invalid=0 send_seq=90635 receive_seq=90635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999339 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420918 bytes_read=1297999 bytes_retransmit=0 bytes_invalid=0 send_seq=70120 receive_seq=70120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015279 adj=50011319 toolboard_t0: mcu_awake=0.013 mcu_task_avg=0.000036 mcu_task_stddev=0.000039 bytes_write=554742 bytes_read=7766694 bytes_retransmit=9 bytes_invalid=0 send_seq=74218 receive_seq=74218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999341 adj=63999488 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=37.0 raspberry_pi: temp=35.5  heater_bed: target=55 temp=55.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452323 bytes_read=24630861 bytes_retransmit=9 bytes_invalid=0 send_seq=72766 receive_seq=72766 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999567 adj=31999650 coil_temp=37.2 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.17 cputime=3415.118 memavail=1405304 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=214.4 pwm=0.000
Stats 70913.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000022 mcu_task_stddev=0.000060 bytes_write=1221203 bytes_read=8216448 bytes_retransmit=9 bytes_invalid=0 send_seq=90638 receive_seq=90638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999339 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420924 bytes_read=1298015 bytes_retransmit=0 bytes_invalid=0 send_seq=70121 receive_seq=70121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015200 adj=50010464 toolboard_t0: mcu_awake=0.013 mcu_task_avg=0.000036 mcu_task_stddev=0.000039 bytes_write=554776 bytes_read=7766836 bytes_retransmit=9 bytes_invalid=0 send_seq=74221 receive_seq=74221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999349 adj=63999483 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.8 raspberry_pi: temp=35.0  heater_bed: target=55 temp=55.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452335 bytes_read=24631233 bytes_retransmit=9 bytes_invalid=0 send_seq=72768 receive_seq=72768 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999652 coil_temp=37.2 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.17 cputime=3415.177 memavail=1405304 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=211.2 pwm=0.000
Stats 70914.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000022 mcu_task_stddev=0.000060 bytes_write=1221237 bytes_read=8216575 bytes_retransmit=9 bytes_invalid=0 send_seq=90641 receive_seq=90641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999341 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420930 bytes_read=1298031 bytes_retransmit=0 bytes_invalid=0 send_seq=70122 receive_seq=70122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50015103 adj=50009252 toolboard_t0: mcu_awake=0.013 mcu_task_avg=0.000036 mcu_task_stddev=0.000039 bytes_write=554810 bytes_read=7766963 bytes_retransmit=9 bytes_invalid=0 send_seq=74224 receive_seq=74224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999349 adj=63999600 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=34.6  heater_bed: target=55 temp=55.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452341 bytes_read=24631589 bytes_retransmit=9 bytes_invalid=0 send_seq=72769 receive_seq=72769 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999715 coil_temp=37.1 refs=0 mcu_temp=35.39 supply_voltage=3.014 sysload=0.15 cputime=3415.235 memavail=1405052 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=209.1 pwm=0.000
Stats 70915.7: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000022 mcu_task_stddev=0.000060 bytes_write=1221271 bytes_read=8216731 bytes_retransmit=9 bytes_invalid=0 send_seq=90644 receive_seq=90644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999346 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420936 bytes_read=1298047 bytes_retransmit=0 bytes_invalid=0 send_seq=70123 receive_seq=70123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014996 adj=50008767 toolboard_t0: mcu_awake=0.013 mcu_task_avg=0.000036 mcu_task_stddev=0.000039 bytes_write=554816 bytes_read=7767080 bytes_retransmit=9 bytes_invalid=0 send_seq=74225 receive_seq=74225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999349 adj=63999573 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.7 raspberry_pi: temp=34.1  heater_bed: target=55 temp=55.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452347 bytes_read=24631945 bytes_retransmit=9 bytes_invalid=0 send_seq=72770 receive_seq=72770 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999698 coil_temp=37.0 refs=0 mcu_temp=35.31 supply_voltage=3.014 sysload=0.15 cputime=3415.293 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=206.8 pwm=0.000
Stats 70916.8: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000022 mcu_task_stddev=0.000060 bytes_write=1221305 bytes_read=8216858 bytes_retransmit=9 bytes_invalid=0 send_seq=90647 receive_seq=90647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999355 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=420942 bytes_read=1298063 bytes_retransmit=0 bytes_invalid=0 send_seq=70124 receive_seq=70124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014873 adj=50008623 toolboard_t0: mcu_awake=0.013 mcu_task_avg=0.000036 mcu_task_stddev=0.000039 bytes_write=554822 bytes_read=7767198 bytes_retransmit=9 bytes_invalid=0 send_seq=74226 receive_seq=74226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999347 adj=63999549 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.6 raspberry_pi: temp=34.1  heater_bed: target=55 temp=54.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452353 bytes_read=24632301 bytes_retransmit=9 bytes_invalid=0 send_seq=72771 receive_seq=72771 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999681 coil_temp=36.9 refs=0 mcu_temp=35.20 supply_voltage=3.014 sysload=0.15 cputime=3415.353 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=203.9 pwm=0.000
Stats 70917.8: gcodein=0  mcu: mcu_awake=0.024 mcu_task_avg=0.000022 mcu_task_stddev=0.000060 bytes_write=1221339 bytes_read=8216985 bytes_retransmit=9 bytes_invalid=0 send_seq=90650 receive_seq=90650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999359 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=420948 bytes_read=1298092 bytes_retransmit=0 bytes_invalid=0 send_seq=70125 receive_seq=70125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014740 adj=50008229 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=554828 bytes_read=7767316 bytes_retransmit=9 bytes_invalid=0 send_seq=74227 receive_seq=74227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999351 adj=63999490 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=36.4 raspberry_pi: temp=34.6  heater_bed: target=55 temp=54.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452359 bytes_read=24632657 bytes_retransmit=9 bytes_invalid=0 send_seq=72772 receive_seq=72772 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999656 coil_temp=36.9 refs=0 mcu_temp=35.07 supply_voltage=3.014 sysload=0.15 cputime=3415.410 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=201.8 pwm=0.000
Stats 70918.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221373 bytes_read=8217155 bytes_retransmit=9 bytes_invalid=0 send_seq=90653 receive_seq=90653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999359 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=420954 bytes_read=1298108 bytes_retransmit=0 bytes_invalid=0 send_seq=70126 receive_seq=70126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014597 adj=50007748 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=554834 bytes_read=7767433 bytes_retransmit=9 bytes_invalid=0 send_seq=74228 receive_seq=74228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999350 adj=63999547 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=36.2 raspberry_pi: temp=34.1  heater_bed: target=55 temp=54.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452365 bytes_read=24633013 bytes_retransmit=9 bytes_invalid=0 send_seq=72773 receive_seq=72773 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999643 coil_temp=36.8 refs=0 mcu_temp=34.92 supply_voltage=3.014 sysload=0.15 cputime=3415.469 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=199.7 pwm=0.000
Stats 70919.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221407 bytes_read=8217282 bytes_retransmit=9 bytes_invalid=0 send_seq=90656 receive_seq=90656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999358 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=420960 bytes_read=1298124 bytes_retransmit=0 bytes_invalid=0 send_seq=70127 receive_seq=70127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014448 adj=50007230 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=554840 bytes_read=7767551 bytes_retransmit=9 bytes_invalid=0 send_seq=74229 receive_seq=74229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999349 adj=63999533 Octopus_V1.1_F446: temp=33.8 EBB42_v1.2_T0: temp=36.1 raspberry_pi: temp=34.6  heater_bed: target=55 temp=54.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452371 bytes_read=24633369 bytes_retransmit=9 bytes_invalid=0 send_seq=72774 receive_seq=72774 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999645 coil_temp=36.7 refs=0 mcu_temp=34.78 supply_voltage=3.014 sysload=0.14 cputime=3415.526 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=197.1 pwm=0.000
Stats 70920.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221441 bytes_read=8217409 bytes_retransmit=9 bytes_invalid=0 send_seq=90659 receive_seq=90659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999371 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=420966 bytes_read=1298140 bytes_retransmit=0 bytes_invalid=0 send_seq=70128 receive_seq=70128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014292 adj=50006700 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000016 mcu_task_stddev=0.000017 bytes_write=554846 bytes_read=7767654 bytes_retransmit=9 bytes_invalid=0 send_seq=74230 receive_seq=74230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999348 adj=63999538 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=35.0  heater_bed: target=55 temp=54.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452377 bytes_read=24633725 bytes_retransmit=9 bytes_invalid=0 send_seq=72775 receive_seq=72775 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999655 coil_temp=36.6 refs=0 mcu_temp=34.57 supply_voltage=3.014 sysload=0.14 cputime=3415.582 memavail=1404840 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=195.0 pwm=0.000
Stats 70921.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221475 bytes_read=8217565 bytes_retransmit=9 bytes_invalid=0 send_seq=90662 receive_seq=90662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999369 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000017 bytes_write=420972 bytes_read=1298156 bytes_retransmit=0 bytes_invalid=0 send_seq=70129 receive_seq=70129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50014132 adj=50006098 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554852 bytes_read=7767785 bytes_retransmit=9 bytes_invalid=0 send_seq=74231 receive_seq=74231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999346 adj=63999460 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=36.0 raspberry_pi: temp=33.6  heater_bed: target=55 temp=54.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452383 bytes_read=24634081 bytes_retransmit=9 bytes_invalid=0 send_seq=72776 receive_seq=72776 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999647 coil_temp=36.6 refs=0 mcu_temp=34.45 supply_voltage=3.014 sysload=0.14 cputime=3415.640 memavail=1404856 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=192.9 pwm=0.000
Stats 70922.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221509 bytes_read=8217692 bytes_retransmit=9 bytes_invalid=0 send_seq=90665 receive_seq=90665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999366 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=420978 bytes_read=1298185 bytes_retransmit=0 bytes_invalid=0 send_seq=70130 receive_seq=70130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013964 adj=50005605 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554858 bytes_read=7767903 bytes_retransmit=9 bytes_invalid=0 send_seq=74232 receive_seq=74232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999345 adj=63999476 Octopus_V1.1_F446: temp=33.6 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=34.1  heater_bed: target=55 temp=54.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452389 bytes_read=24634437 bytes_retransmit=9 bytes_invalid=0 send_seq=72777 receive_seq=72777 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999672 coil_temp=36.5 refs=0 mcu_temp=34.34 supply_voltage=3.014 sysload=0.14 cputime=3415.699 memavail=1404096 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=190.6 pwm=0.000
Stats 70923.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221543 bytes_read=8217833 bytes_retransmit=9 bytes_invalid=0 send_seq=90668 receive_seq=90668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999367 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=420984 bytes_read=1298201 bytes_retransmit=0 bytes_invalid=0 send_seq=70131 receive_seq=70131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013791 adj=50005064 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554864 bytes_read=7768006 bytes_retransmit=9 bytes_invalid=0 send_seq=74233 receive_seq=74233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999344 adj=63999497 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=35.9 raspberry_pi: temp=33.6  heater_bed: target=55 temp=54.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452395 bytes_read=24634793 bytes_retransmit=9 bytes_invalid=0 send_seq=72778 receive_seq=72778 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999704 coil_temp=36.5 refs=0 mcu_temp=34.21 supply_voltage=3.014 sysload=0.14 cputime=3415.757 memavail=1404092 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=188.5 pwm=0.000
Stats 70924.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221577 bytes_read=8217989 bytes_retransmit=9 bytes_invalid=0 send_seq=90671 receive_seq=90671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999365 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=420990 bytes_read=1298217 bytes_retransmit=0 bytes_invalid=0 send_seq=70132 receive_seq=70132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013614 adj=50004536 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554870 bytes_read=7768123 bytes_retransmit=9 bytes_invalid=0 send_seq=74234 receive_seq=74234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999343 adj=63999499 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=35.8 raspberry_pi: temp=33.6  heater_bed: target=55 temp=54.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452401 bytes_read=24635149 bytes_retransmit=9 bytes_invalid=0 send_seq=72779 receive_seq=72779 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999698 coil_temp=36.4 refs=0 mcu_temp=34.09 supply_voltage=3.014 sysload=0.13 cputime=3415.814 memavail=1402832 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=186.8 pwm=0.000
Stats 70925.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221611 bytes_read=8218116 bytes_retransmit=9 bytes_invalid=0 send_seq=90674 receive_seq=90674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999361 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=420996 bytes_read=1298233 bytes_retransmit=0 bytes_invalid=0 send_seq=70133 receive_seq=70133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013431 adj=50004034 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554876 bytes_read=7768241 bytes_retransmit=9 bytes_invalid=0 send_seq=74235 receive_seq=74235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999341 adj=63999507 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=35.0  heater_bed: target=55 temp=54.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452407 bytes_read=24635505 bytes_retransmit=9 bytes_invalid=0 send_seq=72780 receive_seq=72780 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999696 coil_temp=36.3 refs=0 mcu_temp=33.98 supply_voltage=3.014 sysload=0.13 cputime=3415.845 memavail=1402068 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=184.4 pwm=0.000
Stats 70926.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221645 bytes_read=8218243 bytes_retransmit=9 bytes_invalid=0 send_seq=90677 receive_seq=90677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999357 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=421002 bytes_read=1298249 bytes_retransmit=0 bytes_invalid=0 send_seq=70134 receive_seq=70134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013248 adj=50003535 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554882 bytes_read=7768354 bytes_retransmit=9 bytes_invalid=0 send_seq=74236 receive_seq=74236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999339 adj=63999510 Octopus_V1.1_F446: temp=33.5 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=34.6  heater_bed: target=55 temp=54.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452413 bytes_read=24635861 bytes_retransmit=9 bytes_invalid=0 send_seq=72781 receive_seq=72781 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999573 adj=31999708 coil_temp=36.3 refs=0 mcu_temp=33.87 supply_voltage=3.014 sysload=0.13 cputime=3415.868 memavail=1402068 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=182.7 pwm=0.000
Stats 70927.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000004 bytes_write=1221679 bytes_read=8218399 bytes_retransmit=9 bytes_invalid=0 send_seq=90680 receive_seq=90680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999354 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=421008 bytes_read=1298278 bytes_retransmit=0 bytes_invalid=0 send_seq=70135 receive_seq=70135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50013063 adj=50003101 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=554888 bytes_read=7768463 bytes_retransmit=9 bytes_invalid=0 send_seq=74237 receive_seq=74237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999336 adj=63999509 Octopus_V1.1_F446: temp=33.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=35.5  heater_bed: target=55 temp=54.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452419 bytes_read=24636217 bytes_retransmit=9 bytes_invalid=0 send_seq=72782 receive_seq=72782 retransmit_seq=12 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999721 coil_temp=36.2 refs=0 mcu_temp=33.70 supply_voltage=3.014 sysload=0.13 cputime=3415.892 memavail=1401844 print_time=70917.604 buffer_time=0.000 print_stall=0 extruder: target=220 temp=180.9 pwm=0.000
Attempting MCU 'mcu' reset command
Attempting MCU 'rpi' config_reset command
b'Got EOF when reading from device'
Attempting MCU 'toolboard_t0' reset command
Attempting MCU 'beacon' reset command
webhooks client 4123225008: Disconnected
Restarting printer
Start printer at Fri Sep 26 12:34:38 2025 (1758904478.6 70929.2)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	x1_step_pin=PF9,
	x1_dir_pin=PF10,
	x1_enable_pin=PG2,
	x1_uart_pin=PF2,
	x1_diag_pin=PG12,
	x1_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA0,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null

[mcu]
serial = /dev/RatOS/btt-octopus-11

[temperature_sensor Octopus_V1.1_F446]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_bus = spi3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD0,
	e_dir_pin=PD1,
	e_enable_pin=PD2,
	e_uart_pin=PA15,
	
	e_heater_pin=PB13,
	e_sensor_pin=PA3,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB12,
	bltouch_sensor_pin=PB8,
	bltouch_control_pin=PB9,
	probe_pin=PB9,
	fan_part_cooling_pin=PA0,
	fan_toolhead_cooling_pin=PA1,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-12-t0

[temperature_sensor EBB42_v1.2_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[adxl345 toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB12
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "back"
variable_start_print_park_z_height = 50
variable_end_print_park_in = "back"
variable_pause_print_park_in = "front"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = False
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.8, 59.8]
variable_bed_margin_y = [14.35, 30]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_true_zero_temp = 150
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = False
variable_beacon_scan_compensation_profile = "Contact"
variable_beacon_scan_compensation_probe_count = 15,15
variable_beacon_contact_poke_bottom_limit = -1
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_x_driver_types = ["tmc2209"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_y_axes = ["x1", "y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_homing %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	STOW_PROBE
	{% else %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_homing %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.configfile.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.configfile.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.configfile.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.configfile.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.configfile.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.configfile.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro _MOVE_TO_SAFE_Z_HOME]
description = Move to safe home position with optional Z_HOP (pass Z_HOP=True as parameter)
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	{% if params.Z_HOP is defined %}
	_Z_HOP
	{% endif %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, safe_home_x: {safe_home_x}, safe_home_y: {safe_home_y}, printable_x_max: {printable_x_max}, printable_y_max: {printable_y_max}"
	
	
	G0 X{safe_home_x} Y{safe_home_y} F{speed}

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis
variable_is_kinematic_position_overriden = False
gcode = 
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed, skipping.."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting presssure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_PARKING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_PARKING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined %}
	
	
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if act_t == toolhead %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% if printer.configfile.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE={default_profile} X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode}
	{% else %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD={default_profile}
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD={printer["gcode_macro RatOS"].bed_mesh_profile}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Recieved coordinates X0={x0} Y0={y0} X1={x1} Y1={y1}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% else %}
	
	{% set mesh_config = printer.configfile.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile}
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile}
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and printer.configfile.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.configfile.settings.beacon is defined and printer.configfile.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0} Y0={mesh_y0} X1={mesh_x1} Y1={mesh_y1}"
	{% if printer.configfile.settings.beacon is defined and beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE={default_profile} ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	BED_MESH_CALIBRATE PROFILE={default_profile} ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_APPLY_SCAN_COMPENSATION
	{% endif %}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	{% if printer["dual_carriage"] is defined %}
	
	_SET_TOOLHEAD_OFFSET T={printer["gcode_macro RatOS"].default_toolhead|int} MOVE=0
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0 MOVE=0
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% else %}
	M104.1 S{s} T{t}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for sensor: {sensor}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% endif %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for toolhead T{t} reached."

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_ORG
gcode = 
	SET_GCODE_OFFSET_ORG { rawparams }
	{% if printer.configfile.settings.beacon is defined and (params.Z_ADJUST is defined or params.Z is defined) %}
	_BEACON_APPLY_RUNTIME_MULTIPLIER
	{% endif %}

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.configfile.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.configfile.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.configfile.settings.bltouch is defined  %}
	{% set config_offset = printer.configfile.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.configfile.settings.probe is defined  %}
	{% set config_offset = printer.configfile.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.configfile.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.configfile.config.bed_mesh %}
	
	
	{% if printer.configfile.settings.bltouch is defined %}
	{% set x_offset = printer.configfile.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.configfile.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.configfile.settings.bltouch.z_offset|float %}
	{% elif printer.configfile.settings.probe is defined %}
	{% set x_offset = printer.configfile.settings.probe.x_offset|float %}
	{% set y_offset = printer.configfile.settings.probe.y_offset|float %}
	{% set z_offset = printer.configfile.settings.probe.z_offset|float %}
	{% elif printer.configfile.settings.beacon is defined %}
	{% set x_offset = printer.configfile.settings.beacon.x_offset|float %}
	{% set y_offset = printer.configfile.settings.beacon.y_offset|float %}
	{% set z_offset = printer.configfile.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.configfile.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.configfile.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.configfile.settings.bltouch is not defined and printer.configfile.settings.probe is not defined and printer.configfile.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.configfile.settings.bltouch is not defined and printer.configfile.settings.probe is not defined and printer.configfile.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET TOOLHEAD={current_toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F300 E{14 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead}
	{% endif %}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead}

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}"
	
	{% if not printer.virtual_sdcard.is_active %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull finished!" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	_LED_STANDBY
	CALCULATE_PRINTABLE_AREA
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	HELLO_RATOS

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
gcode = 
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.configfile.settings.ratos_hybrid_corexy is defined and printer.configfile.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.configfile.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro SAVE_Z_OFFSET]
gcode = 
	{% if printer.configfile.settings.beacon is defined %}
	_BEACON_SAVE_MULTIPLIER
	{% else %}
	Z_OFFSET_APPLY_PROBE
	{% endif %}

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.configfile.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING

[gcode_macro CANCEL_PRINT]
description = Cancels the printer
rename_existing = CANCEL_PRINT_BASE
gcode = 
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.configfile.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.configfile.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.configfile.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.configfile.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.configfile.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.configfile.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == '' %}
	_SET_TOOLHEAD_OFFSET T={default_toolhead} MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% set x_offset = printer.toolhead.position.x|float - printer.gcode_move.gcode_position.x|float %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	{% if idex_mode != '' %}
	
	{% set act_idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% if act_idex_mode == "copy" or act_idex_mode == "mirror" %}
	SET_GCODE_OFFSET X={x_offset} MOVE=0
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	{% if initial_tool != default_toolhead %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	SAVE_VARIABLE VARIABLE=idex_applied_offset VALUE={default_toolhead}
	
	_SET_TOOLHEAD_OFFSET T={initial_tool} MOVE=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	
	
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	_BEACON_SET_NOZZLE_TEMP_OFFSET TOOLHEAD={initial_tool}
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	{% if auto_z_offset_calibration %}
	{% set safe_distance = printer.configfile.settings.dual_carriage.safe_distance|float %}
	{% if default_toolhead == 0 %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	G1 X{safe_home_x - safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{safe_home_x + safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% elif default_toolhead == 1 %}
	_SELECT_TOOL T=1 TOOLSHIFT=false
	G1 X{safe_home_x + safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{safe_home_x - safe_distance / 2} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	{% endif %}
	{% else %}
	_MOVE_TO_SAFE_Z_HOME
	{% endif %}
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead}
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1}
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1
	BEACON_QUERY

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_true_zero_location = printer["gcode_macro RatOS"].beacon_contact_true_zero_location|default("front")|lower %}
	{% set beacon_contact_true_zero_margin_x = printer["gcode_macro RatOS"].beacon_contact_true_zero_margin_x|default(30)|int %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead}
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead}
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	{% if printer.configfile.settings.beacon is defined %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	SET_GCODE_OFFSET Z=0 MOVE=0
	{% endif %}
	{% endif %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	G91
	
	G1 E-2 F3600
	
	G0 Z{z_safe} F3600
	
	G1 E-{(r-2)} F3600
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS parameter for if you only want to do one axis at a time, (eg. GENERATE_SHAPER_GRAPHS AXIS=X)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=X FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_x
	
	{% elif axis == 'y' %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=Y FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_y
	
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	MAYBE_HOME
	TEST_RESONANCES AXIS=X FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	TEST_RESONANCES AXIS=Y FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_x
	RUN_SHELL_COMMAND CMD=generate_shaper_graph_y
	
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned.
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	MAYBE_HOME
	TEST_RESONANCES AXIS=1,1  OUTPUT=raw_data NAME=belt-tension-upper FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	TEST_RESONANCES AXIS=1,-1 OUTPUT=raw_data NAME=belt-tension-lower FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec}
	RUN_SHELL_COMMAND CMD=generate_belt_tension_graph
	
	
	
	_LED_INPUT_SHAPER_END
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_LEARN_MORE_CALIBRATION
	
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
allow_unsupported_slicer_versions = True
bypass_post_processing = True

[exclude_object]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.02
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114

[fan]
pin = !toolboard_t0:PA0
shutdown_speed = 1.0
cycle_time = 0.00004

[heater_fan toolhead_cooling_fan]
pin = toolboard_t0:PA1
fan_speed = 1
heater = extruder

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[delayed_gcode _HYBRID_INIT]
initial_duration = 0.1
gcode = 
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.configfile.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}

[stepper_x]
position_max = 559.8
position_endstop = -59.8
position_min = -59.8
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40
homing_speed = 50
endstop_pin = toolboard_t0:PB6

[stepper_y]
position_max = 530
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4
position_min = -5
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[bed_mesh]
horizontal_move_z = 2
mesh_min = 20,30
mesh_max = 470,450
probe_count = 40,40
fade_start = 1.0
fade_end = 10.0
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	30,30
	250,450
	470,30
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 4.63
full_steps_per_rotation = 200
filament_diameter = 1.750
max_extrude_only_velocity = 60
max_extrude_only_distance = 200
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB13
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA3
min_extrude_temp = 170
min_temp = 0
max_temp = 350
pressure_advance = 0.03
step_pin = toolboard_t0:PD0
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PD2
microsteps = 64
control = pid
pid_kp = 36.824
pid_ki = 12.275
pid_kd = 27.618

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.5

[resonance_tester]
accel_chip_x = adxl345 toolboard_t0
accel_chip_y = adxl345 toolboard_t0
probe_points = 
	250,250,20

[tmc2209 stepper_x]
stealthchop_threshold = 0
interpolate = False
uart_pin = PC4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_x1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PF2
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_x1]
step_pin = PF9
dir_pin = x1_dir_pin
enable_pin = !PG2
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40

[tmc2209 stepper_y]
stealthchop_threshold = 0
interpolate = False
uart_pin = PD11
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_y1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PC7
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA0
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 40

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = False
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = False
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = False
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 64
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PA15
run_current = 0.707
driver_tbl = 0
driver_toff = 4
driver_hend = 6
driver_hstrt = 7
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 22.5
mesh_main_direction = x
mesh_runs = 1
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	
	_BEACON_SET_NOZZLE_TEMP_OFFSET RESET=True
	
	
	{% set svv = printer.save_variables.variables %}
	{% set nozzle_expansion_coefficient_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(0)|float %}
	{% if nozzle_expansion_coefficient_multiplier == 0 %}
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is not defined %}
	{% set nozzle_expansion_coefficient_multiplier = 1.0 %}
	{% else %}
	{% set nozzle_expansion_coefficient_multiplier = printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier|default(1.0)|float %}
	{% endif %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier VALUE={nozzle_expansion_coefficient_multiplier}
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG={'"Please remove the variable beacon_contact_expansion_multiplier from your config file."'}
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_MEASURE_GANTRY_TWIST
	_BEACON_MAYBE_SCAN_COMPENSATION
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	G0 Z2 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.configfile.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set test_margin = 30 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
variable_runtime_temp = 0
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(0)|int %}
	{% set reset = true if params.RESET|default(false)|lower == 'true' else false %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if reset %}
	
	SAVE_VARIABLE VARIABLE=nozzle_expansion_applied_offset VALUE=0
	
	{% else %}
	{% if beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set nozzle_expansion_coefficient_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(1.0)|float %}
	
	
	{% set applied_offset = svv.nozzle_expansion_applied_offset|default(0)|float %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_offset = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = nozzle_expansion_coefficient_multiplier * (temp_offset * (expansion_coefficient / 100)) %}
	
	
	{% set new_offset = ((-applied_offset) + expansion_offset) %}
	SET_GCODE_OFFSET Z_ADJUST={new_offset} MOVE=1 SPEED={z_speed}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_applied_offset VALUE={expansion_offset}
	SET_GCODE_VARIABLE MACRO=_BEACON_SET_NOZZLE_TEMP_OFFSET VARIABLE=runtime_temp VALUE={temp}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="multiplier: {nozzle_expansion_coefficient_multiplier}, coefficient: {expansion_coefficient}, temp_offset: {temp_offset}, expansion_offset: {expansion_offset}, applied_offset: {applied_offset}, new_offset: {new_offset}"
	
	{% endif %}
	{% endif %}

[gcode_macro BEACON_MEASURE_GANTRY_TWIST]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x = printer["gcode_macro RatOS"].safe_home_x %}
	{% if safe_home_x is not defined or safe_home_x|lower == 'middle' %}
	{% set safe_home_x = printable_x_max / 2 %}
	{% endif %}
	{% set safe_home_y = printer["gcode_macro RatOS"].safe_home_y %}
	{% if safe_home_y is not defined or safe_home_y|lower == 'middle' %}
	{% set safe_home_y = printable_y_max / 2 %}
	{% endif %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure gantry twist..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_PROBE_GANTRY_TWIST
	_BEACON_STORE_GANTRY_TWIST LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_GANTRY_TWIST
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_PROBE_GANTRY_TWIST]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE
	BEACON_QUERY

[gcode_macro _BEACON_STORE_GANTRY_TWIST]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_GANTRY_TWIST]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low gantry twist: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low gantry twist: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High gantry twist: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High gantry twist: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high gantry twist: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_GANTRY_TWIST VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Gantry twist relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("Contact")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set probe_count = printer["gcode_macro RatOS"].beacon_scan_compensation_probe_count %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	{% endif %}
	
	
	{% if not automated %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES=2 SAMPLES_DROP=1 SAMPLES_TOLERANCE_RETRIES=10 PROBE_COUNT={probe_count[0]},{probe_count[1]} PROFILE={profile}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE={beacon_scan_compensation_profile}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_GANTRY_TWIST"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}

[gcode_macro _BEACON_SAVE_MULTIPLIER]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% set multiplier = printer["gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER"].runtime_multiplier|default(-1.0)|float %}
	
	DEBUG_ECHO PREFIX="_BEACON_SAVE_MULTIPLIER" MSG="multiplier: {multiplier}, beacon_contact_start_print_true_zero: {beacon_contact_start_print_true_zero}, beacon_contact_expansion_compensation: {beacon_contact_expansion_compensation}"
	
	{% if multiplier > 0 and beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier VALUE={multiplier}
	SET_GCODE_VARIABLE MACRO=_BEACON_APPLY_RUNTIME_MULTIPLIER VARIABLE=runtime_multiplier VALUE=-1.0
	CONSOLE_ECHO TITLE="Hotend thermal expansion compensation" TYPE="success" MSG={'"New value is: %.6f_N_The new multiplier value has been saved to the configuration."' % multiplier}
	{% else %}
	Z_OFFSET_APPLY_PROBE
	{% endif %}

[gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER]
variable_runtime_multiplier = -1.0
gcode = 
	
	{% set toolhead = 0 %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	{% if layer_number == 0 and is_printing_gcode %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Documentation" %}
	{% set line_1 = '"Your slicer is not correctly reporting layer information. See the layer change custom g-code in the <a href="%s" target="_blank" >%s</a>".' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Missing layer information" TYPE="warning" MSG={line_1}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_RUNTIME_MULTIPLIER" MSG="layer_number: {layer_number}, is_printing_gcode: {is_printing_gcode}, beacon_contact_start_print_true_zero: {beacon_contact_start_print_true_zero}, beacon_contact_expansion_compensation: {beacon_contact_expansion_compensation}"
	
	{% if layer_number == 1 and is_printing_gcode and printer.configfile.settings.beacon is defined and beacon_contact_start_print_true_zero and beacon_contact_expansion_compensation %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if toolhead == 1 %}
	{% set nozzle_expansion_coefficient = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set beacon_contact_expansion_multiplier = svv.nozzle_expansion_coefficient_multiplier|default(1.0)|float %}
	{% set print_temp = printer["gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET"].runtime_temp|default(0)|int %}
	
	{% if print_temp > 0 %}
	{% set z_offset = printer.gcode_move.homing_origin.z|float %}
	{% set temp_delta = print_temp - beacon_contact_true_zero_temp %}
	{% set coefficient_per_degree = nozzle_expansion_coefficient / 100 %}
	{% set z_offset_per_degree = z_offset / temp_delta %}
	{% set new_multiplier = z_offset_per_degree / coefficient_per_degree %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_RUNTIME_MULTIPLIER" MSG="print_temp: {print_temp}, z_offset: {z_offset}, temp_delta: {temp_delta}, nozzle_expansion_coefficient: {nozzle_expansion_coefficient}, coefficient_per_degree: {coefficient_per_degree}, z_offset_per_degree: {z_offset_per_degree}, old_multiplier: {beacon_contact_expansion_multiplier}, new_multiplier: {new_multiplier}"
	SET_GCODE_VARIABLE MACRO=_BEACON_APPLY_RUNTIME_MULTIPLIER VARIABLE=runtime_multiplier VALUE={new_multiplier}
	
	{% endif %}
	
	{% endif %}

[controller_fan controller_fan]
pin = PD12

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = False
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = False
variable_has_front_arm_nozzle_wiper = False
variable_resume_after_insert = False
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[filament_switch_sensor toolhead_filament_sensor_t0]
pause_on_runout = False
event_delay = 0.1
switch_pin = ^toolboard_t0:PB3
runout_gcode = 
	_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT TOOLHEAD=0
insert_gcode = 
	_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT TOOLHEAD=0

[gcode_button toolhead_filament_sensor_button_t0]
pin = ^!toolboard_t0:PB4
release_gcode = 
	_ON_FILAMENT_SENSOR_BUTTON_PRESSED TOOLHEAD=0
press_gcode = 

[output_pin caselight]
pin = PB11
pwm = True
cycle_time = 0.01
scale = 1.0
value = 1.0
shutdown_value = 0.0

[beacon model default]
model_coef = 1.5262425407123157,
	1.8789172227584032,
	0.847501001243572,
	0.4711280696377741,
	0.1746215419233843,
	-0.10944706696469403,
	-0.09554682575881597,
	0.15659764883575533,
	0.1469143147360675,
	0.005551915327827087
model_domain = 1.8559999301614767e-07,1.9376090302482318e-07
model_range = 0.200000,5.000000
model_temp = 51.224324
model_offset = 0.00000
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 4124998528: New connection
webhooks client 4124998528: Client info {'program': 'Moonraker', 'version': 'v0.9.3-116-gb11a791'}
Loaded MCU 'mcu' 144 commands (v0.13.0-272-g1be6c0fce / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_sdio=PC12,PD2,PC8,PC9,PC10,PC11 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1_PA6_PA7_PA5=PA6,PA7,PA5 BUS_PINS_spi1_PB4_PB5_PB3=PB4,PB5,PB3 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB14_PB15_PB13=PB14,PB15,PB13 BUS_PINS_spi2_PC2_PC3_PB10=PC2,PC3,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3_PB4_PB5_PB3=PB4,PB5,PB3 BUS_PINS_spi3_PC11_PC12_PC10=PC11,PC12,PC10 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 BUS_PINS_spi4_PE13_PE14_PE12=PE13,PE14,PE12 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=257 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_OPTIMIZED_EDGE=23 STEPPER_STEP_BOTH_EDGE=1
mcu 'rpi': Starting connect
Loaded MCU 'rpi' 119 commands (?-20240727_132503-fv-az659-741 / gcc: (Raspbian 10.2.1-6+rpi1) 10.2.1 20210110 binutils: (GNU Binutils for Raspbian) 2.35.2)
MCU 'rpi' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
mcu 'toolboard_t0': Starting serial connect
Loaded MCU 'toolboard_t0' 113 commands (v0.12.0-268-g0844388d / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu_temperature 'mcu' nominal base=-271.513944 slope=1305.179283
mcu_temperature 'toolboard_t0' nominal base=-261.242938 slope=1272.457627
mcu 'beacon': Starting serial connect
mcu 'beacon': Unable to open serial port: [Errno 2] could not open port /dev/beacon: [Errno 2] No such file or directory: '/dev/beacon'
Loaded MCU 'beacon' 45 commands (Beacon 2.1.0 / )
MCU 'beacon' config: ADC_MAX=4095 BEACON_ACCEL_BITS=12 BEACON_ACCEL_SCALE_16G=7.81 BEACON_ACCEL_SCALE_2G=0.98 BEACON_ACCEL_SCALE_4G=1.95 BEACON_ACCEL_SCALE_8G=3.91 BEACON_ADC_SMOOTH_COUNT=16 BEACON_HAS_ACCEL=1 BEACON_REV=H CLOCK_FREQ=32000000 MCU=beacon STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
Sending MCU 'rpi' printer configuration...
Configured MCU 'rpi' (1024 moves)
Sending MCU 'toolboard_t0' printer configuration...
Configured MCU 'toolboard_t0' (1024 moves)
Starting heater checks for heater_bed
bed_mesh: generated points
Index |  Tool Adjusted  |   Probe
  0   | (20.0, 7.5)     | (20.0, 30.0)
  1   | (31.5, 7.5)     | (31.5, 30.0)
  2   | (43.1, 7.5)     | (43.1, 30.0)
  3   | (54.6, 7.5)     | (54.6, 30.0)
  4   | (66.1, 7.5)     | (66.1, 30.0)
  5   | (77.7, 7.5)     | (77.7, 30.0)
  6   | (89.2, 7.5)     | (89.2, 30.0)
  7   | (100.7, 7.5)    | (100.7, 30.0)
  8   | (112.2, 7.5)    | (112.2, 30.0)
  9   | (123.8, 7.5)    | (123.8, 30.0)
  10  | (135.3, 7.5)    | (135.3, 30.0)
  11  | (146.8, 7.5)    | (146.8, 30.0)
  12  | (158.4, 7.5)    | (158.4, 30.0)
  13  | (169.9, 7.5)    | (169.9, 30.0)
  14  | (181.4, 7.5)    | (181.4, 30.0)
  15  | (192.9, 7.5)    | (192.9, 30.0)
  16  | (204.5, 7.5)    | (204.5, 30.0)
  17  | (216.0, 7.5)    | (216.0, 30.0)
  18  | (227.5, 7.5)    | (227.5, 30.0)
  19  | (239.1, 7.5)    | (239.1, 30.0)
  20  | (250.6, 7.5)    | (250.6, 30.0)
  21  | (262.1, 7.5)    | (262.1, 30.0)
  22  | (273.7, 7.5)    | (273.7, 30.0)
  23  | (285.2, 7.5)    | (285.2, 30.0)
  24  | (296.7, 7.5)    | (296.7, 30.0)
  25  | (308.2, 7.5)    | (308.2, 30.0)
  26  | (319.8, 7.5)    | (319.8, 30.0)
  27  | (331.3, 7.5)    | (331.3, 30.0)
  28  | (342.8, 7.5)    | (342.8, 30.0)
  29  | (354.4, 7.5)    | (354.4, 30.0)
  30  | (365.9, 7.5)    | (365.9, 30.0)
  31  | (377.4, 7.5)    | (377.4, 30.0)
  32  | (389.0, 7.5)    | (389.0, 30.0)
  33  | (400.5, 7.5)    | (400.5, 30.0)
  34  | (412.0, 7.5)    | (412.0, 30.0)
  35  | (423.5, 7.5)    | (423.5, 30.0)
  36  | (435.1, 7.5)    | (435.1, 30.0)
  37  | (446.6, 7.5)    | (446.6, 30.0)
  38  | (458.1, 7.5)    | (458.1, 30.0)
  39  | (469.7, 7.5)    | (469.7, 30.0)
  40  | (469.7, 18.3)   | (469.7, 40.8)
  41  | (458.1, 18.3)   | (458.1, 40.8)
  42  | (446.6, 18.3)   | (446.6, 40.8)
  43  | (435.1, 18.3)   | (435.1, 40.8)
  44  | (423.5, 18.3)   | (423.5, 40.8)
  45  | (412.0, 18.3)   | (412.0, 40.8)
  46  | (400.5, 18.3)   | (400.5, 40.8)
  47  | (389.0, 18.3)   | (389.0, 40.8)
  48  | (377.4, 18.3)   | (377.4, 40.8)
  49  | (365.9, 18.3)   | (365.9, 40.8)
  50  | (354.4, 18.3)   | (354.4, 40.8)
  51  | (342.8, 18.3)   | (342.8, 40.8)
  52  | (331.3, 18.3)   | (331.3, 40.8)
  53  | (319.8, 18.3)   | (319.8, 40.8)
  54  | (308.2, 18.3)   | (308.2, 40.8)
  55  | (296.7, 18.3)   | (296.7, 40.8)
  56  | (285.2, 18.3)   | (285.2, 40.8)
  57  | (273.7, 18.3)   | (273.7, 40.8)
  58  | (262.1, 18.3)   | (262.1, 40.8)
  59  | (250.6, 18.3)   | (250.6, 40.8)
  60  | (239.1, 18.3)   | (239.1, 40.8)
  61  | (227.5, 18.3)   | (227.5, 40.8)
  62  | (216.0, 18.3)   | (216.0, 40.8)
  63  | (204.5, 18.3)   | (204.5, 40.8)
  64  | (192.9, 18.3)   | (192.9, 40.8)
  65  | (181.4, 18.3)   | (181.4, 40.8)
  66  | (169.9, 18.3)   | (169.9, 40.8)
  67  | (158.4, 18.3)   | (158.4, 40.8)
  68  | (146.8, 18.3)   | (146.8, 40.8)
  69  | (135.3, 18.3)   | (135.3, 40.8)
  70  | (123.8, 18.3)   | (123.8, 40.8)
  71  | (112.2, 18.3)   | (112.2, 40.8)
  72  | (100.7, 18.3)   | (100.7, 40.8)
  73  | (89.2, 18.3)    | (89.2, 40.8)
  74  | (77.6, 18.3)    | (77.6, 40.8)
  75  | (66.1, 18.3)    | (66.1, 40.8)
  76  | (54.6, 18.3)    | (54.6, 40.8)
  77  | (43.1, 18.3)    | (43.1, 40.8)
  78  | (31.5, 18.3)    | (31.5, 40.8)
  79  | (20.0, 18.3)    | (20.0, 40.8)
  80  | (20.0, 29.0)    | (20.0, 51.5)
  81  | (31.5, 29.0)    | (31.5, 51.5)
  82  | (43.1, 29.0)    | (43.1, 51.5)
  83  | (54.6, 29.0)    | (54.6, 51.5)
  84  | (66.1, 29.0)    | (66.1, 51.5)
  85  | (77.7, 29.0)    | (77.7, 51.5)
  86  | (89.2, 29.0)    | (89.2, 51.5)
  87  | (100.7, 29.0)   | (100.7, 51.5)
  88  | (112.2, 29.0)   | (112.2, 51.5)
  89  | (123.8, 29.0)   | (123.8, 51.5)
  90  | (135.3, 29.0)   | (135.3, 51.5)
  91  | (146.8, 29.0)   | (146.8, 51.5)
  92  | (158.4, 29.0)   | (158.4, 51.5)
  93  | (169.9, 29.0)   | (169.9, 51.5)
  94  | (181.4, 29.0)   | (181.4, 51.5)
  95  | (192.9, 29.0)   | (192.9, 51.5)
  96  | (204.5, 29.0)   | (204.5, 51.5)
  97  | (216.0, 29.0)   | (216.0, 51.5)
  98  | (227.5, 29.0)   | (227.5, 51.5)
  99  | (239.1, 29.0)   | (239.1, 51.5)
  100 | (250.6, 29.0)   | (250.6, 51.5)
  101 | (262.1, 29.0)   | (262.1, 51.5)
  102 | (273.7, 29.0)   | (273.7, 51.5)
  103 | (285.2, 29.0)   | (285.2, 51.5)
  104 | (296.7, 29.0)   | (296.7, 51.5)
  105 | (308.2, 29.0)   | (308.2, 51.5)
  106 | (319.8, 29.0)   | (319.8, 51.5)
  107 | (331.3, 29.0)   | (331.3, 51.5)
  108 | (342.8, 29.0)   | (342.8, 51.5)
  109 | (354.4, 29.0)   | (354.4, 51.5)
  110 | (365.9, 29.0)   | (365.9, 51.5)
  111 | (377.4, 29.0)   | (377.4, 51.5)
  112 | (389.0, 29.0)   | (389.0, 51.5)
  113 | (400.5, 29.0)   | (400.5, 51.5)
  114 | (412.0, 29.0)   | (412.0, 51.5)
  115 | (423.5, 29.0)   | (423.5, 51.5)
  116 | (435.1, 29.0)   | (435.1, 51.5)
  117 | (446.6, 29.0)   | (446.6, 51.5)
  118 | (458.1, 29.0)   | (458.1, 51.5)
  119 | (469.7, 29.0)   | (469.7, 51.5)
  120 | (469.7, 39.8)   | (469.7, 62.3)
  121 | (458.1, 39.8)   | (458.1, 62.3)
  122 | (446.6, 39.8)   | (446.6, 62.3)
  123 | (435.1, 39.8)   | (435.1, 62.3)
  124 | (423.5, 39.8)   | (423.5, 62.3)
  125 | (412.0, 39.8)   | (412.0, 62.3)
  126 | (400.5, 39.8)   | (400.5, 62.3)
  127 | (389.0, 39.8)   | (389.0, 62.3)
  128 | (377.4, 39.8)   | (377.4, 62.3)
  129 | (365.9, 39.8)   | (365.9, 62.3)
  130 | (354.4, 39.8)   | (354.4, 62.3)
  131 | (342.8, 39.8)   | (342.8, 62.3)
  132 | (331.3, 39.8)   | (331.3, 62.3)
  133 | (319.8, 39.8)   | (319.8, 62.3)
  134 | (308.2, 39.8)   | (308.2, 62.3)
  135 | (296.7, 39.8)   | (296.7, 62.3)
  136 | (285.2, 39.8)   | (285.2, 62.3)
  137 | (273.7, 39.8)   | (273.7, 62.3)
  138 | (262.1, 39.8)   | (262.1, 62.3)
  139 | (250.6, 39.8)   | (250.6, 62.3)
  140 | (239.1, 39.8)   | (239.1, 62.3)
  141 | (227.5, 39.8)   | (227.5, 62.3)
  142 | (216.0, 39.8)   | (216.0, 62.3)
  143 | (204.5, 39.8)   | (204.5, 62.3)
  144 | (192.9, 39.8)   | (192.9, 62.3)
  145 | (181.4, 39.8)   | (181.4, 62.3)
  146 | (169.9, 39.8)   | (169.9, 62.3)
  147 | (158.4, 39.8)   | (158.4, 62.3)
  148 | (146.8, 39.8)   | (146.8, 62.3)
  149 | (135.3, 39.8)   | (135.3, 62.3)
  150 | (123.8, 39.8)   | (123.8, 62.3)
  151 | (112.2, 39.8)   | (112.2, 62.3)
  152 | (100.7, 39.8)   | (100.7, 62.3)
  153 | (89.2, 39.8)    | (89.2, 62.3)
  154 | (77.6, 39.8)    | (77.6, 62.3)
  155 | (66.1, 39.8)    | (66.1, 62.3)
  156 | (54.6, 39.8)    | (54.6, 62.3)
  157 | (43.1, 39.8)    | (43.1, 62.3)
  158 | (31.5, 39.8)    | (31.5, 62.3)
  159 | (20.0, 39.8)    | (20.0, 62.3)
  160 | (20.0, 50.5)    | (20.0, 73.0)
  161 | (31.5, 50.5)    | (31.5, 73.0)
  162 | (43.1, 50.5)    | (43.1, 73.0)
  163 | (54.6, 50.5)    | (54.6, 73.0)
  164 | (66.1, 50.5)    | (66.1, 73.0)
  165 | (77.7, 50.5)    | (77.7, 73.0)
  166 | (89.2, 50.5)    | (89.2, 73.0)
  167 | (100.7, 50.5)   | (100.7, 73.0)
  168 | (112.2, 50.5)   | (112.2, 73.0)
  169 | (123.8, 50.5)   | (123.8, 73.0)
  170 | (135.3, 50.5)   | (135.3, 73.0)
  171 | (146.8, 50.5)   | (146.8, 73.0)
  172 | (158.4, 50.5)   | (158.4, 73.0)
  173 | (169.9, 50.5)   | (169.9, 73.0)
  174 | (181.4, 50.5)   | (181.4, 73.0)
  175 | (192.9, 50.5)   | (192.9, 73.0)
  176 | (204.5, 50.5)   | (204.5, 73.0)
  177 | (216.0, 50.5)   | (216.0, 73.0)
  178 | (227.5, 50.5)   | (227.5, 73.0)
  179 | (239.1, 50.5)   | (239.1, 73.0)
  180 | (250.6, 50.5)   | (250.6, 73.0)
  181 | (262.1, 50.5)   | (262.1, 73.0)
  182 | (273.7, 50.5)   | (273.7, 73.0)
  183 | (285.2, 50.5)   | (285.2, 73.0)
  184 | (296.7, 50.5)   | (296.7, 73.0)
  185 | (308.2, 50.5)   | (308.2, 73.0)
  186 | (319.8, 50.5)   | (319.8, 73.0)
  187 | (331.3, 50.5)   | (331.3, 73.0)
  188 | (342.8, 50.5)   | (342.8, 73.0)
  189 | (354.4, 50.5)   | (354.4, 73.0)
  190 | (365.9, 50.5)   | (365.9, 73.0)
  191 | (377.4, 50.5)   | (377.4, 73.0)
  192 | (389.0, 50.5)   | (389.0, 73.0)
  193 | (400.5, 50.5)   | (400.5, 73.0)
  194 | (412.0, 50.5)   | (412.0, 73.0)
  195 | (423.5, 50.5)   | (423.5, 73.0)
  196 | (435.1, 50.5)   | (435.1, 73.0)
  197 | (446.6, 50.5)   | (446.6, 73.0)
  198 | (458.1, 50.5)   | (458.1, 73.0)
  199 | (469.7, 50.5)   | (469.7, 73.0)
  200 | (469.7, 61.3)   | (469.7, 83.8)
  201 | (458.1, 61.3)   | (458.1, 83.8)
  202 | (446.6, 61.3)   | (446.6, 83.8)
  203 | (435.1, 61.3)   | (435.1, 83.8)
  204 | (423.5, 61.3)   | (423.5, 83.8)
  205 | (412.0, 61.3)   | (412.0, 83.8)
  206 | (400.5, 61.3)   | (400.5, 83.8)
  207 | (389.0, 61.3)   | (389.0, 83.8)
  208 | (377.4, 61.3)   | (377.4, 83.8)
  209 | (365.9, 61.3)   | (365.9, 83.8)
  210 | (354.4, 61.3)   | (354.4, 83.8)
  211 | (342.8, 61.3)   | (342.8, 83.8)
  212 | (331.3, 61.3)   | (331.3, 83.8)
  213 | (319.8, 61.3)   | (319.8, 83.8)
  214 | (308.2, 61.3)   | (308.2, 83.8)
  215 | (296.7, 61.3)   | (296.7, 83.8)
  216 | (285.2, 61.3)   | (285.2, 83.8)
  217 | (273.7, 61.3)   | (273.7, 83.8)
  218 | (262.1, 61.3)   | (262.1, 83.8)
  219 | (250.6, 61.3)   | (250.6, 83.8)
  220 | (239.1, 61.3)   | (239.1, 83.8)
  221 | (227.5, 61.3)   | (227.5, 83.8)
  222 | (216.0, 61.3)   | (216.0, 83.8)
  223 | (204.5, 61.3)   | (204.5, 83.8)
  224 | (192.9, 61.3)   | (192.9, 83.8)
  225 | (181.4, 61.3)   | (181.4, 83.8)
  226 | (169.9, 61.3)   | (169.9, 83.8)
  227 | (158.4, 61.3)   | (158.4, 83.8)
  228 | (146.8, 61.3)   | (146.8, 83.8)
  229 | (135.3, 61.3)   | (135.3, 83.8)
  230 | (123.8, 61.3)   | (123.8, 83.8)
  231 | (112.2, 61.3)   | (112.2, 83.8)
  232 | (100.7, 61.3)   | (100.7, 83.8)
  233 | (89.2, 61.3)    | (89.2, 83.8)
  234 | (77.6, 61.3)    | (77.6, 83.8)
  235 | (66.1, 61.3)    | (66.1, 83.8)
  236 | (54.6, 61.3)    | (54.6, 83.8)
  237 | (43.1, 61.3)    | (43.1, 83.8)
  238 | (31.5, 61.3)    | (31.5, 83.8)
  239 | (20.0, 61.3)    | (20.0, 83.8)
  240 | (20.0, 72.1)    | (20.0, 94.6)
  241 | (31.5, 72.1)    | (31.5, 94.6)
  242 | (43.1, 72.1)    | (43.1, 94.6)
  243 | (54.6, 72.1)    | (54.6, 94.6)
  244 | (66.1, 72.1)    | (66.1, 94.6)
  245 | (77.7, 72.1)    | (77.7, 94.6)
  246 | (89.2, 72.1)    | (89.2, 94.6)
  247 | (100.7, 72.1)   | (100.7, 94.6)
  248 | (112.2, 72.1)   | (112.2, 94.6)
  249 | (123.8, 72.1)   | (123.8, 94.6)
  250 | (135.3, 72.1)   | (135.3, 94.6)
  251 | (146.8, 72.1)   | (146.8, 94.6)
  252 | (158.4, 72.1)   | (158.4, 94.6)
  253 | (169.9, 72.1)   | (169.9, 94.6)
  254 | (181.4, 72.1)   | (181.4, 94.6)
  255 | (192.9, 72.1)   | (192.9, 94.6)
  256 | (204.5, 72.1)   | (204.5, 94.6)
  257 | (216.0, 72.1)   | (216.0, 94.6)
  258 | (227.5, 72.1)   | (227.5, 94.6)
  259 | (239.1, 72.1)   | (239.1, 94.6)
  260 | (250.6, 72.1)   | (250.6, 94.6)
  261 | (262.1, 72.1)   | (262.1, 94.6)
  262 | (273.7, 72.1)   | (273.7, 94.6)
  263 | (285.2, 72.1)   | (285.2, 94.6)
  264 | (296.7, 72.1)   | (296.7, 94.6)
  265 | (308.2, 72.1)   | (308.2, 94.6)
  266 | (319.8, 72.1)   | (319.8, 94.6)
  267 | (331.3, 72.1)   | (331.3, 94.6)
  268 | (342.8, 72.1)   | (342.8, 94.6)
  269 | (354.4, 72.1)   | (354.4, 94.6)
  270 | (365.9, 72.1)   | (365.9, 94.6)
  271 | (377.4, 72.1)   | (377.4, 94.6)
  272 | (389.0, 72.1)   | (389.0, 94.6)
  273 | (400.5, 72.1)   | (400.5, 94.6)
  274 | (412.0, 72.1)   | (412.0, 94.6)
  275 | (423.5, 72.1)   | (423.5, 94.6)
  276 | (435.1, 72.1)   | (435.1, 94.6)
  277 | (446.6, 72.1)   | (446.6, 94.6)
  278 | (458.1, 72.1)   | (458.1, 94.6)
  279 | (469.7, 72.1)   | (469.7, 94.6)
  280 | (469.7, 82.8)   | (469.7, 105.3)
  281 | (458.1, 82.8)   | (458.1, 105.3)
  282 | (446.6, 82.8)   | (446.6, 105.3)
  283 | (435.1, 82.8)   | (435.1, 105.3)
  284 | (423.5, 82.8)   | (423.5, 105.3)
  285 | (412.0, 82.8)   | (412.0, 105.3)
  286 | (400.5, 82.8)   | (400.5, 105.3)
  287 | (389.0, 82.8)   | (389.0, 105.3)
  288 | (377.4, 82.8)   | (377.4, 105.3)
  289 | (365.9, 82.8)   | (365.9, 105.3)
  290 | (354.4, 82.8)   | (354.4, 105.3)
  291 | (342.8, 82.8)   | (342.8, 105.3)
  292 | (331.3, 82.8)   | (331.3, 105.3)
  293 | (319.8, 82.8)   | (319.8, 105.3)
  294 | (308.2, 82.8)   | (308.2, 105.3)
  295 | (296.7, 82.8)   | (296.7, 105.3)
  296 | (285.2, 82.8)   | (285.2, 105.3)
  297 | (273.7, 82.8)   | (273.7, 105.3)
  298 | (262.1, 82.8)   | (262.1, 105.3)
  299 | (250.6, 82.8)   | (250.6, 105.3)
  300 | (239.1, 82.8)   | (239.1, 105.3)
  301 | (227.5, 82.8)   | (227.5, 105.3)
  302 | (216.0, 82.8)   | (216.0, 105.3)
  303 | (204.5, 82.8)   | (204.5, 105.3)
  304 | (192.9, 82.8)   | (192.9, 105.3)
  305 | (181.4, 82.8)   | (181.4, 105.3)
  306 | (169.9, 82.8)   | (169.9, 105.3)
  307 | (158.4, 82.8)   | (158.4, 105.3)
  308 | (146.8, 82.8)   | (146.8, 105.3)
  309 | (135.3, 82.8)   | (135.3, 105.3)
  310 | (123.8, 82.8)   | (123.8, 105.3)
  311 | (112.2, 82.8)   | (112.2, 105.3)
  312 | (100.7, 82.8)   | (100.7, 105.3)
  313 | (89.2, 82.8)    | (89.2, 105.3)
  314 | (77.6, 82.8)    | (77.6, 105.3)
  315 | (66.1, 82.8)    | (66.1, 105.3)
  316 | (54.6, 82.8)    | (54.6, 105.3)
  317 | (43.1, 82.8)    | (43.1, 105.3)
  318 | (31.5, 82.8)    | (31.5, 105.3)
  319 | (20.0, 82.8)    | (20.0, 105.3)
  320 | (20.0, 93.6)    | (20.0, 116.1)
  321 | (31.5, 93.6)    | (31.5, 116.1)
  322 | (43.1, 93.6)    | (43.1, 116.1)
  323 | (54.6, 93.6)    | (54.6, 116.1)
  324 | (66.1, 93.6)    | (66.1, 116.1)
  325 | (77.7, 93.6)    | (77.7, 116.1)
  326 | (89.2, 93.6)    | (89.2, 116.1)
  327 | (100.7, 93.6)   | (100.7, 116.1)
  328 | (112.2, 93.6)   | (112.2, 116.1)
  329 | (123.8, 93.6)   | (123.8, 116.1)
  330 | (135.3, 93.6)   | (135.3, 116.1)
  331 | (146.8, 93.6)   | (146.8, 116.1)
  332 | (158.4, 93.6)   | (158.4, 116.1)
  333 | (169.9, 93.6)   | (169.9, 116.1)
  334 | (181.4, 93.6)   | (181.4, 116.1)
  335 | (192.9, 93.6)   | (192.9, 116.1)
  336 | (204.5, 93.6)   | (204.5, 116.1)
  337 | (216.0, 93.6)   | (216.0, 116.1)
  338 | (227.5, 93.6)   | (227.5, 116.1)
  339 | (239.1, 93.6)   | (239.1, 116.1)
  340 | (250.6, 93.6)   | (250.6, 116.1)
  341 | (262.1, 93.6)   | (262.1, 116.1)
  342 | (273.7, 93.6)   | (273.7, 116.1)
  343 | (285.2, 93.6)   | (285.2, 116.1)
  344 | (296.7, 93.6)   | (296.7, 116.1)
  345 | (308.2, 93.6)   | (308.2, 116.1)
  346 | (319.8, 93.6)   | (319.8, 116.1)
  347 | (331.3, 93.6)   | (331.3, 116.1)
  348 | (342.8, 93.6)   | (342.8, 116.1)
  349 | (354.4, 93.6)   | (354.4, 116.1)
  350 | (365.9, 93.6)   | (365.9, 116.1)
  351 | (377.4, 93.6)   | (377.4, 116.1)
  352 | (389.0, 93.6)   | (389.0, 116.1)
  353 | (400.5, 93.6)   | (400.5, 116.1)
  354 | (412.0, 93.6)   | (412.0, 116.1)
  355 | (423.5, 93.6)   | (423.5, 116.1)
  356 | (435.1, 93.6)   | (435.1, 116.1)
  357 | (446.6, 93.6)   | (446.6, 116.1)
  358 | (458.1, 93.6)   | (458.1, 116.1)
  359 | (469.7, 93.6)   | (469.7, 116.1)
  360 | (469.7, 104.3)  | (469.7, 126.8)
  361 | (458.1, 104.3)  | (458.1, 126.8)
  362 | (446.6, 104.3)  | (446.6, 126.8)
  363 | (435.1, 104.3)  | (435.1, 126.8)
  364 | (423.5, 104.3)  | (423.5, 126.8)
  365 | (412.0, 104.3)  | (412.0, 126.8)
  366 | (400.5, 104.3)  | (400.5, 126.8)
  367 | (389.0, 104.3)  | (389.0, 126.8)
  368 | (377.4, 104.3)  | (377.4, 126.8)
  369 | (365.9, 104.3)  | (365.9, 126.8)
  370 | (354.4, 104.3)  | (354.4, 126.8)
  371 | (342.8, 104.3)  | (342.8, 126.8)
  372 | (331.3, 104.3)  | (331.3, 126.8)
  373 | (319.8, 104.3)  | (319.8, 126.8)
  374 | (308.2, 104.3)  | (308.2, 126.8)
  375 | (296.7, 104.3)  | (296.7, 126.8)
  376 | (285.2, 104.3)  | (285.2, 126.8)
  377 | (273.7, 104.3)  | (273.7, 126.8)
  378 | (262.1, 104.3)  | (262.1, 126.8)
  379 | (250.6, 104.3)  | (250.6, 126.8)
  380 | (239.1, 104.3)  | (239.1, 126.8)
  381 | (227.5, 104.3)  | (227.5, 126.8)
  382 | (216.0, 104.3)  | (216.0, 126.8)
  383 | (204.5, 104.3)  | (204.5, 126.8)
  384 | (192.9, 104.3)  | (192.9, 126.8)
  385 | (181.4, 104.3)  | (181.4, 126.8)
  386 | (169.9, 104.3)  | (169.9, 126.8)
  387 | (158.4, 104.3)  | (158.4, 126.8)
  388 | (146.8, 104.3)  | (146.8, 126.8)
  389 | (135.3, 104.3)  | (135.3, 126.8)
  390 | (123.8, 104.3)  | (123.8, 126.8)
  391 | (112.2, 104.3)  | (112.2, 126.8)
  392 | (100.7, 104.3)  | (100.7, 126.8)
  393 | (89.2, 104.3)   | (89.2, 126.8)
  394 | (77.6, 104.3)   | (77.6, 126.8)
  395 | (66.1, 104.3)   | (66.1, 126.8)
  396 | (54.6, 104.3)   | (54.6, 126.8)
  397 | (43.1, 104.3)   | (43.1, 126.8)
  398 | (31.5, 104.3)   | (31.5, 126.8)
  399 | (20.0, 104.3)   | (20.0, 126.8)
  400 | (20.0, 115.1)   | (20.0, 137.6)
  401 | (31.5, 115.1)   | (31.5, 137.6)
  402 | (43.1, 115.1)   | (43.1, 137.6)
  403 | (54.6, 115.1)   | (54.6, 137.6)
  404 | (66.1, 115.1)   | (66.1, 137.6)
  405 | (77.7, 115.1)   | (77.7, 137.6)
  406 | (89.2, 115.1)   | (89.2, 137.6)
  407 | (100.7, 115.1)  | (100.7, 137.6)
  408 | (112.2, 115.1)  | (112.2, 137.6)
  409 | (123.8, 115.1)  | (123.8, 137.6)
  410 | (135.3, 115.1)  | (135.3, 137.6)
  411 | (146.8, 115.1)  | (146.8, 137.6)
  412 | (158.4, 115.1)  | (158.4, 137.6)
  413 | (169.9, 115.1)  | (169.9, 137.6)
  414 | (181.4, 115.1)  | (181.4, 137.6)
  415 | (192.9, 115.1)  | (192.9, 137.6)
  416 | (204.5, 115.1)  | (204.5, 137.6)
  417 | (216.0, 115.1)  | (216.0, 137.6)
  418 | (227.5, 115.1)  | (227.5, 137.6)
  419 | (239.1, 115.1)  | (239.1, 137.6)
  420 | (250.6, 115.1)  | (250.6, 137.6)
  421 | (262.1, 115.1)  | (262.1, 137.6)
  422 | (273.7, 115.1)  | (273.7, 137.6)
  423 | (285.2, 115.1)  | (285.2, 137.6)
  424 | (296.7, 115.1)  | (296.7, 137.6)
  425 | (308.2, 115.1)  | (308.2, 137.6)
  426 | (319.8, 115.1)  | (319.8, 137.6)
  427 | (331.3, 115.1)  | (331.3, 137.6)
  428 | (342.8, 115.1)  | (342.8, 137.6)
  429 | (354.4, 115.1)  | (354.4, 137.6)
  430 | (365.9, 115.1)  | (365.9, 137.6)
  431 | (377.4, 115.1)  | (377.4, 137.6)
  432 | (389.0, 115.1)  | (389.0, 137.6)
  433 | (400.5, 115.1)  | (400.5, 137.6)
  434 | (412.0, 115.1)  | (412.0, 137.6)
  435 | (423.5, 115.1)  | (423.5, 137.6)
  436 | (435.1, 115.1)  | (435.1, 137.6)
  437 | (446.6, 115.1)  | (446.6, 137.6)
  438 | (458.1, 115.1)  | (458.1, 137.6)
  439 | (469.7, 115.1)  | (469.7, 137.6)
  440 | (469.7, 125.9)  | (469.7, 148.4)
  441 | (458.1, 125.9)  | (458.1, 148.4)
  442 | (446.6, 125.9)  | (446.6, 148.4)
  443 | (435.1, 125.9)  | (435.1, 148.4)
  444 | (423.5, 125.9)  | (423.5, 148.4)
  445 | (412.0, 125.9)  | (412.0, 148.4)
  446 | (400.5, 125.9)  | (400.5, 148.4)
  447 | (389.0, 125.9)  | (389.0, 148.4)
  448 | (377.4, 125.9)  | (377.4, 148.4)
  449 | (365.9, 125.9)  | (365.9, 148.4)
  450 | (354.4, 125.9)  | (354.4, 148.4)
  451 | (342.8, 125.9)  | (342.8, 148.4)
  452 | (331.3, 125.9)  | (331.3, 148.4)
  453 | (319.8, 125.9)  | (319.8, 148.4)
  454 | (308.2, 125.9)  | (308.2, 148.4)
  455 | (296.7, 125.9)  | (296.7, 148.4)
  456 | (285.2, 125.9)  | (285.2, 148.4)
  457 | (273.7, 125.9)  | (273.7, 148.4)
  458 | (262.1, 125.9)  | (262.1, 148.4)
  459 | (250.6, 125.9)  | (250.6, 148.4)
  460 | (239.1, 125.9)  | (239.1, 148.4)
  461 | (227.5, 125.9)  | (227.5, 148.4)
  462 | (216.0, 125.9)  | (216.0, 148.4)
  463 | (204.5, 125.9)  | (204.5, 148.4)
  464 | (192.9, 125.9)  | (192.9, 148.4)
  465 | (181.4, 125.9)  | (181.4, 148.4)
  466 | (169.9, 125.9)  | (169.9, 148.4)
  467 | (158.4, 125.9)  | (158.4, 148.4)
  468 | (146.8, 125.9)  | (146.8, 148.4)
  469 | (135.3, 125.9)  | (135.3, 148.4)
  470 | (123.8, 125.9)  | (123.8, 148.4)
  471 | (112.2, 125.9)  | (112.2, 148.4)
  472 | (100.7, 125.9)  | (100.7, 148.4)
  473 | (89.2, 125.9)   | (89.2, 148.4)
  474 | (77.6, 125.9)   | (77.6, 148.4)
  475 | (66.1, 125.9)   | (66.1, 148.4)
  476 | (54.6, 125.9)   | (54.6, 148.4)
  477 | (43.1, 125.9)   | (43.1, 148.4)
  478 | (31.5, 125.9)   | (31.5, 148.4)
  479 | (20.0, 125.9)   | (20.0, 148.4)
  480 | (20.0, 136.6)   | (20.0, 159.1)
  481 | (31.5, 136.6)   | (31.5, 159.1)
  482 | (43.1, 136.6)   | (43.1, 159.1)
  483 | (54.6, 136.6)   | (54.6, 159.1)
  484 | (66.1, 136.6)   | (66.1, 159.1)
  485 | (77.7, 136.6)   | (77.7, 159.1)
  486 | (89.2, 136.6)   | (89.2, 159.1)
  487 | (100.7, 136.6)  | (100.7, 159.1)
  488 | (112.2, 136.6)  | (112.2, 159.1)
  489 | (123.8, 136.6)  | (123.8, 159.1)
  490 | (135.3, 136.6)  | (135.3, 159.1)
  491 | (146.8, 136.6)  | (146.8, 159.1)
  492 | (158.4, 136.6)  | (158.4, 159.1)
  493 | (169.9, 136.6)  | (169.9, 159.1)
  494 | (181.4, 136.6)  | (181.4, 159.1)
  495 | (192.9, 136.6)  | (192.9, 159.1)
  496 | (204.5, 136.6)  | (204.5, 159.1)
  497 | (216.0, 136.6)  | (216.0, 159.1)
  498 | (227.5, 136.6)  | (227.5, 159.1)
  499 | (239.1, 136.6)  | (239.1, 159.1)
  500 | (250.6, 136.6)  | (250.6, 159.1)
  501 | (262.1, 136.6)  | (262.1, 159.1)
  502 | (273.7, 136.6)  | (273.7, 159.1)
  503 | (285.2, 136.6)  | (285.2, 159.1)
  504 | (296.7, 136.6)  | (296.7, 159.1)
  505 | (308.2, 136.6)  | (308.2, 159.1)
  506 | (319.8, 136.6)  | (319.8, 159.1)
  507 | (331.3, 136.6)  | (331.3, 159.1)
  508 | (342.8, 136.6)  | (342.8, 159.1)
  509 | (354.4, 136.6)  | (354.4, 159.1)
  510 | (365.9, 136.6)  | (365.9, 159.1)
  511 | (377.4, 136.6)  | (377.4, 159.1)
  512 | (389.0, 136.6)  | (389.0, 159.1)
  513 | (400.5, 136.6)  | (400.5, 159.1)
  514 | (412.0, 136.6)  | (412.0, 159.1)
  515 | (423.5, 136.6)  | (423.5, 159.1)
  516 | (435.1, 136.6)  | (435.1, 159.1)
  517 | (446.6, 136.6)  | (446.6, 159.1)
  518 | (458.1, 136.6)  | (458.1, 159.1)
  519 | (469.7, 136.6)  | (469.7, 159.1)
  520 | (469.7, 147.4)  | (469.7, 169.9)
  521 | (458.1, 147.4)  | (458.1, 169.9)
  522 | (446.6, 147.4)  | (446.6, 169.9)
  523 | (435.1, 147.4)  | (435.1, 169.9)
  524 | (423.5, 147.4)  | (423.5, 169.9)
  525 | (412.0, 147.4)  | (412.0, 169.9)
  526 | (400.5, 147.4)  | (400.5, 169.9)
  527 | (389.0, 147.4)  | (389.0, 169.9)
  528 | (377.4, 147.4)  | (377.4, 169.9)
  529 | (365.9, 147.4)  | (365.9, 169.9)
  530 | (354.4, 147.4)  | (354.4, 169.9)
  531 | (342.8, 147.4)  | (342.8, 169.9)
  532 | (331.3, 147.4)  | (331.3, 169.9)
  533 | (319.8, 147.4)  | (319.8, 169.9)
  534 | (308.2, 147.4)  | (308.2, 169.9)
  535 | (296.7, 147.4)  | (296.7, 169.9)
  536 | (285.2, 147.4)  | (285.2, 169.9)
  537 | (273.7, 147.4)  | (273.7, 169.9)
  538 | (262.1, 147.4)  | (262.1, 169.9)
  539 | (250.6, 147.4)  | (250.6, 169.9)
  540 | (239.1, 147.4)  | (239.1, 169.9)
  541 | (227.5, 147.4)  | (227.5, 169.9)
  542 | (216.0, 147.4)  | (216.0, 169.9)
  543 | (204.5, 147.4)  | (204.5, 169.9)
  544 | (192.9, 147.4)  | (192.9, 169.9)
  545 | (181.4, 147.4)  | (181.4, 169.9)
  546 | (169.9, 147.4)  | (169.9, 169.9)
  547 | (158.4, 147.4)  | (158.4, 169.9)
  548 | (146.8, 147.4)  | (146.8, 169.9)
  549 | (135.3, 147.4)  | (135.3, 169.9)
  550 | (123.8, 147.4)  | (123.8, 169.9)
  551 | (112.2, 147.4)  | (112.2, 169.9)
  552 | (100.7, 147.4)  | (100.7, 169.9)
  553 | (89.2, 147.4)   | (89.2, 169.9)
  554 | (77.6, 147.4)   | (77.6, 169.9)
  555 | (66.1, 147.4)   | (66.1, 169.9)
  556 | (54.6, 147.4)   | (54.6, 169.9)
  557 | (43.1, 147.4)   | (43.1, 169.9)
  558 | (31.5, 147.4)   | (31.5, 169.9)
  559 | (20.0, 147.4)   | (20.0, 169.9)
  560 | (20.0, 158.1)   | (20.0, 180.6)
  561 | (31.5, 158.1)   | (31.5, 180.6)
  562 | (43.1, 158.1)   | (43.1, 180.6)
  563 | (54.6, 158.1)   | (54.6, 180.6)
  564 | (66.1, 158.1)   | (66.1, 180.6)
  565 | (77.7, 158.1)   | (77.7, 180.6)
  566 | (89.2, 158.1)   | (89.2, 180.6)
  567 | (100.7, 158.1)  | (100.7, 180.6)
  568 | (112.2, 158.1)  | (112.2, 180.6)
  569 | (123.8, 158.1)  | (123.8, 180.6)
  570 | (135.3, 158.1)  | (135.3, 180.6)
  571 | (146.8, 158.1)  | (146.8, 180.6)
  572 | (158.4, 158.1)  | (158.4, 180.6)
  573 | (169.9, 158.1)  | (169.9, 180.6)
  574 | (181.4, 158.1)  | (181.4, 180.6)
  575 | (192.9, 158.1)  | (192.9, 180.6)
  576 | (204.5, 158.1)  | (204.5, 180.6)
  577 | (216.0, 158.1)  | (216.0, 180.6)
  578 | (227.5, 158.1)  | (227.5, 180.6)
  579 | (239.1, 158.1)  | (239.1, 180.6)
  580 | (250.6, 158.1)  | (250.6, 180.6)
  581 | (262.1, 158.1)  | (262.1, 180.6)
  582 | (273.7, 158.1)  | (273.7, 180.6)
  583 | (285.2, 158.1)  | (285.2, 180.6)
  584 | (296.7, 158.1)  | (296.7, 180.6)
  585 | (308.2, 158.1)  | (308.2, 180.6)
  586 | (319.8, 158.1)  | (319.8, 180.6)
  587 | (331.3, 158.1)  | (331.3, 180.6)
  588 | (342.8, 158.1)  | (342.8, 180.6)
  589 | (354.4, 158.1)  | (354.4, 180.6)
  590 | (365.9, 158.1)  | (365.9, 180.6)
  591 | (377.4, 158.1)  | (377.4, 180.6)
  592 | (389.0, 158.1)  | (389.0, 180.6)
  593 | (400.5, 158.1)  | (400.5, 180.6)
  594 | (412.0, 158.1)  | (412.0, 180.6)
  595 | (423.5, 158.1)  | (423.5, 180.6)
  596 | (435.1, 158.1)  | (435.1, 180.6)
  597 | (446.6, 158.1)  | (446.6, 180.6)
  598 | (458.1, 158.1)  | (458.1, 180.6)
  599 | (469.7, 158.1)  | (469.7, 180.6)
  600 | (469.7, 168.9)  | (469.7, 191.4)
  601 | (458.1, 168.9)  | (458.1, 191.4)
  602 | (446.6, 168.9)  | (446.6, 191.4)
  603 | (435.1, 168.9)  | (435.1, 191.4)
  604 | (423.5, 168.9)  | (423.5, 191.4)
  605 | (412.0, 168.9)  | (412.0, 191.4)
  606 | (400.5, 168.9)  | (400.5, 191.4)
  607 | (389.0, 168.9)  | (389.0, 191.4)
  608 | (377.4, 168.9)  | (377.4, 191.4)
  609 | (365.9, 168.9)  | (365.9, 191.4)
  610 | (354.4, 168.9)  | (354.4, 191.4)
  611 | (342.8, 168.9)  | (342.8, 191.4)
  612 | (331.3, 168.9)  | (331.3, 191.4)
  613 | (319.8, 168.9)  | (319.8, 191.4)
  614 | (308.2, 168.9)  | (308.2, 191.4)
  615 | (296.7, 168.9)  | (296.7, 191.4)
  616 | (285.2, 168.9)  | (285.2, 191.4)
  617 | (273.7, 168.9)  | (273.7, 191.4)
  618 | (262.1, 168.9)  | (262.1, 191.4)
  619 | (250.6, 168.9)  | (250.6, 191.4)
  620 | (239.1, 168.9)  | (239.1, 191.4)
  621 | (227.5, 168.9)  | (227.5, 191.4)
  622 | (216.0, 168.9)  | (216.0, 191.4)
  623 | (204.5, 168.9)  | (204.5, 191.4)
  624 | (192.9, 168.9)  | (192.9, 191.4)
  625 | (181.4, 168.9)  | (181.4, 191.4)
  626 | (169.9, 168.9)  | (169.9, 191.4)
  627 | (158.4, 168.9)  | (158.4, 191.4)
  628 | (146.8, 168.9)  | (146.8, 191.4)
  629 | (135.3, 168.9)  | (135.3, 191.4)
  630 | (123.8, 168.9)  | (123.8, 191.4)
  631 | (112.2, 168.9)  | (112.2, 191.4)
  632 | (100.7, 168.9)  | (100.7, 191.4)
  633 | (89.2, 168.9)   | (89.2, 191.4)
  634 | (77.6, 168.9)   | (77.6, 191.4)
  635 | (66.1, 168.9)   | (66.1, 191.4)
  636 | (54.6, 168.9)   | (54.6, 191.4)
  637 | (43.1, 168.9)   | (43.1, 191.4)
  638 | (31.5, 168.9)   | (31.5, 191.4)
  639 | (20.0, 168.9)   | (20.0, 191.4)
  640 | (20.0, 179.7)   | (20.0, 202.2)
  641 | (31.5, 179.7)   | (31.5, 202.2)
  642 | (43.1, 179.7)   | (43.1, 202.2)
  643 | (54.6, 179.7)   | (54.6, 202.2)
  644 | (66.1, 179.7)   | (66.1, 202.2)
  645 | (77.7, 179.7)   | (77.7, 202.2)
  646 | (89.2, 179.7)   | (89.2, 202.2)
  647 | (100.7, 179.7)  | (100.7, 202.2)
  648 | (112.2, 179.7)  | (112.2, 202.2)
  649 | (123.8, 179.7)  | (123.8, 202.2)
  650 | (135.3, 179.7)  | (135.3, 202.2)
  651 | (146.8, 179.7)  | (146.8, 202.2)
  652 | (158.4, 179.7)  | (158.4, 202.2)
  653 | (169.9, 179.7)  | (169.9, 202.2)
  654 | (181.4, 179.7)  | (181.4, 202.2)
  655 | (192.9, 179.7)  | (192.9, 202.2)
  656 | (204.5, 179.7)  | (204.5, 202.2)
  657 | (216.0, 179.7)  | (216.0, 202.2)
  658 | (227.5, 179.7)  | (227.5, 202.2)
  659 | (239.1, 179.7)  | (239.1, 202.2)
  660 | (250.6, 179.7)  | (250.6, 202.2)
  661 | (262.1, 179.7)  | (262.1, 202.2)
  662 | (273.7, 179.7)  | (273.7, 202.2)
  663 | (285.2, 179.7)  | (285.2, 202.2)
  664 | (296.7, 179.7)  | (296.7, 202.2)
  665 | (308.2, 179.7)  | (308.2, 202.2)
  666 | (319.8, 179.7)  | (319.8, 202.2)
  667 | (331.3, 179.7)  | (331.3, 202.2)
  668 | (342.8, 179.7)  | (342.8, 202.2)
  669 | (354.4, 179.7)  | (354.4, 202.2)
  670 | (365.9, 179.7)  | (365.9, 202.2)
  671 | (377.4, 179.7)  | (377.4, 202.2)
  672 | (389.0, 179.7)  | (389.0, 202.2)
  673 | (400.5, 179.7)  | (400.5, 202.2)
  674 | (412.0, 179.7)  | (412.0, 202.2)
  675 | (423.5, 179.7)  | (423.5, 202.2)
  676 | (435.1, 179.7)  | (435.1, 202.2)
  677 | (446.6, 179.7)  | (446.6, 202.2)
  678 | (458.1, 179.7)  | (458.1, 202.2)
  679 | (469.7, 179.7)  | (469.7, 202.2)
  680 | (469.7, 190.4)  | (469.7, 212.9)
  681 | (458.1, 190.4)  | (458.1, 212.9)
  682 | (446.6, 190.4)  | (446.6, 212.9)
  683 | (435.1, 190.4)  | (435.1, 212.9)
  684 | (423.5, 190.4)  | (423.5, 212.9)
  685 | (412.0, 190.4)  | (412.0, 212.9)
  686 | (400.5, 190.4)  | (400.5, 212.9)
  687 | (389.0, 190.4)  | (389.0, 212.9)
  688 | (377.4, 190.4)  | (377.4, 212.9)
  689 | (365.9, 190.4)  | (365.9, 212.9)
  690 | (354.4, 190.4)  | (354.4, 212.9)
  691 | (342.8, 190.4)  | (342.8, 212.9)
  692 | (331.3, 190.4)  | (331.3, 212.9)
  693 | (319.8, 190.4)  | (319.8, 212.9)
  694 | (308.2, 190.4)  | (308.2, 212.9)
  695 | (296.7, 190.4)  | (296.7, 212.9)
  696 | (285.2, 190.4)  | (285.2, 212.9)
  697 | (273.7, 190.4)  | (273.7, 212.9)
  698 | (262.1, 190.4)  | (262.1, 212.9)
  699 | (250.6, 190.4)  | (250.6, 212.9)
  700 | (239.1, 190.4)  | (239.1, 212.9)
  701 | (227.5, 190.4)  | (227.5, 212.9)
  702 | (216.0, 190.4)  | (216.0, 212.9)
  703 | (204.5, 190.4)  | (204.5, 212.9)
  704 | (192.9, 190.4)  | (192.9, 212.9)
  705 | (181.4, 190.4)  | (181.4, 212.9)
  706 | (169.9, 190.4)  | (169.9, 212.9)
  707 | (158.4, 190.4)  | (158.4, 212.9)
  708 | (146.8, 190.4)  | (146.8, 212.9)
  709 | (135.3, 190.4)  | (135.3, 212.9)
  710 | (123.8, 190.4)  | (123.8, 212.9)
  711 | (112.2, 190.4)  | (112.2, 212.9)
  712 | (100.7, 190.4)  | (100.7, 212.9)
  713 | (89.2, 190.4)   | (89.2, 212.9)
  714 | (77.6, 190.4)   | (77.6, 212.9)
  715 | (66.1, 190.4)   | (66.1, 212.9)
  716 | (54.6, 190.4)   | (54.6, 212.9)
  717 | (43.1, 190.4)   | (43.1, 212.9)
  718 | (31.5, 190.4)   | (31.5, 212.9)
  719 | (20.0, 190.4)   | (20.0, 212.9)
  720 | (20.0, 201.2)   | (20.0, 223.7)
  721 | (31.5, 201.2)   | (31.5, 223.7)
  722 | (43.1, 201.2)   | (43.1, 223.7)
  723 | (54.6, 201.2)   | (54.6, 223.7)
  724 | (66.1, 201.2)   | (66.1, 223.7)
  725 | (77.7, 201.2)   | (77.7, 223.7)
  726 | (89.2, 201.2)   | (89.2, 223.7)
  727 | (100.7, 201.2)  | (100.7, 223.7)
  728 | (112.2, 201.2)  | (112.2, 223.7)
  729 | (123.8, 201.2)  | (123.8, 223.7)
  730 | (135.3, 201.2)  | (135.3, 223.7)
  731 | (146.8, 201.2)  | (146.8, 223.7)
  732 | (158.4, 201.2)  | (158.4, 223.7)
  733 | (169.9, 201.2)  | (169.9, 223.7)
  734 | (181.4, 201.2)  | (181.4, 223.7)
  735 | (192.9, 201.2)  | (192.9, 223.7)
  736 | (204.5, 201.2)  | (204.5, 223.7)
  737 | (216.0, 201.2)  | (216.0, 223.7)
  738 | (227.5, 201.2)  | (227.5, 223.7)
  739 | (239.1, 201.2)  | (239.1, 223.7)
  740 | (250.6, 201.2)  | (250.6, 223.7)
  741 | (262.1, 201.2)  | (262.1, 223.7)
  742 | (273.7, 201.2)  | (273.7, 223.7)
  743 | (285.2, 201.2)  | (285.2, 223.7)
  744 | (296.7, 201.2)  | (296.7, 223.7)
  745 | (308.2, 201.2)  | (308.2, 223.7)
  746 | (319.8, 201.2)  | (319.8, 223.7)
  747 | (331.3, 201.2)  | (331.3, 223.7)
  748 | (342.8, 201.2)  | (342.8, 223.7)
  749 | (354.4, 201.2)  | (354.4, 223.7)
  750 | (365.9, 201.2)  | (365.9, 223.7)
  751 | (377.4, 201.2)  | (377.4, 223.7)
  752 | (389.0, 201.2)  | (389.0, 223.7)
  753 | (400.5, 201.2)  | (400.5, 223.7)
  754 | (412.0, 201.2)  | (412.0, 223.7)
  755 | (423.5, 201.2)  | (423.5, 223.7)
  756 | (435.1, 201.2)  | (435.1, 223.7)
  757 | (446.6, 201.2)  | (446.6, 223.7)
  758 | (458.1, 201.2)  | (458.1, 223.7)
  759 | (469.7, 201.2)  | (469.7, 223.7)
  760 | (469.7, 211.9)  | (469.7, 234.4)
  761 | (458.1, 211.9)  | (458.1, 234.4)
  762 | (446.6, 211.9)  | (446.6, 234.4)
  763 | (435.1, 211.9)  | (435.1, 234.4)
  764 | (423.5, 211.9)  | (423.5, 234.4)
  765 | (412.0, 211.9)  | (412.0, 234.4)
  766 | (400.5, 211.9)  | (400.5, 234.4)
  767 | (389.0, 211.9)  | (389.0, 234.4)
  768 | (377.4, 211.9)  | (377.4, 234.4)
  769 | (365.9, 211.9)  | (365.9, 234.4)
  770 | (354.4, 211.9)  | (354.4, 234.4)
  771 | (342.8, 211.9)  | (342.8, 234.4)
  772 | (331.3, 211.9)  | (331.3, 234.4)
  773 | (319.8, 211.9)  | (319.8, 234.4)
  774 | (308.2, 211.9)  | (308.2, 234.4)
  775 | (296.7, 211.9)  | (296.7, 234.4)
  776 | (285.2, 211.9)  | (285.2, 234.4)
  777 | (273.7, 211.9)  | (273.7, 234.4)
  778 | (262.1, 211.9)  | (262.1, 234.4)
  779 | (250.6, 211.9)  | (250.6, 234.4)
  780 | (239.1, 211.9)  | (239.1, 234.4)
  781 | (227.5, 211.9)  | (227.5, 234.4)
  782 | (216.0, 211.9)  | (216.0, 234.4)
  783 | (204.5, 211.9)  | (204.5, 234.4)
  784 | (192.9, 211.9)  | (192.9, 234.4)
  785 | (181.4, 211.9)  | (181.4, 234.4)
  786 | (169.9, 211.9)  | (169.9, 234.4)
  787 | (158.4, 211.9)  | (158.4, 234.4)
  788 | (146.8, 211.9)  | (146.8, 234.4)
  789 | (135.3, 211.9)  | (135.3, 234.4)
  790 | (123.8, 211.9)  | (123.8, 234.4)
  791 | (112.2, 211.9)  | (112.2, 234.4)
  792 | (100.7, 211.9)  | (100.7, 234.4)
  793 | (89.2, 211.9)   | (89.2, 234.4)
  794 | (77.6, 211.9)   | (77.6, 234.4)
  795 | (66.1, 211.9)   | (66.1, 234.4)
  796 | (54.6, 211.9)   | (54.6, 234.4)
  797 | (43.1, 211.9)   | (43.1, 234.4)
  798 | (31.5, 211.9)   | (31.5, 234.4)
  799 | (20.0, 211.9)   | (20.0, 234.4)
  800 | (20.0, 222.7)   | (20.0, 245.2)
  801 | (31.5, 222.7)   | (31.5, 245.2)
  802 | (43.1, 222.7)   | (43.1, 245.2)
  803 | (54.6, 222.7)   | (54.6, 245.2)
  804 | (66.1, 222.7)   | (66.1, 245.2)
  805 | (77.7, 222.7)   | (77.7, 245.2)
  806 | (89.2, 222.7)   | (89.2, 245.2)
  807 | (100.7, 222.7)  | (100.7, 245.2)
  808 | (112.2, 222.7)  | (112.2, 245.2)
  809 | (123.8, 222.7)  | (123.8, 245.2)
  810 | (135.3, 222.7)  | (135.3, 245.2)
  811 | (146.8, 222.7)  | (146.8, 245.2)
  812 | (158.4, 222.7)  | (158.4, 245.2)
  813 | (169.9, 222.7)  | (169.9, 245.2)
  814 | (181.4, 222.7)  | (181.4, 245.2)
  815 | (192.9, 222.7)  | (192.9, 245.2)
  816 | (204.5, 222.7)  | (204.5, 245.2)
  817 | (216.0, 222.7)  | (216.0, 245.2)
  818 | (227.5, 222.7)  | (227.5, 245.2)
  819 | (239.1, 222.7)  | (239.1, 245.2)
  820 | (250.6, 222.7)  | (250.6, 245.2)
  821 | (262.1, 222.7)  | (262.1, 245.2)
  822 | (273.7, 222.7)  | (273.7, 245.2)
  823 | (285.2, 222.7)  | (285.2, 245.2)
  824 | (296.7, 222.7)  | (296.7, 245.2)
  825 | (308.2, 222.7)  | (308.2, 245.2)
  826 | (319.8, 222.7)  | (319.8, 245.2)
  827 | (331.3, 222.7)  | (331.3, 245.2)
  828 | (342.8, 222.7)  | (342.8, 245.2)
  829 | (354.4, 222.7)  | (354.4, 245.2)
  830 | (365.9, 222.7)  | (365.9, 245.2)
  831 | (377.4, 222.7)  | (377.4, 245.2)
  832 | (389.0, 222.7)  | (389.0, 245.2)
  833 | (400.5, 222.7)  | (400.5, 245.2)
  834 | (412.0, 222.7)  | (412.0, 245.2)
  835 | (423.5, 222.7)  | (423.5, 245.2)
  836 | (435.1, 222.7)  | (435.1, 245.2)
  837 | (446.6, 222.7)  | (446.6, 245.2)
  838 | (458.1, 222.7)  | (458.1, 245.2)
  839 | (469.7, 222.7)  | (469.7, 245.2)
  840 | (469.7, 233.5)  | (469.7, 256.0)
  841 | (458.1, 233.5)  | (458.1, 256.0)
  842 | (446.6, 233.5)  | (446.6, 256.0)
  843 | (435.1, 233.5)  | (435.1, 256.0)
  844 | (423.5, 233.5)  | (423.5, 256.0)
  845 | (412.0, 233.5)  | (412.0, 256.0)
  846 | (400.5, 233.5)  | (400.5, 256.0)
  847 | (389.0, 233.5)  | (389.0, 256.0)
  848 | (377.4, 233.5)  | (377.4, 256.0)
  849 | (365.9, 233.5)  | (365.9, 256.0)
  850 | (354.4, 233.5)  | (354.4, 256.0)
  851 | (342.8, 233.5)  | (342.8, 256.0)
  852 | (331.3, 233.5)  | (331.3, 256.0)
  853 | (319.8, 233.5)  | (319.8, 256.0)
  854 | (308.2, 233.5)  | (308.2, 256.0)
  855 | (296.7, 233.5)  | (296.7, 256.0)
  856 | (285.2, 233.5)  | (285.2, 256.0)
  857 | (273.7, 233.5)  | (273.7, 256.0)
  858 | (262.1, 233.5)  | (262.1, 256.0)
  859 | (250.6, 233.5)  | (250.6, 256.0)
  860 | (239.1, 233.5)  | (239.1, 256.0)
  861 | (227.5, 233.5)  | (227.5, 256.0)
  862 | (216.0, 233.5)  | (216.0, 256.0)
  863 | (204.5, 233.5)  | (204.5, 256.0)
  864 | (192.9, 233.5)  | (192.9, 256.0)
  865 | (181.4, 233.5)  | (181.4, 256.0)
  866 | (169.9, 233.5)  | (169.9, 256.0)
  867 | (158.4, 233.5)  | (158.4, 256.0)
  868 | (146.8, 233.5)  | (146.8, 256.0)
  869 | (135.3, 233.5)  | (135.3, 256.0)
  870 | (123.8, 233.5)  | (123.8, 256.0)
  871 | (112.2, 233.5)  | (112.2, 256.0)
  872 | (100.7, 233.5)  | (100.7, 256.0)
  873 | (89.2, 233.5)   | (89.2, 256.0)
  874 | (77.6, 233.5)   | (77.6, 256.0)
  875 | (66.1, 233.5)   | (66.1, 256.0)
  876 | (54.6, 233.5)   | (54.6, 256.0)
  877 | (43.1, 233.5)   | (43.1, 256.0)
  878 | (31.5, 233.5)   | (31.5, 256.0)
  879 | (20.0, 233.5)   | (20.0, 256.0)
  880 | (20.0, 244.2)   | (20.0, 266.7)
  881 | (31.5, 244.2)   | (31.5, 266.7)
  882 | (43.1, 244.2)   | (43.1, 266.7)
  883 | (54.6, 244.2)   | (54.6, 266.7)
  884 | (66.1, 244.2)   | (66.1, 266.7)
  885 | (77.7, 244.2)   | (77.7, 266.7)
  886 | (89.2, 244.2)   | (89.2, 266.7)
  887 | (100.7, 244.2)  | (100.7, 266.7)
  888 | (112.2, 244.2)  | (112.2, 266.7)
  889 | (123.8, 244.2)  | (123.8, 266.7)
  890 | (135.3, 244.2)  | (135.3, 266.7)
  891 | (146.8, 244.2)  | (146.8, 266.7)
  892 | (158.4, 244.2)  | (158.4, 266.7)
  893 | (169.9, 244.2)  | (169.9, 266.7)
  894 | (181.4, 244.2)  | (181.4, 266.7)
  895 | (192.9, 244.2)  | (192.9, 266.7)
  896 | (204.5, 244.2)  | (204.5, 266.7)
  897 | (216.0, 244.2)  | (216.0, 266.7)
  898 | (227.5, 244.2)  | (227.5, 266.7)
  899 | (239.1, 244.2)  | (239.1, 266.7)
  900 | (250.6, 244.2)  | (250.6, 266.7)
  901 | (262.1, 244.2)  | (262.1, 266.7)
  902 | (273.7, 244.2)  | (273.7, 266.7)
  903 | (285.2, 244.2)  | (285.2, 266.7)
  904 | (296.7, 244.2)  | (296.7, 266.7)
  905 | (308.2, 244.2)  | (308.2, 266.7)
  906 | (319.8, 244.2)  | (319.8, 266.7)
  907 | (331.3, 244.2)  | (331.3, 266.7)
  908 | (342.8, 244.2)  | (342.8, 266.7)
  909 | (354.4, 244.2)  | (354.4, 266.7)
  910 | (365.9, 244.2)  | (365.9, 266.7)
  911 | (377.4, 244.2)  | (377.4, 266.7)
  912 | (389.0, 244.2)  | (389.0, 266.7)
  913 | (400.5, 244.2)  | (400.5, 266.7)
  914 | (412.0, 244.2)  | (412.0, 266.7)
  915 | (423.5, 244.2)  | (423.5, 266.7)
  916 | (435.1, 244.2)  | (435.1, 266.7)
  917 | (446.6, 244.2)  | (446.6, 266.7)
  918 | (458.1, 244.2)  | (458.1, 266.7)
  919 | (469.7, 244.2)  | (469.7, 266.7)
  920 | (469.7, 255.0)  | (469.7, 277.5)
  921 | (458.1, 255.0)  | (458.1, 277.5)
  922 | (446.6, 255.0)  | (446.6, 277.5)
  923 | (435.1, 255.0)  | (435.1, 277.5)
  924 | (423.5, 255.0)  | (423.5, 277.5)
  925 | (412.0, 255.0)  | (412.0, 277.5)
  926 | (400.5, 255.0)  | (400.5, 277.5)
  927 | (389.0, 255.0)  | (389.0, 277.5)
  928 | (377.4, 255.0)  | (377.4, 277.5)
  929 | (365.9, 255.0)  | (365.9, 277.5)
  930 | (354.4, 255.0)  | (354.4, 277.5)
  931 | (342.8, 255.0)  | (342.8, 277.5)
  932 | (331.3, 255.0)  | (331.3, 277.5)
  933 | (319.8, 255.0)  | (319.8, 277.5)
  934 | (308.2, 255.0)  | (308.2, 277.5)
  935 | (296.7, 255.0)  | (296.7, 277.5)
  936 | (285.2, 255.0)  | (285.2, 277.5)
  937 | (273.7, 255.0)  | (273.7, 277.5)
  938 | (262.1, 255.0)  | (262.1, 277.5)
  939 | (250.6, 255.0)  | (250.6, 277.5)
  940 | (239.1, 255.0)  | (239.1, 277.5)
  941 | (227.5, 255.0)  | (227.5, 277.5)
  942 | (216.0, 255.0)  | (216.0, 277.5)
  943 | (204.5, 255.0)  | (204.5, 277.5)
  944 | (192.9, 255.0)  | (192.9, 277.5)
  945 | (181.4, 255.0)  | (181.4, 277.5)
  946 | (169.9, 255.0)  | (169.9, 277.5)
  947 | (158.4, 255.0)  | (158.4, 277.5)
  948 | (146.8, 255.0)  | (146.8, 277.5)
  949 | (135.3, 255.0)  | (135.3, 277.5)
  950 | (123.8, 255.0)  | (123.8, 277.5)
  951 | (112.2, 255.0)  | (112.2, 277.5)
  952 | (100.7, 255.0)  | (100.7, 277.5)
  953 | (89.2, 255.0)   | (89.2, 277.5)
  954 | (77.6, 255.0)   | (77.6, 277.5)
  955 | (66.1, 255.0)   | (66.1, 277.5)
  956 | (54.6, 255.0)   | (54.6, 277.5)
  957 | (43.1, 255.0)   | (43.1, 277.5)
  958 | (31.5, 255.0)   | (31.5, 277.5)
  959 | (20.0, 255.0)   | (20.0, 277.5)
  960 | (20.0, 265.7)   | (20.0, 288.2)
  961 | (31.5, 265.7)   | (31.5, 288.2)
  962 | (43.1, 265.7)   | (43.1, 288.2)
  963 | (54.6, 265.7)   | (54.6, 288.2)
  964 | (66.1, 265.7)   | (66.1, 288.2)
  965 | (77.7, 265.7)   | (77.7, 288.2)
  966 | (89.2, 265.7)   | (89.2, 288.2)
  967 | (100.7, 265.7)  | (100.7, 288.2)
  968 | (112.2, 265.7)  | (112.2, 288.2)
  969 | (123.8, 265.7)  | (123.8, 288.2)
  970 | (135.3, 265.7)  | (135.3, 288.2)
  971 | (146.8, 265.7)  | (146.8, 288.2)
  972 | (158.4, 265.7)  | (158.4, 288.2)
  973 | (169.9, 265.7)  | (169.9, 288.2)
  974 | (181.4, 265.7)  | (181.4, 288.2)
  975 | (192.9, 265.7)  | (192.9, 288.2)
  976 | (204.5, 265.7)  | (204.5, 288.2)
  977 | (216.0, 265.7)  | (216.0, 288.2)
  978 | (227.5, 265.7)  | (227.5, 288.2)
  979 | (239.1, 265.7)  | (239.1, 288.2)
  980 | (250.6, 265.7)  | (250.6, 288.2)
  981 | (262.1, 265.7)  | (262.1, 288.2)
  982 | (273.7, 265.7)  | (273.7, 288.2)
  983 | (285.2, 265.7)  | (285.2, 288.2)
  984 | (296.7, 265.7)  | (296.7, 288.2)
  985 | (308.2, 265.7)  | (308.2, 288.2)
  986 | (319.8, 265.7)  | (319.8, 288.2)
  987 | (331.3, 265.7)  | (331.3, 288.2)
  988 | (342.8, 265.7)  | (342.8, 288.2)
  989 | (354.4, 265.7)  | (354.4, 288.2)
  990 | (365.9, 265.7)  | (365.9, 288.2)
  991 | (377.4, 265.7)  | (377.4, 288.2)
  992 | (389.0, 265.7)  | (389.0, 288.2)
  993 | (400.5, 265.7)  | (400.5, 288.2)
  994 | (412.0, 265.7)  | (412.0, 288.2)
  995 | (423.5, 265.7)  | (423.5, 288.2)
  996 | (435.1, 265.7)  | (435.1, 288.2)
  997 | (446.6, 265.7)  | (446.6, 288.2)
  998 | (458.1, 265.7)  | (458.1, 288.2)
  999 | (469.7, 265.7)  | (469.7, 288.2)
  1000| (469.7, 276.5)  | (469.7, 299.0)
  1001| (458.1, 276.5)  | (458.1, 299.0)
  1002| (446.6, 276.5)  | (446.6, 299.0)
  1003| (435.1, 276.5)  | (435.1, 299.0)
  1004| (423.5, 276.5)  | (423.5, 299.0)
  1005| (412.0, 276.5)  | (412.0, 299.0)
  1006| (400.5, 276.5)  | (400.5, 299.0)
  1007| (389.0, 276.5)  | (389.0, 299.0)
  1008| (377.4, 276.5)  | (377.4, 299.0)
  1009| (365.9, 276.5)  | (365.9, 299.0)
  1010| (354.4, 276.5)  | (354.4, 299.0)
  1011| (342.8, 276.5)  | (342.8, 299.0)
  1012| (331.3, 276.5)  | (331.3, 299.0)
  1013| (319.8, 276.5)  | (319.8, 299.0)
  1014| (308.2, 276.5)  | (308.2, 299.0)
  1015| (296.7, 276.5)  | (296.7, 299.0)
  1016| (285.2, 276.5)  | (285.2, 299.0)
  1017| (273.7, 276.5)  | (273.7, 299.0)
  1018| (262.1, 276.5)  | (262.1, 299.0)
  1019| (250.6, 276.5)  | (250.6, 299.0)
  1020| (239.1, 276.5)  | (239.1, 299.0)
  1021| (227.5, 276.5)  | (227.5, 299.0)
  1022| (216.0, 276.5)  | (216.0, 299.0)
  1023| (204.5, 276.5)  | (204.5, 299.0)
  1024| (192.9, 276.5)  | (192.9, 299.0)
  1025| (181.4, 276.5)  | (181.4, 299.0)
  1026| (169.9, 276.5)  | (169.9, 299.0)
  1027| (158.4, 276.5)  | (158.4, 299.0)
  1028| (146.8, 276.5)  | (146.8, 299.0)
  1029| (135.3, 276.5)  | (135.3, 299.0)
  1030| (123.8, 276.5)  | (123.8, 299.0)
  1031| (112.2, 276.5)  | (112.2, 299.0)
  1032| (100.7, 276.5)  | (100.7, 299.0)
  1033| (89.2, 276.5)   | (89.2, 299.0)
  1034| (77.6, 276.5)   | (77.6, 299.0)
  1035| (66.1, 276.5)   | (66.1, 299.0)
  1036| (54.6, 276.5)   | (54.6, 299.0)
  1037| (43.1, 276.5)   | (43.1, 299.0)
  1038| (31.5, 276.5)   | (31.5, 299.0)
  1039| (20.0, 276.5)   | (20.0, 299.0)
  1040| (20.0, 287.3)   | (20.0, 309.8)
  1041| (31.5, 287.3)   | (31.5, 309.8)
  1042| (43.1, 287.3)   | (43.1, 309.8)
  1043| (54.6, 287.3)   | (54.6, 309.8)
  1044| (66.1, 287.3)   | (66.1, 309.8)
  1045| (77.7, 287.3)   | (77.7, 309.8)
  1046| (89.2, 287.3)   | (89.2, 309.8)
  1047| (100.7, 287.3)  | (100.7, 309.8)
  1048| (112.2, 287.3)  | (112.2, 309.8)
  1049| (123.8, 287.3)  | (123.8, 309.8)
  1050| (135.3, 287.3)  | (135.3, 309.8)
  1051| (146.8, 287.3)  | (146.8, 309.8)
  1052| (158.4, 287.3)  | (158.4, 309.8)
  1053| (169.9, 287.3)  | (169.9, 309.8)
  1054| (181.4, 287.3)  | (181.4, 309.8)
  1055| (192.9, 287.3)  | (192.9, 309.8)
  1056| (204.5, 287.3)  | (204.5, 309.8)
  1057| (216.0, 287.3)  | (216.0, 309.8)
  1058| (227.5, 287.3)  | (227.5, 309.8)
  1059| (239.1, 287.3)  | (239.1, 309.8)
  1060| (250.6, 287.3)  | (250.6, 309.8)
  1061| (262.1, 287.3)  | (262.1, 309.8)
  1062| (273.7, 287.3)  | (273.7, 309.8)
  1063| (285.2, 287.3)  | (285.2, 309.8)
  1064| (296.7, 287.3)  | (296.7, 309.8)
  1065| (308.2, 287.3)  | (308.2, 309.8)
  1066| (319.8, 287.3)  | (319.8, 309.8)
  1067| (331.3, 287.3)  | (331.3, 309.8)
  1068| (342.8, 287.3)  | (342.8, 309.8)
  1069| (354.4, 287.3)  | (354.4, 309.8)
  1070| (365.9, 287.3)  | (365.9, 309.8)
  1071| (377.4, 287.3)  | (377.4, 309.8)
  1072| (389.0, 287.3)  | (389.0, 309.8)
  1073| (400.5, 287.3)  | (400.5, 309.8)
  1074| (412.0, 287.3)  | (412.0, 309.8)
  1075| (423.5, 287.3)  | (423.5, 309.8)
  1076| (435.1, 287.3)  | (435.1, 309.8)
  1077| (446.6, 287.3)  | (446.6, 309.8)
  1078| (458.1, 287.3)  | (458.1, 309.8)
  1079| (469.7, 287.3)  | (469.7, 309.8)
  1080| (469.7, 298.0)  | (469.7, 320.5)
  1081| (458.1, 298.0)  | (458.1, 320.5)
  1082| (446.6, 298.0)  | (446.6, 320.5)
  1083| (435.1, 298.0)  | (435.1, 320.5)
  1084| (423.5, 298.0)  | (423.5, 320.5)
  1085| (412.0, 298.0)  | (412.0, 320.5)
  1086| (400.5, 298.0)  | (400.5, 320.5)
  1087| (389.0, 298.0)  | (389.0, 320.5)
  1088| (377.4, 298.0)  | (377.4, 320.5)
  1089| (365.9, 298.0)  | (365.9, 320.5)
  1090| (354.4, 298.0)  | (354.4, 320.5)
  1091| (342.8, 298.0)  | (342.8, 320.5)
  1092| (331.3, 298.0)  | (331.3, 320.5)
  1093| (319.8, 298.0)  | (319.8, 320.5)
  1094| (308.2, 298.0)  | (308.2, 320.5)
  1095| (296.7, 298.0)  | (296.7, 320.5)
  1096| (285.2, 298.0)  | (285.2, 320.5)
  1097| (273.7, 298.0)  | (273.7, 320.5)
  1098| (262.1, 298.0)  | (262.1, 320.5)
  1099| (250.6, 298.0)  | (250.6, 320.5)
  1100| (239.1, 298.0)  | (239.1, 320.5)
  1101| (227.5, 298.0)  | (227.5, 320.5)
  1102| (216.0, 298.0)  | (216.0, 320.5)
  1103| (204.5, 298.0)  | (204.5, 320.5)
  1104| (192.9, 298.0)  | (192.9, 320.5)
  1105| (181.4, 298.0)  | (181.4, 320.5)
  1106| (169.9, 298.0)  | (169.9, 320.5)
  1107| (158.4, 298.0)  | (158.4, 320.5)
  1108| (146.8, 298.0)  | (146.8, 320.5)
  1109| (135.3, 298.0)  | (135.3, 320.5)
  1110| (123.8, 298.0)  | (123.8, 320.5)
  1111| (112.2, 298.0)  | (112.2, 320.5)
  1112| (100.7, 298.0)  | (100.7, 320.5)
  1113| (89.2, 298.0)   | (89.2, 320.5)
  1114| (77.6, 298.0)   | (77.6, 320.5)
  1115| (66.1, 298.0)   | (66.1, 320.5)
  1116| (54.6, 298.0)   | (54.6, 320.5)
  1117| (43.1, 298.0)   | (43.1, 320.5)
  1118| (31.5, 298.0)   | (31.5, 320.5)
  1119| (20.0, 298.0)   | (20.0, 320.5)
  1120| (20.0, 308.8)   | (20.0, 331.3)
  1121| (31.5, 308.8)   | (31.5, 331.3)
  1122| (43.1, 308.8)   | (43.1, 331.3)
  1123| (54.6, 308.8)   | (54.6, 331.3)
  1124| (66.1, 308.8)   | (66.1, 331.3)
  1125| (77.7, 308.8)   | (77.7, 331.3)
  1126| (89.2, 308.8)   | (89.2, 331.3)
  1127| (100.7, 308.8)  | (100.7, 331.3)
  1128| (112.2, 308.8)  | (112.2, 331.3)
  1129| (123.8, 308.8)  | (123.8, 331.3)
  1130| (135.3, 308.8)  | (135.3, 331.3)
  1131| (146.8, 308.8)  | (146.8, 331.3)
  1132| (158.4, 308.8)  | (158.4, 331.3)
  1133| (169.9, 308.8)  | (169.9, 331.3)
  1134| (181.4, 308.8)  | (181.4, 331.3)
  1135| (192.9, 308.8)  | (192.9, 331.3)
  1136| (204.5, 308.8)  | (204.5, 331.3)
  1137| (216.0, 308.8)  | (216.0, 331.3)
  1138| (227.5, 308.8)  | (227.5, 331.3)
  1139| (239.1, 308.8)  | (239.1, 331.3)
  1140| (250.6, 308.8)  | (250.6, 331.3)
  1141| (262.1, 308.8)  | (262.1, 331.3)
  1142| (273.7, 308.8)  | (273.7, 331.3)
  1143| (285.2, 308.8)  | (285.2, 331.3)
  1144| (296.7, 308.8)  | (296.7, 331.3)
  1145| (308.2, 308.8)  | (308.2, 331.3)
  1146| (319.8, 308.8)  | (319.8, 331.3)
  1147| (331.3, 308.8)  | (331.3, 331.3)
  1148| (342.8, 308.8)  | (342.8, 331.3)
  1149| (354.4, 308.8)  | (354.4, 331.3)
  1150| (365.9, 308.8)  | (365.9, 331.3)
  1151| (377.4, 308.8)  | (377.4, 331.3)
  1152| (389.0, 308.8)  | (389.0, 331.3)
  1153| (400.5, 308.8)  | (400.5, 331.3)
  1154| (412.0, 308.8)  | (412.0, 331.3)
  1155| (423.5, 308.8)  | (423.5, 331.3)
  1156| (435.1, 308.8)  | (435.1, 331.3)
  1157| (446.6, 308.8)  | (446.6, 331.3)
  1158| (458.1, 308.8)  | (458.1, 331.3)
  1159| (469.7, 308.8)  | (469.7, 331.3)
  1160| (469.7, 319.5)  | (469.7, 342.0)
  1161| (458.1, 319.5)  | (458.1, 342.0)
  1162| (446.6, 319.5)  | (446.6, 342.0)
  1163| (435.1, 319.5)  | (435.1, 342.0)
  1164| (423.5, 319.5)  | (423.5, 342.0)
  1165| (412.0, 319.5)  | (412.0, 342.0)
  1166| (400.5, 319.5)  | (400.5, 342.0)
  1167| (389.0, 319.5)  | (389.0, 342.0)
  1168| (377.4, 319.5)  | (377.4, 342.0)
  1169| (365.9, 319.5)  | (365.9, 342.0)
  1170| (354.4, 319.5)  | (354.4, 342.0)
  1171| (342.8, 319.5)  | (342.8, 342.0)
  1172| (331.3, 319.5)  | (331.3, 342.0)
  1173| (319.8, 319.5)  | (319.8, 342.0)
  1174| (308.2, 319.5)  | (308.2, 342.0)
  1175| (296.7, 319.5)  | (296.7, 342.0)
  1176| (285.2, 319.5)  | (285.2, 342.0)
  1177| (273.7, 319.5)  | (273.7, 342.0)
  1178| (262.1, 319.5)  | (262.1, 342.0)
  1179| (250.6, 319.5)  | (250.6, 342.0)
  1180| (239.1, 319.5)  | (239.1, 342.0)
  1181| (227.5, 319.5)  | (227.5, 342.0)
  1182| (216.0, 319.5)  | (216.0, 342.0)
  1183| (204.5, 319.5)  | (204.5, 342.0)
  1184| (192.9, 319.5)  | (192.9, 342.0)
  1185| (181.4, 319.5)  | (181.4, 342.0)
  1186| (169.9, 319.5)  | (169.9, 342.0)
  1187| (158.4, 319.5)  | (158.4, 342.0)
  1188| (146.8, 319.5)  | (146.8, 342.0)
  1189| (135.3, 319.5)  | (135.3, 342.0)
  1190| (123.8, 319.5)  | (123.8, 342.0)
  1191| (112.2, 319.5)  | (112.2, 342.0)
  1192| (100.7, 319.5)  | (100.7, 342.0)
  1193| (89.2, 319.5)   | (89.2, 342.0)
  1194| (77.6, 319.5)   | (77.6, 342.0)
  1195| (66.1, 319.5)   | (66.1, 342.0)
  1196| (54.6, 319.5)   | (54.6, 342.0)
  1197| (43.1, 319.5)   | (43.1, 342.0)
  1198| (31.5, 319.5)   | (31.5, 342.0)
  1199| (20.0, 319.5)   | (20.0, 342.0)
  1200| (20.0, 330.3)   | (20.0, 352.8)
  1201| (31.5, 330.3)   | (31.5, 352.8)
  1202| (43.1, 330.3)   | (43.1, 352.8)
  1203| (54.6, 330.3)   | (54.6, 352.8)
  1204| (66.1, 330.3)   | (66.1, 352.8)
  1205| (77.7, 330.3)   | (77.7, 352.8)
  1206| (89.2, 330.3)   | (89.2, 352.8)
  1207| (100.7, 330.3)  | (100.7, 352.8)
  1208| (112.2, 330.3)  | (112.2, 352.8)
  1209| (123.8, 330.3)  | (123.8, 352.8)
  1210| (135.3, 330.3)  | (135.3, 352.8)
  1211| (146.8, 330.3)  | (146.8, 352.8)
  1212| (158.4, 330.3)  | (158.4, 352.8)
  1213| (169.9, 330.3)  | (169.9, 352.8)
  1214| (181.4, 330.3)  | (181.4, 352.8)
  1215| (192.9, 330.3)  | (192.9, 352.8)
  1216| (204.5, 330.3)  | (204.5, 352.8)
  1217| (216.0, 330.3)  | (216.0, 352.8)
  1218| (227.5, 330.3)  | (227.5, 352.8)
  1219| (239.1, 330.3)  | (239.1, 352.8)
  1220| (250.6, 330.3)  | (250.6, 352.8)
  1221| (262.1, 330.3)  | (262.1, 352.8)
  1222| (273.7, 330.3)  | (273.7, 352.8)
  1223| (285.2, 330.3)  | (285.2, 352.8)
  1224| (296.7, 330.3)  | (296.7, 352.8)
  1225| (308.2, 330.3)  | (308.2, 352.8)
  1226| (319.8, 330.3)  | (319.8, 352.8)
  1227| (331.3, 330.3)  | (331.3, 352.8)
  1228| (342.8, 330.3)  | (342.8, 352.8)
  1229| (354.4, 330.3)  | (354.4, 352.8)
  1230| (365.9, 330.3)  | (365.9, 352.8)
  1231| (377.4, 330.3)  | (377.4, 352.8)
  1232| (389.0, 330.3)  | (389.0, 352.8)
  1233| (400.5, 330.3)  | (400.5, 352.8)
  1234| (412.0, 330.3)  | (412.0, 352.8)
  1235| (423.5, 330.3)  | (423.5, 352.8)
  1236| (435.1, 330.3)  | (435.1, 352.8)
  1237| (446.6, 330.3)  | (446.6, 352.8)
  1238| (458.1, 330.3)  | (458.1, 352.8)
  1239| (469.7, 330.3)  | (469.7, 352.8)
  1240| (469.7, 341.1)  | (469.7, 363.6)
  1241| (458.1, 341.1)  | (458.1, 363.6)
  1242| (446.6, 341.1)  | (446.6, 363.6)
  1243| (435.1, 341.1)  | (435.1, 363.6)
  1244| (423.5, 341.1)  | (423.5, 363.6)
  1245| (412.0, 341.1)  | (412.0, 363.6)
  1246| (400.5, 341.1)  | (400.5, 363.6)
  1247| (389.0, 341.1)  | (389.0, 363.6)
  1248| (377.4, 341.1)  | (377.4, 363.6)
  1249| (365.9, 341.1)  | (365.9, 363.6)
  1250| (354.4, 341.1)  | (354.4, 363.6)
  1251| (342.8, 341.1)  | (342.8, 363.6)
  1252| (331.3, 341.1)  | (331.3, 363.6)
  1253| (319.8, 341.1)  | (319.8, 363.6)
  1254| (308.2, 341.1)  | (308.2, 363.6)
  1255| (296.7, 341.1)  | (296.7, 363.6)
  1256| (285.2, 341.1)  | (285.2, 363.6)
  1257| (273.7, 341.1)  | (273.7, 363.6)
  1258| (262.1, 341.1)  | (262.1, 363.6)
  1259| (250.6, 341.1)  | (250.6, 363.6)
  1260| (239.1, 341.1)  | (239.1, 363.6)
  1261| (227.5, 341.1)  | (227.5, 363.6)
  1262| (216.0, 341.1)  | (216.0, 363.6)
  1263| (204.5, 341.1)  | (204.5, 363.6)
  1264| (192.9, 341.1)  | (192.9, 363.6)
  1265| (181.4, 341.1)  | (181.4, 363.6)
  1266| (169.9, 341.1)  | (169.9, 363.6)
  1267| (158.4, 341.1)  | (158.4, 363.6)
  1268| (146.8, 341.1)  | (146.8, 363.6)
  1269| (135.3, 341.1)  | (135.3, 363.6)
  1270| (123.8, 341.1)  | (123.8, 363.6)
  1271| (112.2, 341.1)  | (112.2, 363.6)
  1272| (100.7, 341.1)  | (100.7, 363.6)
  1273| (89.2, 341.1)   | (89.2, 363.6)
  1274| (77.6, 341.1)   | (77.6, 363.6)
  1275| (66.1, 341.1)   | (66.1, 363.6)
  1276| (54.6, 341.1)   | (54.6, 363.6)
  1277| (43.1, 341.1)   | (43.1, 363.6)
  1278| (31.5, 341.1)   | (31.5, 363.6)
  1279| (20.0, 341.1)   | (20.0, 363.6)
  1280| (20.0, 351.8)   | (20.0, 374.3)
  1281| (31.5, 351.8)   | (31.5, 374.3)
  1282| (43.1, 351.8)   | (43.1, 374.3)
  1283| (54.6, 351.8)   | (54.6, 374.3)
  1284| (66.1, 351.8)   | (66.1, 374.3)
  1285| (77.7, 351.8)   | (77.7, 374.3)
  1286| (89.2, 351.8)   | (89.2, 374.3)
  1287| (100.7, 351.8)  | (100.7, 374.3)
  1288| (112.2, 351.8)  | (112.2, 374.3)
  1289| (123.8, 351.8)  | (123.8, 374.3)
  1290| (135.3, 351.8)  | (135.3, 374.3)
  1291| (146.8, 351.8)  | (146.8, 374.3)
  1292| (158.4, 351.8)  | (158.4, 374.3)
  1293| (169.9, 351.8)  | (169.9, 374.3)
  1294| (181.4, 351.8)  | (181.4, 374.3)
  1295| (192.9, 351.8)  | (192.9, 374.3)
  1296| (204.5, 351.8)  | (204.5, 374.3)
  1297| (216.0, 351.8)  | (216.0, 374.3)
  1298| (227.5, 351.8)  | (227.5, 374.3)
  1299| (239.1, 351.8)  | (239.1, 374.3)
  1300| (250.6, 351.8)  | (250.6, 374.3)
  1301| (262.1, 351.8)  | (262.1, 374.3)
  1302| (273.7, 351.8)  | (273.7, 374.3)
  1303| (285.2, 351.8)  | (285.2, 374.3)
  1304| (296.7, 351.8)  | (296.7, 374.3)
  1305| (308.2, 351.8)  | (308.2, 374.3)
  1306| (319.8, 351.8)  | (319.8, 374.3)
  1307| (331.3, 351.8)  | (331.3, 374.3)
  1308| (342.8, 351.8)  | (342.8, 374.3)
  1309| (354.4, 351.8)  | (354.4, 374.3)
  1310| (365.9, 351.8)  | (365.9, 374.3)
  1311| (377.4, 351.8)  | (377.4, 374.3)
  1312| (389.0, 351.8)  | (389.0, 374.3)
  1313| (400.5, 351.8)  | (400.5, 374.3)
  1314| (412.0, 351.8)  | (412.0, 374.3)
  1315| (423.5, 351.8)  | (423.5, 374.3)
  1316| (435.1, 351.8)  | (435.1, 374.3)
  1317| (446.6, 351.8)  | (446.6, 374.3)
  1318| (458.1, 351.8)  | (458.1, 374.3)
  1319| (469.7, 351.8)  | (469.7, 374.3)
  1320| (469.7, 362.6)  | (469.7, 385.1)
  1321| (458.1, 362.6)  | (458.1, 385.1)
  1322| (446.6, 362.6)  | (446.6, 385.1)
  1323| (435.1, 362.6)  | (435.1, 385.1)
  1324| (423.5, 362.6)  | (423.5, 385.1)
  1325| (412.0, 362.6)  | (412.0, 385.1)
  1326| (400.5, 362.6)  | (400.5, 385.1)
  1327| (389.0, 362.6)  | (389.0, 385.1)
  1328| (377.4, 362.6)  | (377.4, 385.1)
  1329| (365.9, 362.6)  | (365.9, 385.1)
  1330| (354.4, 362.6)  | (354.4, 385.1)
  1331| (342.8, 362.6)  | (342.8, 385.1)
  1332| (331.3, 362.6)  | (331.3, 385.1)
  1333| (319.8, 362.6)  | (319.8, 385.1)
  1334| (308.2, 362.6)  | (308.2, 385.1)
  1335| (296.7, 362.6)  | (296.7, 385.1)
  1336| (285.2, 362.6)  | (285.2, 385.1)
  1337| (273.7, 362.6)  | (273.7, 385.1)
  1338| (262.1, 362.6)  | (262.1, 385.1)
  1339| (250.6, 362.6)  | (250.6, 385.1)
  1340| (239.1, 362.6)  | (239.1, 385.1)
  1341| (227.5, 362.6)  | (227.5, 385.1)
  1342| (216.0, 362.6)  | (216.0, 385.1)
  1343| (204.5, 362.6)  | (204.5, 385.1)
  1344| (192.9, 362.6)  | (192.9, 385.1)
  1345| (181.4, 362.6)  | (181.4, 385.1)
  1346| (169.9, 362.6)  | (169.9, 385.1)
  1347| (158.4, 362.6)  | (158.4, 385.1)
  1348| (146.8, 362.6)  | (146.8, 385.1)
  1349| (135.3, 362.6)  | (135.3, 385.1)
  1350| (123.8, 362.6)  | (123.8, 385.1)
  1351| (112.2, 362.6)  | (112.2, 385.1)
  1352| (100.7, 362.6)  | (100.7, 385.1)
  1353| (89.2, 362.6)   | (89.2, 385.1)
  1354| (77.6, 362.6)   | (77.6, 385.1)
  1355| (66.1, 362.6)   | (66.1, 385.1)
  1356| (54.6, 362.6)   | (54.6, 385.1)
  1357| (43.1, 362.6)   | (43.1, 385.1)
  1358| (31.5, 362.6)   | (31.5, 385.1)
  1359| (20.0, 362.6)   | (20.0, 385.1)
  1360| (20.0, 373.3)   | (20.0, 395.8)
  1361| (31.5, 373.3)   | (31.5, 395.8)
  1362| (43.1, 373.3)   | (43.1, 395.8)
  1363| (54.6, 373.3)   | (54.6, 395.8)
  1364| (66.1, 373.3)   | (66.1, 395.8)
  1365| (77.7, 373.3)   | (77.7, 395.8)
  1366| (89.2, 373.3)   | (89.2, 395.8)
  1367| (100.7, 373.3)  | (100.7, 395.8)
  1368| (112.2, 373.3)  | (112.2, 395.8)
  1369| (123.8, 373.3)  | (123.8, 395.8)
  1370| (135.3, 373.3)  | (135.3, 395.8)
  1371| (146.8, 373.3)  | (146.8, 395.8)
  1372| (158.4, 373.3)  | (158.4, 395.8)
  1373| (169.9, 373.3)  | (169.9, 395.8)
  1374| (181.4, 373.3)  | (181.4, 395.8)
  1375| (192.9, 373.3)  | (192.9, 395.8)
  1376| (204.5, 373.3)  | (204.5, 395.8)
  1377| (216.0, 373.3)  | (216.0, 395.8)
  1378| (227.5, 373.3)  | (227.5, 395.8)
  1379| (239.1, 373.3)  | (239.1, 395.8)
  1380| (250.6, 373.3)  | (250.6, 395.8)
  1381| (262.1, 373.3)  | (262.1, 395.8)
  1382| (273.7, 373.3)  | (273.7, 395.8)
  1383| (285.2, 373.3)  | (285.2, 395.8)
  1384| (296.7, 373.3)  | (296.7, 395.8)
  1385| (308.2, 373.3)  | (308.2, 395.8)
  1386| (319.8, 373.3)  | (319.8, 395.8)
  1387| (331.3, 373.3)  | (331.3, 395.8)
  1388| (342.8, 373.3)  | (342.8, 395.8)
  1389| (354.4, 373.3)  | (354.4, 395.8)
  1390| (365.9, 373.3)  | (365.9, 395.8)
  1391| (377.4, 373.3)  | (377.4, 395.8)
  1392| (389.0, 373.3)  | (389.0, 395.8)
  1393| (400.5, 373.3)  | (400.5, 395.8)
  1394| (412.0, 373.3)  | (412.0, 395.8)
  1395| (423.5, 373.3)  | (423.5, 395.8)
  1396| (435.1, 373.3)  | (435.1, 395.8)
  1397| (446.6, 373.3)  | (446.6, 395.8)
  1398| (458.1, 373.3)  | (458.1, 395.8)
  1399| (469.7, 373.3)  | (469.7, 395.8)
  1400| (469.7, 384.1)  | (469.7, 406.6)
  1401| (458.1, 384.1)  | (458.1, 406.6)
  1402| (446.6, 384.1)  | (446.6, 406.6)
  1403| (435.1, 384.1)  | (435.1, 406.6)
  1404| (423.5, 384.1)  | (423.5, 406.6)
  1405| (412.0, 384.1)  | (412.0, 406.6)
  1406| (400.5, 384.1)  | (400.5, 406.6)
  1407| (389.0, 384.1)  | (389.0, 406.6)
  1408| (377.4, 384.1)  | (377.4, 406.6)
  1409| (365.9, 384.1)  | (365.9, 406.6)
  1410| (354.4, 384.1)  | (354.4, 406.6)
  1411| (342.8, 384.1)  | (342.8, 406.6)
  1412| (331.3, 384.1)  | (331.3, 406.6)
  1413| (319.8, 384.1)  | (319.8, 406.6)
  1414| (308.2, 384.1)  | (308.2, 406.6)
  1415| (296.7, 384.1)  | (296.7, 406.6)
  1416| (285.2, 384.1)  | (285.2, 406.6)
  1417| (273.7, 384.1)  | (273.7, 406.6)
  1418| (262.1, 384.1)  | (262.1, 406.6)
  1419| (250.6, 384.1)  | (250.6, 406.6)
  1420| (239.1, 384.1)  | (239.1, 406.6)
  1421| (227.5, 384.1)  | (227.5, 406.6)
  1422| (216.0, 384.1)  | (216.0, 406.6)
  1423| (204.5, 384.1)  | (204.5, 406.6)
  1424| (192.9, 384.1)  | (192.9, 406.6)
  1425| (181.4, 384.1)  | (181.4, 406.6)
  1426| (169.9, 384.1)  | (169.9, 406.6)
  1427| (158.4, 384.1)  | (158.4, 406.6)
  1428| (146.8, 384.1)  | (146.8, 406.6)
  1429| (135.3, 384.1)  | (135.3, 406.6)
  1430| (123.8, 384.1)  | (123.8, 406.6)
  1431| (112.2, 384.1)  | (112.2, 406.6)
  1432| (100.7, 384.1)  | (100.7, 406.6)
  1433| (89.2, 384.1)   | (89.2, 406.6)
  1434| (77.6, 384.1)   | (77.6, 406.6)
  1435| (66.1, 384.1)   | (66.1, 406.6)
  1436| (54.6, 384.1)   | (54.6, 406.6)
  1437| (43.1, 384.1)   | (43.1, 406.6)
  1438| (31.5, 384.1)   | (31.5, 406.6)
  1439| (20.0, 384.1)   | (20.0, 406.6)
  1440| (20.0, 394.9)   | (20.0, 417.4)
  1441| (31.5, 394.9)   | (31.5, 417.4)
  1442| (43.1, 394.9)   | (43.1, 417.4)
  1443| (54.6, 394.9)   | (54.6, 417.4)
  1444| (66.1, 394.9)   | (66.1, 417.4)
  1445| (77.7, 394.9)   | (77.7, 417.4)
  1446| (89.2, 394.9)   | (89.2, 417.4)
  1447| (100.7, 394.9)  | (100.7, 417.4)
  1448| (112.2, 394.9)  | (112.2, 417.4)
  1449| (123.8, 394.9)  | (123.8, 417.4)
  1450| (135.3, 394.9)  | (135.3, 417.4)
  1451| (146.8, 394.9)  | (146.8, 417.4)
  1452| (158.4, 394.9)  | (158.4, 417.4)
  1453| (169.9, 394.9)  | (169.9, 417.4)
  1454| (181.4, 394.9)  | (181.4, 417.4)
  1455| (192.9, 394.9)  | (192.9, 417.4)
  1456| (204.5, 394.9)  | (204.5, 417.4)
  1457| (216.0, 394.9)  | (216.0, 417.4)
  1458| (227.5, 394.9)  | (227.5, 417.4)
  1459| (239.1, 394.9)  | (239.1, 417.4)
  1460| (250.6, 394.9)  | (250.6, 417.4)
  1461| (262.1, 394.9)  | (262.1, 417.4)
  1462| (273.7, 394.9)  | (273.7, 417.4)
  1463| (285.2, 394.9)  | (285.2, 417.4)
  1464| (296.7, 394.9)  | (296.7, 417.4)
  1465| (308.2, 394.9)  | (308.2, 417.4)
  1466| (319.8, 394.9)  | (319.8, 417.4)
  1467| (331.3, 394.9)  | (331.3, 417.4)
  1468| (342.8, 394.9)  | (342.8, 417.4)
  1469| (354.4, 394.9)  | (354.4, 417.4)
  1470| (365.9, 394.9)  | (365.9, 417.4)
  1471| (377.4, 394.9)  | (377.4, 417.4)
  1472| (389.0, 394.9)  | (389.0, 417.4)
  1473| (400.5, 394.9)  | (400.5, 417.4)
  1474| (412.0, 394.9)  | (412.0, 417.4)
  1475| (423.5, 394.9)  | (423.5, 417.4)
  1476| (435.1, 394.9)  | (435.1, 417.4)
  1477| (446.6, 394.9)  | (446.6, 417.4)
  1478| (458.1, 394.9)  | (458.1, 417.4)
  1479| (469.7, 394.9)  | (469.7, 417.4)
  1480| (469.7, 405.6)  | (469.7, 428.1)
  1481| (458.1, 405.6)  | (458.1, 428.1)
  1482| (446.6, 405.6)  | (446.6, 428.1)
  1483| (435.1, 405.6)  | (435.1, 428.1)
  1484| (423.5, 405.6)  | (423.5, 428.1)
  1485| (412.0, 405.6)  | (412.0, 428.1)
  1486| (400.5, 405.6)  | (400.5, 428.1)
  1487| (389.0, 405.6)  | (389.0, 428.1)
  1488| (377.4, 405.6)  | (377.4, 428.1)
  1489| (365.9, 405.6)  | (365.9, 428.1)
  1490| (354.4, 405.6)  | (354.4, 428.1)
  1491| (342.8, 405.6)  | (342.8, 428.1)
  1492| (331.3, 405.6)  | (331.3, 428.1)
  1493| (319.8, 405.6)  | (319.8, 428.1)
  1494| (308.2, 405.6)  | (308.2, 428.1)
  1495| (296.7, 405.6)  | (296.7, 428.1)
  1496| (285.2, 405.6)  | (285.2, 428.1)
  1497| (273.7, 405.6)  | (273.7, 428.1)
  1498| (262.1, 405.6)  | (262.1, 428.1)
  1499| (250.6, 405.6)  | (250.6, 428.1)
  1500| (239.1, 405.6)  | (239.1, 428.1)
  1501| (227.5, 405.6)  | (227.5, 428.1)
  1502| (216.0, 405.6)  | (216.0, 428.1)
  1503| (204.5, 405.6)  | (204.5, 428.1)
  1504| (192.9, 405.6)  | (192.9, 428.1)
  1505| (181.4, 405.6)  | (181.4, 428.1)
  1506| (169.9, 405.6)  | (169.9, 428.1)
  1507| (158.4, 405.6)  | (158.4, 428.1)
  1508| (146.8, 405.6)  | (146.8, 428.1)
  1509| (135.3, 405.6)  | (135.3, 428.1)
  1510| (123.8, 405.6)  | (123.8, 428.1)
  1511| (112.2, 405.6)  | (112.2, 428.1)
  1512| (100.7, 405.6)  | (100.7, 428.1)
  1513| (89.2, 405.6)   | (89.2, 428.1)
  1514| (77.6, 405.6)   | (77.6, 428.1)
  1515| (66.1, 405.6)   | (66.1, 428.1)
  1516| (54.6, 405.6)   | (54.6, 428.1)
  1517| (43.1, 405.6)   | (43.1, 428.1)
  1518| (31.5, 405.6)   | (31.5, 428.1)
  1519| (20.0, 405.6)   | (20.0, 428.1)
  1520| (20.0, 416.4)   | (20.0, 438.9)
  1521| (31.5, 416.4)   | (31.5, 438.9)
  1522| (43.1, 416.4)   | (43.1, 438.9)
  1523| (54.6, 416.4)   | (54.6, 438.9)
  1524| (66.1, 416.4)   | (66.1, 438.9)
  1525| (77.7, 416.4)   | (77.7, 438.9)
  1526| (89.2, 416.4)   | (89.2, 438.9)
  1527| (100.7, 416.4)  | (100.7, 438.9)
  1528| (112.2, 416.4)  | (112.2, 438.9)
  1529| (123.8, 416.4)  | (123.8, 438.9)
  1530| (135.3, 416.4)  | (135.3, 438.9)
  1531| (146.8, 416.4)  | (146.8, 438.9)
  1532| (158.4, 416.4)  | (158.4, 438.9)
  1533| (169.9, 416.4)  | (169.9, 438.9)
  1534| (181.4, 416.4)  | (181.4, 438.9)
  1535| (192.9, 416.4)  | (192.9, 438.9)
  1536| (204.5, 416.4)  | (204.5, 438.9)
  1537| (216.0, 416.4)  | (216.0, 438.9)
  1538| (227.5, 416.4)  | (227.5, 438.9)
  1539| (239.1, 416.4)  | (239.1, 438.9)
  1540| (250.6, 416.4)  | (250.6, 438.9)
  1541| (262.1, 416.4)  | (262.1, 438.9)
  1542| (273.7, 416.4)  | (273.7, 438.9)
  1543| (285.2, 416.4)  | (285.2, 438.9)
  1544| (296.7, 416.4)  | (296.7, 438.9)
  1545| (308.2, 416.4)  | (308.2, 438.9)
  1546| (319.8, 416.4)  | (319.8, 438.9)
  1547| (331.3, 416.4)  | (331.3, 438.9)
  1548| (342.8, 416.4)  | (342.8, 438.9)
  1549| (354.4, 416.4)  | (354.4, 438.9)
  1550| (365.9, 416.4)  | (365.9, 438.9)
  1551| (377.4, 416.4)  | (377.4, 438.9)
  1552| (389.0, 416.4)  | (389.0, 438.9)
  1553| (400.5, 416.4)  | (400.5, 438.9)
  1554| (412.0, 416.4)  | (412.0, 438.9)
  1555| (423.5, 416.4)  | (423.5, 438.9)
  1556| (435.1, 416.4)  | (435.1, 438.9)
  1557| (446.6, 416.4)  | (446.6, 438.9)
  1558| (458.1, 416.4)  | (458.1, 438.9)
  1559| (469.7, 416.4)  | (469.7, 438.9)
  1560| (469.7, 427.1)  | (469.7, 449.6)
  1561| (458.1, 427.1)  | (458.1, 449.6)
  1562| (446.6, 427.1)  | (446.6, 449.6)
  1563| (435.1, 427.1)  | (435.1, 449.6)
  1564| (423.5, 427.1)  | (423.5, 449.6)
  1565| (412.0, 427.1)  | (412.0, 449.6)
  1566| (400.5, 427.1)  | (400.5, 449.6)
  1567| (389.0, 427.1)  | (389.0, 449.6)
  1568| (377.4, 427.1)  | (377.4, 449.6)
  1569| (365.9, 427.1)  | (365.9, 449.6)
  1570| (354.4, 427.1)  | (354.4, 449.6)
  1571| (342.8, 427.1)  | (342.8, 449.6)
  1572| (331.3, 427.1)  | (331.3, 449.6)
  1573| (319.8, 427.1)  | (319.8, 449.6)
  1574| (308.2, 427.1)  | (308.2, 449.6)
  1575| (296.7, 427.1)  | (296.7, 449.6)
  1576| (285.2, 427.1)  | (285.2, 449.6)
  1577| (273.7, 427.1)  | (273.7, 449.6)
  1578| (262.1, 427.1)  | (262.1, 449.6)
  1579| (250.6, 427.1)  | (250.6, 449.6)
  1580| (239.1, 427.1)  | (239.1, 449.6)
  1581| (227.5, 427.1)  | (227.5, 449.6)
  1582| (216.0, 427.1)  | (216.0, 449.6)
  1583| (204.5, 427.1)  | (204.5, 449.6)
  1584| (192.9, 427.1)  | (192.9, 449.6)
  1585| (181.4, 427.1)  | (181.4, 449.6)
  1586| (169.9, 427.1)  | (169.9, 449.6)
  1587| (158.4, 427.1)  | (158.4, 449.6)
  1588| (146.8, 427.1)  | (146.8, 449.6)
  1589| (135.3, 427.1)  | (135.3, 449.6)
  1590| (123.8, 427.1)  | (123.8, 449.6)
  1591| (112.2, 427.1)  | (112.2, 449.6)
  1592| (100.7, 427.1)  | (100.7, 449.6)
  1593| (89.2, 427.1)   | (89.2, 449.6)
  1594| (77.6, 427.1)   | (77.6, 449.6)
  1595| (66.1, 427.1)   | (66.1, 449.6)
  1596| (54.6, 427.1)   | (54.6, 449.6)
  1597| (43.1, 427.1)   | (43.1, 449.6)
  1598| (31.5, 427.1)   | (31.5, 449.6)
  1599| (20.0, 427.1)   | (20.0, 449.6)
beacon: loaded fnorm=5103294.57 temp=22.71 amfg=0.968 from nvm
beacon: built tempco model version 1 {'amfg': 0.9678539038888552, 'tcc': -6.5799530974975735e-06, 'tcfl': -0.0006423089102843345, 'tctl': 0.0019707581405379064, 'fmin': 5103294.566273689, 'fmin_temp': 22.714570999145508}
Enabling Beacon accelerometer
Selected Beacon accelerometer scale 16g
Sending MCU 'beacon' printer configuration...
Configured MCU 'beacon' (0 moves)
Starting heater checks for extruder
Write g-code response
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/gcode.py", line 459, in _respond_raw
    os.write(self.fd, (msg+"\n").encode())
BlockingIOError: [Errno 11] Resource temporarily unavailable
Stats 70941.3: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4045 bytes_read=8700 bytes_retransmit=9 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999985 rpi: mcu_awake=0.003 mcu_task_avg=0.000020 mcu_task_stddev=0.000011 bytes_write=876 bytes_read=4775 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004518 adj=49994468 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000021 mcu_task_stddev=0.000020 bytes_write=1476 bytes_read=4908 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999321 adj=63999044 Octopus_V1.1_F446: temp=0.0 EBB42_v1.2_T0: temp=0.0 raspberry_pi: temp=36.0  heater_bed: target=0 temp=0.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=380 bytes_read=2104 bytes_retransmit=0 bytes_invalid=0 send_seq=62 receive_seq=62 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999395 adj=31998231 coil_temp=0.0 refs=0 sysload=0.52 cputime=3420.324 memavail=1403860 print_time=12.146 buffer_time=0.248 print_stall=0 extruder: target=0 temp=0.0 pwm=0.000
webhooks: registering remote method 'shutdown_machine' for connection id: 4124998528
webhooks: registering remote method 'reboot_machine' for connection id: 4124998528
webhooks: registering remote method 'pause_job_queue' for connection id: 4124998528
webhooks: registering remote method 'start_job_queue' for connection id: 4124998528
Stats 70942.3: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4051 bytes_read=8803 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999790 rpi: mcu_awake=0.003 mcu_task_avg=0.000020 mcu_task_stddev=0.000011 bytes_write=882 bytes_read=4791 bytes_retransmit=0 bytes_invalid=0 send_seq=121 receive_seq=121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004634 adj=50024407 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000021 mcu_task_stddev=0.000020 bytes_write=1490 bytes_read=5026 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999336 adj=63999834 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=35.0  heater_bed: target=0 temp=52.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=386 bytes_read=2460 bytes_retransmit=0 bytes_invalid=0 send_seq=63 receive_seq=63 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000017 adj=32000038 coil_temp=35.0 refs=0 mcu_temp=32.23 supply_voltage=3.014 sysload=0.52 cputime=3420.389 memavail=1399112 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=160.3 pwm=0.000
Stats 70943.8: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4063 bytes_read=8980 bytes_retransmit=9 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999629 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000017 bytes_write=888 bytes_read=4820 bytes_retransmit=0 bytes_invalid=0 send_seq=122 receive_seq=122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004750 adj=50021172 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000018 mcu_task_stddev=0.000030 bytes_write=1517 bytes_read=5223 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999523 adj=64000002 Octopus_V1.1_F446: temp=33.3 EBB42_v1.2_T0: temp=33.9 raspberry_pi: temp=36.0  heater_bed: target=0 temp=52.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=392 bytes_read=2986 bytes_retransmit=0 bytes_invalid=0 send_seq=64 receive_seq=64 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999634 adj=32001023 coil_temp=35.0 refs=0 mcu_temp=32.13 supply_voltage=3.014 sysload=0.52 cputime=3420.444 memavail=1405948 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=158.6 pwm=0.000
Stats 70944.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=4069 bytes_read=9098 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999547 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000017 bytes_write=894 bytes_read=4836 bytes_retransmit=0 bytes_invalid=0 send_seq=123 receive_seq=123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004930 adj=50015517 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000018 mcu_task_stddev=0.000030 bytes_write=1523 bytes_read=5355 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999458 adj=64000594 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=36.0  heater_bed: target=0 temp=52.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=398 bytes_read=3342 bytes_retransmit=0 bytes_invalid=0 send_seq=65 receive_seq=65 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999562 adj=32000006 coil_temp=35.0 refs=0 mcu_temp=32.09 supply_voltage=3.014 sysload=0.48 cputime=3420.470 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=156.9 pwm=0.000
Stats 70945.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=4075 bytes_read=9215 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999629 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000017 bytes_write=906 bytes_read=4868 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005308 adj=50013590 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000018 mcu_task_stddev=0.000030 bytes_write=1529 bytes_read=5458 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999467 adj=64000240 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=36.5  heater_bed: target=0 temp=52.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=404 bytes_read=3698 bytes_retransmit=0 bytes_invalid=0 send_seq=66 receive_seq=66 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999704 adj=31999824 coil_temp=35.0 refs=0 mcu_temp=32.05 supply_voltage=3.014 sysload=0.48 cputime=3420.505 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=155.5 pwm=0.000
Stats 70946.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=4081 bytes_read=9333 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999670 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000017 bytes_write=912 bytes_read=4884 bytes_retransmit=0 bytes_invalid=0 send_seq=126 receive_seq=126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005483 adj=50012820 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000018 mcu_task_stddev=0.000030 bytes_write=1535 bytes_read=5561 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999472 adj=64000003 Octopus_V1.1_F446: temp=33.0 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=36.5  heater_bed: target=0 temp=52.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=410 bytes_read=4054 bytes_retransmit=0 bytes_invalid=0 send_seq=67 receive_seq=67 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999684 adj=32000069 coil_temp=35.0 refs=0 mcu_temp=32.03 supply_voltage=3.014 sysload=0.48 cputime=3420.560 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=154.1 pwm=0.000
Stats 70947.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=4087 bytes_read=9436 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999695 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000017 bytes_write=918 bytes_read=4900 bytes_retransmit=0 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005639 adj=50011627 toolboard_t0: mcu_awake=0.006 mcu_task_avg=0.000018 mcu_task_stddev=0.000030 bytes_write=1541 bytes_read=5693 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999482 adj=63999861 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=34.6  heater_bed: target=0 temp=52.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=416 bytes_read=4410 bytes_retransmit=0 bytes_invalid=0 send_seq=68 receive_seq=68 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999909 coil_temp=35.0 refs=0 mcu_temp=32.02 supply_voltage=3.014 sysload=0.48 cputime=3420.616 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=152.6 pwm=0.000
Stats 70948.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=4093 bytes_read=9553 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999821 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=924 bytes_read=4929 bytes_retransmit=0 bytes_invalid=0 send_seq=128 receive_seq=128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005748 adj=50010746 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1547 bytes_read=5810 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999470 adj=63999793 Octopus_V1.1_F446: temp=33.1 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=34.6  heater_bed: target=0 temp=52.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=422 bytes_read=4766 bytes_retransmit=0 bytes_invalid=0 send_seq=69 receive_seq=69 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999737 adj=31999887 coil_temp=35.0 refs=0 mcu_temp=32.03 supply_voltage=3.014 sysload=0.48 cputime=3420.670 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=151.5 pwm=0.000
Stats 70949.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4099 bytes_read=9685 bytes_retransmit=9 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999780 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=930 bytes_read=4945 bytes_retransmit=0 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005875 adj=50009813 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1553 bytes_read=5913 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999463 adj=63999486 Octopus_V1.1_F446: temp=33.2 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=35.0  heater_bed: target=0 temp=52.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=428 bytes_read=5122 bytes_retransmit=0 bytes_invalid=0 send_seq=70 receive_seq=70 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999737 adj=31999876 coil_temp=35.0 refs=0 mcu_temp=32.06 supply_voltage=3.014 sysload=0.44 cputime=3420.725 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=150.4 pwm=0.000
Stats 70950.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4105 bytes_read=9788 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999748 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=936 bytes_read=4961 bytes_retransmit=0 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005990 adj=50009461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1559 bytes_read=6045 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999460 adj=63999538 Octopus_V1.1_F446: temp=33.0 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=34.6  heater_bed: target=0 temp=52.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=434 bytes_read=5478 bytes_retransmit=0 bytes_invalid=0 send_seq=71 receive_seq=71 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999748 adj=31999884 coil_temp=35.0 refs=0 mcu_temp=32.09 supply_voltage=3.014 sysload=0.44 cputime=3420.782 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=148.9 pwm=0.000
Stats 70951.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4111 bytes_read=9920 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999730 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=942 bytes_read=4977 bytes_retransmit=0 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006089 adj=50009184 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1565 bytes_read=6148 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999452 adj=63999580 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=52.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=440 bytes_read=5834 bytes_retransmit=0 bytes_invalid=0 send_seq=72 receive_seq=72 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999739 adj=31999925 coil_temp=35.0 refs=0 mcu_temp=32.11 supply_voltage=3.014 sysload=0.44 cputime=3420.836 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=148.0 pwm=0.000
Stats 70952.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4117 bytes_read=10021 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999726 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000018 bytes_write=948 bytes_read=4993 bytes_retransmit=0 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006189 adj=50008928 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1571 bytes_read=6251 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999494 adj=63999568 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=34.6  heater_bed: target=0 temp=52.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=446 bytes_read=6190 bytes_retransmit=0 bytes_invalid=0 send_seq=73 receive_seq=73 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999728 adj=31999872 coil_temp=35.0 refs=0 mcu_temp=32.14 supply_voltage=3.014 sysload=0.44 cputime=3420.890 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=147.0 pwm=0.000
Stats 70953.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4123 bytes_read=10117 bytes_retransmit=9 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999728 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=954 bytes_read=5022 bytes_retransmit=0 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006297 adj=50008772 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1577 bytes_read=6397 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999487 adj=63999786 Octopus_V1.1_F446: temp=32.9 EBB42_v1.2_T0: temp=34.0 raspberry_pi: temp=35.0  heater_bed: target=0 temp=52.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452 bytes_read=6546 bytes_retransmit=0 bytes_invalid=0 send_seq=74 receive_seq=74 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999719 adj=31999811 coil_temp=35.0 refs=0 mcu_temp=32.19 supply_voltage=3.014 sysload=0.44 cputime=3420.945 memavail=1406120 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=145.7 pwm=0.000
Stats 70954.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4129 bytes_read=10261 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999715 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=960 bytes_read=5038 bytes_retransmit=0 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006402 adj=50008734 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1583 bytes_read=6500 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999484 adj=63999699 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=458 bytes_read=6902 bytes_retransmit=0 bytes_invalid=0 send_seq=75 receive_seq=75 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999705 adj=31999763 coil_temp=35.1 refs=0 mcu_temp=32.23 supply_voltage=3.014 sysload=0.40 cputime=3421.000 memavail=1405868 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=144.3 pwm=0.000
Stats 70955.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4135 bytes_read=10364 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999702 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=966 bytes_read=5054 bytes_retransmit=0 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006491 adj=50008762 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1589 bytes_read=6603 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999477 adj=63999678 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=34.1  heater_bed: target=0 temp=51.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=464 bytes_read=7258 bytes_retransmit=0 bytes_invalid=0 send_seq=76 receive_seq=76 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999696 adj=31999718 coil_temp=35.1 refs=0 mcu_temp=32.29 supply_voltage=3.014 sysload=0.40 cputime=3421.053 memavail=1405868 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=143.6 pwm=0.000
Stats 70956.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4141 bytes_read=10467 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999702 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=972 bytes_read=5070 bytes_retransmit=0 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006598 adj=50008734 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1595 bytes_read=6735 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999471 adj=63999640 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=51.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=470 bytes_read=7614 bytes_retransmit=0 bytes_invalid=0 send_seq=77 receive_seq=77 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999706 adj=31999698 coil_temp=35.1 refs=0 mcu_temp=32.32 supply_voltage=3.014 sysload=0.40 cputime=3421.107 memavail=1405868 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=142.2 pwm=0.000
Stats 70957.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4147 bytes_read=10599 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999720 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=978 bytes_read=5086 bytes_retransmit=0 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006720 adj=50008840 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1601 bytes_read=6838 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999465 adj=63999589 Octopus_V1.1_F446: temp=32.8 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=51.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=476 bytes_read=7970 bytes_retransmit=0 bytes_invalid=0 send_seq=78 receive_seq=78 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999698 adj=31999757 coil_temp=35.1 refs=0 mcu_temp=32.36 supply_voltage=3.014 sysload=0.40 cputime=3421.162 memavail=1404864 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=141.4 pwm=0.000
Stats 70958.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4153 bytes_read=10702 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999783 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=984 bytes_read=5115 bytes_retransmit=0 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006837 adj=50009026 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1607 bytes_read=6955 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999460 adj=63999513 Octopus_V1.1_F446: temp=32.6 EBB42_v1.2_T0: temp=34.2 raspberry_pi: temp=34.1  heater_bed: target=0 temp=51.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=482 bytes_read=8326 bytes_retransmit=0 bytes_invalid=0 send_seq=79 receive_seq=79 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999698 adj=31999700 coil_temp=35.1 refs=0 mcu_temp=32.41 supply_voltage=3.014 sysload=0.40 cputime=3421.215 memavail=1404868 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=140.4 pwm=0.000
Stats 70959.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4159 bytes_read=10819 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999749 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=990 bytes_read=5131 bytes_retransmit=0 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006894 adj=50009105 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1613 bytes_read=7087 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999451 adj=63999348 Octopus_V1.1_F446: temp=32.6 EBB42_v1.2_T0: temp=34.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=51.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=488 bytes_read=8682 bytes_retransmit=0 bytes_invalid=0 send_seq=80 receive_seq=80 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999707 adj=31999640 coil_temp=35.2 refs=0 mcu_temp=32.46 supply_voltage=3.014 sysload=0.37 cputime=3421.263 memavail=1397256 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=139.4 pwm=0.000
Stats 70960.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4165 bytes_read=10951 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999699 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=996 bytes_read=5147 bytes_retransmit=0 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006952 adj=50008990 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1619 bytes_read=7190 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999415 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=51.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=494 bytes_read=9038 bytes_retransmit=0 bytes_invalid=0 send_seq=81 receive_seq=81 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999697 adj=31999750 coil_temp=35.2 refs=0 mcu_temp=32.51 supply_voltage=3.014 sysload=0.37 cputime=3421.287 memavail=1402864 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=138.2 pwm=0.000
Stats 70961.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4171 bytes_read=11054 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999657 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1002 bytes_read=5163 bytes_retransmit=0 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007013 adj=50008976 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1625 bytes_read=7293 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999427 adj=63999485 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=35.0  heater_bed: target=0 temp=51.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=500 bytes_read=9394 bytes_retransmit=0 bytes_invalid=0 send_seq=82 receive_seq=82 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999686 adj=31999756 coil_temp=35.2 refs=0 mcu_temp=32.56 supply_voltage=3.014 sysload=0.37 cputime=3421.310 memavail=1402864 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=137.4 pwm=0.000
Stats 70962.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4177 bytes_read=11157 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999619 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1008 bytes_read=5179 bytes_retransmit=0 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007082 adj=50008994 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1631 bytes_read=7425 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999417 adj=63999530 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=506 bytes_read=9750 bytes_retransmit=0 bytes_invalid=0 send_seq=83 receive_seq=83 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999677 adj=31999747 coil_temp=35.2 refs=0 mcu_temp=32.63 supply_voltage=3.014 sysload=0.37 cputime=3421.333 memavail=1403116 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=136.2 pwm=0.000
Stats 70963.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4183 bytes_read=11289 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999589 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000019 bytes_write=1014 bytes_read=5208 bytes_retransmit=0 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007152 adj=50009094 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1637 bytes_read=7542 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999410 adj=63999563 Octopus_V1.1_F446: temp=32.6 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=35.0  heater_bed: target=0 temp=51.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=512 bytes_read=10106 bytes_retransmit=0 bytes_invalid=0 send_seq=84 receive_seq=84 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999669 adj=31999741 coil_temp=35.2 refs=0 mcu_temp=32.68 supply_voltage=3.014 sysload=0.37 cputime=3421.357 memavail=1402892 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=135.3 pwm=0.000
Stats 70964.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4189 bytes_read=11406 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999621 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000019 bytes_write=1020 bytes_read=5224 bytes_retransmit=0 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007248 adj=50009189 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1643 bytes_read=7645 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999403 adj=63999585 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=518 bytes_read=10462 bytes_retransmit=0 bytes_invalid=0 send_seq=85 receive_seq=85 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999664 adj=31999731 coil_temp=35.3 refs=0 mcu_temp=32.73 supply_voltage=3.014 sysload=0.34 cputime=3421.402 memavail=1403892 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=134.4 pwm=0.000
Stats 70965.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4195 bytes_read=11509 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999612 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000019 bytes_write=1026 bytes_read=5240 bytes_retransmit=0 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007356 adj=50009351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1649 bytes_read=7777 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999403 adj=63999439 Octopus_V1.1_F446: temp=32.5 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=524 bytes_read=10818 bytes_retransmit=0 bytes_invalid=0 send_seq=86 receive_seq=86 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999664 adj=31999659 coil_temp=35.3 refs=0 mcu_temp=32.77 supply_voltage=3.014 sysload=0.34 cputime=3421.458 memavail=1403988 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=133.2 pwm=0.000
Stats 70966.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4201 bytes_read=11641 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999625 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000019 bytes_write=1032 bytes_read=5256 bytes_retransmit=0 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007443 adj=50009697 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1655 bytes_read=7880 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999405 adj=63999489 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=51.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=536 bytes_read=11190 bytes_retransmit=0 bytes_invalid=0 send_seq=88 receive_seq=88 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999661 adj=31999690 coil_temp=35.3 refs=0 mcu_temp=32.81 supply_voltage=3.014 sysload=0.34 cputime=3421.514 memavail=1403540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=132.4 pwm=0.000
Stats 70967.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4207 bytes_read=11744 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999611 rpi: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000019 bytes_write=1038 bytes_read=5272 bytes_retransmit=0 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007525 adj=50009788 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1661 bytes_read=7983 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999405 adj=63999482 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=35.0  heater_bed: target=0 temp=51.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=542 bytes_read=11546 bytes_retransmit=0 bytes_invalid=0 send_seq=89 receive_seq=89 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999659 coil_temp=35.3 refs=0 mcu_temp=32.87 supply_voltage=3.014 sysload=0.34 cputime=3421.565 memavail=1403292 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=131.9 pwm=0.000
Stats 70968.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4213 bytes_read=11847 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000019 bytes_write=1044 bytes_read=5301 bytes_retransmit=0 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007610 adj=50009907 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=1667 bytes_read=8129 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999542 Octopus_V1.1_F446: temp=32.1 EBB42_v1.2_T0: temp=34.3 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=548 bytes_read=11902 bytes_retransmit=0 bytes_invalid=0 send_seq=90 receive_seq=90 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999707 coil_temp=35.4 refs=0 mcu_temp=32.91 supply_voltage=3.014 sysload=0.34 cputime=3421.618 memavail=1402788 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=130.8 pwm=0.000
Stats 70969.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4219 bytes_read=11993 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999600 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000019 bytes_write=1050 bytes_read=5317 bytes_retransmit=0 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007711 adj=50010030 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=1673 bytes_read=8232 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999580 Octopus_V1.1_F446: temp=32.3 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.6  heater_bed: target=0 temp=51.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=554 bytes_read=12258 bytes_retransmit=0 bytes_invalid=0 send_seq=91 receive_seq=91 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999715 coil_temp=35.4 refs=0 mcu_temp=32.99 supply_voltage=3.014 sysload=0.31 cputime=3421.674 memavail=1402792 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=129.8 pwm=0.000
Stats 70970.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4225 bytes_read=12096 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999610 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000019 bytes_write=1056 bytes_read=5333 bytes_retransmit=0 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007794 adj=50010311 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=1679 bytes_read=8335 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999412 adj=63999592 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=35.0  heater_bed: target=0 temp=51.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=560 bytes_read=12614 bytes_retransmit=0 bytes_invalid=0 send_seq=92 receive_seq=92 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999661 adj=31999727 coil_temp=35.4 refs=0 mcu_temp=33.04 supply_voltage=3.014 sysload=0.31 cputime=3421.729 memavail=1402792 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=129.3 pwm=0.000
Stats 70971.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4231 bytes_read=12199 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999619 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000019 bytes_write=1062 bytes_read=5349 bytes_retransmit=0 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007878 adj=50010362 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=1685 bytes_read=8467 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999578 Octopus_V1.1_F446: temp=32.2 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=35.0  heater_bed: target=0 temp=51.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=566 bytes_read=12970 bytes_retransmit=0 bytes_invalid=0 send_seq=93 receive_seq=93 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999665 adj=31999712 coil_temp=35.4 refs=0 mcu_temp=33.08 supply_voltage=3.014 sysload=0.31 cputime=3421.785 memavail=1402792 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=128.1 pwm=0.000
Stats 70972.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4237 bytes_read=12331 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999620 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000019 bytes_write=1068 bytes_read=5365 bytes_retransmit=0 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007968 adj=50010446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=1691 bytes_read=8570 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999562 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=34.4 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=572 bytes_read=13326 bytes_retransmit=0 bytes_invalid=0 send_seq=94 receive_seq=94 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999734 coil_temp=35.4 refs=0 mcu_temp=33.12 supply_voltage=3.014 sysload=0.31 cputime=3421.840 memavail=1402792 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=127.2 pwm=0.000
Stats 70973.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4243 bytes_read=12434 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999616 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1074 bytes_read=5394 bytes_retransmit=0 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008058 adj=50010612 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1697 bytes_read=8687 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999440 adj=63999624 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=578 bytes_read=13682 bytes_retransmit=0 bytes_invalid=0 send_seq=95 receive_seq=95 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999662 adj=31999709 coil_temp=35.5 refs=0 mcu_temp=33.17 supply_voltage=3.014 sysload=0.31 cputime=3421.896 memavail=1402792 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=126.6 pwm=0.000
Stats 70974.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4249 bytes_read=12551 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1080 bytes_read=5410 bytes_retransmit=0 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008136 adj=50010779 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1703 bytes_read=8819 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999438 adj=63999778 Octopus_V1.1_F446: temp=32.0 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=33.6  heater_bed: target=0 temp=50.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=584 bytes_read=14038 bytes_retransmit=0 bytes_invalid=0 send_seq=96 receive_seq=96 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999665 adj=31999722 coil_temp=35.5 refs=0 mcu_temp=33.22 supply_voltage=3.014 sysload=0.29 cputime=3421.952 memavail=1401796 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=125.4 pwm=0.000
Stats 70975.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4255 bytes_read=12683 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999636 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1086 bytes_read=5426 bytes_retransmit=0 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008214 adj=50010745 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1709 bytes_read=8922 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999435 adj=63999607 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=590 bytes_read=14394 bytes_retransmit=0 bytes_invalid=0 send_seq=97 receive_seq=97 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999665 adj=31999693 coil_temp=35.5 refs=0 mcu_temp=33.26 supply_voltage=3.014 sysload=0.29 cputime=3422.006 memavail=1401808 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=124.7 pwm=0.000
Stats 70976.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4261 bytes_read=12784 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999622 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1092 bytes_read=5442 bytes_retransmit=0 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008291 adj=50010864 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1715 bytes_read=9025 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999450 adj=63999605 Octopus_V1.1_F446: temp=31.9 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=34.1  heater_bed: target=0 temp=50.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=596 bytes_read=14750 bytes_retransmit=0 bytes_invalid=0 send_seq=98 receive_seq=98 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999660 adj=31999718 coil_temp=35.5 refs=0 mcu_temp=33.33 supply_voltage=3.014 sysload=0.29 cputime=3422.058 memavail=1396264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=124.1 pwm=0.000
Stats 70977.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4267 bytes_read=12880 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999599 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1098 bytes_read=5458 bytes_retransmit=0 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008354 adj=50010975 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1721 bytes_read=9157 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999442 adj=63999781 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=602 bytes_read=15106 bytes_retransmit=0 bytes_invalid=0 send_seq=99 receive_seq=99 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999657 adj=31999707 coil_temp=35.6 refs=0 mcu_temp=33.36 supply_voltage=3.014 sysload=0.29 cputime=3422.082 memavail=1401816 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=122.8 pwm=0.000
Stats 70978.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4273 bytes_read=13010 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999581 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=1104 bytes_read=5487 bytes_retransmit=0 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008419 adj=50010982 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1727 bytes_read=9274 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999433 adj=63999734 Octopus_V1.1_F446: temp=31.8 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=50.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=608 bytes_read=15462 bytes_retransmit=0 bytes_invalid=0 send_seq=100 receive_seq=100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999657 adj=31999721 coil_temp=35.6 refs=0 mcu_temp=33.41 supply_voltage=3.014 sysload=0.29 cputime=3422.105 memavail=1401816 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=122.2 pwm=0.000
Stats 70979.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4279 bytes_read=13113 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999569 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=1110 bytes_read=5503 bytes_retransmit=0 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008484 adj=50011020 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1733 bytes_read=9377 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999426 adj=63999678 Octopus_V1.1_F446: temp=31.7 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=35.0  heater_bed: target=0 temp=50.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=614 bytes_read=15818 bytes_retransmit=0 bytes_invalid=0 send_seq=101 receive_seq=101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999651 adj=31999755 coil_temp=35.6 refs=0 mcu_temp=33.46 supply_voltage=3.014 sysload=0.26 cputime=3422.128 memavail=1401816 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=121.4 pwm=0.000
Stats 70980.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4285 bytes_read=13230 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999553 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=1116 bytes_read=5519 bytes_retransmit=0 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008556 adj=50011067 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1739 bytes_read=9509 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999420 adj=63999627 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=620 bytes_read=16174 bytes_retransmit=0 bytes_invalid=0 send_seq=102 receive_seq=102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999648 adj=31999723 coil_temp=35.6 refs=0 mcu_temp=33.49 supply_voltage=3.014 sysload=0.26 cputime=3422.152 memavail=1404412 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=120.6 pwm=0.000
Stats 70981.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4291 bytes_read=13362 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999535 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=1122 bytes_read=5535 bytes_retransmit=0 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008622 adj=50011199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1745 bytes_read=9612 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999611 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=626 bytes_read=16530 bytes_retransmit=0 bytes_invalid=0 send_seq=103 receive_seq=103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999645 adj=31999727 coil_temp=35.6 refs=0 mcu_temp=33.53 supply_voltage=3.014 sysload=0.26 cputime=3422.176 memavail=1404436 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=119.9 pwm=0.000
Stats 70982.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4297 bytes_read=13465 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999543 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000018 bytes_write=1128 bytes_read=5551 bytes_retransmit=0 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008704 adj=50011272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1751 bytes_read=9715 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999612 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=50.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=632 bytes_read=16886 bytes_retransmit=0 bytes_invalid=0 send_seq=104 receive_seq=104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999645 adj=31999724 coil_temp=35.7 refs=0 mcu_temp=33.57 supply_voltage=3.014 sysload=0.26 cputime=3422.230 memavail=1404212 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=119.2 pwm=0.000
Stats 70983.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4303 bytes_read=13568 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999545 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=1134 bytes_read=5580 bytes_retransmit=0 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008784 adj=50011445 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1757 bytes_read=9861 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999576 Octopus_V1.1_F446: temp=31.3 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.1  heater_bed: target=0 temp=50.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=638 bytes_read=17242 bytes_retransmit=0 bytes_invalid=0 send_seq=105 receive_seq=105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999645 adj=31999716 coil_temp=35.7 refs=0 mcu_temp=33.61 supply_voltage=3.014 sysload=0.26 cputime=3422.285 memavail=1404212 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=118.3 pwm=0.000
Stats 70984.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4309 bytes_read=13700 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999582 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=1140 bytes_read=5596 bytes_retransmit=0 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008863 adj=50011600 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1763 bytes_read=9964 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999565 Octopus_V1.1_F446: temp=31.6 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=644 bytes_read=17598 bytes_retransmit=0 bytes_invalid=0 send_seq=106 receive_seq=106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999646 adj=31999715 coil_temp=35.7 refs=0 mcu_temp=33.65 supply_voltage=3.014 sysload=0.24 cputime=3422.337 memavail=1403960 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=117.5 pwm=0.000
Stats 70985.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4315 bytes_read=13817 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999587 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=1146 bytes_read=5612 bytes_retransmit=0 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008942 adj=50011636 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1769 bytes_read=10067 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999423 adj=63999515 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=35.0  heater_bed: target=0 temp=50.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=650 bytes_read=17972 bytes_retransmit=0 bytes_invalid=0 send_seq=107 receive_seq=107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999645 adj=31999656 coil_temp=35.7 refs=0 mcu_temp=33.69 supply_voltage=3.014 sysload=0.24 cputime=3422.394 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=116.9 pwm=0.000
Stats 70986.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4321 bytes_read=13920 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999582 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=1152 bytes_read=5628 bytes_retransmit=0 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009022 adj=50011780 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1775 bytes_read=10199 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999525 Octopus_V1.1_F446: temp=31.5 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=35.0  heater_bed: target=0 temp=50.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=656 bytes_read=18328 bytes_retransmit=0 bytes_invalid=0 send_seq=108 receive_seq=108 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999643 adj=31999654 coil_temp=35.8 refs=0 mcu_temp=33.73 supply_voltage=3.014 sysload=0.24 cputime=3422.448 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=115.9 pwm=0.000
Stats 70987.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4327 bytes_read=14052 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999577 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000018 bytes_write=1158 bytes_read=5644 bytes_retransmit=0 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009095 adj=50011960 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1781 bytes_read=10302 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999427 adj=63999542 Octopus_V1.1_F446: temp=31.3 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=662 bytes_read=18684 bytes_retransmit=0 bytes_invalid=0 send_seq=109 receive_seq=109 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999642 adj=31999664 coil_temp=35.8 refs=0 mcu_temp=33.77 supply_voltage=3.014 sysload=0.24 cputime=3422.503 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=115.4 pwm=0.000
Stats 70988.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4333 bytes_read=14155 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999573 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=1164 bytes_read=5673 bytes_retransmit=0 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009167 adj=50012046 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1787 bytes_read=10419 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999425 adj=63999625 Octopus_V1.1_F446: temp=31.4 EBB42_v1.2_T0: temp=34.6 raspberry_pi: temp=33.1  heater_bed: target=0 temp=50.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=668 bytes_read=19040 bytes_retransmit=0 bytes_invalid=0 send_seq=110 receive_seq=110 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999641 adj=31999674 coil_temp=35.8 refs=0 mcu_temp=33.81 supply_voltage=3.014 sysload=0.24 cputime=3422.558 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=115.0 pwm=0.000
Stats 70989.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4339 bytes_read=14258 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999570 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=1170 bytes_read=5689 bytes_retransmit=0 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009238 adj=50012120 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1793 bytes_read=10551 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999424 adj=63999604 Octopus_V1.1_F446: temp=31.1 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.6  heater_bed: target=0 temp=50.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=674 bytes_read=19396 bytes_retransmit=0 bytes_invalid=0 send_seq=111 receive_seq=111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999639 adj=31999681 coil_temp=35.8 refs=0 mcu_temp=33.85 supply_voltage=3.014 sysload=0.22 cputime=3422.614 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=113.6 pwm=0.000
Stats 70990.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4345 bytes_read=14404 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999569 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=1176 bytes_read=5705 bytes_retransmit=0 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009308 adj=50012193 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1799 bytes_read=10654 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999595 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=34.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=50.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=680 bytes_read=19752 bytes_retransmit=0 bytes_invalid=0 send_seq=112 receive_seq=112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999638 adj=31999677 coil_temp=35.8 refs=0 mcu_temp=33.91 supply_voltage=3.014 sysload=0.22 cputime=3422.670 memavail=1403968 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=113.2 pwm=0.000
Stats 70991.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4351 bytes_read=14507 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999603 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=1182 bytes_read=5721 bytes_retransmit=0 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009378 adj=50012264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1805 bytes_read=10757 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999420 adj=63999572 Octopus_V1.1_F446: temp=31.2 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.1  heater_bed: target=0 temp=50.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=686 bytes_read=20092 bytes_retransmit=0 bytes_invalid=0 send_seq=113 receive_seq=113 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999640 adj=31999683 coil_temp=35.8 refs=0 mcu_temp=33.94 supply_voltage=3.014 sysload=0.22 cputime=3422.724 memavail=1402960 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=112.3 pwm=0.000
Stats 70992.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4357 bytes_read=14610 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999596 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000023 bytes_write=1188 bytes_read=5737 bytes_retransmit=0 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009448 adj=50012222 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1811 bytes_read=10889 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999419 adj=63999416 Octopus_V1.1_F446: temp=31.1 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.1  heater_bed: target=0 temp=50.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=692 bytes_read=20448 bytes_retransmit=0 bytes_invalid=0 send_seq=114 receive_seq=114 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999641 adj=31999641 coil_temp=35.9 refs=0 mcu_temp=33.96 supply_voltage=3.014 sysload=0.22 cputime=3422.779 memavail=1402976 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=111.5 pwm=0.000
Stats 70993.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4363 bytes_read=14742 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999588 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000021 bytes_write=1194 bytes_read=5766 bytes_retransmit=0 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009518 adj=50012341 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1817 bytes_read=11006 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999426 adj=63999466 Octopus_V1.1_F446: temp=31.1 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=698 bytes_read=20804 bytes_retransmit=0 bytes_invalid=0 send_seq=115 receive_seq=115 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999646 adj=31999680 coil_temp=35.9 refs=0 mcu_temp=34.00 supply_voltage=3.014 sysload=0.22 cputime=3422.836 memavail=1402476 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=110.9 pwm=0.000
Stats 70994.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4369 bytes_read=14845 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999577 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000021 bytes_write=1200 bytes_read=5782 bytes_retransmit=0 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009577 adj=50012471 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1823 bytes_read=11103 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999422 adj=63999611 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=704 bytes_read=21160 bytes_retransmit=0 bytes_invalid=0 send_seq=116 receive_seq=116 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999643 adj=31999763 coil_temp=35.9 refs=0 mcu_temp=34.02 supply_voltage=3.014 sysload=0.29 cputime=3422.867 memavail=1402716 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=110.4 pwm=0.000
Stats 70995.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4375 bytes_read=14962 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999562 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000021 bytes_write=1206 bytes_read=5798 bytes_retransmit=0 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009634 adj=50012462 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1829 bytes_read=11225 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999417 adj=63999590 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6  heater_bed: target=0 temp=50.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=710 bytes_read=21516 bytes_retransmit=0 bytes_invalid=0 send_seq=117 receive_seq=117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999640 adj=31999740 coil_temp=35.9 refs=0 mcu_temp=34.05 supply_voltage=3.014 sysload=0.29 cputime=3422.891 memavail=1402736 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=109.6 pwm=0.000
Stats 70996.8: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4381 bytes_read=15094 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999550 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000021 bytes_write=1212 bytes_read=5814 bytes_retransmit=0 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009690 adj=50012471 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1835 bytes_read=11321 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999418 adj=63999591 Octopus_V1.1_F446: temp=31.0 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.1  heater_bed: target=0 temp=50.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=716 bytes_read=21872 bytes_retransmit=0 bytes_invalid=0 send_seq=118 receive_seq=118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999636 adj=31999734 coil_temp=36.0 refs=0 mcu_temp=34.07 supply_voltage=3.014 sysload=0.29 cputime=3422.914 memavail=1402736 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=109.0 pwm=0.000
Stats 70997.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4387 bytes_read=15197 bytes_retransmit=9 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999536 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000021 bytes_write=1218 bytes_read=5830 bytes_retransmit=0 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009747 adj=50012488 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1841 bytes_read=11417 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999424 adj=63999654 Octopus_V1.1_F446: temp=30.9 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=722 bytes_read=22228 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999633 adj=31999713 coil_temp=36.0 refs=0 mcu_temp=34.10 supply_voltage=3.014 sysload=0.29 cputime=3422.939 memavail=1401676 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=108.2 pwm=0.000
Stats 70998.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4393 bytes_read=15300 bytes_retransmit=9 bytes_invalid=0 send_seq=393 receive_seq=393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999526 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1224 bytes_read=5859 bytes_retransmit=0 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009804 adj=50012528 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1847 bytes_read=11560 bytes_retransmit=9 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999418 adj=63999757 Octopus_V1.1_F446: temp=30.9 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=35.0  heater_bed: target=0 temp=49.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=728 bytes_read=22584 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999629 adj=31999702 coil_temp=36.0 refs=0 mcu_temp=34.14 supply_voltage=3.014 sysload=0.29 cputime=3422.962 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=107.6 pwm=0.000
Stats 70999.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4399 bytes_read=15432 bytes_retransmit=9 bytes_invalid=0 send_seq=394 receive_seq=394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999531 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1230 bytes_read=5875 bytes_retransmit=0 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009870 adj=50012570 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1853 bytes_read=11663 bytes_retransmit=9 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999420 adj=63999696 Octopus_V1.1_F446: temp=30.7 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=35.5  heater_bed: target=0 temp=49.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=734 bytes_read=22940 bytes_retransmit=0 bytes_invalid=0 send_seq=121 receive_seq=121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999628 adj=31999693 coil_temp=36.0 refs=0 mcu_temp=34.16 supply_voltage=3.014 sysload=0.26 cputime=3423.011 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=107.1 pwm=0.000
Stats 71000.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4405 bytes_read=15545 bytes_retransmit=9 bytes_invalid=0 send_seq=395 receive_seq=395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999532 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1236 bytes_read=5891 bytes_retransmit=0 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009941 adj=50012678 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1859 bytes_read=11766 bytes_retransmit=9 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999418 adj=63999666 Octopus_V1.1_F446: temp=30.8 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=740 bytes_read=23296 bytes_retransmit=0 bytes_invalid=0 send_seq=122 receive_seq=122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999630 adj=31999673 coil_temp=36.0 refs=0 mcu_temp=34.18 supply_voltage=3.014 sysload=0.26 cputime=3423.068 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=106.2 pwm=0.000
Stats 71001.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4411 bytes_read=15641 bytes_retransmit=9 bytes_invalid=0 send_seq=396 receive_seq=396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999533 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1242 bytes_read=5907 bytes_retransmit=0 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010000 adj=50012853 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1865 bytes_read=11898 bytes_retransmit=9 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999415 adj=63999617 Octopus_V1.1_F446: temp=30.7 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=746 bytes_read=23652 bytes_retransmit=0 bytes_invalid=0 send_seq=123 receive_seq=123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999628 adj=31999697 coil_temp=36.0 refs=0 mcu_temp=34.21 supply_voltage=3.014 sysload=0.26 cputime=3423.121 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=105.4 pwm=0.000
Stats 71002.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4417 bytes_read=15772 bytes_retransmit=9 bytes_invalid=0 send_seq=397 receive_seq=397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999533 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1248 bytes_read=5923 bytes_retransmit=0 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010063 adj=50012875 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1871 bytes_read=12001 bytes_retransmit=9 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999579 Octopus_V1.1_F446: temp=30.7 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=752 bytes_read=24008 bytes_retransmit=0 bytes_invalid=0 send_seq=124 receive_seq=124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999628 adj=31999684 coil_temp=36.1 refs=0 mcu_temp=34.23 supply_voltage=3.014 sysload=0.26 cputime=3423.176 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=104.9 pwm=0.000
Stats 71003.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4423 bytes_read=15875 bytes_retransmit=9 bytes_invalid=0 send_seq=398 receive_seq=398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999535 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1254 bytes_read=5952 bytes_retransmit=0 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010124 adj=50012953 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1877 bytes_read=12104 bytes_retransmit=9 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999414 adj=63999563 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=758 bytes_read=24364 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999627 adj=31999685 coil_temp=36.1 refs=0 mcu_temp=34.25 supply_voltage=3.014 sysload=0.26 cputime=3423.231 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=104.5 pwm=0.000
Stats 71004.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4429 bytes_read=15978 bytes_retransmit=9 bytes_invalid=0 send_seq=399 receive_seq=399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999535 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1260 bytes_read=5968 bytes_retransmit=0 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010185 adj=50013006 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1883 bytes_read=12250 bytes_retransmit=9 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999412 adj=63999554 Octopus_V1.1_F446: temp=30.7 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=764 bytes_read=24720 bytes_retransmit=0 bytes_invalid=0 send_seq=126 receive_seq=126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999627 adj=31999676 coil_temp=36.1 refs=0 mcu_temp=34.28 supply_voltage=3.014 sysload=0.24 cputime=3423.286 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=103.6 pwm=0.000
Stats 71005.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4441 bytes_read=16140 bytes_retransmit=9 bytes_invalid=0 send_seq=401 receive_seq=401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999532 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1266 bytes_read=5984 bytes_retransmit=0 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010250 adj=50013064 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1895 bytes_read=12369 bytes_retransmit=9 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999411 adj=63999542 Octopus_V1.1_F446: temp=30.6 EBB42_v1.2_T0: temp=34.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=770 bytes_read=25076 bytes_retransmit=0 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999627 adj=31999690 coil_temp=36.1 refs=0 mcu_temp=34.31 supply_voltage=3.014 sysload=0.24 cputime=3423.343 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=103.1 pwm=0.000
Stats 71006.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4447 bytes_read=16243 bytes_retransmit=9 bytes_invalid=0 send_seq=402 receive_seq=402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999529 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1272 bytes_read=6000 bytes_retransmit=0 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010309 adj=50013193 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1901 bytes_read=12472 bytes_retransmit=9 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999409 adj=63999544 Octopus_V1.1_F446: temp=30.5 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=776 bytes_read=25432 bytes_retransmit=0 bytes_invalid=0 send_seq=128 receive_seq=128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999626 adj=31999701 coil_temp=36.1 refs=0 mcu_temp=34.34 supply_voltage=3.014 sysload=0.24 cputime=3423.396 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=102.5 pwm=0.000
Stats 71007.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4453 bytes_read=16346 bytes_retransmit=9 bytes_invalid=0 send_seq=403 receive_seq=403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999526 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1284 bytes_read=6032 bytes_retransmit=0 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010424 adj=50013236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1907 bytes_read=12604 bytes_retransmit=9 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999410 adj=63999546 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.1  heater_bed: target=0 temp=49.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=782 bytes_read=25788 bytes_retransmit=0 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999626 adj=31999700 coil_temp=36.1 refs=0 mcu_temp=34.36 supply_voltage=3.014 sysload=0.24 cputime=3423.451 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=101.6 pwm=0.000
Stats 71008.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4459 bytes_read=16478 bytes_retransmit=9 bytes_invalid=0 send_seq=404 receive_seq=404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999525 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1290 bytes_read=6048 bytes_retransmit=0 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010479 adj=50013988 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1913 bytes_read=12707 bytes_retransmit=9 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999408 adj=63999578 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=788 bytes_read=26144 bytes_retransmit=0 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999625 adj=31999704 coil_temp=36.1 refs=0 mcu_temp=34.39 supply_voltage=3.014 sysload=0.24 cputime=3423.505 memavail=1401732 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=101.4 pwm=0.000
Stats 71009.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4465 bytes_read=16581 bytes_retransmit=9 bytes_invalid=0 send_seq=405 receive_seq=405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999524 rpi: mcu_awake=0.001 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=1296 bytes_read=6077 bytes_retransmit=0 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010534 adj=50013816 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1919 bytes_read=12824 bytes_retransmit=9 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999406 adj=63999561 Octopus_V1.1_F446: temp=30.4 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=794 bytes_read=26500 bytes_retransmit=0 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999624 adj=31999697 coil_temp=36.2 refs=0 mcu_temp=34.41 supply_voltage=3.014 sysload=0.22 cputime=3423.560 memavail=1401272 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=100.7 pwm=0.000
Stats 71010.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4471 bytes_read=16698 bytes_retransmit=9 bytes_invalid=0 send_seq=406 receive_seq=406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999526 rpi: mcu_awake=0.001 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=1302 bytes_read=6093 bytes_retransmit=0 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010588 adj=50013704 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1925 bytes_read=12956 bytes_retransmit=9 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999405 adj=63999538 Octopus_V1.1_F446: temp=30.2 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=32.1  heater_bed: target=0 temp=49.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=800 bytes_read=26856 bytes_retransmit=0 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999623 adj=31999691 coil_temp=36.2 refs=0 mcu_temp=34.43 supply_voltage=3.014 sysload=0.22 cputime=3423.615 memavail=1401272 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=99.9 pwm=0.000
Stats 71011.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4477 bytes_read=16830 bytes_retransmit=9 bytes_invalid=0 send_seq=407 receive_seq=407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999520 rpi: mcu_awake=0.001 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=1308 bytes_read=6109 bytes_retransmit=0 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010635 adj=50013623 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1931 bytes_read=13059 bytes_retransmit=9 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999402 adj=63999533 Octopus_V1.1_F446: temp=30.3 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=806 bytes_read=27212 bytes_retransmit=0 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999622 adj=31999675 coil_temp=36.2 refs=0 mcu_temp=34.45 supply_voltage=3.014 sysload=0.22 cputime=3423.651 memavail=1402540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=99.4 pwm=0.000
Stats 71012.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4483 bytes_read=16933 bytes_retransmit=9 bytes_invalid=0 send_seq=408 receive_seq=408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999520 rpi: mcu_awake=0.001 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=1314 bytes_read=6125 bytes_retransmit=0 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010683 adj=50013519 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1937 bytes_read=13162 bytes_retransmit=9 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999400 adj=63999525 Octopus_V1.1_F446: temp=30.2 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.1  heater_bed: target=0 temp=49.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=812 bytes_read=27568 bytes_retransmit=0 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999620 adj=31999684 coil_temp=36.2 refs=0 mcu_temp=34.48 supply_voltage=3.014 sysload=0.22 cputime=3423.674 memavail=1402540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=98.8 pwm=0.000
Stats 71013.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4489 bytes_read=17036 bytes_retransmit=9 bytes_invalid=0 send_seq=409 receive_seq=409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999515 rpi: mcu_awake=0.001 mcu_task_avg=0.000022 mcu_task_stddev=0.000026 bytes_write=1320 bytes_read=6140 bytes_retransmit=0 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010729 adj=50013435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1943 bytes_read=13294 bytes_retransmit=9 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999396 adj=63999507 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=818 bytes_read=27924 bytes_retransmit=0 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999618 adj=31999669 coil_temp=36.2 refs=0 mcu_temp=34.50 supply_voltage=3.014 sysload=0.22 cputime=3423.698 memavail=1402540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=98.4 pwm=0.000
Stats 71014.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4495 bytes_read=17168 bytes_retransmit=9 bytes_invalid=0 send_seq=410 receive_seq=410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999508 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=1326 bytes_read=6168 bytes_retransmit=0 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010774 adj=50013393 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1949 bytes_read=13411 bytes_retransmit=9 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999392 adj=63999495 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=824 bytes_read=28280 bytes_retransmit=0 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999615 adj=31999656 coil_temp=36.2 refs=0 mcu_temp=34.51 supply_voltage=3.014 sysload=0.36 cputime=3423.723 memavail=1401492 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=97.6 pwm=0.000
Stats 71015.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4501 bytes_read=17285 bytes_retransmit=9 bytes_invalid=0 send_seq=411 receive_seq=411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999501 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=1332 bytes_read=6183 bytes_retransmit=0 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010819 adj=50013370 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1955 bytes_read=13514 bytes_retransmit=9 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999391 adj=63999505 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=830 bytes_read=28636 bytes_retransmit=0 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999613 adj=31999651 coil_temp=36.2 refs=0 mcu_temp=34.53 supply_voltage=3.014 sysload=0.36 cputime=3423.746 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=97.1 pwm=0.000
Stats 71016.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4507 bytes_read=17388 bytes_retransmit=9 bytes_invalid=0 send_seq=412 receive_seq=412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999502 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=1338 bytes_read=6198 bytes_retransmit=0 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010871 adj=50013358 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1961 bytes_read=13646 bytes_retransmit=9 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999533 Octopus_V1.1_F446: temp=30.1 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=836 bytes_read=28992 bytes_retransmit=0 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999615 adj=31999652 coil_temp=36.3 refs=0 mcu_temp=34.55 supply_voltage=3.014 sysload=0.36 cputime=3423.791 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=96.6 pwm=0.000
Stats 71017.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4513 bytes_read=17520 bytes_retransmit=9 bytes_invalid=0 send_seq=413 receive_seq=413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999507 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=1344 bytes_read=6213 bytes_retransmit=0 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010922 adj=50013435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1967 bytes_read=13749 bytes_retransmit=9 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999525 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=842 bytes_read=29348 bytes_retransmit=0 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999615 adj=31999689 coil_temp=36.3 refs=0 mcu_temp=34.58 supply_voltage=3.014 sysload=0.36 cputime=3423.844 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=96.1 pwm=0.000
Stats 71018.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4519 bytes_read=17623 bytes_retransmit=9 bytes_invalid=0 send_seq=414 receive_seq=414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999508 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000015 bytes_write=1350 bytes_read=6229 bytes_retransmit=0 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010974 adj=50013481 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1973 bytes_read=13852 bytes_retransmit=9 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999513 Octopus_V1.1_F446: temp=30.0 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=848 bytes_read=29704 bytes_retransmit=0 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999614 adj=31999680 coil_temp=36.3 refs=0 mcu_temp=34.61 supply_voltage=3.014 sysload=0.36 cputime=3423.897 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=95.5 pwm=0.000
Stats 71019.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4525 bytes_read=17726 bytes_retransmit=9 bytes_invalid=0 send_seq=415 receive_seq=415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999508 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000017 bytes_write=1356 bytes_read=6258 bytes_retransmit=0 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011025 adj=50013551 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1979 bytes_read=13998 bytes_retransmit=9 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999389 adj=63999520 Octopus_V1.1_F446: temp=29.9 EBB42_v1.2_T0: temp=34.8 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=854 bytes_read=30060 bytes_retransmit=0 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999680 coil_temp=36.3 refs=0 mcu_temp=34.64 supply_voltage=3.014 sysload=0.34 cputime=3423.952 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=95.1 pwm=0.000
Stats 71020.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4531 bytes_read=17872 bytes_retransmit=9 bytes_invalid=0 send_seq=416 receive_seq=416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999509 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000017 bytes_write=1362 bytes_read=6274 bytes_retransmit=0 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011072 adj=50013624 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1985 bytes_read=14101 bytes_retransmit=9 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999526 Octopus_V1.1_F446: temp=29.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=32.6  heater_bed: target=0 temp=49.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=860 bytes_read=30416 bytes_retransmit=0 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999713 coil_temp=36.3 refs=0 mcu_temp=34.67 supply_voltage=3.014 sysload=0.34 cputime=3424.006 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=94.4 pwm=0.000
Stats 71021.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4537 bytes_read=17975 bytes_retransmit=9 bytes_invalid=0 send_seq=417 receive_seq=417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999514 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000017 bytes_write=1368 bytes_read=6290 bytes_retransmit=0 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011120 adj=50013624 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1991 bytes_read=14204 bytes_retransmit=9 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999544 Octopus_V1.1_F446: temp=29.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=35.5  heater_bed: target=0 temp=49.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=866 bytes_read=30772 bytes_retransmit=0 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999697 coil_temp=36.3 refs=0 mcu_temp=34.69 supply_voltage=3.014 sysload=0.34 cputime=3424.061 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=93.8 pwm=0.000
Stats 71022.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4543 bytes_read=18078 bytes_retransmit=9 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999518 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000017 bytes_write=1374 bytes_read=6306 bytes_retransmit=0 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011169 adj=50013639 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=1997 bytes_read=14336 bytes_retransmit=9 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999520 Octopus_V1.1_F446: temp=29.9 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=872 bytes_read=31128 bytes_retransmit=0 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999618 adj=31999688 coil_temp=36.3 refs=0 mcu_temp=34.72 supply_voltage=3.014 sysload=0.34 cputime=3424.116 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=93.4 pwm=0.000
Stats 71023.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4549 bytes_read=18210 bytes_retransmit=9 bytes_invalid=0 send_seq=419 receive_seq=419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999521 rpi: mcu_awake=0.001 mcu_task_avg=0.000014 mcu_task_stddev=0.000017 bytes_write=1380 bytes_read=6322 bytes_retransmit=0 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011217 adj=50013686 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2003 bytes_read=14439 bytes_retransmit=9 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999509 Octopus_V1.1_F446: temp=29.8 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=878 bytes_read=31484 bytes_retransmit=0 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999620 adj=31999707 coil_temp=36.4 refs=0 mcu_temp=34.73 supply_voltage=3.014 sysload=0.34 cputime=3424.171 memavail=1401324 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=92.9 pwm=0.000
Stats 71024.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4555 bytes_read=18308 bytes_retransmit=9 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999527 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1386 bytes_read=6351 bytes_retransmit=0 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011265 adj=50013724 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2009 bytes_read=14556 bytes_retransmit=9 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999508 Octopus_V1.1_F446: temp=29.7 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=884 bytes_read=31840 bytes_retransmit=0 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999619 adj=31999730 coil_temp=36.4 refs=0 mcu_temp=34.75 supply_voltage=3.014 sysload=0.31 cputime=3424.225 memavail=1401100 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=92.3 pwm=0.000
Stats 71025.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4561 bytes_read=18418 bytes_retransmit=9 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999533 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1392 bytes_read=6367 bytes_retransmit=0 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011313 adj=50013764 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2015 bytes_read=14688 bytes_retransmit=9 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999395 adj=63999495 Octopus_V1.1_F446: temp=29.6 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=890 bytes_read=32196 bytes_retransmit=0 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999617 adj=31999700 coil_temp=36.4 refs=0 mcu_temp=34.75 supply_voltage=3.014 sysload=0.31 cputime=3424.279 memavail=1401100 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=91.7 pwm=0.000
Stats 71026.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4567 bytes_read=18550 bytes_retransmit=9 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999534 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1398 bytes_read=6383 bytes_retransmit=0 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011362 adj=50013798 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2021 bytes_read=14791 bytes_retransmit=9 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999394 adj=63999549 Octopus_V1.1_F446: temp=29.7 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.6  heater_bed: target=0 temp=49.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=896 bytes_read=32552 bytes_retransmit=0 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999616 adj=31999661 coil_temp=36.4 refs=0 mcu_temp=34.76 supply_voltage=3.014 sysload=0.31 cputime=3424.333 memavail=1401300 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=91.3 pwm=0.000
Stats 71027.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4573 bytes_read=18653 bytes_retransmit=9 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999533 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1404 bytes_read=6399 bytes_retransmit=0 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011406 adj=50013869 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2027 bytes_read=14894 bytes_retransmit=9 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999393 adj=63999533 Octopus_V1.1_F446: temp=29.7 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=908 bytes_read=32924 bytes_retransmit=0 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999614 adj=31999655 coil_temp=36.4 refs=0 mcu_temp=34.76 supply_voltage=3.014 sysload=0.31 cputime=3424.386 memavail=1401352 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=90.8 pwm=0.000
Stats 71028.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4579 bytes_read=18756 bytes_retransmit=9 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999530 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1410 bytes_read=6415 bytes_retransmit=0 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011446 adj=50013888 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2033 bytes_read=15026 bytes_retransmit=9 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999531 Octopus_V1.1_F446: temp=29.6 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=914 bytes_read=33280 bytes_retransmit=0 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999612 adj=31999632 coil_temp=36.4 refs=0 mcu_temp=34.77 supply_voltage=3.014 sysload=0.31 cputime=3424.429 memavail=1397572 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=90.3 pwm=0.000
Stats 71029.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4585 bytes_read=18888 bytes_retransmit=9 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999540 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=1416 bytes_read=6444 bytes_retransmit=0 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011482 adj=50013850 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2039 bytes_read=15143 bytes_retransmit=9 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999396 adj=63999517 Octopus_V1.1_F446: temp=29.5 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=920 bytes_read=33636 bytes_retransmit=0 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999609 adj=31999631 coil_temp=36.4 refs=0 mcu_temp=34.78 supply_voltage=3.014 sysload=0.28 cputime=3424.454 memavail=1403368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=89.9 pwm=0.000
Stats 71030.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4591 bytes_read=19005 bytes_retransmit=9 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999535 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=1422 bytes_read=6460 bytes_retransmit=0 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011519 adj=50013749 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2045 bytes_read=15246 bytes_retransmit=9 bytes_invalid=0 send_seq=249 receive_seq=249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999393 adj=63999557 Octopus_V1.1_F446: temp=29.3 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=49.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=926 bytes_read=33992 bytes_retransmit=0 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999608 adj=31999586 coil_temp=36.4 refs=0 mcu_temp=34.79 supply_voltage=3.014 sysload=0.28 cputime=3424.477 memavail=1403368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=89.6 pwm=0.000
Stats 71031.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4597 bytes_read=19108 bytes_retransmit=9 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999528 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=1428 bytes_read=6476 bytes_retransmit=0 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011556 adj=50013738 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2051 bytes_read=15378 bytes_retransmit=9 bytes_invalid=0 send_seq=250 receive_seq=250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999390 adj=63999544 Octopus_V1.1_F446: temp=29.3 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1  heater_bed: target=0 temp=49.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=932 bytes_read=34348 bytes_retransmit=0 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999606 adj=31999606 coil_temp=36.4 refs=0 mcu_temp=34.80 supply_voltage=3.014 sysload=0.28 cputime=3424.501 memavail=1403368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=88.8 pwm=0.000
Stats 71032.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4603 bytes_read=19240 bytes_retransmit=9 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999523 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=1434 bytes_read=6492 bytes_retransmit=0 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011592 adj=50013751 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2057 bytes_read=15481 bytes_retransmit=9 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999387 adj=63999539 Octopus_V1.1_F446: temp=29.3 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=938 bytes_read=34704 bytes_retransmit=0 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999604 adj=31999617 coil_temp=36.4 refs=0 mcu_temp=34.82 supply_voltage=3.014 sysload=0.28 cputime=3424.524 memavail=1403368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=88.2 pwm=0.000
Stats 71033.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4609 bytes_read=19343 bytes_retransmit=9 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999518 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000020 bytes_write=1440 bytes_read=6508 bytes_retransmit=0 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011632 adj=50013762 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2063 bytes_read=15584 bytes_retransmit=9 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999385 adj=63999530 Octopus_V1.1_F446: temp=29.5 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=944 bytes_read=35060 bytes_retransmit=0 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999604 adj=31999627 coil_temp=36.4 refs=0 mcu_temp=34.84 supply_voltage=3.014 sysload=0.28 cputime=3424.562 memavail=1403380 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=87.8 pwm=0.000
Stats 71034.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4615 bytes_read=19446 bytes_retransmit=9 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999526 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1446 bytes_read=6537 bytes_retransmit=0 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011677 adj=50013836 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2069 bytes_read=15730 bytes_retransmit=9 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999385 adj=63999525 Octopus_V1.1_F446: temp=29.4 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=950 bytes_read=35416 bytes_retransmit=0 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999603 adj=31999656 coil_temp=36.4 refs=0 mcu_temp=34.85 supply_voltage=3.014 sysload=0.26 cputime=3424.616 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=87.2 pwm=0.000
Stats 71035.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4621 bytes_read=19592 bytes_retransmit=9 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999530 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1452 bytes_read=6553 bytes_retransmit=0 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011718 adj=50013920 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2075 bytes_read=15833 bytes_retransmit=9 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999385 adj=63999504 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=956 bytes_read=35772 bytes_retransmit=0 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999634 coil_temp=36.4 refs=0 mcu_temp=34.88 supply_voltage=3.014 sysload=0.26 cputime=3424.671 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=86.8 pwm=0.000
Stats 71036.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4627 bytes_read=19695 bytes_retransmit=9 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999532 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1458 bytes_read=6569 bytes_retransmit=0 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011760 adj=50013947 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2081 bytes_read=15936 bytes_retransmit=9 bytes_invalid=0 send_seq=255 receive_seq=255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999385 adj=63999490 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=962 bytes_read=36128 bytes_retransmit=0 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999601 adj=31999620 coil_temp=36.5 refs=0 mcu_temp=34.88 supply_voltage=3.014 sysload=0.26 cputime=3424.724 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=86.6 pwm=0.000
Stats 71037.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4633 bytes_read=19798 bytes_retransmit=9 bytes_invalid=0 send_seq=433 receive_seq=433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999534 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1464 bytes_read=6585 bytes_retransmit=0 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011802 adj=50014004 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2087 bytes_read=16068 bytes_retransmit=9 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999384 adj=63999496 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=968 bytes_read=36484 bytes_retransmit=0 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999600 adj=31999620 coil_temp=36.5 refs=0 mcu_temp=34.89 supply_voltage=3.014 sysload=0.26 cputime=3424.778 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=86.0 pwm=0.000
Stats 71038.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4639 bytes_read=19930 bytes_retransmit=9 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999538 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1470 bytes_read=6601 bytes_retransmit=0 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011839 adj=50014068 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2093 bytes_read=16171 bytes_retransmit=9 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999384 adj=63999489 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=974 bytes_read=36840 bytes_retransmit=0 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999600 adj=31999618 coil_temp=36.5 refs=0 mcu_temp=34.90 supply_voltage=3.014 sysload=0.26 cputime=3424.831 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=85.6 pwm=0.000
Stats 71039.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4645 bytes_read=20033 bytes_retransmit=9 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999540 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1476 bytes_read=6630 bytes_retransmit=0 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011878 adj=50014042 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2099 bytes_read=16288 bytes_retransmit=9 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999474 Octopus_V1.1_F446: temp=28.9 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=980 bytes_read=37196 bytes_retransmit=0 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999600 adj=31999625 coil_temp=36.5 refs=0 mcu_temp=34.92 supply_voltage=3.014 sysload=0.24 cputime=3424.885 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=85.1 pwm=0.000
Stats 71040.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4651 bytes_read=20150 bytes_retransmit=9 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999558 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1482 bytes_read=6646 bytes_retransmit=0 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011918 adj=50014062 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2105 bytes_read=16420 bytes_retransmit=9 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999478 Octopus_V1.1_F446: temp=29.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=986 bytes_read=37552 bytes_retransmit=0 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999599 adj=31999625 coil_temp=36.5 refs=0 mcu_temp=34.94 supply_voltage=3.014 sysload=0.24 cputime=3424.939 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=84.7 pwm=0.000
Stats 71041.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4657 bytes_read=20282 bytes_retransmit=9 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999558 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1488 bytes_read=6662 bytes_retransmit=0 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011956 adj=50014050 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2111 bytes_read=16523 bytes_retransmit=9 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999407 Octopus_V1.1_F446: temp=29.0 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=992 bytes_read=37908 bytes_retransmit=0 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999591 coil_temp=36.5 refs=0 mcu_temp=34.94 supply_voltage=3.014 sysload=0.24 cputime=3424.992 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=84.1 pwm=0.000
Stats 71042.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4663 bytes_read=20385 bytes_retransmit=9 bytes_invalid=0 send_seq=438 receive_seq=438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999557 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1494 bytes_read=6678 bytes_retransmit=0 bytes_invalid=0 send_seq=223 receive_seq=223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011992 adj=50014089 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2117 bytes_read=16626 bytes_retransmit=9 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999439 Octopus_V1.1_F446: temp=29.0 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=998 bytes_read=38264 bytes_retransmit=0 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999650 coil_temp=36.5 refs=0 mcu_temp=34.96 supply_voltage=3.014 sysload=0.24 cputime=3425.046 memavail=1403156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=83.8 pwm=0.000
Stats 71043.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4669 bytes_read=20488 bytes_retransmit=9 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999560 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000020 bytes_write=1500 bytes_read=6694 bytes_retransmit=0 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012026 adj=50014110 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2123 bytes_read=16758 bytes_retransmit=9 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999384 adj=63999468 Octopus_V1.1_F446: temp=28.9 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1004 bytes_read=38620 bytes_retransmit=0 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999663 coil_temp=36.5 refs=0 mcu_temp=34.96 supply_voltage=3.014 sysload=0.24 cputime=3425.100 memavail=1402400 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=83.3 pwm=0.000
Stats 71044.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4675 bytes_read=20620 bytes_retransmit=9 bytes_invalid=0 send_seq=440 receive_seq=440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999560 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1506 bytes_read=6723 bytes_retransmit=0 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012059 adj=50014087 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2129 bytes_read=16873 bytes_retransmit=9 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999477 Octopus_V1.1_F446: temp=28.9 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1010 bytes_read=38976 bytes_retransmit=0 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999662 coil_temp=36.5 refs=0 mcu_temp=34.98 supply_voltage=3.014 sysload=0.22 cputime=3425.156 memavail=1401920 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=82.8 pwm=0.000
Stats 71045.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4681 bytes_read=20723 bytes_retransmit=9 bytes_invalid=0 send_seq=441 receive_seq=441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999558 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1512 bytes_read=6739 bytes_retransmit=0 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012093 adj=50014084 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2135 bytes_read=16973 bytes_retransmit=9 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999383 adj=63999481 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1016 bytes_read=39332 bytes_retransmit=0 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999602 adj=31999657 coil_temp=36.5 refs=0 mcu_temp=34.98 supply_voltage=3.014 sysload=0.22 cputime=3425.207 memavail=1395872 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=82.3 pwm=0.000
Stats 71046.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4687 bytes_read=20840 bytes_retransmit=9 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999552 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1518 bytes_read=6755 bytes_retransmit=0 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012121 adj=50014098 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2141 bytes_read=17101 bytes_retransmit=9 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999382 adj=63999511 Octopus_V1.1_F446: temp=28.9 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1022 bytes_read=39688 bytes_retransmit=0 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999601 adj=31999666 coil_temp=36.6 refs=0 mcu_temp=35.00 supply_voltage=3.014 sysload=0.22 cputime=3425.231 memavail=1401924 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=82.1 pwm=0.000
Stats 71047.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4693 bytes_read=20972 bytes_retransmit=9 bytes_invalid=0 send_seq=443 receive_seq=443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999552 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1524 bytes_read=6771 bytes_retransmit=0 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012149 adj=50014066 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2147 bytes_read=17201 bytes_retransmit=9 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999532 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1028 bytes_read=40044 bytes_retransmit=0 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999598 adj=31999673 coil_temp=36.6 refs=0 mcu_temp=35.01 supply_voltage=3.014 sysload=0.22 cputime=3425.254 memavail=1401924 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=81.7 pwm=0.000
Stats 71048.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4699 bytes_read=21068 bytes_retransmit=9 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999547 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000024 bytes_write=1530 bytes_read=6787 bytes_retransmit=0 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012177 adj=50014012 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2153 bytes_read=17301 bytes_retransmit=9 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999517 Octopus_V1.1_F446: temp=28.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1034 bytes_read=40400 bytes_retransmit=0 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999596 adj=31999639 coil_temp=36.6 refs=0 mcu_temp=35.02 supply_voltage=3.014 sysload=0.22 cputime=3425.277 memavail=1401924 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=81.4 pwm=0.000
Stats 71049.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4705 bytes_read=21166 bytes_retransmit=9 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999552 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000024 bytes_write=1536 bytes_read=6816 bytes_retransmit=0 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012205 adj=50014006 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2159 bytes_read=17443 bytes_retransmit=9 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999382 adj=63999536 Octopus_V1.1_F446: temp=28.7 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1040 bytes_read=40756 bytes_retransmit=0 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999595 adj=31999631 coil_temp=36.6 refs=0 mcu_temp=35.04 supply_voltage=3.014 sysload=0.20 cputime=3425.301 memavail=1401620 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=80.6 pwm=0.000
Stats 71050.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4711 bytes_read=21298 bytes_retransmit=9 bytes_invalid=0 send_seq=446 receive_seq=446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999552 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000024 bytes_write=1542 bytes_read=6832 bytes_retransmit=0 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012233 adj=50013968 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2165 bytes_read=17543 bytes_retransmit=9 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999545 Octopus_V1.1_F446: temp=28.7 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1046 bytes_read=41112 bytes_retransmit=0 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999593 adj=31999613 coil_temp=36.6 refs=0 mcu_temp=35.04 supply_voltage=3.014 sysload=0.20 cputime=3425.333 memavail=1401620 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=80.3 pwm=0.000
Stats 71051.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4717 bytes_read=21415 bytes_retransmit=9 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999555 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000024 bytes_write=1548 bytes_read=6848 bytes_retransmit=0 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012266 adj=50013973 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2171 bytes_read=17643 bytes_retransmit=9 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999509 Octopus_V1.1_F446: temp=28.6 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1052 bytes_read=41468 bytes_retransmit=0 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999592 adj=31999598 coil_temp=36.6 refs=0 mcu_temp=35.05 supply_voltage=3.014 sysload=0.20 cputime=3425.388 memavail=1401676 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=79.9 pwm=0.000
Stats 71052.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4723 bytes_read=21518 bytes_retransmit=9 bytes_invalid=0 send_seq=448 receive_seq=448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999560 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000024 bytes_write=1554 bytes_read=6864 bytes_retransmit=0 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012298 adj=50014040 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2177 bytes_read=17771 bytes_retransmit=9 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999382 adj=63999524 Octopus_V1.1_F446: temp=28.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1058 bytes_read=41824 bytes_retransmit=0 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999591 adj=31999595 coil_temp=36.6 refs=0 mcu_temp=35.06 supply_voltage=3.014 sysload=0.20 cputime=3425.444 memavail=1401452 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=79.5 pwm=0.000
Stats 71053.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4729 bytes_read=21650 bytes_retransmit=9 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999561 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000024 bytes_write=1560 bytes_read=6880 bytes_retransmit=0 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012330 adj=50014070 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2183 bytes_read=17871 bytes_retransmit=9 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999506 Octopus_V1.1_F446: temp=28.5 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=32.1  heater_bed: target=0 temp=48.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1064 bytes_read=42180 bytes_retransmit=0 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999588 coil_temp=36.6 refs=0 mcu_temp=35.07 supply_voltage=3.014 sysload=0.20 cputime=3425.500 memavail=1401452 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=79.2 pwm=0.000
Stats 71054.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4735 bytes_read=21753 bytes_retransmit=9 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999564 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=1566 bytes_read=6909 bytes_retransmit=0 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012365 adj=50014132 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2189 bytes_read=17999 bytes_retransmit=9 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999381 adj=63999498 Octopus_V1.1_F446: temp=28.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1070 bytes_read=42536 bytes_retransmit=0 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999596 coil_temp=36.6 refs=0 mcu_temp=35.08 supply_voltage=3.014 sysload=0.18 cputime=3425.556 memavail=1401452 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=78.6 pwm=0.000
Stats 71055.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4741 bytes_read=21856 bytes_retransmit=9 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999564 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=1572 bytes_read=6925 bytes_retransmit=0 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012396 adj=50014207 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2195 bytes_read=18113 bytes_retransmit=9 bytes_invalid=0 send_seq=274 receive_seq=274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999380 adj=63999488 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1076 bytes_read=42892 bytes_retransmit=0 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999609 coil_temp=36.6 refs=0 mcu_temp=35.08 supply_voltage=3.014 sysload=0.18 cputime=3425.610 memavail=1401460 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=78.3 pwm=0.000
Stats 71056.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4747 bytes_read=22002 bytes_retransmit=9 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999564 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=1578 bytes_read=6941 bytes_retransmit=0 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012427 adj=50014233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2201 bytes_read=18213 bytes_retransmit=9 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999379 adj=63999493 Octopus_V1.1_F446: temp=28.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.6  heater_bed: target=0 temp=48.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1082 bytes_read=43248 bytes_retransmit=0 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999591 adj=31999623 coil_temp=36.6 refs=0 mcu_temp=35.08 supply_voltage=3.014 sysload=0.18 cputime=3425.664 memavail=1401468 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=78.0 pwm=0.000
Stats 71057.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4753 bytes_read=22105 bytes_retransmit=9 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999563 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=1584 bytes_read=6957 bytes_retransmit=0 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012457 adj=50014263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2207 bytes_read=18327 bytes_retransmit=9 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999494 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1088 bytes_read=43604 bytes_retransmit=0 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999591 adj=31999640 coil_temp=36.6 refs=0 mcu_temp=35.10 supply_voltage=3.014 sysload=0.18 cputime=3425.719 memavail=1401468 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=77.7 pwm=0.000
Stats 71058.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4759 bytes_read=22208 bytes_retransmit=9 bytes_invalid=0 send_seq=454 receive_seq=454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999562 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000021 bytes_write=1590 bytes_read=6973 bytes_retransmit=0 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012485 adj=50014282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2213 bytes_read=18441 bytes_retransmit=9 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999493 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1094 bytes_read=43960 bytes_retransmit=0 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999592 adj=31999655 coil_temp=36.6 refs=0 mcu_temp=35.11 supply_voltage=3.014 sysload=0.18 cputime=3425.774 memavail=1401224 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=77.1 pwm=0.000
Stats 71059.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4765 bytes_read=22340 bytes_retransmit=9 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=1596 bytes_read=7002 bytes_retransmit=0 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012510 adj=50014274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2219 bytes_read=18555 bytes_retransmit=9 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999378 adj=63999502 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=48.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1100 bytes_read=44316 bytes_retransmit=0 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999591 adj=31999667 coil_temp=36.6 refs=0 mcu_temp=35.12 supply_voltage=3.014 sysload=0.17 cputime=3425.830 memavail=1401220 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=76.8 pwm=0.000
Stats 71060.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4771 bytes_read=22443 bytes_retransmit=9 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=1602 bytes_read=7018 bytes_retransmit=0 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012536 adj=50014180 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2225 bytes_read=18669 bytes_retransmit=9 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999441 Octopus_V1.1_F446: temp=28.5 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1106 bytes_read=44665 bytes_retransmit=0 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999624 coil_temp=36.6 refs=0 mcu_temp=35.14 supply_voltage=3.014 sysload=0.17 cputime=3425.886 memavail=1401220 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=76.4 pwm=0.000
Stats 71061.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4777 bytes_read=22560 bytes_retransmit=9 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999575 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=1608 bytes_read=7034 bytes_retransmit=0 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012561 adj=50014167 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2231 bytes_read=18777 bytes_retransmit=9 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999452 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1112 bytes_read=45010 bytes_retransmit=0 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999622 coil_temp=36.6 refs=0 mcu_temp=35.15 supply_voltage=3.014 sysload=0.17 cputime=3425.940 memavail=1401220 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=76.1 pwm=0.000
Stats 71062.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4783 bytes_read=22692 bytes_retransmit=9 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=1614 bytes_read=7050 bytes_retransmit=0 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012587 adj=50014177 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2237 bytes_read=18870 bytes_retransmit=9 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999377 adj=63999464 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1118 bytes_read=45354 bytes_retransmit=0 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999590 adj=31999634 coil_temp=36.7 refs=0 mcu_temp=35.17 supply_voltage=3.014 sysload=0.17 cputime=3425.991 memavail=1400716 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=75.8 pwm=0.000
Stats 71063.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4789 bytes_read=22795 bytes_retransmit=9 bytes_invalid=0 send_seq=459 receive_seq=459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999573 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=1620 bytes_read=7066 bytes_retransmit=0 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012609 adj=50014181 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2243 bytes_read=18976 bytes_retransmit=9 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999374 adj=63999476 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1124 bytes_read=45699 bytes_retransmit=0 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999588 adj=31999637 coil_temp=36.7 refs=0 mcu_temp=35.18 supply_voltage=3.014 sysload=0.17 cputime=3426.014 memavail=1401228 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=75.4 pwm=0.000
Stats 71064.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4795 bytes_read=22898 bytes_retransmit=9 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999568 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000016 bytes_write=1626 bytes_read=7095 bytes_retransmit=0 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012629 adj=50014149 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2249 bytes_read=19096 bytes_retransmit=9 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999373 adj=63999468 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1130 bytes_read=46044 bytes_retransmit=0 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999586 adj=31999622 coil_temp=36.7 refs=0 mcu_temp=35.18 supply_voltage=3.014 sysload=0.16 cputime=3426.038 memavail=1401704 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=74.9 pwm=0.000
Stats 71065.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4801 bytes_read=23030 bytes_retransmit=9 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999561 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000016 bytes_write=1632 bytes_read=7111 bytes_retransmit=0 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012649 adj=50014128 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2255 bytes_read=19193 bytes_retransmit=9 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999485 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1136 bytes_read=46389 bytes_retransmit=0 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999584 adj=31999618 coil_temp=36.7 refs=0 mcu_temp=35.19 supply_voltage=3.014 sysload=0.16 cputime=3426.061 memavail=1401760 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=74.6 pwm=0.000
Stats 71066.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4813 bytes_read=23163 bytes_retransmit=9 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999556 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000016 bytes_write=1638 bytes_read=7127 bytes_retransmit=0 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012670 adj=50014111 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2267 bytes_read=19323 bytes_retransmit=9 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999504 Octopus_V1.1_F446: temp=28.4 EBB42_v1.2_T0: temp=34.9 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1142 bytes_read=46734 bytes_retransmit=0 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999584 adj=31999625 coil_temp=36.7 refs=0 mcu_temp=35.20 supply_voltage=3.014 sysload=0.16 cputime=3426.085 memavail=1401260 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=74.2 pwm=0.000
Stats 71067.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4819 bytes_read=23266 bytes_retransmit=9 bytes_invalid=0 send_seq=464 receive_seq=464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999551 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000016 bytes_write=1644 bytes_read=7143 bytes_retransmit=0 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012691 adj=50014108 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2273 bytes_read=19437 bytes_retransmit=9 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999367 adj=63999499 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1148 bytes_read=47079 bytes_retransmit=0 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999582 adj=31999642 coil_temp=36.7 refs=0 mcu_temp=35.20 supply_voltage=3.014 sysload=0.16 cputime=3426.109 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=73.9 pwm=0.000
Stats 71068.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4825 bytes_read=23398 bytes_retransmit=9 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999554 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000016 bytes_write=1656 bytes_read=7175 bytes_retransmit=0 bytes_invalid=0 send_seq=250 receive_seq=250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012745 adj=50014110 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2279 bytes_read=19537 bytes_retransmit=9 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999515 Octopus_V1.1_F446: temp=28.2 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1154 bytes_read=47427 bytes_retransmit=0 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999668 coil_temp=36.7 refs=0 mcu_temp=35.21 supply_voltage=3.014 sysload=0.16 cputime=3426.163 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=73.5 pwm=0.000
Stats 71069.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4831 bytes_read=23501 bytes_retransmit=9 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999555 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=1662 bytes_read=7204 bytes_retransmit=0 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012770 adj=50014591 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2285 bytes_read=19665 bytes_retransmit=9 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999512 Octopus_V1.1_F446: temp=28.1 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1160 bytes_read=47783 bytes_retransmit=0 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999648 coil_temp=36.7 refs=0 mcu_temp=35.22 supply_voltage=3.014 sysload=0.14 cputime=3426.217 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=73.2 pwm=0.000
Stats 71070.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4837 bytes_read=23604 bytes_retransmit=9 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999557 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=1668 bytes_read=7220 bytes_retransmit=0 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012793 adj=50014520 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2291 bytes_read=19779 bytes_retransmit=9 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999517 Octopus_V1.1_F446: temp=28.1 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1166 bytes_read=48139 bytes_retransmit=0 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999640 coil_temp=36.7 refs=0 mcu_temp=35.23 supply_voltage=3.014 sysload=0.14 cputime=3426.272 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=73.0 pwm=0.000
Stats 71071.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4843 bytes_read=23750 bytes_retransmit=9 bytes_invalid=0 send_seq=468 receive_seq=468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999559 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=1674 bytes_read=7236 bytes_retransmit=0 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012816 adj=50014454 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2297 bytes_read=19879 bytes_retransmit=9 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999517 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1172 bytes_read=48495 bytes_retransmit=0 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999638 coil_temp=36.7 refs=0 mcu_temp=35.25 supply_voltage=3.014 sysload=0.14 cputime=3426.328 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=72.6 pwm=0.000
Stats 71072.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4849 bytes_read=23846 bytes_retransmit=9 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999561 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=1680 bytes_read=7252 bytes_retransmit=0 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012838 adj=50014401 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2303 bytes_read=19993 bytes_retransmit=9 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999513 Octopus_V1.1_F446: temp=28.1 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1178 bytes_read=48835 bytes_retransmit=0 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999640 coil_temp=36.7 refs=0 mcu_temp=35.26 supply_voltage=3.014 sysload=0.14 cputime=3426.381 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=72.3 pwm=0.000
Stats 71073.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4855 bytes_read=23945 bytes_retransmit=9 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999562 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=1686 bytes_read=7268 bytes_retransmit=0 bytes_invalid=0 send_seq=255 receive_seq=255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012862 adj=50014362 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2309 bytes_read=20107 bytes_retransmit=9 bytes_invalid=0 send_seq=293 receive_seq=293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999510 Octopus_V1.1_F446: temp=28.1 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1184 bytes_read=49191 bytes_retransmit=0 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999641 coil_temp=36.7 refs=0 mcu_temp=35.26 supply_voltage=3.014 sysload=0.14 cputime=3426.434 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=71.8 pwm=0.000
Stats 71074.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4861 bytes_read=24077 bytes_retransmit=9 bytes_invalid=0 send_seq=471 receive_seq=471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999565 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1692 bytes_read=7297 bytes_retransmit=0 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012886 adj=50014365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2315 bytes_read=20221 bytes_retransmit=9 bytes_invalid=0 send_seq=294 receive_seq=294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999511 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1190 bytes_read=49547 bytes_retransmit=0 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999647 coil_temp=36.7 refs=0 mcu_temp=35.27 supply_voltage=3.014 sysload=0.13 cputime=3426.489 memavail=1401264 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=71.5 pwm=0.000
Stats 71075.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4867 bytes_read=24180 bytes_retransmit=9 bytes_invalid=0 send_seq=472 receive_seq=472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999567 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1698 bytes_read=7313 bytes_retransmit=0 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012907 adj=50014372 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2321 bytes_read=20335 bytes_retransmit=9 bytes_invalid=0 send_seq=295 receive_seq=295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999505 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.1  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1196 bytes_read=49903 bytes_retransmit=0 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999644 coil_temp=36.7 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.13 cputime=3426.542 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=71.2 pwm=0.000
Stats 71076.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4873 bytes_read=24297 bytes_retransmit=9 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999569 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1704 bytes_read=7329 bytes_retransmit=0 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012917 adj=50014340 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2327 bytes_read=20449 bytes_retransmit=9 bytes_invalid=0 send_seq=296 receive_seq=296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999495 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=48.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1202 bytes_read=50259 bytes_retransmit=0 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999586 adj=31999643 coil_temp=36.7 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.13 cputime=3426.596 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.9 pwm=0.000
Stats 71077.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4879 bytes_read=24429 bytes_retransmit=9 bytes_invalid=0 send_seq=474 receive_seq=474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999571 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1710 bytes_read=7345 bytes_retransmit=0 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012884 adj=50014153 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2333 bytes_read=20549 bytes_retransmit=9 bytes_invalid=0 send_seq=297 receive_seq=297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999496 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=35.1 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1208 bytes_read=50615 bytes_retransmit=0 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999585 adj=31999718 coil_temp=36.7 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.13 cputime=3426.647 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.5 pwm=0.000
Stats 71078.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4885 bytes_read=24532 bytes_retransmit=9 bytes_invalid=0 send_seq=475 receive_seq=475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999577 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1716 bytes_read=7361 bytes_retransmit=0 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012813 adj=50013365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2339 bytes_read=20663 bytes_retransmit=9 bytes_invalid=0 send_seq=298 receive_seq=298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999488 Octopus_V1.1_F446: temp=27.9 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1214 bytes_read=50971 bytes_retransmit=0 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999585 adj=31999685 coil_temp=36.8 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.13 cputime=3426.699 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.1 pwm=0.000
Stats 71079.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4891 bytes_read=24635 bytes_retransmit=9 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999578 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000019 bytes_write=1722 bytes_read=7390 bytes_retransmit=0 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012706 adj=50012173 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2345 bytes_read=20791 bytes_retransmit=9 bytes_invalid=0 send_seq=299 receive_seq=299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999476 Octopus_V1.1_F446: temp=28.0 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1220 bytes_read=51327 bytes_retransmit=0 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999583 adj=31999657 coil_temp=36.8 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.12 cputime=3426.754 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.9 pwm=0.000
Stats 71080.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4897 bytes_read=24767 bytes_retransmit=9 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999574 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000019 bytes_write=1728 bytes_read=7406 bytes_retransmit=0 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012564 adj=50010744 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2351 bytes_read=20891 bytes_retransmit=9 bytes_invalid=0 send_seq=300 receive_seq=300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999492 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1226 bytes_read=51683 bytes_retransmit=0 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999583 adj=31999634 coil_temp=36.8 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.12 cputime=3426.789 memavail=1403316 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.5 pwm=0.000
Stats 71081.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4903 bytes_read=24884 bytes_retransmit=9 bytes_invalid=0 send_seq=478 receive_seq=478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999569 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000019 bytes_write=1734 bytes_read=7422 bytes_retransmit=0 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012395 adj=50009142 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2357 bytes_read=21005 bytes_retransmit=9 bytes_invalid=0 send_seq=301 receive_seq=301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999516 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1232 bytes_read=52039 bytes_retransmit=0 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999641 coil_temp=36.8 refs=0 mcu_temp=35.28 supply_voltage=3.014 sysload=0.12 cputime=3426.812 memavail=1403316 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.2 pwm=0.000
Stats 71082.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4909 bytes_read=24987 bytes_retransmit=9 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999564 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000019 bytes_write=1740 bytes_read=7438 bytes_retransmit=0 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50012197 adj=50007485 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2363 bytes_read=21119 bytes_retransmit=9 bytes_invalid=0 send_seq=302 receive_seq=302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999529 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1238 bytes_read=52395 bytes_retransmit=0 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999579 adj=31999628 coil_temp=36.8 refs=0 mcu_temp=35.29 supply_voltage=3.014 sysload=0.12 cputime=3426.835 memavail=1403316 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.6 pwm=0.000
Stats 71083.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4915 bytes_read=25119 bytes_retransmit=9 bytes_invalid=0 send_seq=480 receive_seq=480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999560 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000019 bytes_write=1746 bytes_read=7454 bytes_retransmit=0 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011975 adj=50005765 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2369 bytes_read=21219 bytes_retransmit=9 bytes_invalid=0 send_seq=303 receive_seq=303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999553 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1244 bytes_read=52751 bytes_retransmit=0 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999577 adj=31999617 coil_temp=36.8 refs=0 mcu_temp=35.29 supply_voltage=3.014 sysload=0.12 cputime=3426.859 memavail=1402300 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.6 pwm=0.000
Stats 71084.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4921 bytes_read=25222 bytes_retransmit=9 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999557 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1752 bytes_read=7483 bytes_retransmit=0 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011733 adj=50004064 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2375 bytes_read=21347 bytes_retransmit=9 bytes_invalid=0 send_seq=304 receive_seq=304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999366 adj=63999542 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1250 bytes_read=53107 bytes_retransmit=0 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999575 adj=31999611 coil_temp=36.8 refs=0 mcu_temp=35.29 supply_voltage=3.014 sysload=0.11 cputime=3426.882 memavail=1405976 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.4 pwm=0.000
Stats 71085.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4927 bytes_read=25325 bytes_retransmit=9 bytes_invalid=0 send_seq=482 receive_seq=482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999561 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1758 bytes_read=7499 bytes_retransmit=0 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011478 adj=50002410 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2381 bytes_read=21461 bytes_retransmit=9 bytes_invalid=0 send_seq=305 receive_seq=305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999523 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.6  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1256 bytes_read=53463 bytes_retransmit=0 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999603 coil_temp=36.8 refs=0 mcu_temp=35.31 supply_voltage=3.014 sysload=0.11 cputime=3426.927 memavail=1405976 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.9 pwm=0.000
Stats 71086.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4933 bytes_read=25471 bytes_retransmit=9 bytes_invalid=0 send_seq=483 receive_seq=483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999565 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1764 bytes_read=7515 bytes_retransmit=0 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50011206 adj=50000892 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2387 bytes_read=21561 bytes_retransmit=9 bytes_invalid=0 send_seq=306 receive_seq=306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999555 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1262 bytes_read=53819 bytes_retransmit=0 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999646 coil_temp=36.8 refs=0 mcu_temp=35.31 supply_voltage=3.014 sysload=0.11 cputime=3426.980 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.7 pwm=0.000
Stats 71087.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4939 bytes_read=25574 bytes_retransmit=9 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999568 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1770 bytes_read=7531 bytes_retransmit=0 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010919 adj=49999417 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2393 bytes_read=21675 bytes_retransmit=9 bytes_invalid=0 send_seq=307 receive_seq=307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999525 Octopus_V1.1_F446: temp=27.8 EBB42_v1.2_T0: temp=35.0 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1268 bytes_read=54175 bytes_retransmit=0 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999637 coil_temp=36.8 refs=0 mcu_temp=35.32 supply_voltage=3.014 sysload=0.11 cputime=3427.033 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.5 pwm=0.000
Stats 71088.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4945 bytes_read=25677 bytes_retransmit=9 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999571 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000012 bytes_write=1776 bytes_read=7547 bytes_retransmit=0 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010620 adj=49998019 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2399 bytes_read=21789 bytes_retransmit=9 bytes_invalid=0 send_seq=308 receive_seq=308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999371 adj=63999538 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1280 bytes_read=54547 bytes_retransmit=0 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999579 adj=31999636 coil_temp=36.8 refs=0 mcu_temp=35.32 supply_voltage=3.014 sysload=0.11 cputime=3427.086 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.0 pwm=0.000
Stats 71089.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4951 bytes_read=25809 bytes_retransmit=9 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999572 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=1782 bytes_read=7576 bytes_retransmit=0 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50010309 adj=49996706 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2405 bytes_read=21889 bytes_retransmit=9 bytes_invalid=0 send_seq=309 receive_seq=309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999512 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1286 bytes_read=54903 bytes_retransmit=0 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999657 coil_temp=36.8 refs=0 mcu_temp=35.34 supply_voltage=3.014 sysload=0.10 cputime=3427.139 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=66.8 pwm=0.000
Stats 71090.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4957 bytes_read=25912 bytes_retransmit=9 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999575 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=1788 bytes_read=7592 bytes_retransmit=0 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009986 adj=49995472 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2411 bytes_read=22017 bytes_retransmit=9 bytes_invalid=0 send_seq=310 receive_seq=310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999503 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1292 bytes_read=55259 bytes_retransmit=0 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999676 coil_temp=36.8 refs=0 mcu_temp=35.33 supply_voltage=3.014 sysload=0.10 cputime=3427.193 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=66.5 pwm=0.000
Stats 71091.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4963 bytes_read=26029 bytes_retransmit=9 bytes_invalid=0 send_seq=488 receive_seq=488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=1794 bytes_read=7608 bytes_retransmit=0 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009656 adj=49994274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2417 bytes_read=22131 bytes_retransmit=9 bytes_invalid=0 send_seq=311 receive_seq=311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999484 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1298 bytes_read=55615 bytes_retransmit=0 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999579 adj=31999652 coil_temp=36.8 refs=0 mcu_temp=35.33 supply_voltage=3.014 sysload=0.10 cputime=3427.245 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=66.1 pwm=0.000
Stats 71092.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4969 bytes_read=26161 bytes_retransmit=9 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999580 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=1800 bytes_read=7624 bytes_retransmit=0 bytes_invalid=0 send_seq=274 receive_seq=274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50009320 adj=49993183 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2423 bytes_read=22231 bytes_retransmit=9 bytes_invalid=0 send_seq=312 receive_seq=312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999477 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1304 bytes_read=55971 bytes_retransmit=0 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999636 coil_temp=36.8 refs=0 mcu_temp=35.34 supply_voltage=3.014 sysload=0.10 cputime=3427.298 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=65.9 pwm=0.000
Stats 71093.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4975 bytes_read=26264 bytes_retransmit=9 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999584 rpi: mcu_awake=0.001 mcu_task_avg=0.000018 mcu_task_stddev=0.000019 bytes_write=1806 bytes_read=7640 bytes_retransmit=0 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008980 adj=49992187 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2429 bytes_read=22345 bytes_retransmit=9 bytes_invalid=0 send_seq=313 receive_seq=313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999370 adj=63999484 Octopus_V1.1_F446: temp=27.7 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1310 bytes_read=56327 bytes_retransmit=0 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999579 adj=31999642 coil_temp=36.8 refs=0 mcu_temp=35.34 supply_voltage=3.014 sysload=0.10 cputime=3427.350 memavail=1405772 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=65.7 pwm=0.000
Stats 71094.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4981 bytes_read=26367 bytes_retransmit=9 bytes_invalid=0 send_seq=491 receive_seq=491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999584 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=1812 bytes_read=7669 bytes_retransmit=0 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008637 adj=49991286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2435 bytes_read=22459 bytes_retransmit=9 bytes_invalid=0 send_seq=314 receive_seq=314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999463 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1316 bytes_read=56683 bytes_retransmit=0 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999625 coil_temp=36.8 refs=0 mcu_temp=35.35 supply_voltage=3.014 sysload=0.09 cputime=3427.401 memavail=1405028 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=65.4 pwm=0.000
Stats 71095.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4987 bytes_read=26497 bytes_retransmit=9 bytes_invalid=0 send_seq=492 receive_seq=492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999587 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=1818 bytes_read=7685 bytes_retransmit=0 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50008292 adj=49990491 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2441 bytes_read=22573 bytes_retransmit=9 bytes_invalid=0 send_seq=315 receive_seq=315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999368 adj=63999463 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1322 bytes_read=57039 bytes_retransmit=0 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999581 adj=31999643 coil_temp=36.8 refs=0 mcu_temp=35.35 supply_voltage=3.014 sysload=0.09 cputime=3427.453 memavail=1404540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=65.0 pwm=0.000
Stats 71096.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4993 bytes_read=26607 bytes_retransmit=9 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999589 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=1824 bytes_read=7701 bytes_retransmit=0 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007941 adj=49989751 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2447 bytes_read=22687 bytes_retransmit=9 bytes_invalid=0 send_seq=316 receive_seq=316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999369 adj=63999450 Octopus_V1.1_F446: temp=27.6 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1328 bytes_read=57395 bytes_retransmit=0 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999582 adj=31999654 coil_temp=36.8 refs=0 mcu_temp=35.36 supply_voltage=3.014 sysload=0.09 cputime=3427.507 memavail=1404540 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=64.5 pwm=0.000
Stats 71097.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4999 bytes_read=26721 bytes_retransmit=9 bytes_invalid=0 send_seq=494 receive_seq=494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999591 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=1830 bytes_read=7717 bytes_retransmit=0 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007590 adj=49989033 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2453 bytes_read=22801 bytes_retransmit=9 bytes_invalid=0 send_seq=317 receive_seq=317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999367 adj=63999461 Octopus_V1.1_F446: temp=27.4 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1334 bytes_read=57751 bytes_retransmit=0 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999580 adj=31999659 coil_temp=36.8 refs=0 mcu_temp=35.37 supply_voltage=3.014 sysload=0.09 cputime=3427.547 memavail=1403432 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=64.6 pwm=0.000
Stats 71098.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5005 bytes_read=26839 bytes_retransmit=9 bytes_invalid=0 send_seq=495 receive_seq=495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999587 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=1836 bytes_read=7733 bytes_retransmit=0 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50007233 adj=49988400 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2459 bytes_read=22901 bytes_retransmit=9 bytes_invalid=0 send_seq=318 receive_seq=318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999366 adj=63999446 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1340 bytes_read=58107 bytes_retransmit=0 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999578 adj=31999630 coil_temp=36.8 refs=0 mcu_temp=35.38 supply_voltage=3.014 sysload=0.09 cputime=3427.570 memavail=1403304 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=64.3 pwm=0.000
Stats 71099.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5011 bytes_read=26942 bytes_retransmit=9 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999583 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000020 bytes_write=1842 bytes_read=7761 bytes_retransmit=0 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006878 adj=49987765 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2465 bytes_read=23029 bytes_retransmit=9 bytes_invalid=0 send_seq=319 receive_seq=319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999365 adj=63999465 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1346 bytes_read=58463 bytes_retransmit=0 bytes_invalid=0 send_seq=223 receive_seq=223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999576 adj=31999616 coil_temp=36.9 refs=0 mcu_temp=35.38 supply_voltage=3.014 sysload=0.09 cputime=3427.593 memavail=1403304 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=64.0 pwm=0.000
Stats 71100.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5017 bytes_read=27059 bytes_retransmit=9 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999579 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000020 bytes_write=1848 bytes_read=7776 bytes_retransmit=0 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006527 adj=49987222 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2471 bytes_read=23143 bytes_retransmit=9 bytes_invalid=0 send_seq=320 receive_seq=320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999474 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1352 bytes_read=58819 bytes_retransmit=0 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999575 adj=31999607 coil_temp=36.9 refs=0 mcu_temp=35.39 supply_voltage=3.014 sysload=0.09 cputime=3427.617 memavail=1402800 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=63.6 pwm=0.000
Stats 71101.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5023 bytes_read=27191 bytes_retransmit=9 bytes_invalid=0 send_seq=498 receive_seq=498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000020 bytes_write=1854 bytes_read=7791 bytes_retransmit=0 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50006176 adj=49986782 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2477 bytes_read=23243 bytes_retransmit=9 bytes_invalid=0 send_seq=321 receive_seq=321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999484 Octopus_V1.1_F446: temp=27.5 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1358 bytes_read=59175 bytes_retransmit=0 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999573 adj=31999601 coil_temp=36.9 refs=0 mcu_temp=35.39 supply_voltage=3.014 sysload=0.09 cputime=3427.641 memavail=1402804 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=63.6 pwm=0.000
Stats 71102.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5029 bytes_read=27294 bytes_retransmit=9 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999574 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000020 bytes_write=1860 bytes_read=7806 bytes_retransmit=0 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005827 adj=49986352 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2483 bytes_read=23371 bytes_retransmit=9 bytes_invalid=0 send_seq=322 receive_seq=322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999497 Octopus_V1.1_F446: temp=27.4 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1364 bytes_read=59531 bytes_retransmit=0 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999594 coil_temp=36.9 refs=0 mcu_temp=35.40 supply_voltage=3.014 sysload=0.09 cputime=3427.677 memavail=1402804 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=63.1 pwm=0.000
Stats 71103.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5035 bytes_read=27411 bytes_retransmit=9 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999576 rpi: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000020 bytes_write=1866 bytes_read=7821 bytes_retransmit=0 bytes_invalid=0 send_seq=285 receive_seq=285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005485 adj=49985973 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2489 bytes_read=23471 bytes_retransmit=9 bytes_invalid=0 send_seq=323 receive_seq=323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999486 Octopus_V1.1_F446: temp=27.4 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1370 bytes_read=59887 bytes_retransmit=0 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999604 coil_temp=36.9 refs=0 mcu_temp=35.40 supply_voltage=3.014 sysload=0.09 cputime=3427.729 memavail=1402804 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=62.8 pwm=0.000
Stats 71104.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5041 bytes_read=27529 bytes_retransmit=9 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999581 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=1872 bytes_read=7850 bytes_retransmit=0 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50005149 adj=49985694 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2495 bytes_read=23571 bytes_retransmit=9 bytes_invalid=0 send_seq=324 receive_seq=324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999485 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1376 bytes_read=60243 bytes_retransmit=0 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999601 coil_temp=36.9 refs=0 mcu_temp=35.40 supply_voltage=3.014 sysload=0.16 cputime=3427.780 memavail=1402048 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=62.6 pwm=0.000
Stats 71105.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5047 bytes_read=27632 bytes_retransmit=9 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999583 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=1878 bytes_read=7866 bytes_retransmit=0 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004819 adj=49985461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2501 bytes_read=23713 bytes_retransmit=9 bytes_invalid=0 send_seq=325 receive_seq=325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999473 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1382 bytes_read=60599 bytes_retransmit=0 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999597 coil_temp=36.9 refs=0 mcu_temp=35.41 supply_voltage=3.014 sysload=0.16 cputime=3427.835 memavail=1402048 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=62.3 pwm=0.000
Stats 71106.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5053 bytes_read=27763 bytes_retransmit=9 bytes_invalid=0 send_seq=503 receive_seq=503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999588 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=1884 bytes_read=7882 bytes_retransmit=0 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004492 adj=49985318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2507 bytes_read=23813 bytes_retransmit=9 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999469 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1388 bytes_read=60955 bytes_retransmit=0 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999573 adj=31999610 coil_temp=36.9 refs=0 mcu_temp=35.42 supply_voltage=3.014 sysload=0.16 cputime=3427.888 memavail=1402052 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=62.1 pwm=0.000
Stats 71107.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5059 bytes_read=27881 bytes_retransmit=9 bytes_invalid=0 send_seq=504 receive_seq=504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999592 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=1890 bytes_read=7898 bytes_retransmit=0 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50004171 adj=49985151 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2513 bytes_read=23913 bytes_retransmit=9 bytes_invalid=0 send_seq=327 receive_seq=327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999466 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1394 bytes_read=61311 bytes_retransmit=0 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999573 adj=31999624 coil_temp=36.9 refs=0 mcu_temp=35.43 supply_voltage=3.014 sysload=0.16 cputime=3427.942 memavail=1402052 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=61.9 pwm=0.000
Stats 71108.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5065 bytes_read=27984 bytes_retransmit=9 bytes_invalid=0 send_seq=505 receive_seq=505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999595 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=1896 bytes_read=7914 bytes_retransmit=0 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50003856 adj=49985037 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2519 bytes_read=24041 bytes_retransmit=9 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999459 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1400 bytes_read=61667 bytes_retransmit=0 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999612 coil_temp=36.9 refs=0 mcu_temp=35.44 supply_voltage=3.014 sysload=0.16 cputime=3427.996 memavail=1402052 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=61.8 pwm=0.000
Stats 71109.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5071 bytes_read=28101 bytes_retransmit=9 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999598 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1902 bytes_read=7943 bytes_retransmit=0 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50003549 adj=49984953 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2525 bytes_read=24141 bytes_retransmit=9 bytes_invalid=0 send_seq=329 receive_seq=329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999458 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1406 bytes_read=62023 bytes_retransmit=0 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999572 adj=31999596 coil_temp=36.9 refs=0 mcu_temp=35.45 supply_voltage=3.014 sysload=0.15 cputime=3428.050 memavail=1402068 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=61.3 pwm=0.000
Stats 71110.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5077 bytes_read=28219 bytes_retransmit=9 bytes_invalid=0 send_seq=507 receive_seq=507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999600 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1908 bytes_read=7959 bytes_retransmit=0 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50003244 adj=49984957 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2531 bytes_read=24255 bytes_retransmit=9 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999461 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1412 bytes_read=62379 bytes_retransmit=0 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999600 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.15 cputime=3428.103 memavail=1402068 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=61.2 pwm=0.000
Stats 71111.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5083 bytes_read=28322 bytes_retransmit=9 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999604 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1914 bytes_read=7975 bytes_retransmit=0 bytes_invalid=0 send_seq=293 receive_seq=293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50002945 adj=49984904 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2537 bytes_read=24383 bytes_retransmit=9 bytes_invalid=0 send_seq=331 receive_seq=331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999457 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1418 bytes_read=62735 bytes_retransmit=0 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999571 adj=31999595 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.15 cputime=3428.158 memavail=1402068 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=60.8 pwm=0.000
Stats 71112.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5089 bytes_read=28453 bytes_retransmit=9 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999606 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1920 bytes_read=7991 bytes_retransmit=0 bytes_invalid=0 send_seq=294 receive_seq=294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50002655 adj=49984870 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2543 bytes_read=24483 bytes_retransmit=9 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999453 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1424 bytes_read=63091 bytes_retransmit=0 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999570 adj=31999591 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.15 cputime=3428.211 memavail=1402068 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=60.7 pwm=0.000
Stats 71113.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5095 bytes_read=28571 bytes_retransmit=9 bytes_invalid=0 send_seq=510 receive_seq=510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1926 bytes_read=8007 bytes_retransmit=0 bytes_invalid=0 send_seq=295 receive_seq=295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50002372 adj=49984902 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2549 bytes_read=24583 bytes_retransmit=9 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999364 adj=63999454 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1430 bytes_read=63447 bytes_retransmit=0 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999594 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.15 cputime=3428.265 memavail=1402076 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=60.4 pwm=0.000
Stats 71114.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5101 bytes_read=28674 bytes_retransmit=9 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999610 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1932 bytes_read=8023 bytes_retransmit=0 bytes_invalid=0 send_seq=296 receive_seq=296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50002096 adj=49984968 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2555 bytes_read=24711 bytes_retransmit=9 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999364 adj=63999464 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=31.6  heater_bed: target=0 temp=47.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1436 bytes_read=63803 bytes_retransmit=0 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999569 adj=31999583 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.13 cputime=3428.316 memavail=1395564 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=60.1 pwm=0.000
Stats 71115.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5107 bytes_read=28791 bytes_retransmit=9 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1938 bytes_read=8052 bytes_retransmit=0 bytes_invalid=0 send_seq=297 receive_seq=297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50001822 adj=49985055 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2561 bytes_read=24825 bytes_retransmit=9 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999468 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1442 bytes_read=64159 bytes_retransmit=0 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999567 adj=31999579 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.13 cputime=3428.340 memavail=1401360 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=59.8 pwm=0.000
Stats 71116.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5113 bytes_read=28909 bytes_retransmit=9 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999604 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1944 bytes_read=8068 bytes_retransmit=0 bytes_invalid=0 send_seq=298 receive_seq=298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50001553 adj=49985088 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2567 bytes_read=24925 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999360 adj=63999457 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1448 bytes_read=64515 bytes_retransmit=0 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999565 adj=31999566 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.13 cputime=3428.364 memavail=1401360 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=59.7 pwm=0.000
Stats 71117.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5119 bytes_read=29026 bytes_retransmit=9 bytes_invalid=0 send_seq=514 receive_seq=514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999600 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1950 bytes_read=8084 bytes_retransmit=0 bytes_invalid=0 send_seq=299 receive_seq=299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50001293 adj=49985153 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2573 bytes_read=25053 bytes_retransmit=9 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999464 Octopus_V1.1_F446: temp=27.3 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1454 bytes_read=64871 bytes_retransmit=0 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999563 adj=31999572 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.13 cputime=3428.387 memavail=1401364 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=59.3 pwm=0.000
Stats 71118.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5125 bytes_read=29143 bytes_retransmit=9 bytes_invalid=0 send_seq=515 receive_seq=515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999597 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1956 bytes_read=8100 bytes_retransmit=0 bytes_invalid=0 send_seq=300 receive_seq=300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50001041 adj=49985251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2579 bytes_read=25153 bytes_retransmit=9 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999471 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=35.0  heater_bed: target=0 temp=47.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1460 bytes_read=65227 bytes_retransmit=0 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999562 adj=31999573 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.13 cputime=3428.411 memavail=1401364 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=59.2 pwm=0.000
Stats 71119.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5131 bytes_read=29259 bytes_retransmit=9 bytes_invalid=0 send_seq=516 receive_seq=516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999599 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000021 bytes_write=1962 bytes_read=8116 bytes_retransmit=0 bytes_invalid=0 send_seq=301 receive_seq=301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000797 adj=49985379 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2585 bytes_read=25253 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999356 adj=63999468 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1466 bytes_read=65583 bytes_retransmit=0 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999561 adj=31999580 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.12 cputime=3428.442 memavail=1401368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=59.1 pwm=0.000
Stats 71120.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5137 bytes_read=29355 bytes_retransmit=9 bytes_invalid=0 send_seq=517 receive_seq=517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999606 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1968 bytes_read=8145 bytes_retransmit=0 bytes_invalid=0 send_seq=302 receive_seq=302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000567 adj=49985518 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2591 bytes_read=25395 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999451 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1472 bytes_read=65939 bytes_retransmit=0 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999568 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.12 cputime=3428.498 memavail=1401368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=58.8 pwm=0.000
Stats 71121.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5143 bytes_read=29484 bytes_retransmit=9 bytes_invalid=0 send_seq=518 receive_seq=518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999609 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1974 bytes_read=8161 bytes_retransmit=0 bytes_invalid=0 send_seq=303 receive_seq=303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000346 adj=49985761 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2597 bytes_read=25495 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999433 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1478 bytes_read=66295 bytes_retransmit=0 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999557 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.12 cputime=3428.553 memavail=1401368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=58.4 pwm=0.000
Stats 71122.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5149 bytes_read=29601 bytes_retransmit=9 bytes_invalid=0 send_seq=519 receive_seq=519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999611 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1980 bytes_read=8177 bytes_retransmit=0 bytes_invalid=0 send_seq=304 receive_seq=304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000135 adj=49986030 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2603 bytes_read=25595 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999442 Octopus_V1.1_F446: temp=27.2 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1484 bytes_read=66651 bytes_retransmit=0 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999565 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.12 cputime=3428.607 memavail=1401368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=58.3 pwm=0.000
Stats 71123.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5155 bytes_read=29704 bytes_retransmit=9 bytes_invalid=0 send_seq=520 receive_seq=520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999611 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1986 bytes_read=8193 bytes_retransmit=0 bytes_invalid=0 send_seq=305 receive_seq=305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999930 adj=49986339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2609 bytes_read=25723 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999360 adj=63999444 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1490 bytes_read=67007 bytes_retransmit=0 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999559 adj=31999567 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.12 cputime=3428.663 memavail=1401368 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=58.1 pwm=0.000
Stats 71124.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5161 bytes_read=29836 bytes_retransmit=9 bytes_invalid=0 send_seq=521 receive_seq=521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999615 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1992 bytes_read=8209 bytes_retransmit=0 bytes_invalid=0 send_seq=306 receive_seq=306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999728 adj=49986605 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2615 bytes_read=25823 bytes_retransmit=9 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999495 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1496 bytes_read=67363 bytes_retransmit=0 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999559 adj=31999579 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.11 cputime=3428.715 memavail=1401104 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=57.6 pwm=0.000
Stats 71125.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5167 bytes_read=29939 bytes_retransmit=9 bytes_invalid=0 send_seq=522 receive_seq=522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999618 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=1998 bytes_read=8238 bytes_retransmit=0 bytes_invalid=0 send_seq=307 receive_seq=307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999535 adj=49986805 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2621 bytes_read=25937 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999504 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1502 bytes_read=67719 bytes_retransmit=0 bytes_invalid=0 send_seq=249 receive_seq=249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999579 coil_temp=36.9 refs=0 mcu_temp=35.48 supply_voltage=3.014 sysload=0.11 cputime=3428.769 memavail=1401156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=57.5 pwm=0.000
Stats 71126.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5173 bytes_read=30042 bytes_retransmit=9 bytes_invalid=0 send_seq=523 receive_seq=523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999622 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2004 bytes_read=8254 bytes_retransmit=0 bytes_invalid=0 send_seq=308 receive_seq=308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999351 adj=49987037 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2627 bytes_read=26065 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999479 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1508 bytes_read=68075 bytes_retransmit=0 bytes_invalid=0 send_seq=250 receive_seq=250 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999561 adj=31999597 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.11 cputime=3428.823 memavail=1401156 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=57.3 pwm=0.000
Stats 71127.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5179 bytes_read=30188 bytes_retransmit=9 bytes_invalid=0 send_seq=524 receive_seq=524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999625 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2010 bytes_read=8270 bytes_retransmit=0 bytes_invalid=0 send_seq=309 receive_seq=309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999174 adj=49987302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2633 bytes_read=26165 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999362 adj=63999472 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1514 bytes_read=68431 bytes_retransmit=0 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999600 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.11 cputime=3428.877 memavail=1400944 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=57.2 pwm=0.000
Stats 71128.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5191 bytes_read=30307 bytes_retransmit=9 bytes_invalid=0 send_seq=526 receive_seq=526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999629 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2016 bytes_read=8286 bytes_retransmit=0 bytes_invalid=0 send_seq=310 receive_seq=310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999003 adj=49987553 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2645 bytes_read=26274 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999463 Octopus_V1.1_F446: temp=27.1 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=32.6  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1520 bytes_read=68787 bytes_retransmit=0 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999593 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.11 cputime=3428.931 memavail=1400944 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=57.1 pwm=0.000
Stats 71129.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5197 bytes_read=30410 bytes_retransmit=9 bytes_invalid=0 send_seq=527 receive_seq=527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999631 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2022 bytes_read=8302 bytes_retransmit=0 bytes_invalid=0 send_seq=311 receive_seq=311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998839 adj=49987791 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2651 bytes_read=26393 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999464 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=31.2  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1526 bytes_read=69143 bytes_retransmit=0 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999591 coil_temp=36.9 refs=0 mcu_temp=35.47 supply_voltage=3.014 sysload=0.10 cputime=3428.985 memavail=1400948 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=56.8 pwm=0.000
Stats 71130.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5203 bytes_read=30542 bytes_retransmit=9 bytes_invalid=0 send_seq=528 receive_seq=528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999635 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2028 bytes_read=8331 bytes_retransmit=0 bytes_invalid=0 send_seq=312 receive_seq=312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998684 adj=49988058 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2657 bytes_read=26500 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999461 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1532 bytes_read=69499 bytes_retransmit=0 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999590 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.10 cputime=3429.038 memavail=1400948 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=56.3 pwm=0.000
Stats 71131.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5209 bytes_read=30645 bytes_retransmit=9 bytes_invalid=0 send_seq=529 receive_seq=529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999635 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2040 bytes_read=8363 bytes_retransmit=0 bytes_invalid=0 send_seq=314 receive_seq=314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998396 adj=49988327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2663 bytes_read=26593 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999453 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1538 bytes_read=69855 bytes_retransmit=0 bytes_invalid=0 send_seq=255 receive_seq=255 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999561 adj=31999596 coil_temp=36.9 refs=0 mcu_temp=35.49 supply_voltage=3.014 sysload=0.10 cputime=3429.093 memavail=1399688 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=56.4 pwm=0.000
Stats 71132.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5215 bytes_read=30762 bytes_retransmit=9 bytes_invalid=0 send_seq=530 receive_seq=530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999633 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2046 bytes_read=8379 bytes_retransmit=0 bytes_invalid=0 send_seq=315 receive_seq=315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998259 adj=49986467 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2669 bytes_read=26719 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999451 Octopus_V1.1_F446: temp=27.0 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=47.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1544 bytes_read=70211 bytes_retransmit=0 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999619 coil_temp=36.9 refs=0 mcu_temp=35.50 supply_voltage=3.014 sysload=0.10 cputime=3429.119 memavail=1401480 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=56.1 pwm=0.000
Stats 71133.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5221 bytes_read=30894 bytes_retransmit=9 bytes_invalid=0 send_seq=531 receive_seq=531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999630 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2052 bytes_read=8395 bytes_retransmit=0 bytes_invalid=0 send_seq=316 receive_seq=316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998129 adj=49987375 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2675 bytes_read=26819 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999447 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1550 bytes_read=70567 bytes_retransmit=0 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999558 adj=31999604 coil_temp=36.9 refs=0 mcu_temp=35.50 supply_voltage=3.014 sysload=0.10 cputime=3429.143 memavail=1401516 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=55.8 pwm=0.000
Stats 71134.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5227 bytes_read=30997 bytes_retransmit=9 bytes_invalid=0 send_seq=532 receive_seq=532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999625 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000022 bytes_write=2058 bytes_read=8411 bytes_retransmit=0 bytes_invalid=0 send_seq=317 receive_seq=317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998007 adj=49988131 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2681 bytes_read=26919 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999453 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1556 bytes_read=70923 bytes_retransmit=0 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999557 adj=31999592 coil_temp=36.9 refs=0 mcu_temp=35.51 supply_voltage=3.014 sysload=0.10 cputime=3429.167 memavail=1400800 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=55.7 pwm=0.000
Stats 71135.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5233 bytes_read=31100 bytes_retransmit=9 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999620 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=2064 bytes_read=8440 bytes_retransmit=0 bytes_invalid=0 send_seq=318 receive_seq=318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997890 adj=49988785 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2687 bytes_read=27061 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999356 adj=63999462 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1562 bytes_read=71279 bytes_retransmit=0 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999556 adj=31999590 coil_temp=36.9 refs=0 mcu_temp=35.52 supply_voltage=3.014 sysload=0.10 cputime=3429.191 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=55.5 pwm=0.000
Stats 71136.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5239 bytes_read=31232 bytes_retransmit=9 bytes_invalid=0 send_seq=534 receive_seq=534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999616 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=2070 bytes_read=8456 bytes_retransmit=0 bytes_invalid=0 send_seq=319 receive_seq=319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997782 adj=49989344 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2693 bytes_read=27161 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999354 adj=63999473 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.2 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1568 bytes_read=71635 bytes_retransmit=0 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999557 adj=31999602 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.10 cputime=3429.215 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=55.1 pwm=0.000
Stats 71137.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5245 bytes_read=31349 bytes_retransmit=9 bytes_invalid=0 send_seq=535 receive_seq=535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999618 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=2076 bytes_read=8472 bytes_retransmit=0 bytes_invalid=0 send_seq=320 receive_seq=320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997685 adj=49989853 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2699 bytes_read=27261 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999356 adj=63999473 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1574 bytes_read=71991 bytes_retransmit=0 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999557 adj=31999633 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.10 cputime=3429.267 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=55.2 pwm=0.000
Stats 71138.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5251 bytes_read=31452 bytes_retransmit=9 bytes_invalid=0 send_seq=536 receive_seq=536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999622 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=2082 bytes_read=8488 bytes_retransmit=0 bytes_invalid=0 send_seq=321 receive_seq=321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997595 adj=49990354 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2705 bytes_read=27389 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999356 adj=63999491 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1580 bytes_read=72347 bytes_retransmit=0 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999558 adj=31999622 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.10 cputime=3429.322 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=54.8 pwm=0.000
Stats 71139.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5257 bytes_read=31584 bytes_retransmit=9 bytes_invalid=0 send_seq=537 receive_seq=537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999626 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000014 bytes_write=2088 bytes_read=8504 bytes_retransmit=0 bytes_invalid=0 send_seq=322 receive_seq=322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997511 adj=49990796 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000010 bytes_write=2711 bytes_read=27489 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999468 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=46.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1586 bytes_read=72703 bytes_retransmit=0 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999558 adj=31999633 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.17 cputime=3429.378 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=54.6 pwm=0.000
Stats 71140.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5263 bytes_read=31687 bytes_retransmit=9 bytes_invalid=0 send_seq=538 receive_seq=538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999626 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000019 bytes_write=2094 bytes_read=8533 bytes_retransmit=0 bytes_invalid=0 send_seq=323 receive_seq=323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997432 adj=49991206 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2717 bytes_read=27603 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999474 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1592 bytes_read=73043 bytes_retransmit=0 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999620 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.17 cputime=3429.431 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=54.5 pwm=0.000
Stats 71141.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5269 bytes_read=31790 bytes_retransmit=9 bytes_invalid=0 send_seq=539 receive_seq=539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999637 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000019 bytes_write=2100 bytes_read=8549 bytes_retransmit=0 bytes_invalid=0 send_seq=324 receive_seq=324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997359 adj=49991588 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2723 bytes_read=27731 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999470 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1598 bytes_read=73399 bytes_retransmit=0 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999562 adj=31999653 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.17 cputime=3429.487 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=54.4 pwm=0.000
Stats 71142.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5275 bytes_read=31936 bytes_retransmit=9 bytes_invalid=0 send_seq=540 receive_seq=540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999639 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000019 bytes_write=2106 bytes_read=8565 bytes_retransmit=0 bytes_invalid=0 send_seq=325 receive_seq=325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997292 adj=49991904 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2729 bytes_read=27831 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999415 Octopus_V1.1_F446: temp=26.9 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1604 bytes_read=73755 bytes_retransmit=0 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999562 adj=31999646 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.17 cputime=3429.544 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=54.1 pwm=0.000
Stats 71143.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5281 bytes_read=32035 bytes_retransmit=9 bytes_invalid=0 send_seq=541 receive_seq=541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999641 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000019 bytes_write=2112 bytes_read=8581 bytes_retransmit=0 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997230 adj=49992234 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2735 bytes_read=27931 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999418 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1610 bytes_read=74111 bytes_retransmit=0 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999561 adj=31999632 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.17 cputime=3429.599 memavail=1400276 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.9 pwm=0.000
Stats 71144.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5287 bytes_read=32131 bytes_retransmit=9 bytes_invalid=0 send_seq=542 receive_seq=542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999645 rpi: mcu_awake=0.001 mcu_task_avg=0.000016 mcu_task_stddev=0.000019 bytes_write=2118 bytes_read=8597 bytes_retransmit=0 bytes_invalid=0 send_seq=327 receive_seq=327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997175 adj=49992571 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2741 bytes_read=28059 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999431 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1616 bytes_read=74467 bytes_retransmit=0 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999561 adj=31999617 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.15 cputime=3429.653 memavail=1400292 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.9 pwm=0.000
Stats 71145.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5293 bytes_read=32263 bytes_retransmit=9 bytes_invalid=0 send_seq=543 receive_seq=543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999647 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=2124 bytes_read=8626 bytes_retransmit=0 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997126 adj=49992887 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2747 bytes_read=28173 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999415 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1622 bytes_read=74823 bytes_retransmit=0 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999593 coil_temp=36.9 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.15 cputime=3429.709 memavail=1400292 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.5 pwm=0.000
Stats 71146.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5299 bytes_read=32366 bytes_retransmit=9 bytes_invalid=0 send_seq=544 receive_seq=544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=2130 bytes_read=8642 bytes_retransmit=0 bytes_invalid=0 send_seq=329 receive_seq=329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997084 adj=49993214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2753 bytes_read=28273 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999421 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1628 bytes_read=75179 bytes_retransmit=0 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999560 adj=31999589 coil_temp=36.9 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.15 cputime=3429.765 memavail=1400548 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.7 pwm=0.000
Stats 71147.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5305 bytes_read=32483 bytes_retransmit=9 bytes_invalid=0 send_seq=545 receive_seq=545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999654 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=2136 bytes_read=8658 bytes_retransmit=0 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997044 adj=49993535 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2759 bytes_read=28401 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999413 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1634 bytes_read=75535 bytes_retransmit=0 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999559 adj=31999579 coil_temp=36.9 refs=0 mcu_temp=35.56 supply_voltage=3.014 sysload=0.15 cputime=3429.819 memavail=1400552 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.1 pwm=0.000
Stats 71148.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5311 bytes_read=32615 bytes_retransmit=9 bytes_invalid=0 send_seq=546 receive_seq=546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999655 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=2142 bytes_read=8674 bytes_retransmit=0 bytes_invalid=0 send_seq=331 receive_seq=331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997011 adj=49993825 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2765 bytes_read=28501 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999426 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1640 bytes_read=75891 bytes_retransmit=0 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999559 adj=31999576 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.15 cputime=3429.874 memavail=1400552 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=53.1 pwm=0.000
Stats 71149.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5317 bytes_read=32718 bytes_retransmit=9 bytes_invalid=0 send_seq=547 receive_seq=547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999649 rpi: mcu_awake=0.001 mcu_task_avg=0.000020 mcu_task_stddev=0.000020 bytes_write=2148 bytes_read=8690 bytes_retransmit=0 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996979 adj=49994130 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2771 bytes_read=28601 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999363 adj=63999436 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1646 bytes_read=76247 bytes_retransmit=0 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999559 adj=31999576 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.22 cputime=3429.908 memavail=1402060 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.9 pwm=0.000
Stats 71150.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5323 bytes_read=32821 bytes_retransmit=9 bytes_invalid=0 send_seq=548 receive_seq=548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999643 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000017 bytes_write=2154 bytes_read=8719 bytes_retransmit=0 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996951 adj=49994415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2777 bytes_read=28743 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999361 adj=63999571 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1658 bytes_read=76619 bytes_retransmit=0 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999557 adj=31999609 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.22 cputime=3429.932 memavail=1402060 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.8 pwm=0.000
Stats 71151.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5329 bytes_read=32953 bytes_retransmit=9 bytes_invalid=0 send_seq=549 receive_seq=549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999638 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000017 bytes_write=2160 bytes_read=8735 bytes_retransmit=0 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996928 adj=49994663 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2783 bytes_read=28843 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999554 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1664 bytes_read=76975 bytes_retransmit=0 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999556 adj=31999597 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.22 cputime=3429.956 memavail=1401564 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.7 pwm=0.000
Stats 71152.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5335 bytes_read=33070 bytes_retransmit=9 bytes_invalid=0 send_seq=550 receive_seq=550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999636 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000017 bytes_write=2166 bytes_read=8751 bytes_retransmit=0 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996910 adj=49994928 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2789 bytes_read=28943 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999530 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.6  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1670 bytes_read=77331 bytes_retransmit=0 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999555 adj=31999596 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.22 cputime=3429.979 memavail=1400588 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.2 pwm=0.000
Stats 71153.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5341 bytes_read=33173 bytes_retransmit=9 bytes_invalid=0 send_seq=551 receive_seq=551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999633 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000017 bytes_write=2172 bytes_read=8767 bytes_retransmit=0 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996896 adj=49995181 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2795 bytes_read=29071 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999356 adj=63999506 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1676 bytes_read=77687 bytes_retransmit=0 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999594 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.22 cputime=3430.004 memavail=1402920 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.0 pwm=0.000
Stats 71154.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5347 bytes_read=33305 bytes_retransmit=9 bytes_invalid=0 send_seq=552 receive_seq=552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999638 rpi: mcu_awake=0.001 mcu_task_avg=0.000017 mcu_task_stddev=0.000017 bytes_write=2178 bytes_read=8783 bytes_retransmit=0 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996890 adj=49995439 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2801 bytes_read=29171 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999355 adj=63999491 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1682 bytes_read=78043 bytes_retransmit=0 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999587 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.20 cputime=3430.050 memavail=1402256 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=52.2 pwm=0.000
Stats 71155.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5353 bytes_read=33408 bytes_retransmit=9 bytes_invalid=0 send_seq=553 receive_seq=553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999638 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=2184 bytes_read=8812 bytes_retransmit=0 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996889 adj=49995707 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2807 bytes_read=29271 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999355 adj=63999452 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1688 bytes_read=78399 bytes_retransmit=0 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999583 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.20 cputime=3430.104 memavail=1402256 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.9 pwm=0.000
Stats 71156.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5359 bytes_read=33511 bytes_retransmit=9 bytes_invalid=0 send_seq=554 receive_seq=554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999638 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=2190 bytes_read=8828 bytes_retransmit=0 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996894 adj=49996015 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2813 bytes_read=29413 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999354 adj=63999456 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1694 bytes_read=78755 bytes_retransmit=0 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999589 coil_temp=36.9 refs=0 mcu_temp=35.58 supply_voltage=3.014 sysload=0.20 cputime=3430.160 memavail=1402256 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.4 pwm=0.000
Stats 71157.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5365 bytes_read=33657 bytes_retransmit=9 bytes_invalid=0 send_seq=555 receive_seq=555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999644 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=2196 bytes_read=8844 bytes_retransmit=0 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996902 adj=49996333 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2819 bytes_read=29513 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999355 adj=63999453 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1700 bytes_read=79111 bytes_retransmit=0 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999595 coil_temp=36.9 refs=0 mcu_temp=35.57 supply_voltage=3.014 sysload=0.20 cputime=3430.215 memavail=1402260 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.6 pwm=0.000
Stats 71158.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5371 bytes_read=33760 bytes_retransmit=9 bytes_invalid=0 send_seq=556 receive_seq=556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999648 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=2202 bytes_read=8860 bytes_retransmit=0 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996916 adj=49996608 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2825 bytes_read=29613 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999444 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=35.3 raspberry_pi: temp=32.6  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1706 bytes_read=79467 bytes_retransmit=0 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999582 coil_temp=36.9 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.20 cputime=3430.271 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.4 pwm=0.000
Stats 71159.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5377 bytes_read=33863 bytes_retransmit=9 bytes_invalid=0 send_seq=557 receive_seq=557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999653 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=2208 bytes_read=8876 bytes_retransmit=0 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996932 adj=49996895 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2831 bytes_read=29741 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999450 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1712 bytes_read=79823 bytes_retransmit=0 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999577 coil_temp=36.9 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.19 cputime=3430.326 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.1 pwm=0.000
Stats 71160.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5383 bytes_read=33995 bytes_retransmit=9 bytes_invalid=0 send_seq=558 receive_seq=558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=2214 bytes_read=8905 bytes_retransmit=0 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996954 adj=49997163 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2837 bytes_read=29841 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999435 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=33.6  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1718 bytes_read=80179 bytes_retransmit=0 bytes_invalid=0 send_seq=285 receive_seq=285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999577 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.19 cputime=3430.383 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=51.0 pwm=0.000
Stats 71161.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5389 bytes_read=34098 bytes_retransmit=9 bytes_invalid=0 send_seq=559 receive_seq=559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=2220 bytes_read=8921 bytes_retransmit=0 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49996980 adj=49997453 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2843 bytes_read=29955 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999358 adj=63999437 Octopus_V1.1_F446: temp=26.7 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1724 bytes_read=80535 bytes_retransmit=0 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999566 coil_temp=36.9 refs=0 mcu_temp=35.54 supply_voltage=3.014 sysload=0.19 cputime=3430.437 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.7 pwm=0.000
Stats 71162.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5395 bytes_read=34215 bytes_retransmit=9 bytes_invalid=0 send_seq=560 receive_seq=560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999659 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=2226 bytes_read=8937 bytes_retransmit=0 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997010 adj=49997740 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2849 bytes_read=30083 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999360 adj=63999441 Octopus_V1.1_F446: temp=26.8 EBB42_v1.2_T0: temp=35.7 raspberry_pi: temp=33.6  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1730 bytes_read=80891 bytes_retransmit=0 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999574 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.19 cputime=3430.494 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.7 pwm=0.000
Stats 71163.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5401 bytes_read=34347 bytes_retransmit=9 bytes_invalid=0 send_seq=561 receive_seq=561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=2232 bytes_read=8953 bytes_retransmit=0 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997046 adj=49998056 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2855 bytes_read=30183 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999481 Octopus_V1.1_F446: temp=26.5 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1736 bytes_read=81247 bytes_retransmit=0 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999584 coil_temp=36.9 refs=0 mcu_temp=35.53 supply_voltage=3.014 sysload=0.19 cputime=3430.549 memavail=1402036 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.3 pwm=0.000
Stats 71164.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5407 bytes_read=34450 bytes_retransmit=9 bytes_invalid=0 send_seq=562 receive_seq=562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000019 mcu_task_stddev=0.000018 bytes_write=2238 bytes_read=8969 bytes_retransmit=0 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997082 adj=49998382 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2861 bytes_read=30283 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999360 adj=63999481 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1742 bytes_read=81603 bytes_retransmit=0 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999594 coil_temp=37.0 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.65 cputime=3430.603 memavail=1401280 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.3 pwm=0.000
Stats 71165.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5413 bytes_read=34553 bytes_retransmit=9 bytes_invalid=0 send_seq=563 receive_seq=563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999658 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000022 bytes_write=2244 bytes_read=8998 bytes_retransmit=0 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997118 adj=49998625 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2867 bytes_read=30411 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999485 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.5 raspberry_pi: temp=33.1  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1748 bytes_read=81959 bytes_retransmit=0 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999553 adj=31999603 coil_temp=37.0 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.65 cputime=3430.659 memavail=1401288 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.2 pwm=0.000
Stats 71166.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5419 bytes_read=34685 bytes_retransmit=9 bytes_invalid=0 send_seq=564 receive_seq=564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999662 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000022 bytes_write=2250 bytes_read=9014 bytes_retransmit=0 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997159 adj=49998828 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2873 bytes_read=30525 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999359 adj=63999473 Octopus_V1.1_F446: temp=26.4 EBB42_v1.2_T0: temp=35.4 raspberry_pi: temp=34.1  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1754 bytes_read=82315 bytes_retransmit=0 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999552 adj=31999615 coil_temp=36.9 refs=0 mcu_temp=35.56 supply_voltage=3.014 sysload=0.65 cputime=3430.701 memavail=1401760 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.1 pwm=0.000
Stats 71168.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5425 bytes_read=34798 bytes_retransmit=9 bytes_invalid=0 send_seq=565 receive_seq=565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999656 rpi: mcu_awake=0.001 mcu_task_avg=0.000021 mcu_task_stddev=0.000022 bytes_write=2256 bytes_read=9030 bytes_retransmit=0 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997196 adj=49999056 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=2879 bytes_read=30625 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999357 adj=63999447 Octopus_V1.1_F446: temp=26.6 EBB42_v1.2_T0: temp=35.6 raspberry_pi: temp=33.6  heater_bed: target=0 temp=46.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1760 bytes_read=82671 bytes_retransmit=0 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999551 adj=31999586 coil_temp=36.9 refs=0 mcu_temp=35.55 supply_voltage=3.014 sysload=0.65 cputime=3430.724 memavail=1401788 print_time=12.146 buffer_time=0.000 print_stall=0 extruder: target=0 temp=50.1 pwm=0.000